Quickie® GP™/GPV Owner`s Manual
Contents
1. 12 s Weight Limit a hall 12 b Weight 2 c Getting to Know Your Chair sere 12 d To Reduce The Risk of an Accident 12 e Safety Check List 13 f Changes amp Adjustments 13 g Environmental Conditions 13 session lan ll nav 4 Street Use 14 jz Motor Vehicle Safety retrace techn 14 k When You Need Help rrt rte 15 WARNINGS FALLS amp TIP OVERS l6 a Genter of Balance ioni blanu ns lu lana l6 b Dressing or Changing Clothes ss l6 cs Mheelies in um hen tetris 17 d Obstacles 17 e Reaching or Leaning 18 f Moving Backward 18 g Ramps Slopes amp Side Hills sss 19 MICHI e o arilo ia 20 i Curbs Be Steps puak aasawa nn 20 2 0 21 WARNINGS FOR SAFE 22 a Learning To Do A Wheelie u ua seen 22 b Descending A Curb or Single Step 22 c Climbing A Curb or Single Step sss 23 d Climbing StalES rer tete iet 23 e Descending Stairs Ju aaa reiten hr 23 f Maintenance nn 24 WARNINGS COMPONENTS 8 OPTIONS2. 930301 Rev D X SET UP amp ADJUSTMENT G REAR AXLES The most important adjustment on your Quickie wheelchair is the position of the rear axle The center of gravity wheel camber and wheelbase are all determined by the axle adjustment Use a torque setting of 100 in Ibs when adjusting rear axle Center of Gravity Moving the center of gravity to the front will lighten the force required to turn the chair The further back the axle the more stable the chair becomes The center of gravity is adjusted by moving the rear axle forward or backward on the frame Moving the axle forward will increase your turning speed and lighten the front end Wheel Camber The wheel camber adjustment provides greater side to side stability due to the increased width and angle of the wheel base The wheel camber adjustment also allows for quicker turning and greater access to the top of the handrims Wheel camber is preset at the factory at 7 More or less camber can be obtained by increasing or decreasing the number of camber washers located between the axle plates and the frame Wheel Base Width Adjustment a Loosen two axle nuts b Reposition the axle sleeve in the desired slot c Retighten nuts d Adjustment must be exactly the same on both sides of the wheelchair Note To achieve the narrowest chair possible axle plates can be mounted on inside frame tubes It may be neces
3. 25 a Anti Tip Tubes Optional ttes 25 b lp e 25 c Cushions amp Sling Seats rt ttti its 25 d Fasteners 26 26 f Pneumatic Tires 26 g Positioning Belts Optional u sss 27 9 930301 Rev D XI XII XII 930301 Rev D 111 TABLE OF CONTENTS h Power DRIVE 27 i Push Handles Optional Jtt iiec 27 j Quickie Release Axles u 28 6 Rear Dc m 28 Rear Wheel 0 necem ate oo e ent 28 m Modified Seat Systems uU eerte 29 n Jpholstery Fabric ttc retro chri ttem iiber cita 29 CHAIR BASICS iiciin 30 a To Mount and Remove Rear Wheels Optional 30 SET UP AND ADJUSTMENTS ee 3l a Axles Quick Release 0 3l b Swing Away Adjustable Armrest sene 3l c Height Adjustable Armrest Optional 32 d Backrest 34 e Seat Sling 34 7 33 g Rear Axles uy anu aqa awan tetti teet coa ee eee cage 34 h Wheel Locks iss 35 36 j Swing Away Hangers and Footrests 60 70 70 V or 90 37 k Articulating Legrest or Elevating Legrest Optional 37 Caster FORKS 8 m Caster Plates 38 n Caster Mounting aie 38 o Anti Tip Tubes Optional 7 39 Pe Check Out uu M M 40 TROUBLESHOOTING 4l MAINTENA
4. X SET UP amp ADJUSTMENT D BACKREST The backrest comes standard with a 4 height adjustment Height Adjustment a Remove the backrest upholstery from the frame b You will see the backrest tube which telescopes into the frame and is secured by a screw on the side of the frame c There are four holes inch apart you may choose from to set the back height d After selecting the proper height slide the backrest upholstery back on with the overlap portion unattached e Secure VELCRO style material on side tubes and attach the excess overlap Back Angle Adjustment Folding Backrest An 8 5 angle adjustment is standard on this Quickie wheelchair a Turning the eccentric bolt on the backrest hinge plate will increase or decrease the back angle b The adjustment on each side of the chair must be exactly equal SEAT SLING The seat sling can be adjusted through the use of VELCRO style retaining material beneath the seat Adjustment a Remove the screws retaining the left side seat sling b Re adjust VELCRO style material to increase the tension in the seat sling c Replace screws d lf there is any difficulty in reattaching the screws try using a probe to help line up the holes CUSHION OPTIONAL Installation a Place cushion on seat sling with VELCRO side down The beveled edge of the cushion should be in front b Press firmly into place
5. Section VII 2 Do not try to climb or descend a curb or step alone UNLESS you are a skilled rider of this chair and a You can safely do a wheelie and b You are sure you have the strength and balance to do so Unlock and rotate anti tip tubes up out of the way so they do not interfere 4 Do not try to climb a high curb or step more than 4 inches high UNLESS you have help Doing so may cause your chair to exceed its balance point and tip over 5 Go straight up and straight down a curb or step If you climb or descend at an angle a fall or tip over is likely 6 Beaware that the impact of dropping down from a curb or step can damage your chair or loosen fasteners If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others ei 930301 Rev D 20 b Avoid putting weight on the footrests as this may cause the chair to tip VI WARNINGS FALLS 8 TIP OVERS J STAIRS A WARNING I NEVER use this chair on stairs UNLESS you have someone to help you Doing so is likely to cause a fall or tip over 2 Persons who help you should read and follow the warnings For Attendants p 15 and the For Safe Use Section VII If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others K ESCALATORS A WARNING NEVER use this chair on an esca
6. then a second and a third if needed You may need to look farther to find the best solution for a specific problem Note To keep track of your progress make only ONE change at a time Ng RJ 888 4 88 c es AA O 6 S lt S Z V G A AA PA ZZ U U S DA SEL SE EVA DA RAS VA SSS SOLUTIONS Make sure tire pressure is correct and equal in both rear tires and front caster tires if pneumatic Make sure all nuts and bolts are snug Make sure all spokes and nipples are tight on radial spoke wheels Use Tri Flow Lubricant Teflon based between all modular frame connections and parts Check for proper caster plate adjustment See instructions for caster plate adjustment Add a spacer washer between the plastic saddle and the caster plate on the top of the left caster plate Add a spacer washer between the plastic saddle and the caster plate on the top of the right caster plate Add a spacer washer between the plastic saddle and the caster plate on the bottom right caster plate retaining bolts Add a spacer washer between the plastic saddle and the caster plate on the bottom right caster plate retaining bolts Make sure there is an equal number of camber washers on each axle plate Make sure both front casters touch the ground simultaneously If they do not add the proper spacers between the bottom bearing of the caster plate and fork stem nut until they do Make sure you check for this problem on a flat surfa
7. Wet or slippery surfaces b A change in grade on a slope or a lip bump or depression These may cause a fall or tip over c A drop off at the bottom of a slope A drop off of as small as 3 4 inch can stop a front caster and cause the chair to tip forward 8 To Reduce The Risk Of A Fall Or Tip Over a Lean or press your body UPHILL This will help adjust for the change in the center of balance caused by the slope or side hill b Keep pressure on the handrims to control your speed on a down slope If you go too fast you may lose control c Ask for help any time you are in doubt 9 Ramps At Home amp Work For your safety ramps at home and work must meet all legal requirements for your area We recommend a Width At least four feet wide b Guardrails To reduce the risk of a fall sides of ramp must have guardrails or raised borders at least three inches high c Slope Not more than a 1076 grade Surface Flat and even with a thin carpet or other non skid material Make sure there is no lip bump or depression e Bracing Ramp must be STURDY You may need bracing so ramp does not bow when you ride on it f Avoid A Drop Off You may need a section at the top or bottom to smooth out the transition If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 19 930301 Rev D WARNINGS FALLS amp TIP OVERS H TRANSFER
8. a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 12 V GENERAL WARNINGS E SAFETY CHECKLIST WARNING Before Each Use Of Your Chair I Make sure the chair rolls easily and that all parts work smoothly Check for noise vibration or a change in ease of use They may indicate low tire pressure loose fasteners or damage to your chair 2 Repair any problem Your authorized supplier can help you find and cor rect the problem 3 Check to see that both quick release rear axles are locked When locked the axle button will pop out fully If not locked the wheel may come off and cause you to fall 4 If your chair has anti tip tubes lock them in place Note See Anti Tip Tubes Section VIII for times you should not use them If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others F CHANGES amp ADJUSTMENTS A WARNING I If you modify or adjust this chair it may increase the risk of a tip over UNLESS you make other changes as well 2 Consult your authorized supplier BEFORE you modify or adjust your chair 3 We recommend that you use anti tip tubes until you adapt to the change and are sure you are not at risk to tip over 4 Unauthorized modifications or use of parts not supplied or approved by Sunrise may change the chair structure This will void t
9. as you Figure A slide axle 2 into axle sleeve 3 d Release button to lock axle in sleeve 3 Axle Sleeve Adjust axle if it does not lock Follow steps on p 31 e Repeat steps on other side 2 To Remove Wheel a Depress quick release button 1 fully b Remove wheel by sliding axle 2 out of axle sleeve 3 c Repeat steps on other side 930301 Rev D 30 X SET UP amp ADJUSTMENT Note Setting the wheelchair on a table or on a flat surface such as a table or on a flat surface such as a workbench helps make these procedures easier Note on Torque Setting A torque setting is the optimum tightening which should be made on a particular fastener A torque wrench which measures in lbs Should be used when tightening fasteners on Quickie wheel chairs Unless otherwise noted use a torque setting of 60 in lbs When setting up this wheelchair AXLES QUICK RELEASE a Depress the quick release button on the axle b Slide through wheel hub and into axle sleeve until it locks c The axle is not secured until the out side quick release button pops out to its fully extended position d The ball bearing on the opposite end of the axle must be fully visible beyond the end of the axle sleeve SWING AWAY ADJUSTABLE ARMRESTS Installation a Slide armrest into receiver on rear frame tube Swinging Away a Push armrest to the side and out of the way when transferring Removing
10. A WARNING NEVER use this chair for weight training if total weight rider plus equip ment exceeds 250 pounds If you do exceed the limit damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others GETTING TO KNOW YOUR CHAIR A WARNING Every wheelchair is different Take the time to learn the feel of this chair before you begin riding Start slowly with easy smooth strokes If you are used to a different chair you may use too much force and tip over If you use too much force damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others TO REDUCE THE RISK OF AN ACCIDENT A WARNING I BEFORE riding you should be trained in the safe use of this chair by your health care advisor 2 Practice bending reaching and transfers until you know the limit of your ability Have someone help you until you know what can cause a fall or tip over and how to avoid doing so 3 Beaware that you must develop your own methods for safe use best suited to your level of function and ability 4 NEVER try a new maneuver on your own until you are sure you can do it safely 5 Get to know the areas where you plan to use your chair Look for hazards and learn how to avoid them 6 Use anti tip tubes unless you are a skilled rider of this chair and are sure you are not at risk to tip over If you fail to heed these warnings damage to your chair
11. Armrest a Pull armrest straight out of bracket Quick Release Button 930301 Rev D X SET UP amp ADJUSTMENT C HEIGHT ADJUSTABLE ARMRESTS OPTIONAL I Installation a Slide the outer armpost into the receiver mounted to the wheelchair frame b The armrest will automatically lock into place 2 Height Adjustment a Rotate release lever to second stop b Slide armrest pad up or down to desired height c Return lever to locked position Height Adjustable against armpost Armrest Key d Push arm pad until upper armpost Outer armpost locks firmly into place 2 Standard receiver 3 Removing Armrest 3 Release lever a Rotate release lever to first stop and 4 Armrest pad remove the armrest 5 Transfer bar 4 Replacing Armrest 6 Side panel a Slide armrest back into receiver 7 Outer armpost tension b Return release lever to locked adjustment set screws position against armpost 8 Inner armpost 5 Adjusting Armrest Receiver Fit 9 Receiver adjustment bolts To tighten or loosen the fit of the outer armpost in the receiver a Loosen the four bolts on the sides of the receiver b With the armrest in the receiver squeeze the receiver to achieve the desired fit c Tighten the four bolts 6 Adjusting Inner Armpost Fit a Two set screws are installed in the outer armpost b Turn the set screws in or out until the desired fit is achieved 930301 Rev D 32
12. In most states wheelchairs are not legal for use on public roads Be alert to the danger of motor vehicles on roads or in parking lots I At night or when lighting is poor use reflective tape on your chair and clothing 2 Due to your low position it may be hard for drivers to see you Make eye contact with drivers before you go forward When in doubt yield until you are sure it is safe If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others MOTOR VEHICLE SAFETY A WARNING Quickie wheelchairs do not meet federal standards for motor vehicle seating I NEVER let anyone sit in this chair while in a moving vehicle a ALWAYS move the rider to an approved vehicle seat b AL WAYS secure the rider with proper motor vehicle restraints 2 n an accident or sudden stop the rider may be thrown from the chair Wheelchair seat belts will not prevent this and further injury may result from the belts or straps 3 NEVER transport this chair in the front seat of a vehicle It may shift and interfere with the driver 4 ALWAYS secure this chair so that it cannot roll or shift 5 Do not use any chair that has been involved in a motor vehicle accident If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 14 V GENERAL WARNING
13. Sunrise is prohibited for transit use If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others N UPHOLSTERY FABRIC WARNING I Replace worn or torn fabric of seat and seat back as soon as you can If you fail to do so the seat may fail 2 Sling fabric will weaken with age and use Look for fraying or thin spots or stretching of fabrics at rivet holes 3 Dropping down into your chair will weaken fabric and result in the need to inspect and replace the seat more often 4 Beaware that laundering or excess moisture will reduce flame retardation of the fabric If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 29 930301 Rev D IX CHAIR BASICS A TO MOUNT 8 REMOVE REAR WHEELS OPTIONAL WARNING Do not use this chair UNLESS you are sure both guick release axles are locked An unlocked axle may come off during use and cause a fall Note Axle is not locked until a The guick release button pops out fully Fig A b The ball bearings are fully visible on the outside of the sleeve Fig A I To Install Wheel a Depress quick release button 1 fully This will release tension on ball bear ings at other end b Insert axle through hub of rear wheel 1 Quick Release Button Keep pressure on button 1
14. chair a fall tip over or loss of control may occur and cause severe injury to the rider or others B DRESSING OR CHANGING CLOTHES A WARNING Your weight may shift if you dress or change clothes while seated in this chair To reduce the risk of a fall or tip over I Rotate the front casters until they are as far forward as possible This makes the chair more stable 2 Lock anti tip tubes in place If your chair does not have anti tip tubes back it up against a wall and lock both rear wheels If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 16 VI WARNINGS FALLS amp TIP OVERS C WHEELIES A WARNING Doing a wheelie means balancing on the rear wheels of your chair while the front casters are in the air It is dangerous to do a wheelie as a fall or tip over may occur However if you do it safely a wheelie can help you overcome curbs and obstacles I Consult your doctor nurse or therapist to find out if you are a good candidate to learn to do a wheelie 2 Do not attempt a wheelie UNLESS you are a skilled rider of this chair or you have help Note See p 22 for steps to learn to do a wheelie If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others D OBSTACLES A WARNING Obstac
15. mild soap at least once a month b Protect the paint with a coat of non abrasive auto wax every three months 2 Axles and Moving Parts a Clean around axles and moving parts WEEKLY with a slightly damp not wet cloth b Wipe off or blow away any fluff dust or dirt on axles or moving parts c Note You do not need to grease or oil the chair 3 Upholstery a Hand wash machine washing may damage fabric b Drip dry only DO NOT machine dry as heat will damage fabric E STORAGE TIPS l Store your chair in a clean dry area If you fail to do so parts may rust or corrode 2 Before using your chair make sure it is in proper working order Inspect and service all items on the Maintenance Chart See p 42 3 If stored for more than three months have your chair inspected by an authorized supplier before use 43 930301 Rev D XIII SUNRISE LIMITED WARRANTY A FOR LIFETIME Sunrise warrants the frame and cross brace if applicable of this wheelchair against defects in materials and workmanship for the life of the original purchaser The expected life of this frame is five years B FOR ONE 1 YEAR We warrant all Sunrise made parts and components of this wheelchair against defects in materials and workmanship for one year from the date of first con sumer purchase C LIMITATIONS I We do not warrant a Tires and tubes upholstery pads and push handle grips b Damage from neglect accident misuse or from improper in
16. to correct position c The end of the plug is tapped so a 3 4 x 20 bolt included with chair may be used to help position the plug at the correct hole d Align predrilled holes in footrest and reinsert bolts Tighten Platform Footplate Angle Adjustment Optional a Loosen flathead screws b Reposition footplate to desired angle and retighten screws 930301 Rev D 36 X SET UP amp ADJUSTMENT SWING AWAY HANGERS AND FOOTRESTS 60 70 70 V or 90 Ouickie GP Swing Away Only Installation a Place swing away pivot saddle into the receiver on front frame tube with the footrest facing outward from the frame b Rotate the footrest inward until it locks into place on locking bolt Removal a To remove footrest push release latch toward the frame b Rotate footrest outward and lift Height Adjustment a Remove retaining bolt in the frame tube b Slide footrest tubes up or down inside frame tube to desired height c Align predrilled holes in footrest and reinsert bolts d Tighten bolts Footplate Angle Adjustment a Loosen the retaining bolt in the frame tube b Reposition footplate to desired angle and retighten bolt ARTICULATING LEGREST OR ELEVATING LEGREST OPTIONAL Installation To install or remove articulating legrest ALR or elevating legrest ELR see instructions for swing away hangers and footrests Adjustme
17. A WARNING It is dangerous to transfer on your own It requires good balance and agility Be aware that there is a point during every transfer when the wheelchair seat is not below you To Avoid A Fall I Work with your health care advisor to learn safe methods a Learn how to position your body and how to support yourself during a transfer b Have someone help you until you know how to do a safe transfer on your own 2 Lock the rear wheels before you transfer This keeps the rear wheels from rolling Note This will NOT keep your chair from sliding away from you or tipping 3 Make sure to keep pneumatic tires properly inflated Low tire pressure may allow the rear wheel locks to slip 4 Move your chair as close as you can to the seat you are transferring to If possible use a transfer board 5 Rotate the front casters until they are as far forward as possible 6 If you can remove or swing footrests out of the way a Make sure your feet do not catch in the space between the footrests 7 Make sure armrests are out of the way and do not interfere 8 Transfer as far back onto the seat surface as you can This will reduce the risk that the chair will tip or move away from you If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others I CURBS amp STEPS A WARNING I Each person who helps you should read and follow the warnings For Safe Use
18. NCE notiert tette etis 42 JntrOdUCtON mr 42 b Maintenance Chart uya awana 42 c Maintenance TIPS eee alk 43 d Cleaning iii 43 e Storage TIPS unu isi 43 SUNRISE LIMITED 44 a For Lifetime au e amana aun rn ab 44 DM For i Rm 44 FON EO dicii ukush aula maia ih 44 d What We Will 44 e What You Must Do 44 f Notice to Consumers 44 IV NOTICE READ BEFORE USE A CHOOSE THE RIGHT CHAIR amp SAFETY OPTIONS Sunrise provides a choice of many wheelchair styles to meet the needs of the wheelchair rider However final selection of the type of wheelchair options and adjustments rests solely with you and your health care advisor Choosing the best chair and set up for your safety depends on such things as I Your disability strength balance and coordination 2 The types of hazards you must overcome in daily use where you live and work and other places you are likely to use your chair 3 The need for options for your safety and comfort such as anti tip tubes positioning belts or special seating systems REVIEW THIS MANUAL OFTEN Before using this chair you and each person who may assist you should read this entire manual and make sure to follow all instructions Review the warnings often until they are second nature to you
19. Quickie GP GPV Instruction Manual es Warranty SUPPLIER THIS MANUAL MUST BE GIVEN TO THE RIDER OF THIS WHEELCHAIR RIDER BEFORE USING THIS WHEELCHAIR READ THIS ENTIRE MANUAL AND SAVE FOR FUTURE REFERENCE SUNRISE MEDICAL II YOUR CHAIR AND ITS PARTS I INTRODUCTION SUNRISE LISTENS Thank you for choosing a Quickie wheelchair We want to hear your questions or comments about this manual the safety and reliability of your chair and the service you receive from your Sunrise supplier Please feel free to write or call us at the address and telephone number below SUNRISE HOME HEALTHCARE GROUP MOBILITY PRODUCTS DIVISION Customer Service Department 7477 East Dry Creek Parkway Longmont Colorado 80503 303 218 4500 or 800 456 8165 Be sure to return your warranty card and let us know if you change your address This will allow us to keep you up to date with information about safety new products and options to increase your use and enjoyment of this wheel chair If you lose your warranty card call or write and we will gladly send you a new one FOR ANSWERS TO YOUR QUESTIONS Your authorized supplier knows your wheelchair best and can answer most of your questions about chair safety use and maintenance For future reference fill in the following Supplier Address I Backrest 10 21 Aluminum Handrim 2 24 Pneumatic Tires Spokes Telephone 3 Seat Cushion 12
20. Rear Wheel Hub Serial Date Purchased 4 Seat Sling 13 Quick Release Axle 5 Low Mount Wheel Lock 14 Aluminum Wheel Rim 6 Leg Strap 15 Axle Plate 7 Caster Plate 16 Caster Housing 8 Footrest 17 Caster Fork 9 Footrest Impact Guard 18 Caster Wheel 930301 Rev D 930301 Rev D IN Iw lt 9 ON U N 930301 Rev D II YOUR CHAIR AND Backrest Pneumatic Tires Seat Cushion Seat Sling Wheel Lock Leg Strap Caster Plate Footrest Footrest Impact Guard QUICKIE GPV QUICKIE GPV COMPETITION ITS PARTS Spokes Aluminum Handrim Rear Wheel Hub Quick Release Axle Aluminum Wheel Rim Axle Plate Caster Housing Caster Fork Caster Wheel 0 00 OUS O II YOUR CHAIR AND QUICKIE Backrest Pneumatic Tires Seat Cushion Seat Sling Wheel Lock Heel Loop Caster Plate Swing Away Footrest Footplate G P ITS PARTS 6 5 0 11 12 13 14 15 16 17 18 Aluminum Handrim Spokes Rear Wheel Hub Quick Release Axle Aluminum Wheel Rim Axle Plate Caster Housing Caster Fork Caster Wheel 930301 Rev D II YOUR CHAIR AND ITS PARTS QUICKIE GP QUICKIE GPV QUICKIE GPV COMPETITION QUICKIE GP SWING AWAY Colors Blue black red midnight purple teal pearl pink lavender forest green burgundy antique bronze yellow blue green candy teal candy razzberry candy purple Custom splatter bla
21. S K WHEN YOU NEED HELP A WARNING For The Rider Make sure that each person who helps you reads and follows all warnings and instructions that apply For Attendants I Work with the rider s doctor nurse or therapist to learn safe methods best suited to your abilities and those of the rider 2 Tell the rider what you plan to do and explain what you expect the rider to do This will put the rider at ease and reduce the risk of an accident 3 Make sure the chair has push handles They provide secure points for you to hold the rear of the chair to prevent a fall or tip over Check to make sure push handle grips will not rotate or slip off 4 To prevent injury to your back use good posture and proper body mechanics When you lift or support the rider or tilt the chair bend your knees slightly and keep your back as upright and straight as you can 5 Remind the rider to lean back when you tilt the chair backward 6 When you descend a curb or single step slowly lower the chair in one easy movement Do not let the chair drop the last few inches to the ground This may damage the chair or injure the rider 7 To avoid tripping unlock and rotate anti tip tubes up out of the way ALWAYS lock the rear wheels and lock anti tip tubes in place if you must leave the rider alone even for a moment This will reduce the risk of a tip over or loss of control of the chair If you fail to heed these warnings damage to your chair a fall tip ov
22. WARNINGS The word WARNING refers to a hazard or unsafe practice that may cause severe injury or death to you or to other persons The Warnings are in three main sections as follows I V GENERAL WARNINGS Here you will find a safety checklist and a summary of risks you need to be aware of before you ride this chair 2 VI WARNINGS FALLS amp TIP OVERS Here you will learn how to avoid a fall or tip over while you perform daily activities in your chair 3 VII WARNINGS FOR SAFE USE Here you will learn about practices for the safe use of your chair 4 VIII WARNINGS COMPONENTS amp OPTIONS Here you will learn about the components of your chair and options you can select for safety Consult your authorized supplier and your health care advi sor to help you choose the best set up and options for safe use Note Where they apply you will also find Warnings in other sections of this manual Heed all warnings in this section If you fail to do so a fall tip over or loss of control may occur and cause severe injury to the rider or others Rev D 930301 A n AV GENERAL WARNINGS WEIGHT LIMIT A WARNING NEVER exceed the weight limit of 250 pounds 113 6 kilograms for combined weight of rider and items carried If you do exceed the limit damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others WEIGHT TRAINING
23. all heat treated tennis heat treated basketball Handrims Standard Aluminum Option Plastic coated long tabs Projections Option Vertical oblique 6 8 10 12 Wheel Locks Standard Low mount Option High push high pull high scissor swing away 6 or 9 extension handles All features may not be available with some chair setups or in conjunction with another chair feature Please consult your authorized supplier for more information lt 9 ON Uu A U N Backrest Tires Seat Cushion Seat Sling Wheel Lock Leg Strap Caster Plate Footrest Footrest Impact Guard YOUR CHAIR AND 10 12 13 14 15 6 17 18 ITS PARTS Handrim Spokes Rear Wheel Hub Ouick Release Axle Aluminum Wheel Rim Axle Plate Caster Housing Caster Fork Caster Wheel 930301 Rev D II YOUR CHAIR AND ITS PARTS GUICKIE TI TITANIUM Colors Natural titanium finish Chair Parts Black Frame Dimensions Frame width Standard 14 18 seat width 1 2 narrower Sling depth with Standard frame lengths 14 21 1 49 15 21 1 4 16 21 1 4 Cushion 2 Backrest Non folding fixed 9 16 Folding adjustable 1 14 12 16 14 18 16 20 Backrest Options Push handles Footrests Rigid Regular long Casters Standard 5 low profile polyurethane with aluminum caster rims Option 3 micros 6 pneumatic 6 polyurethane composite caster
24. ce 41 930301 Rev D A INTRODUCTION I Proper maintenance will improve performance and extend the useful life of your chair 2 Clean your chair regularly This will help you find loose or worn parts and make your chair easier to use 3 Repair or replace loose worn bent or damaged parts before using this chair 4 To protect your investment have all major maintenance and repair work done by your authorized supplier A WARNING If you fail to heed these warnings your chair may fail and cause severe injury to the rider or others I Inspect and maintain this chair strictly per chart 2 If you detect a problem make sure to service or repair the chair before use 3 At least once a year have a complete inspection safety check and service of your chair made by an authorized supplier B MAINTENANCE CHART Quick Release Axles Wheels tires and spokes Casters Anti tip tubes Upholstery Service by Authorized Supplier 930301 Rev D 42 C MAINTENANCE TIPS I Axles Axle Sleeves Check axles and axle sleeves every six months to make sure they are tight Loose sleeves will damage the axle plate and will affect performance 2 Tire Air Pressure Check air pressure in pneumatic tires at least ONCE A WEEK The wheel locks will not grip properly if you fail to maintain the air pressure shown on tire sidewall D CLEANING I Paint Finish a Clean the paint finish with
25. ck teal chase purple chase Chair Parts Standard Black Frame Dimensions Frame width Standard 12 20 Frame height Standard 10 front 9 rear Option 9 1 4 front 8 1 4 rear 11 front 10 rear Sling depth Standard 15 Option 14 16 17 18 Cushion 2 3 4 Backrest Non folding fixed 8 6 Folding adjustable Standard 1 14 Option 12 16 16 20 14 18 push handles adjustable upholstery Footrests Standard rigid composite Option platform platform flip up foam 90 degree footboard extended extension tubes Casters Standard 5 polyurethane Option 3 micros 6 pneumatic or polyurethane 3 4 longer fork stem bolt 1 2 longer fork stem bolt multi positioning caster plate caster pin locks quick release caster stems Armrests Option padded swing away height adjustable Stroller handles Option regular tall 930301 Rev D gt Axles Plate Standard Adjustable axle plate Option Double slot index amputee Axles Standard Stainless steel Option Titanium quad release axle nuts Anti Tips Option Rear anti tip tubes Rear Wheels Tire types Standard Rear wheels Standard Spoke Option Mag Tire Size Standard 24 Option 22 26 Tire types Standard pneumatic Option Pneumatic w airless insert full profile polyurethane low profile polyurethane Kevlar high pressure clinchers latex tubular turbo tread tennis basketb
26. crews on the top of each clamp b Slide assembly toward rear wheel until clamp embeds into tire to prevent wheel movement when in locked position c Adjust angle position d Tighten screws 930301 Rev D X SET UP amp ADJUSTMENT High Mount Push to Lock or Pull to Lock Wheel Locks a Loosen the screws on the top of each clamp b Using a 3 16 Allen wrench turn one of the screws counterclockwise one quarter turn c Repeat the same process with the second of the two screws d Alternately loosen the screws two turns each until both screws are removed e Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to prevent wheel movement when in the locked position Tighten screws Swing Away Wheel Locks a Loosen the screws on the top of each clamp b Using a 3 16 allen wrench turn one of the screws counterclockwise one quarter turn c Repeat the same process with the second of the two screws d Alternately loosen the screws two turns each until both screws are removed e Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to prevent wheel movement when in the locked position f Tighten screws FOOTREST Use a torque of 100 in lbs when adjusting footplate Height Adjustment a Remove bolts on both sides of footrest and loosen footplate b Remove footrest tubes and slide plug up or down inside tube
27. d a curb or single step going BACKWARD Stay at the rear of the chair 2 Several feet before your reach the edge of the curb or step turn the chair around and pull it backward 3 While looking over your shoulder carefully step back until you are off the curb or stair and standing on the lower level 4 Pull the chair toward you until the rear wheels reach the edge of the curb or step Then allow the rear wheels to slowly roll down onto the lower level 5 When the rear wheels are safely on the lower level tilt the chair back to its balance point This will lift the front casters off the curb or step 6 Keep the chair in balance and take small steps backward Turn the chair around and gently lower front casters to the ground If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 22 VII WARNINGS FOR SAFE USE C CLIMBING A CURB OR SINGLE STEP A WARNING Follow these steps to help the rider climb a curb or single step going FORWARD I Stay behind the chair 2 Face the curb and tilt the chair up on the rear wheels so that the front casters clear the curb or step 3 Move forward placing the front casters on the upper level as soon as you are sure they are past the edge 4 Continue forward until the rear wheels contact the face of the curb or step Lift and roll the rear wheels to the upper level I
28. der needs such a device 4 Use positioning belts only with a rider who can cooperate Make sure the rider can easily remove the belts in an emergency 5 NEVER Use Positioning Belts a As a patient restraint A restraint requires a doctor s order b Ona rider who is comatose or agitated c As a motor vehicle restraint In an accident or sudden stop the rider may be thrown from the chair Wheelchair seat belts will not prevent this and further injury may result from the belts or straps If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others H POWER DRIVE A WARNING Do not install a power drive on any Quickie wheelchair If you do I It will affect the center of balance of your chair and may cause a fall or tip over 2 It will alter the frame and void the warranty If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others I PUSH HANDLES OPTIONAL A WARNING When you have a attendant make sure that this chair has push handles I Push handles provide secure points for an attendant to hold the rear of this chair to prevent a fall or tip over Make sure to use push handles when you have an attendant 2 Check to make sure push handle grips will not rotate or slip off If you fail to heed these warnings damage to your chair a fall tip over
29. dical Inc 7477 East Dry Creek Parkway Longmont Colorado 80503 USA 303 218 4500 800 456 8165 In Canada 800 263 3390 2003 Sunrise Medical 4 03 930301 Rev D
30. er or loss of control may occur and cause severe injury to the rider or others 15 930301 Rev D VI WARNINGS FALLS amp TIP OVERS A CENTER OF BALANCE A WARNING The point where this chair will tip forward back or to the side depends on its center of balance and stability How your chair is set up the options you select and the changes you make may affect the risk of a fall or tip over l The Most Important Adjustments Are a The position of the rear wheels The more you move the rear wheels forward the more likely your chair will tip over backward 2 The Center Of Balance Is Also Affected By a A change in the set up of your chair including The distance between the rear wheels The amount of rear wheel camber The seat height and seat angle Backrest angle b A change in your body position posture or weight distribution c Riding your chair on a ramp or slope d The use of a back pack or other options and the amount of added weight 3 To Reduce The Risk Of An Accident a Consult your doctor nurse or therapist to find out what axle and caster position is best for you b Consult your authorized supplier BEFORE you modify or adjust this chair Be aware that you may need to make other changes to correct the center of balance c Have someone help you until you know the balance points of your chair and how to avoid a tip over d Use anti tip tubes If you fail to heed these warnings damage to your
31. f you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others D CLIMBING STAIRS A WARNING I Use at least two attendants to move a chair and rider up stairs Move the chair and rider BACKWARD up the stairs 3 The person at the rear is in control He or she tilts the chair back to its balance point 4 A second attendant at the front firmly grasps a non detachable part of the front frame and lifts the chair up and over one stair at a time 5 The attendants move to the next stair up Repeat for each stair until you reach the landing If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others E DESCENDING STAIRS A WARNING I Use at least two attendants to move a chair and rider down stairs Move the chair and rider FORWARD down the stairs 3 The person at the rear is in control He or she tilts the chair to the balance point of the rear wheels and rolls it to the edge of the top step 4 A second attendant stands on the third step from the top and grasps the chair frame He or she lowers the chair one step at a time by letting the rear wheels roll over the stair edge 5 The attendants move to the next stair down Repeat for each stair until you reach the landing If you fail to heed these warnings damage to your chair a fall tip over or loss of con
32. he warranty and may cause a safety hazard If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others G ENVIRONMENTAL CONDITIONS A WARNING I Use extra care if you must ride your chair on a wet or slick surface If you are in doubt ask for help 2 Contact with water or excess moisture may cause your chair to rust or corrode This could cause your chair to fail a Do not use your chair in a shower pool or other body of water The chair tubing and parts are not water tight and may rust or corrode from the inside b Avoid excess moisture for example do not leave your chair in a damp bathroom while taking a shower c Dry your chair as soon as you can if it gets wet or if you use water to clean it If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 13 930301 Rev D V GENERAL WARNINGS H TERRAIN A WARNING I Your chair is designed for use on firm even surfaces such as concrete asphalt and indoor floors and carpeting 2 Do not operate your chair in sand loose soil or over rough terrain This may damage wheels or axles or loosen fasteners of your chair If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others I STREET USE A WARNING
33. ir may tip over 3 Keep Anti Tip Tubes Locked In Place UNLESS a You have an attendant or b You have to climb or descend a curb or overcome an obstacle and can safely do so without them At these times make sure anti tip tubes are up out of the way If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others B ARMRESTS A WARNING Armrests detach and will not bear the weight of this chair I NEVER lift this chair by its armrests They may come loose or break 2 Lift this chair only by non detachable parts of the main frame If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others C CUSHIONS amp SLING SEATS A WARNING I Quickie sling seats and standard foam cushions are not designed for the relief of pressure 2 If you suffer from pressure sores or if you are at risk that they will occur you may need a special seat system or a device to control your posture Consult your doctor nurse or therapist to find out if you need such a device for your well being If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 25 930301 Rev D VIII WARNINGS COMPONENTS amp OPTIONS D FASTENERS A WARNING Many of the screws bolts and nuts
34. lator even with an attendant If you do a fall or tip over is likely If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 21 930301 Rev D VII WARNINGS FOR SAFE USE A WARNING Before you assist a rider be sure to read the warnings For Attendants p 15 and follow all instructions that apply Be aware that you will need to learn safe methods best suited to your abilities A LEARNING TO DO A WHEELIE A WARNING Follow these steps to help the rider learn to do a wheelie I Read and follow the warnings for VVHEELIES See p 17 2 Stand at the rear of the chair You must be able to move with the chair to prevent a tip over 3 Keep your hands BENEATH the push handles ready to catch the rider if the chair tips back 4 When you are ready have the rider place his or her hands on the forward part of the handrims 5 Have the rider make a quick BACKWARD movement of the rear wheels quickly followed by a hard FORWARD thrust This will tilt the chair up on the balance point of the rear wheels 6 Have the rider make small movements of the handrims to stay in balance If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others B DESCENDING A CURB OR SINGLE STEP A WARNING Follow these steps to help a rider descen
35. les and road hazards such as potholes and broken pavement can damage your chair and may cause a fall tip over or loss of control To avoid these risks I Keep a lookout for danger scan the area well ahead of your chair as you ride 2 Make sure the floor areas where you live and work are level and free of obstacles 3 Remove or cover threshold strips between rooms 4 Install a ramp at entry or exit doors Make sure there is not a drop off at the bottom of the ramp 5 To Help Correct Your Center Of Balance a Lean your upper body FORWARD slightly as you go UP over an obstacle b Press your upper body BACKWARD as you go DOWN from a higher to a lower level 6 If your chair has anti tip tubes lock them in place before you go UP over an obstacle 7 Keep both of your hands on the handrims as you go over an obstacle 8 Never push or pull on an object such as furniture or a doorjamb to propel your chair If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 17 930301 Rev D VI WARNINGS FALLS 8 TIP OVERS E REACHING OR LEANING A WARNING If you reach or lean it will affect the center of balance of your chair This may cause you to fall or tip over When in doubt ask for help or use a device to extend your reach I NEVER reach or lean if you must shift your weight sideways or rise up off the seat 2 NEVER reach o
36. lts f Replace safety cotter and caster housing cover g Repeat process for the other caster Inside Mounted a Reverse positions of caster assemblies b Remove caster assemblies from frame noting right positioned caster and left positioned caster 6 Inside mount right caster on the left side d Inside mount the left caster on the right side 930301 Rev D 38 Right Side Frame Left Side Frame X SET UP amp ADJUSTMENT O ANTI TIP TUBES OPTIONAL Quickie Designs recommends anti tip tubes for all wheelchairs Use a torque setting of 100 in Ibs when setting up the anti tip tubes Inserting Anti Tip Tubes Into Receiver a Press the rear anti tip release lever on the anti tip tube so that both release pins are drawn inside b Insert into the anti tip tube receiver c Turn the anti tip tube down until release pin is through the receiver mounting hole d Insert second anti tip tube the same way Adjusting Anti Tip Receiver a Remove anti tip tubes from anti tip receivers b Remove button head bolt from anti tip tube receiver c Reposition bracket to desired height d Reinsert button head bolt and tighten e Repeat with second anti tip tube receiver Both brackets should be at exactly the same height f Press the rear anti tip release lever on the anti tip tube so that both release pins are drawn inside g Insert it into the anti ti
37. nt a To raise legrest lift to desired position Legrest will automatically lock in place b To lower while seated in chair press release lever forward and lower legrest to desired position Legrest will automatically lock in place Articulating Legrest Elevating Legrest 930301 Rev D X SET UP amp ADJUSTMENT L CASTER FORKS Two hole caster forks allow interchanging 5 and 6 casters and adjusting seat height Caster Fork Adjustment a Loosen the bolt and remove the caster b Either change caster size and or position caster upward or downward in predrilled holes 1 inch apart on caster fork c Replace bolt and tighten securely M CASTER PLATES Angle Adjustment a Loosen the two eccentric bolts that secure the caster assembly Do not remove the clevis pin b Place a large right triangle against the table surface and the front surface of the caster bearing housing This will align the caster stem rotational axis perpendicular to the floor surface c When alignment is satisfactory retighten the two eccentric bolts d Repeat the process for the other caster N CASTER MOUNTING 2 Forward or Rearward Placement a Remove caster housing covers b Loosen the two eccentric bolts c Remove safety cotter and clevis pin d Slide caster plate forward or rearward and insert clevis pin into one of three pre drilled frame holes e Tighten the eccentric bo
38. on this chair are special high strength fasteners Use of improper fasteners may cause your chair to fail I ONLY use fasteners provided by an authorized supplier or ones of the same type and strength as indicated by the markings on the heads 2 Over or under tightened fasteners may fail or cause damage to chair parts 3 If bolts or screws become loose tighten them as soon as you can lf you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others E FOOTRESTS A WARNING I At the lowest point footrests should be AT LEAST 2 1 2 INCHES off the ground If set too LOW they may hang up on obstacles you can expect to find in normal use This may cause the chair to stop suddenly and tip forward 2 To Avoid A Trip Or Fall When You Transfer a Make sure your feet do not hang up or get caught in the space between the footrests b Avoid putting weight on the footrests as the chair may tip forward 3 NEVER lift this chair by the footrests Footrests detach and will not bear the weight of this chair Lift this chair only by non detachable parts of the main frame If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the ride
39. or loss of control may occur and cause severe injury to the rider or others 27 930301 Rev D VIII WARNINGS COMPONENTS amp OPTIONS J QUICK RELEASE AXLES A WARNING I Do not use this chair UNLESS you are sure that both guick release rear axles are locked An unlocked axle may come off during use and cause a fall 2 An axle is not locked until the guick release button pops out fully An unlocked axle may come off during use resulting in a fall tip over or loss of control and cause severe injury to the rider or others Quick Release Axles should be inspected for function and any signs of wear or bending Replace as necessary WARNING Routinely Inspect Replace if worn or bent If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others K REAR WHEELS A WARNING A change in set up of the rear wheels will affect the center of balance of your chair I The farther you move the rear axles FORWARD the more likely it is that your chair will tip over backward 2 Consult your doctor nurse or therapist to find the best rear axle set up for your chair Do not change the set up UNLESS you are sure you are not at risk to tip over 3 Adjust the rear wheel locks after you make any change to the rear axles a If you fail to do so the locks may not work b Make sure lock arms embed in tires at least 1 8 inch when locked If y
40. ou fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others L REAR WHEEL LOCKS A WARNING Rear wheel locks are NOT designed to slow or stop a moving wheelchair Use the only to keep the rear wheels from rolling when your chair is at a complete stop I NEVER use rear wheel locks to try to slow or stop your chair when it is moving Doing so may cause you to veer out of control 2 To keep the rear wheels from rolling always set both rear wheel locks when you transfer to or from your chair 3 Low pressure in a rear tire may cause the wheel lock on that side to slip and may allow the wheel to turn when you do not expect it 4 Make sure lock arms embed in tires at least 3 8 inch when locked If you fail to do so the locks may not work If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 28 VIII WARNINGS COMPONENTS amp OPTIONS M MODIFIED SEAT SYSTEMS A WARNING Use of a seat system not approved by Sunrise may alter the center of balance of this chair This may cause the chair to tip over I Do not change the seat system of your chair UNLESS you consult your authorized supplier first 2 Use ofa seat system not approved by Sunrise may affect the folding mechanism of this chair 3 Use ofa seating system not provided by
41. p tube receiver h Turn the anti tip tube down until release pin is through the receiver mounting hole i Insert second anti tip tube the same way Adjusting Anti Tip Tube Wheel The anti tip tube wheels may have to be raised or lowered to achieve proper clearance 1 2 to 2 a Press the anti tip wheel release button so that both release pins are drawn inside b Raise or lower to one of the three predrilled holes c Release button d Adjust the second anti tip tube wheel the same way Both wheels should be at exactly the same height 930301 Rev D P 2 3 X SET UP amp ADJUSTMENT CHECK OUT After the wheelchair is assembled and adjusted it should roll smoothly and easily All accessories should also perform smoothly If you have any problems follow these procedures Review the set up and check out section and operating guide to make sure chair was properly prepared Review troubleshooting guide If your problem persists contact your authorized supplier If you still have a problem after contacting your autho rized supplier contact Sunrise cus tomer service See the introduction page for details on how to contact your authorized supplier or Sunrise customer service 930301 Rev D 40 XI TROUBLESHOOTING You will need to adjust your chair from time to time for best performance especially if you alter the original settings This chart gives you a first solution
42. r lean if you must move forward in your seat to do so Always keep your buttocks in contact with the backrest 3 NEVER reach with both hands you may not be able to catch yourself to prevent a fall if the chair tips 4 NEVER reach or lean to the rear unless your chair has anti tip tubes locked in place 5 DO NOT reach or lean over the top of the seat back This may damage one or both backrest tubes and cause you to fall 6 IfYou Must Reach Or Lean a Do not lock the rear wheels This creates a tip point and makes a fall or tip over more likely b Do not put pressure on the footrests Note Leaning forward puts pressure on the footrests and may cause the chair to tip if you lean too far c Move your chair as close as you can to the object you wish to reach d Do not try to pick up an object from the floor by reaching down between your knees You are less likely to tip if you reach to the side of your chair e Rotate the front casters until they are as far forward as possible This makes the chair more stable Note To do this Move your chair past the object you want to reach then back up alongside it Backing up will rotate the casters forward f Firmly grasp a rear wheel or an armrest with one hand This will help to prevent a fall if the chair tips If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others F MOVING BACKWARD A WARNING Use e
43. r or others F PNEUMATIC TIRES A WARNING Proper inflation extends the life of your tires and makes your chair easier to use I Do not use this chair if any of the tires is under or over inflated Check weekly for proper inflation level as listed on the tire sidewall 2 Low pressure in a rear tire may cause the wheel lock on that side to slip and allow the wheel to turn when you do not expect it 3 Low pressure in any of the tires may cause the chair to veer to one side and result in a loss of control 4 Over inflated tires may burst If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 26 VIII WARNINGS COMPONENTS amp OPTIONS G POSITIONING BELTS OPTIONAL A WARNING Use positioning belts ONLY to help support the rider s posture Improper use of these belts may cause severe injury to or death of the rider I Make sure the rider does not slide down in the wheelchair seat If this occurs the rider may suffer chest compression or suffocate due to pressure from the belts 2 The belts must be snug but must not be so tight that they interfere with breathing You should be able to slide your open hand flat between the belt and the rider 3 A pelvic wedge or a similar device can help keep the rider from sliding down in the seat Consult with the rider s doctor nurse or therapist to find out if the ri
44. rims 3 4 longer fork stem bolt Armrests Option Padded swing away height adjustable Axle Plates Standard GP Option Double slot Axles Standard Stainless steel Option Titanium 930301 Rev D o Standard Rear Wheels Standard Spoke Option Mag Quickie Performance Wheels Option Tennis basketball heat treated tennis heat treated basketball Tire Size Standard 24 Option 22 26 Tire Types Standard Pneumatic Option Full profile polyurethane 22 24 only airless insert 22 24 only low profile polyurethane 24 only Kevlar 24 only high pressure clinch ers 24 26 only latex tubular 24 26 only turbo smooth 26 only turbo tread 24 26 only Handrims Standard Aluminum Option Plastic coated long tabs Projections Option Vertical oblique 6 8 10 12 Wheel Locks Standard Low mount All features may not be available with some chair setups or in conjunction with another chair feature Please consult your authorized supplier for more information 111 TABLE OF CONTENTS VI VII VIII INTRODUCTION ttt itor tetti a Sunrise Listens ncn kni YOUR CHAIR AND ITS PARTS TABLE OF CONTENTS NOTICE READ BEFORE USE 75a ll a Choose the Right Chair amp Safety 1 b Review This Manual Often eerte eM Clu ae 1 GENERAL
45. sary to re adjust the axle sleeves 930301 Rev D 34 m s CAMBER WASHERS PIA X SET UP amp ADJUSTMENT 4 Seat Height Adjustment a Remove axle plate bolts b Move the axle plate vertically in the predrilled frame holes to the desired position c Reinsert bolts in frame and tighten d Repeat on the other side of chair Adjustment must be exactly the same on both sides of the chair Note A front caster adjustment should be made to correspond with any change in seat height Rear Wheel Axle Nut Adjustment Tight axle sleeves should be maintained for proper performance of the wheelchair a To adjust the axle you will need a 3 4 wrench to turn the outside axle nuts b You will also need a 1 2 wrench to lodge the ball bearings on the opposite end of the axle and prevent the axle from turning c Turn the outside axle nut counter clockwise to tighten d There should only be zero to ten thousandths of an inch 010 of play WHEEL LOCKS Wheel locks are installed at the factory unless you have requested otherwise Use a torque setting of 100 in lbs when setting up wheel locks High Mount Scissor Wheel Locks a Loosen the screws on the top of each clamp b Slide assembly toward rear wheel until clamp embeds into tire to prevent wheel movement when in locked position c Adjust angle position d Tighten screws Low Mount Wheel Locks a Loosen the s
46. stallation or repair c Products modified without Sunrise Medicals express written consent d Damage from exceeding the weight limit 2 This warranty is VOID if the original chair serial number tag is removed or altered 3 This warranty applies in the USA only Check with your supplier to find out if international warranties apply 4 This warranty is not transferable and only applies to the first consumer purchase of this wheelchair through an authorized Sunrise Medical dealer D WHAT WE WILL DO Our sole liability is to repair or replace covered parts This is the exclusive reme dy for consequential damages E WHAT YOU MUST DO I Obtain from us while this warranty is in effect prior approval for return or repair of covered parts 2 Return the wheelchair or part s freight pre paid to Sunrise Mobility Products Division at 2842 Business Park Avenue Fresno CA 93727 1328 3 Pay the cost of labor to repair remove or install parts F NOTICE TO CONSUMER I If allowed by law this warranty is in place of any other warranty written or oral express or implied including a warranty of merchantability or fit ness for a particular purpose 2 This warranty gives you certain legal rights You may also have other rights that vary from state to state Record your serial number here for future reference 930301 Rev D 44 930301 Rev D 930301 Rev D 930301 Rev D SUNRISE MEDICAL Sunrise Me
47. trol may occur and cause severe injury to the rider or others 23 930301 Rev D VII WARNINGS FOR SAFE USE F MAINTENANCE A WARNING I Inspect and maintain this chair strictly per chart 3 At least once a year have a complete inspection safety check and service of your chair made by an authorized supplier If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others For additional maintenance information see Section XII Maintenance 930301 Rev D 24 2 If you detect a problem make sure to service or repair the chair before use A VIII WARNINGS COMPONENTS amp OPTIONS A ANTI TIP TUBES OPTIONAL A WARNING Anti tip tubes can help keep your chair from tipping over backward in most normal conditions I Sunrise Recommends Use Of Anti Tip Tubes a UNLESS you are a skilled rider of this chair and are sure you are not at risk to tip over b Each time you modify or adjust your chair The change may make it easier to tip backward Use anti tip tubes until you adapt to the change and are sure you are not at risk to tip over 2 When locked in place in the down position anti tip tubes should be BETWEEN 1 1 2 to 2 inches off the ground a If set too HIGH they may not prevent a tip over b If set too LOW they may hang up on obstacles you can expect in normal use If this occurs you may fall or your cha
48. xtra care when you move your chair backward Your chair is most stable when you propel yourself forward You may lose control or tip over if one of the rear wheels hits an object and stops rolling I Propel your chair slowly and smoothly 2 If your chair has anti tip tubes make sure to lock them in place 3 Stop often and check to be sure your path is clear If you fail to heed these warnings damage to your chair a fall tip over or loss of control may occur and cause severe injury to the rider or others 930301 Rev D 18 VI WARNINGS FALLS 8 TIP OVERS G RAMPS SLOPES 8 SIDE HILLS A WARNING Riding on a slope which includes a ramp or side hill will change the center of balance of your chair Your chair is less stable when it is at an angle Anti tip tubes may not prevent a fall or tip over I Do not use your chair on a slope steeper than 10 A 10 slope means one foot in elevation for every ten feet of slope length 2 Always go as straight up and as straight down as you can Do not cut the corner on a slope or ramp 3 Do not turn or change direction on a slope 4 Always stay in the CENTER of the ramp Make sure ramp is wide enough that you are not at risk that a wheel may fall over the edge 5 Do not stop on a steep slope If you stop you may lose control of your chair 6 NEVER use rear wheel locks to try to slow or stop your chair This is likely to cause your chair to veer out of control 7 Beware Of a
Download Pdf Manuals
Related Search