Home

Roll-Up III 1 - GTCO CalComp

1. Is the application program set for the digitizer Are computer communication Reconfigure the program parameters baud rate parity stop and or the computer bits data bits COM port set properly Does digitizer communicate now Yes one With Superset Menu Ba 1 Fade with Confiauration Menu the digitizer ja Find the SuperSet Code for the Configure digitizer per settings application program in Table 1 in application programs manual Enter code on SuperSet Menu Save setting in SuperSet storage locations 90 98 if desired Does diaitizer communicate now Go to Frocedure C 14557 N Band St u 266 746 3015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax Roll Up III 38 2 Comp by TURNING technologies _ TURNING technologies Using the Tablet Configuration Utilities IF your application is not represented in the SuperSet Menu and does not have a SuperSet Code or if a different configuration is required you can use the Tablet Configuration Utilities to configure Roll Up Ill The Tablet Configuration Utilities replace the 24 switches that were associated with older GTCO CalComp by Turning Technologies digitizers and the Custom Configuration Menu Card used with the Roll Up Il To configure the Roll Up III with the Tablet Configuration Utilities 1 Make sure the Roll Up III is plugged into a Serial Port powered on and all the tablet drivers have been uninstalled or disabled 2
2. Install the Tablet Configuration Utilities from the Se ect Utility Software to Install section on the TabletWorks CD or download them from www gtcocalcomp com 3 After the installation has completed run the Tablet Configuration Utilities from the Programs list under GTCO CalComp by Turning Technologies TCU 4 The Tablet Configuration Utilities will begin searching the Serial Ports for a Supported tablet a If the tablet is found information about the tablet will display under Device Info near the bottom of the screen b Ifthe tablet is not found a message will appear under Device Info near the bottom of the screen i If Wintab files were found it s possible that the TabletWorks driver has the Serial Port open li If the Serial Port is open by another application it will not be displayed under System Info Close any application or uninstall any driver that is using the Serial Port and select Refresh System Info from the File dropdown list at the top of the screen Click on the Serial Port icon under System Info to search that Serial Port NOTE The Tablet Configuration Utilities can use the TabletWorks driver to test the tablet but it must be communicating directly with the tablet via the Serial Port in order to configure it 5 Once the Roll Up Ill has been located on a Serial Port select Advanced Configuration from the Options dropdown list at the top of the screen a If Advanced Configuration is not an option make sure Wintab
3. AZ 35260 866 746 3015 toll free www gtoocalcomp com 490 9981751 fax PN 4 Roll Up III 18 CalComp by TURNING technologies Superset Program Company Code Mach Lite Ziatek Inc 04 Mach 2 Ziatek Inc 04 Mach 4 Ziatek Inc 83 MapGrafix Comeratix Inc 02 Market America CACI 11 MasterBuilder DOS Intuit 86 MasterBuilder 2003 2004 Intuit 01 Master Touch Integrated Measurement Systems 35 Measure Mate Measure Mate Australia 01 Measuremate Measuring Calc Paladin Measuring Systems 64 Measure Master Estimators Corner 51 Mechanical Construction Manager Mechanical Professional Services 73 Melco Melco 78 Metricom ADI Dynalog 71 Micromine Micromine Pty Ltd 27 Microstation PC Intergraph Corp 09 MIKE DOS Comput Ability Inc 63 MIKE Comput Ability Inc 42 Mirage Zenographics 36 Molitors amp Zimmer Molitors amp Zimmer Estimating Syst 67 NCE Estimator 2000 National Computer Est Inc 01 On Screen Take Off OnCenter Software 01 14557 N Band St Scottsdale AZ 35260 866 746 3015 toll free wWWwwW gtcocalcomp com 490 9981751 fax Roll Up III 19 a 4 CalComp by TURNING technologies Superset Program Company Code Pagemaker Aldus Corp 02 PAD ModaCAD 50 Paydirt Cross Section DOS Spectra Physics Laserplan Inc 31 Paydirt Roadwork DOS Spectra Physics Laserplan Inc 31 Paydirt Sitework DOS Spectra Physics Laserplan Inc 31 Paydirt Sitework Basic DOS Spectra Physics Laserplan Inc 31 Paydirt
4. Compatible Driver is not listed under Device Info 14557 N Band St SF a ee nun 866 746 5015 toll free Scottsdale AF 25260 wiv gTCOCaIcomp com 400 998175 fax Roll Up III 39 2 Comp by TURNING technologies _ TURNING technologies 6 Select a predefined 01 through 55 SuperSet Code or select one of the User Defined 90 through 98 SuperSet Codes to customize a User Defined 90 through 98 SuperSet Codes are initially read from the tablet when the Advanced Configuration screen opens This is to prevent loss of custom settings Selecting Read Current Settings from the Options menu will i Read the Power Up settings and User Defined SuperSet Codes from the tablet ii Overwrite all Custom Settings not yet saved to the tablet b Restore Factory Settings from the Options menu will prompt for i Power Up settings reset to factory default and set current ii User Defined SuperSet Codes cleared and reset to factory default 7 After making your selections choose one of the following from the File menu at the top of the screen a Save Temporary Settings will configure the tablet as shown until the tablet is powered off reset or another SuperSet Code is selected i After saving temporary settings select File Exit to test with other applications This will leave the tablet configured to the temporary settings selected and close the Serial Port enabling other applications to communicate with the tablet b Save Power Up Setting
5. Sitework 3 01 tor Windows Spectra Physics Laserplan Inc 05 Paydirt Sitework 3 2 for Windows Spectra Physics Laserplan Inc 01 Paydirt Trimble Navigation 01 P CAD Personal CAD Systems Inc 20 PC BAT 46 PC Paintbrush Z Soft 10 PC Paintbrush Windows Soft 02 PC3D Jandel Scientific 24 PDS SHADOW Polygon Software amp Technologies 53 PGO1I Hirsch International 22 Phoenix Estimator Phoenix Estimating a7 Picturemaker Cubicomp Corp 15 Piping DWY Estimating Fsscomate 32 Polynest Polygon Sottware 40 Power Takeott Ziatek Inc 04 Precision Estimating Disitizer DOS Timberline Software 37 Precision Estimating Disitizer Timberline Software 01 ProBid Promation 06 Procad Teksoft 13 Prodesign Il American Small Bus Comp Inc 01 14557 N Band St 866 746 3015 toll free Scottsdale AZ 28260 www gtcocalcomp com 480 998 1751 fax a 4 Roll Up III 20 CalComp by TURNING technologies Superset Program Company Code ProEst Estimating Digitizer Takeoff CMS 04 ProExcel Excel 80 Protessional Estimating Enterprise Computer Systems Inc 01 PTO CDCI 58 QED Roctek Corp 64 Quest Earthwork Quest Solutions 01 Quest Estimator Quest Solutions 01 QuickBid OnCenter Software 01 QuickCalc Constructive Computing 58 QuickCALC Windows Constructive Computing 01 QuickDirt Constructive Computing 23 QuickDirt Windows Constructive Computing 01 QuickDirt I QuickEst III Constructive Computing 58 QuickEst Constructive Computing 43 QuickEst Windows C
6. be exposed Do not roll the Roll Up Ill too tightly Rolling too tightly could damage the electronic grid 3 Insert the rolled digitizer into the shipping tube and allow it to fully unroll against the inside of the tube Place the factory supplied insert into the center of the rolled digitizer for support 4 Place the accessories in the accessory case and put it inside the hollow insert Set the factory supplied end caps on the tube to seal it Place the tube in the optional Deluxe Travel Bag NOTE The Deluxe Travel Bag is intended to be used only in conjunction with the factory supplied heavy gauge cardboard tube insert and end caps The Deluxe Travel Bag does not provide complete protection if used alone The product will be subject to damage not covered by the warranty if not protected by the tube insert and end caps 14557 N Band St SF a ee nun 256 746 3015 toll free Scottsdale A 25260 wie GTCOCaICOMp comM 400 998175 fax Roll Up III 35 2 Comp by TURNING technologies _ TURNING technologies If you have misplaced or disposed of these items contact GTCO CalComp by Turning Technologies 1 866 746 3015 for replacement parts Troubleshooting Guide As with any computer peripheral Roll Up III problems sometimes do occur Most of these problems are easy to find and correct This troubleshooting guide provides clear instructions for finding and solving all common digitizer problems In most cases you will be able to qui
7. on S for Select Mode NOTE Units built before October 8 2014 have serial Plug N Play enabled for SuperSet Code SJLo EB On these units use EJE 9 instead of S L0 1 This SuperSet Code has the same settings but Plug N Play is disabled Changing the Digitizer s Orientation Roll Up III lets you choose between two different digitizer orientations you can orient the digitizer with the controller Housing on your right the factory default or you can orient it with the Housing on your left To change the orientation of the digitizer 1 Turn the digitizer to the desired orientation 2 Relocate the origin by clicking on the L button on the SuperSet Menu that is located in the lower left corner of the digitizer You will hear four short tones when you do this NOTE The orientation of the 20 x 24 Roll Up III cannot be changed Turning the Alarm Off and On You can disable the alarm if you do not want to hear a tone each time the transducer button is pressed When the alarm is off you will still hear diagnostic and menu related tones To turn the alarm off or on e Click on the Lo button which toggles the tones on or off on the SuperSet Menu 14557 N Band St EEE TEEN E SEREE 866 746 3015 toll free Scottsdale AZ 25260 WWW GTCOCAICOMP COM 480 998 1751 fax Roll Up III 11 2 Comp by TURNING technologies _ TURNING technologies NOTE The following is relevant only for RS 232 serial installations USB does
8. to receive specific detailed custom configuration information from the Custom Configuration Menu for some serial installations In addition the SuperSet Menu can be used for both serial and USB connection configurations to set and change the digitizer orientation and to turn the digitizer alarm off and on Use your stylus or cursor to click on the menu buttons to make your selections The menu button initiates Select Mode Two digit numeric codes are entered after Select Mode is activated Most software supports Wintab using the TabletWorks drivers whose SuperSet Code is 1 on the SuperSet Menu The Roll Up III comes from the factory with the SuperSet Code 1 pre configured NOTE Select Mode will not work with the USB interface USB talks to Wintab drivers exclusively 14557 N Band St i 266 746 3015 toll free Scottsdale AZ 25260 www gticocaicomp com 480 998 1751 fax Roll Up III 10 2 Comp by TURNING technologies _ TURNING technologies The tL menu button sets your preferred digitizer orientation The Lo button toggles the digitizer alarm off and on The P button activates the Custom Configuration menu When using the SuperSet Menu a tone will sound indicating a successful selection when you click on the S or P buttons Four tones will sound when you click on 0 orl See the Roll Up Ill Tones section for a complete table of the Roll Up III tones The number buttons 0 through 9 are active only after clicking
9. 0 b mm 100 Ipmm or 150 Ipmm See the Advanced Programming Information section in the Super L VI Online Help at www gtcocalcomp com for more details Using the Custom Configuration Menu If your application is not represented in the SuperSet Menu and does not have a SuperSet Code or if a different configuration is required you can use the Custom Configuration Menu to configure Roll Up Ill The Custom Configuration Menu pictured below is stored in the slot at the end of the Roll Up Ill housing The Custom Configuration Menu replaces the 24 switches that were associated with older GTCO CalComp by Turning Technologies digitizers Communication Options Output Format Options Mode Options Baud Data Bits GTCO CalComp summa Mode Resolution Binary ASCH Button ASCII 2 ASCII 2 ASCII 3 Decimal ASCII 4 Include Exclude Space Line Feed Include Include Se Exclude Exclude Include Exclude Custom Configuration Menu Alignment Points 14557 N B2nd St 266 746 3015 toll free Scottsdale AZ 25260 www gtcocalcomp com 480 998 1751 fax Roll Up III 32 2 Comp by TURNING technologies _ TURNING technologies The configurations you set up can be stored for recall at a later time in any of the nine user definable SuperSet Menu locations codes 90 through 98 This allows the Roll Up III configuration to be easily switched between applications when you have such a requirement To configure the Roll Up Ill using the Cu
10. 1 TakeottTool US Cost 01 Terra Model DOS Plus 3 Software 09 Terramodel Trimble Navigation 01 Terrasoft Disital Resource Systems 01 Topographics IID CEIA Inc 5 Tops II Digitizer Sottware Shop Systems 28 TOSCA Clark University 74 Tradesman Tradesman Software 01 Turbo Map CAD U S Softtech 01 Versacad Versacad Corp 01 Vision Bidtek 70 Visual Takeott Comput Ability Inc 42 Wall to Wall Estimator Ramco 11 WenDuct Takeoff Wendes Systems Inc 48 WenPipe Wendes Systems Inc 46 Wilcom Ltd Wilcom Ltd 76 Windows Microsoft 01 WinEst Pro amp WinEst Pro Plus WinEstimator Inc 11 WinEx amp WinEx Pro Roctek Corp 01 WinMeasure DeLoach Corporation 01 WinScale Roctek Corp 01 2D CAD West Coast Consultants 33 14557 N Band St Scottsdale AZ 35260 866 746 3015 toll free wiww dtcocaicomp com 490 9981751 fax Roll Up III 23 a 4 CalComp by TURNING technologies Table 2 Configuration Details for SuperSet Menu Codes NOTE Max 100 coordinates second lpi lines per inch Code 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 1 18 19 20 Commun 9600 N 3 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 6 2 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 1 9600 N 8 2 9600 7 1 9600 E 7 2 9600 E 7 2 9600 N 8 1 1200 N 8 1 lomm lines per millimeter Output Options ASCII Options GTCO Binary 1000 Ipi Cont Max GTC
11. 2 10 Ipmm Cont 100 Summa Binary 10 Ipmm Point Summa ASCII 1 10 Ipmm Cont 100 Summa Binary 10 lpmm Point Alarm Summa ASCII UIOF 40 Ipmm Point GTCO ASCII 1000 Ipi Point Max Alarm GTCO ASCII 1000 Ipi Cont Incr GTCO ASCII 1000 Ipi Point Summa ASCII UIOF 1000 Ipi Point Roll Up III 26 ASCII Options Pb CR LF Pb CR LF Pb Sp CR LF Pb Sp CR LF Pb Sp CR LF Pb CR Pb Sp CR LF CR LF Sp CR Pb Sp CR LF CR LF Pb Sp CR LF CR CR CR LF CR LF Decimal Pb Sp CR LF Pb Sp CR Pb LF Pb LF 14557 N Band St Scottsdale AZ 35260 Wwiww atcocaicomp com 266 746 3015 toll free 480 998 1751 fax Roll Up Ill 27 a A CalComp by TURNING technologies Code Commun Output Options ASCII Options 66 Special 87 Special 85 Special 89 Special 90 98 User configuration storage locations 99 9600 N 3 1 GTCO Binary 1000 lpi Cont Max 86 89 require special firmware to activate 14557 N 82nd St N 866 746 3015 toll free Scottsdale AZ 25260 www gtcocalcomp com 480 998 1751 fax Roll Up III Tones a Roll Up III 28 CalComp by TURNING technologies The Roll Up III produces an alarm in the form of audio tones to inform you of various events The table below describes the kinds of tones you might her while operating the digitizer Table 3 Roll Up Tones Length Short Short Short Short once per second Medium Medium Medium once p
12. 4 CalComp by TURNING technologies Superset Program Company Code Batisoft 46 Best Est Il Bird Construction Software 23 Bid Team Construction Data Control Inc 58 Bidpoint Vertigraph Inc 01 Bidworx for DOS Vertigraph Inc 31 Bidworx for Windows Vertigraph Inc 01 BP 340 Barudan America Inc ff BuildNet Homesphere 09 Buildsoft Homesphere 09 BuildWare 1SqFt 01 BVH Gregg Estimating BVH Gregg Incorporated 04 Cadkey low res Cadkey 18 Cadkey hish res Cadkey 25 Callidus Oak Leaf Software 81 Calrson Takeoff Carlson Software 01 Carpet Estimating Systems Ramco 54 Civilcad Bloomfield Computer Services 03 CMS Estimating Contractor Management Systems 29 CNG Survey CNG Survey 05 14557 N 82nd St 266 746 3015 toll free Scottsdale AZ 85260 www gtcocalcomp com 480 998 1751 fax a 4 Roll Up III 14 CalComp by TURNING technologies Superset Program Company Code Coastal Oceanographics 42 Cogo PC Plus Civilsott 01 COINS Estimating Shaker Computer amp Management 41 Composer Gold Building Systems Design 42 Computer Methods Est Computer Methods 45 Comaquest Pinnacle Technology 38 Conception 3D Serbi 22 Construction Link The Construction Link 04 Contour Plus Civilsoft 01 Cost Engineer The Cost Engineering Technologies 49 Counterpoint Counterpoint 04 CPS SP Radian Corp 34 Curve Digitizer West Coast Consultants 35 Cut amp Fill DOS Paydirt Systems Inc 31 Cut amp Fill Precision DOS Paydirt Timberline 42 14557 N Ban
13. 4557 N Band St St a a TEES 256 746 3015 toll free Scottsdale AZ 8260 wie GTCOCaICOMp comM 480 908 1751 Fan Roll Up III 41 a A CalComp by TURNING technologies urnini enig ies DECLARATION OF CONFORMITY According to ISOMEC 17050 1 and EN 17050 1 Declaration of Conformity 9 00051 Rev A Revision history Rev 00 Created document 06 15 2004 Dana Doubrava Rev A Assigned part number updated the formatting to match new modified letterhead and contact information for Turning Technologies 10 18 2013 Andrea Davidson Dot 57 00051 Rev A 14557 N Band St 266 746 3015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax Roll Up III 42 x 4 CalComp by TURNING technologies urni 5 DECLARATION OF CONFORMITY O BR According to ISOAEC 17050 1 and EN 17050 1 Manufacturers Name Turning Technologies LLC DBA GTCO CalComp Manufacturers HQ Address 255 West Federal Street Youngstown Ohio 44503 U S A European Address 26 36 rue Alfred Nobel 93600 Aulnay Sous Bois France Phone 33 1 58 31 1060 Fax 33 158311069 Declares that the product Product Name Roll up Il Digitizer Model Numbers RUD 20x24 RUD 30x36 and RUD 36x48 Product Options All Conforms to the following specifications FMC EN55022 1995 41 2000 A2 2003 Class B Device EN55024 1998 41 2000 A2 2003 Class B Device EN61000 3 2 Harmonic Curent Emissions EM81000 3 3 Voltage Fluctuatons and Flicker EN
14. 61000 4 2 Direct ESD Indirect ESD EN61000 4 3 Radiated EN61000 4 4 Electrical Fast Tan EN61000 4 5 Surge Immunity EN61000 4 6 Conducted RF EN61000 4 8 Magnetic Field EM81000 4 1 1 Voltage Dips and Interruptions USA FCC Part 156 Title 47 Class B Digital Device Australia New Zealand AS NZS CISPR 22 2002 Chinese National Standard Taiwan CNS 13438 May 1997 Class B Digital Device Japan VCCI V 1 93 11 V 2 97 04 V 3 97 04 V 4 97 R 1216 and C 1278 as Class B ITE Safety EN IEC 60950 1 2001 ULICSA 60950 1 CE Marking The product cames the E Mark indicating compliance according to 2004 108 EC C Tick Marking The product cames the C Tick Mark indicating compliance according to the Standard AS NZS CISPR 222002 Class B Radio Frequency Equipment FCCAC Compliance This device complies with Part 15 of the FCC Rules Class A and RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device The user is cautioned that changes or modifications to the device that are not approved by the manufacturer could void user s authority to operate the device RoHS R labeled products conform to Directive 2011 6NEU Directive 2002 95 EC These products are RoHS compliant European Union WEEE Directive The manufacture of this equipment required the extracti
15. O Binary 1000 lpi Cont Incr GTCO Binary 1000 Ipi Cont Max GTCO Binary 1000 lpi Point GTCO Binary 1000 lpi Cont 100 GTCO Binary 1000 lpi Point GTCO Binary 200 lpi Cont 100 GTCO Binary 1000 Ipi Cont 100 GTCO Binary 1000 lpi Cont 12 GTCO Binary 200 lpi Cont Max GTCO Binary 1000 Ipi Cont Max Alarm GTCO ASCII 1000 Ipi Point GTCO Binary 1000 Ipi Cont 12 GTCO Binary 200 lpi Cont 100 GTCO Binary 200 Ipi Cont 100 Pb Sp CR LF GTCO Binary 200 Ipi Point GTCO Binary 200 lpi Cont Max GTCO Binary 200 lpi Cont Max GTCO Binary 1000 Ipi Point GTCO Binary 1000 Ipi Cont 100 14557 N Band St Scottsdale AZ 35260 266 746 3015 toll free www atcocalcomp com 460 998 1751 fax Roll Up III 24 a A CalComp by TURNING technologies Code Commun Output Options ASCII Options 21 4600 N 6 1 GTCO Binary 40 lpmm Cont 12 22 4600 N 6 1 GTCO Binary 1000 lpi Cont Max 23 2400 N 3 1 GTCO Binary 1000 Ipi Cont 12 24 9600 N 82 GTCO Binary 1000 lpi Cont Max 25 9600 N 6 2 GTCO Binary 1000 lpi Cont Max 26 9600 N 8 2 GTCO Binary 200 Ipi Point 27 9600 N 8 1 GTCO ASCII 40 Ipmm Point Pb Sp LF 28 4800 0 7 2 GTCO ASCII 100 Ipi Point Sp CR LF 29 1200 0 7 2 GTCO ASCII 1000 Ipi Point Pb CR LF 30 1200 N 8 1 GTCO Binary 40 Ipmm Cont 12 31 9600 0 7 2 GTCO ASCII 1000 Ipi Point Pb CR LF 32 9600 E 7 2 GTCO ASCII 1000 Ipi Point Sp CR 33 2400 E 7 1 GTCO ASCII 100 Ipi Cont 12 P
16. REHER TFT IDEE RERHTERNTFBIE ENMELTUIEFTH COBRBPIVAPTLEY ay SERICMELT AAnNSE FBEBERBIEELTLED BU ETF DRBERAELTETELUBUEBU ELTFEL Bescheinigung des Herstellers Importeurs Heirmit wird bescheinigt dass der die das 3036R Geraet Typ Bezeichnung im Uebereinstimmung mit den Bestimmungen der Vfg 1046 1984 Amtsblattverfuegung Funk Entstort ist Der Deutschen Bundespost wurde das Inverkehrbringen dieses Geraetes angezeigt und die Berechtigung zur Ueberpruefung der Serie auf Einhaltung der Bestimmungen eingeraumt GTCO CalComp Inc Name des Herstellers Importeurs Dieses Geraet wurde einzeln sowohl als auch in einer Anlage die einen normalen Anwendungsfall nachbildet auf die Einhaltung der Funkentstoerbestimmungen geprueft Es ist jodoch moeglich dass die Funkentstoerbestimmungen unter unguenstigen Umstaenden bei anderen Geraetekombinationen nicht eingehalten werden Fuer die 14557 N Band St 266 746 3015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax Roll Up III 44 a A CalComp by TURNING technologies Einhaltung der Funk entstoerbestimmungen seiner gesamten Anlage in der dieses Geraet betrieben wird ist der Betrieber verantwortlich Einhaltung mit betreffenden Bestimmungen kommt darauf an dass geschirmte Ausfuhrungen gebraucht werden Fuer die beschaffung richtiger Ausfuhrungen ist der Betrieber verantwirtlich European Union Emission Directive This product is in confo
17. Roll Up III 1 4 CalComp by TURNING technologies ROLL UP HI USER S GUIDE THE PORTABLE LARGE FORMAT DIGITIZER 14557 N 82nd St 266 746 3015 toll free Scottsdale AZ 25260 wiww gtcocaicomp com 480 998 1751 fax Roll Up III 2 2 Comp by TURNING technologies _ TURNING technologies Table of Contents Introduction 4 Parts Checklist 5 What You Will Need to Use Roll Up III 5 Setting Up Your Roll Up III 5 Software Configuration 5 Configuring Non Wintab Applications 6 Installing the TabletWorks Driver 6 Hardware Configuration 6 USB Connection 7 RS 232 Serial Connection 8 Using the SuperSet Menu 9 Changing the Digitizer s Orientation 10 Turning the Alarm Off and On 10 Configuring Your Roll Up III for Specific Applications 11 Example Configuring for a Specific Application 11 Table 1 SuperSet Menu Codes for Selected Applications 12 Table 2 Configuration Details for SuperSet Menu Codes 23 Roll Up Ill Tones 28 Table 3 Roll Up III Tones 28 Introduction to the Custom Configuration Menu 29 Communication Options 29 Output Format Options 30 Mode Options 30 Using the Custom Configuration Menu 31 Care and Handling of Roll Up III 33 Transporting Roll Up III 34 Troubleshooting Guide 35 Procedure A Begin Troubleshooting 36 Procedure B Troubleshooting 37 The Tablet Configuration Utilities 38 Regulatory Statements and Warranty 40 Radio and Television Interference 40 Canada 40 Declaration of Conformity 41 Japan 43 Besch
18. anty 4 Packaging costs Customers should keep their boxes Warranty Service Procedures 1 To obtain service on your GTCO CalComp by Turning Technologies product contact the Technical Support Department to receive a Return Material Authorization Number RMA and shipping instructions by calling 1 866 746 3015 2 Ship the product to GTCO CalComp by Turning Technologies with the RMA marked clearly on the outside of the box Without a clearly marked RMA on the shipping box GTCO CalComp by Turning Technologies reserves the right to refuse the shipment 3 Although you must pay any shipping charges to ship the product to GTCO CalComp by Turning Technologies for warranty service GTCO CalComp by Turning Technologies will pay the return shipping charges for ground shipment Other shipping options are available at an additional fee 4 Whenever warranty service is required the original dated sales invoice or a copy must be presented as proof of warranty coverage and should be included in shipment of the product Please also include your name address telephone number fax number email address and a description of the problem 5 If GTCO CalComp by Turning Technologies determines that the unit is not defective within the terms of the warranty the consumer shall pay the cost of all freight charges as well as any repair charges Technical Support Web based Technical Support is available free of charge at www gtcocalcomp com where curren
19. ation vendor A driver does not need to be installed if you are using Roll Up III with GTCO CalComp by Turning Technologies QuikRuler III Configuring Non Wintab Applications Many application programs provide configuration information for specific digitizers If the Roll Up Ill digitizer is not listed you can use the configuration for GTCO CalComp by Turning Technologies Digi Pad Type 5 or Type 5A T5 T5A Roll Up II CalComp 9100 9500 or Summagraphics Microgrid III or ID Series Installing the TabletWorks Driver Insert the CD into the CD ROM drive on your computer The installer will autoload If it does not click on the Start button on the Windows Task Bar and select Run from the menu Type X setup exe X represents the CD drive letter Follow the onscreen prompts to complete the installation A TabletWorks icon Lh will display in the System Tray on the Windows Task Bar Right click on the icon to display the TabletWorks Menu which provides access to all the TabletWorks features Hardware Configuration When you use the USB interface no data output configuration is required However when you choose the optional serial interface the Roll Up III must be configured to send data ina format that is compatible with the application software Different applications have different requirements when interacting with a digitizer Roll Up III is designed to provide the appropriate serial requirements for a wide variety of graphic CAD and e
20. b Sp CR LF 34 9600 8 7 1 GTCO ASCII 1000 Ipi Point Pb Sp CR LF 35 9600 E 7 1 GTCO ASCII 1000 Ipi Point Pb Sp CR LF 36 9600 E 7 1 GTCO ASCII 1000 lpi Cont 12 Sp CR LF 37 2400 N 8 1 GTCO ASCII 1000 Ipi Point Pb Sp CR LF 38 2400 E 7 2 GTCO ASCII 1000 Ipi Point Pb Sp CR LF 39 1200 0 7 1 GTC ASCII 1000 Ipi Cont 12 Pb CR 40 1200 N 8 1 GTCO ASCII 1000 Ipi Point Pb Sp CR LF 14557 N Band St 266 746 3015 toll free Scottsdale AZ 28260 www gtcocalcomp com 480 998 1751 fax Code Commun 41 9600 E 7 1 42 9600 N 8 1 43 1200 E 7 1 44 9600 N 8 1 45 9600 N 8 2 46 9600 E 7 2 47 9600 0 7 2 48 9600 E 7 1 49 1200 E 7 1 50 9600 E 8 1 51 1200 N 7 2 52 9600 E 8 1 53 9600 N 8 1 54 9600 N 8 1 55 9600 0 7 2 56 9600 E 7 2 57 9600 0 7 1 58 9600 N 8 1 59 1200 E 7 1 60 9600 0 7 1 a A CalComp by TURNING technologies Output Options GTCO ASCII 1000 Ipi Point GTCO ASCII 1000 Ipi Point GTCO ASCII 1000 Ipi Point Alarm GTCO ASCII 1000 lpi Cont 12 Alarm GTCO ASCII 100 lpi Point Alarm GTCO Binary 1000 lpi Cont 100 GTCO ASCII 1000 Ipi Cont 100 GTCO ASCII 1000 lpi Point GTCO ASCII 1000 Ipi Cont 12 GTCO ASCII 40 lpmm Point Alarm GTCO ASCII 1000 lpi Point GTCO Binary 1000 Ipi Cont 100 Alarm GTCO ASCII 1000 Ipi Cont Max GTCO ASCII 1000 lpi Cont 12 GTCO ASCII 1000 lpi Cont Max Alarm GTCO ASCII 1000 lpi Point GTCO ASCII 1000 Ipi Point GTCO ASCII 1000
21. ckly take care of the problem yourself by following these steps 1 Install properly first This troubleshooting guide assumes you have already correctly installed Roll Up III according to the detailed instructions in the Setting Up Your Roll Up Ill section If you have not followed the step by step instructions in that section do so now 2 Work through the troubleshooting flowcharts on the following pages in this troubleshooting guide Record any unusual observations Your notes will be useful if you need assistance from GTCO CalComp by Turning Technologies 3 If your system still does not work Call our Technical Support Department at 1 866 746 3015 Be prepared to discuss the observations you made while troubleshooting A Technical Support Specialist will help you resolve the problem as quickly as possible NOTE Refer to the Roll Up III Tones table while using the Troubleshooting Guide If you are experiencing erratic behavior with your digitizer make sure that no conductive materials are being used This includes the graphite in pencil lead some black plotter ink and digitizing on plastic or Mylar No electronic devices should be sitting on or near the digitizer including keyboards mice calculators etc If any of these describes normal working conditions the Super L Series Digitizers would be more suited to your environment NOTE Tablet Not Found If you are using a USB connection and the digitizer is not found either di
22. cocalcomp com 14557 N Bind St u er 3 966 746 3015 toll free Scottsdale AZ 85760 WWww atcocaicomp com 480 998 1751 fax Roll Up III 45 a A CalComp by TURNING technologies Limited Warranty for Roll Up III GTCO CalComp by Turning Technologies Inc warrants these products to be free from defects in material and workmanship under the following terms Complete and return the enclosed warranty registration card to ensure that your products are covered with this warranty Coverage Parts and labor are warranted for two 2 years from the date of the first consumer purchase for the digitizer tablet controller transducers and tablet accessories Power supply and cables are also warranted for one 1 year This warranty applies to the original consumer purchaser only Within the European Union the warranty period is two 2 years as mandated by the EU Contact your local dealer or distributor for additional warranty information Warranty is only valid if original consumer s purchase or lease date is less than or equal to six months from the original GTCO CalComp by Turning Technologies sale date This information will be captured by the system serial number and confirmed by the reseller s purchase order A nominal Warranty Handling Fee will be charged after the first 90 days of use and calculated from the date of original consumer purchase This payment may be made by Visa MasterCard or American Express A copy of t
23. d St Scottsdale AZ 35260 866 746 3015 toll free wiww dtcocaicomp com 480 90081751 fax PN 4 Roll Up III 15 CalComp by TURNING technologies Superset Program Company Code Datacad Microtecture 14 DATAMINE Datamine International 62 Deed Mapping System US Soft Tech 13 DEEM Met Coil Lid 69 Design CAD American Small Business Computers 01 Designer Microgratix 02 DisiPlus Civilsott 01 DisiPro Prosoft 66 Disitool Roctek Corp 24 DigiWin Prosoft 68 DMS Premiere Tally Systems 57 DO 2000 DO Technologies Inc 85 DrawPlus Microgratix 02 Earth Graphics Deluxe Earth Graphics 01 Earthwork Civilsott 01 Earthwork 3D AGTEK Development Co 01 Earthwork Estimating Ground Rules 01 Earthworks Tally Systems Inc 01 Earthworks tor Windows Trakwear 01 OR Earthworks for Windows Trakwear 56 Easydij EJBIN 4 Geocomp Ltd 16 Easyvdij EJAF 2 Geocomp Ltd 35 Easydij EJBIN 30 Geocomp Ltd 19 Easy Cad Easy Cad 01 Eclare Prosoft Inc 66 Edge The DOS Advanced Estimating 01 14557 N Band St Scottsdale AZ 35260 866 746 3015 toll free wWWwwW gtcocalcomp com 480 398 1751 fax a 4 Roll Up III 16 CalComp by TURNING technologies Superset Program Company Code Edge The Advanced Estimating 01 Equinox Roctek Corp 64 ES 6000 Estimating System McCormick Systems 09 EST Duct Estimating Technical Sales International 01 EST Mechanical Technical Sales International 01 Estimagic Estimagic 63 Estimat All Sateharbor So
24. einigung des Herstellers Importeurs 43 14557 N 82nd St SF a ee EES 956 746 3015 toll free Scottsdale AZ 5760 Vi eV Ve cic OQ g Ol 13 L Ol 490 998 1751 fax Roll Up III 3 a 4 CalComp by TURNING technologies European Union Directives 44 Limited Warranty for the Roll Up III 45 14557 N 82nd St 266 746 3015 toll free Scottsdale AZ 25260 wiww gtcocaicomp com 480 998 1751 fax Roll Up III 4 2 Comp by TURNING technologies _ TURNING technologies Introduction Roll Up III belongs to a class of computer input devices called graphic tablets or digitizers A digitizer is an electronic tablet work surface The position of a transducer a handheld cursor or stylus on the work surface of the Roll Up III is converted digitized into data for computer processing Data output from the Roll Up III digitizer is in the form of an X Y coordinate pair that pinpoints the location of the transducer on the tablet surface The Roll Up Ill is a specialized graphic digitizer that is specifically designed to be portable so it can be taken to the job site NOTE Roll Up Ill uses an electrostatic technology for digitizing with blueprints and nonconductive inks If you are using black line drawings with conductive ink the Super L Series Digitizers are more appropriate Roll Up III works with many graphic CAD and estimating applications These applications use the digitized data from the Roll Up III to e Determine the dimensions o
25. eluxe travel bag connector for serial connection v Power supply required only for serial installations What You Will Need to Use Roll Up III e Acomputer running a Windows operating system with USB port or an RS 232C serial Communication port Serial signal levels must conform to EIA RS 232C specifications e Application software that accepts digitizer input via the Wintab API or application software that directly accepts digitizer input via the computer s RS 232C serial port Setting Up Your Roll Up III The instructions below describe how to set up your Roll Up Ill Before you begin please take a moment to fill out and mail the Warranty Registration Card or register your digitizer on our website at http www gtcocalcomp com warranty information Software Configuration Software drivers provide the communication bridge between your digitizing software application and the Roll Up Ill You should install only the drivers necessary for the Roll Up III to work with your application software The GTCO CalComp by Turning Technologies 14557 N Band St ENTER A PSP Lees 866 746 3015 toll free Scottsdale AZ 88260 wie GTCOCaICOMp comM 400 998175 fax Roll Up III 6 2 Comp by TURNING technologies _ TURNING technologies Supplied TabletWorks CD supports reduced functionality Wintab and TabCon compatible applications If you are not sure which drivers are required check the Table 7 section of this manual or consult with your applic
26. er second Short twice per second Long once per second tollowed by short Continuously on Short 1 16 second Number of times Four at power up Four Once Continuously Three Three at power up Continuously Continuously Eight long beeps tollowed by tour short At power up Medium 1 4 second Meaning Diagnostics passed Successtul end of menu mode Transducer switch pressed if the alarm tone is enabled Transducer not attached Menu mode aborted Configuration error Configuration Menu mode waiting tor Alignment Point 1 Configuration Menu mode waiting tor Alignment Point 2 Grid disconnected Diagnostics failed Long 1 2 second Configuration error tones or Diagnostics failed tones indicate a serious problem If you hear either of these tones call GTCO CalComp by Turning Technologies Technical Support at 1 866 746 3015 NOTE You might hear tones produced by the Roll Up III which are actually sent by your application program Programs can send commands to the digitizer to turn the audio tone generator on and off If you hear tones during digitizing and they do not correspond to the tones listed in the table above they are produced by the application program 14557 N Bend St Scottsdale AZ 85760 WWww atcocalcomp Com 266 746 3015 toll free 480 992 1751 fax Roll Up III 29 2 Comp by TURNING technologies _ TURNING technologies NOTE This information applie
27. er the Space Sp character hex 20 is included in the ASCII output report as a delimiter between the X and Y coordinate values This option is available only in GTCO formats Choices are Include or Exclude e Decimal Defines whether the period character hex 2E is included in the ASCII output report between the units and tenths digits This option is available only in Summagraphics formats Choices are Include or Exclude e Return Defines whether the Carriage Return CR character hex OD is included in the ASCII output report as a terminator This option is available in GTCO and Summagraphics formats Choices are Include or Exclude e Line Feed Defines whether the Line Feed LF character hex OA is included in the ASCII output report as a terminator This option is available in GTCO CalComp and Summagraphics formats Choices are Include or Exclude 14557 N Bond St SIE Le Pon ae a SS 266 746 3015 toll free Scottsdale AZ 88260 WwWww gticocalicomp com 400 998175 fax Roll Up III 31 A CalComp by TURNING technologies Mode Options e Mode Defines how output reports are sent from the digitizer Choices are Point Line Continuous Line Incremental or Continuous Incremental e Rate Determines how fast output reports will be transmitted from the digitizer Choices are 12 50 or 100 reports per second e Resolution The smallest reported value returned by the digitizer Choices are 1000 Ipi 2000 lpi 4000 Ipi 4
28. es indicating that the configuration is complete Roll Up III is now configured to operate with AutoCAD Select Mode is no longer active You can begin digitizing 14557 N Band St SF a ee nun 256 746 3015 toll free Scottsdale A 25260 wie GTCOCaICOMp comM 400 998175 fax a 4 CalComp by TURNING technologies Roll Up III 12 NOTE For more information about digitizer software application driver requirements please go to the Technical Support section of the GTCO CalComp by Turning Technologies website Table 1 SuperSet Menu Codes for Selected Applications Program ACCESS Advanced Construction Estim ANGE AGTEK Earthwork Engineering DOS APS ARC CAD ARC INFO DOS ARC INFO ARC GIS ARC View ARCT ACA ArenaSoft Estimating ATLAS DRAW low res ATLAS DRAW high res ATLAS GIS AutoCAD Autodesk 3D Studio AutoSketch Autoship Autoyacht Autumn 14557 N Band St Scottsdale AZ 35260 Company Bautech Sottware Shop Systems CEIA Inc AGTEK Development Co Gunold amp Stickma ESRI ESRI ESRI ESRI ESRI Arena Soft Strategic Locations Planning Strategic Locations Planning Strategic Mapping Autodesk Inc Autodesk Inc Autodesk Inc Coastdesign Coastdesign Zenographics www atcocaicomp com Superset Code 39 28 5 09 a2 01 12 01 01 01 4 01 07 05 01 01 01 01 01 01 36 866 746 3015 480 998 1751 toll free fax Roll Up III 13 a
29. f objects on drawings and blueprints e Move the pointer on the display screen e Create and manipulate objects in a graphic composition e Trace a drawing or other source material to create an image on the display screen e Select commands or functions from an application menu placed on the tablet Surface e Select items from a pull down menu on the display screen In order to send data from the Roll Up III to your digitizing application the digitizer must be physically connected to your computer and it must be able to transmit the data in sucha way that the digitizing application recognizes and understands it Before you set up the Roll Up III you should determine e The requirements of the digitizing software application being used e Whether your digitizing application requires software drivers to communicate with the Roll Up III e Hardware communications connection Serial or USB you will be using between the Roll Up III and the computer 14557 N Bond St SIE Le Pon ae a SS 266 746 3015 toll free Scottsdale AZ 88260 WwWww gticocalicomp com 400 998175 fax Roll Up III 5 2 Comp by TURNING technologies _ TURNING technologies Parts Checklist v Roll Up III digitizing tablet v CD ROM with Windows Drivers and v Transducer stylus pen 4 button or user s manual 16 button cursor v Accessory case v USB cable v Cardboard tube insert and end caps Do Not Discard Optional Equipment v Computer interface cable with 9 pin v D
30. ftware Inc 54 Estimate Software Estimate Software 04 Estimation Inc 700 Series Estimation Inc Tradepower 69 Estimation Inc 800 amp Win Series Estimation Inc Tradepower 86 Execucom Execucom Systems Corp 36 Expose Roctek Corp 64 Fastcad Evolution Computing 26 FastPIPE Gold FastEST Inc 01 Floor Rite RFMS 01 GAP 01 GTCO CalComp 39 Gemini Excel 79 Generic CADD Generic Software Inc 01 Geoquest Sottdesk 08 GM SY5 NW Geophysics Association Inc 13 GraphPlus Microgratix 02 GTCOTEST default GTCO CalComp 01 GTCO Wintab Driver GTCO CalComp 01 HALO products Media Cybermetics 13 Hotdij Geocomp Ltd 35 14557 N Band St Scottsdale AZ 35260 866 746 3015 toll free www atcocalcomp com 460 998 1751 fax a 4 Roll Up III 17 CalComp by TURNING technologies Superset Program Company Code IBM GFIS IBM 55 Ice System The DOS MC 56 ICE 2000 MC 01 IDRISI Clark University 74 IKE DOS Comput Ability Inc 72 IKE Comput Ability Inc 42 Imagine 5 X ERDAS Inc 61 Insite Earthwork Estimating Software Shop Systems 19 Insite 2 Software Shop Systems 28 Insite Sitework Insite Sottware 01 Insulcomp Technical Sales International 42 JAVA Jandel Scientitic 24 Job Boss Small Systems Design Inc 39 Job Power Job Power 4 Kolvin Pro Damon Inc 01 Landmarke Cambridge Software Inc 23 Lasercad The Software Machine 01 Logdigi Planimeter The Logic Group 12 Lumena T me Arts Inc 10 14557 N Band St Scottsdale
31. he sales receipt or invoice will be required for warranty verification Conditions Except as specified below this warranty covers all defects in material or workmanship in the products The following are not covered by the warranty 1 Any product on which the serial number has been defaced modified or removed if applicable 2 Damage deterioration or malfunction resulting from a Accident misuse abuse neglect fire water lightning or other acts of nature unauthorized modification for any purpose unauthorized product modification or failure to follow instructions supplied with the product b Repair or attempted repair by anyone not authorized by GTCO CalComp by Turning Technologies c Any damage in shipment of the product claims must be presented to the carrier d Any other cause which does not relate to a manufacturing defect 3 Any product not sold or leased to a consumer within six months of GTCO CALCOMP BY TURNING TECHNOLOGIES original sale date GTCO CalComp by Turning Technologies will pay all labor and material expenses for covered items but will not pay for the following 1 Removal or installation charges 14557 N Bind St u er 3 866 746 5015 toll free Roll Up III 46 a A Calcomp by TURNING technologies 2 Costs for initial technical adjustments set up including adjustment of user controls 3 Certain shipping charges Payment of shipping charges is discussed in the next section of this warr
32. lled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee the interference will not occur ina particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Reorient or coil cables e Consult the dealer or an experienced Radio TV technician for help NOTE Any cables the user adds to the device must be shielded to be in compliance with the FCC standards Any unauthorized modification to this device could result in the revocation of the end user s authority to operate this device Canada This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as Set out in the radio interference regulations of the Canadian Department of Communications Le present appareil num rique n emet pas bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par le Ministere des Communications du Canada 1
33. lpi Cont 12 GTCO ASCII 1000 lpi Point Alarm GTCO ASCII 1000 Ipi Point Alarm Roll Up III 25 ASCII Options Pb Sp CR Pb Sp CR LF Pb Sp CR Pb Sp CR LF Pb CR LF Pb CR CR LF Pb CR Pb Sp CR LF Pb CR LF Pb CR Pb CR Pb CR Pb Sp CR LF Pb Sp CR LF Pb CR LF Pb Sp CR Pb 14557 N Band St Scottsdale AZ 35260 www gtcocalcomp com 266 746 3015 toll free 480 998 1751 fax Code Commun 61 62 63 64 65 66 6 65 69 0 Al 2 73 f4 5 6 if Fii r79 ag l 62 63 64 65 4800 N 8 1 2400 N 8 1 1200 0 7 1 9600 N 8 1 2400 N 8 1 9600 0 7 2 9600 N 8 1 9600 0 7 2 9600 7 1 1200 N 8 1 9600 N 8 1 1200 0 7 2 9600 N 8 1 9600 N 8 9600 N 8 9600 N 8 1 9600 N 8 1 2400 N 8 1 9600 0 7 2 9600 0 8 1 9600 E 7 2 9600 N 8 9600 N 8 9600 N 8 1 9600 N 8 1 a A CalComp by TURNING technologies Output Options GTCO ASCII 1000 lpi Point GTCO ASCII 1000 lpi Cont 12 GTCO ASCII 1000 lpi Point GTCO ASCII 1000 lpi Point GTCO Binary 1000 lpi Cont 100 GTCO ASCII 1000 lpi Point GTCO ASCII 1000 lpi Cont 12 Alarm GTCO ASCII 100 Ipi Point GTCO ASCII 40 lpmm Point GTCO ASCII 100 lpi Point Max Alarm GTCO Binary 40 Ipmm Cont GTCO ASCII 100 Ipi Point GTCO ASCII 1000 lpi Point GTCO ASCII 1000 Ipi Cont 100 Alarm Calcomp ASCII 3 1000 Ipi Point Summa ASCII 2 10 Ipmm Point Summa ASCII
34. not require configuration Configuring Your Roll Up III for Specific Applications To configure your Roll Up IlI for use with specific applications 1 In Table 1 find the application program you will be using with your Roll Up Ill Note the corresponding SuperSet Code e If your application program is not listed in Table 1 find the configuration settings in Table 2 that your application program requires and use the corresponding SuperSet Code e If an appropriate SuperSet Code is not listed in Table 2 then use the Custom Configuration Menu see the Using the Custom Configuration Menu section to Set up your Roll Up Ill 2 Onthe SuperSet Menu click on the S button then click on the two digits of the SuperSet Code indicated for your application You will hear four short tones after a successful menu configuration Example Configuring for a Specific Application Suppose you wanted to configure your Roll Up III to operate with Autodesk s AutoCAD application You would 1 Find the entry for AutoCAD in Table 1 The SuperSet Code is 01 2 Click on the S button on the SuperSet Menu You will hear one short tone indicating the digitizer is in Select Mode 3 Select the 0 button on the SuperSet Menu You will hear one short tone This enters the first digit of the SuperSet Code for AutoCAD 4 Click on the ai button on the SuperSet Menu This enters the second digit of the SuperSet Code for AutoCAD You will hear four short ton
35. omissions that may appear in this document or for the use of this material Nor does GTCO CalComp by Turning Technologies make any commitment to update the information contained in this document This document contains proprietary information which is protected by copyright All rights reserved No part of this document can be photocopied or reproduced in any form without the prior written consent of GTCO CalComp by Turning Technologies Inc 14557 N Bind St a tect Se 866 746 5015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax
36. on and use of natural resources It may contain hazardous substances that could impact health and the environment In order to avoid the dissemination of the hazardous substances into the environment and to diminish the pressure on our natural resources we encourage you to return this product to the appropriate take back system facility These facilities reuse or recycle most of the materials in this equipment in a responsible way The crossed out wheeled bin symbol invites you to use these take back systems If you need more information about the collection reuse and recycling systems in your area please contact your local or regional waste authority Further information about the responsible end of life management of this and other products is available on our Web site at www TurningTechnologies com Below is a list of supporting documents to claim this DoC Report Number GTEOIEMC147 8 ACA GTCOVMC14 76 FCC GTCOWMC14 76 CISPR24 GTCOVWEMC14776 VCC amp GTCOVEMC14778 B3SMl of December 20 2004 Testing Facility MET Laboratories Inc 914 West Patapsco Ave Baltimore MD 21230 Jeff Cunningham Youngstown Ohio U S A 10 18 13 Director of Hardware R amp D Location Date Dot 57 00051 Rev A 14557 N Band St aa 866 746 3015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax Roll Up III 43 PN 4 CalComp by TURNING technologies Japan ORES ERUEZEFERBEFRE EHE BER SS VCCI DEE CEI lt ISFSAZBER
37. onstructive Computing 01 QuickMeasure Tally Systems Inc 01 QuickPen AutoBid QuickPen International 04 QuickPen CAD QuickPen International 09 QuickPen Estimating QuickPen International 59 QuoteExpress Quote Software 01 14557 N 82nd St 866 746 3015 toll free Scottsdale AZ 25260 www gtcocalcomp com 480 998 1751 fax Program Ramco Estimating System Remodeling Estimator Right Hand Man Roadeng Robocad Robosolid Rockit Root Cad Root Estimator 3000 SDP Sheetmetal Ductwork SigmaPlot S gmascan SiteCalc Smartcam Softplan Sonnet CAD Sonnet Gap Subway Starbid Super Duct Super Pipe Surpac 14557 N Band St Scottsdale AZ 35260 a 4 www gtcocalcomp com Roll Up III 21 CalComp by TURNING technologies Superset Company Code Ramco 54 National Computer Estimating Inc 01 Johnston amp Associates Inc 04 Softree Technical Systems Inc 27 RoboSystems International 21 Ziatek 04 True North Estimating Systems 12 Essential Technology 65 Civilsott 01 Esscomate 32 Jandel Scientific 24 Jandel Scientific 24 Eagle Point 01 Point Control Co 17 Softdesk 08 Interworld Electronics 03 Interworld Electronics 20 Roctek Corp 64 Geac 29 Wendes Mechanical Consulting 48 Surpac Mining Systems 27 866 746 3015 480 998 1751 toll free fax a 4 Roll Up III 22 CalComp by TURNING technologies Superset Program Company Code Takeoff 2000 Comput Ability 42 Takeoff Pro WinEstimator Inc 0
38. or near the Roll Up III to avoid scratching or cutting it Cuts in the digitizer will void your warranty 1455 7 N Band St Scottsdale AZ 266 746 5015 toll free 25960 WwWww gticocalicomp com 400 998175 fax Roll Up III 34 2 Comp by TURNING technologies _ TURNING technologies e Do not crease dent or abuse the digitizer Creases can damage the digitizer Structure Severe creases or abuse will void your warranty e Clean Roll Up III with any mild nonabrasive household cleaner Rubbing alcohol is recommended Do not apply liquid directly to the surface of the Roll Up Ill Spray the cleaning solution on a cloth and wipe it over the surface After cleaning dry the Surface to avoid possible digitizing errors Transporting Roll Up IlI You MUST transport Roll Up III using the factory supplied shipping materials heavy gauge cardboard tube insert and end caps Failure to do so could result in serious damage to the unit and may void your warranty 1 Disconnect the transducer and interface cable from the Roll Up Ill and the computer Remove all material from the digitizer 2 Grasp the controller housing firmly with both hands and roll it toward the opposite side of the digitizer The housing and the printing on the digitizer surface must be on the inside of the roll The roll diameter should be just smaller than the inside diameter of the factory supplied shipping tube When correctly rolled only the digitizer s black back will
39. per settings have been selected Pass the transducer down each group of options the alarm will sound when the transducer is over the active choice Some groups may be inactive based on the options selected Click on a desired setting in a group to change it To cancel all settings click in the active area outside the menu 7 When you have finished making your selections you can save the configuration If you choose to save it temporarily the configuration will be remembered only until another SuperSet Code is entered If you never change the configuration of your Roll Up III from the custom one you just entered the temporary configuration will always be used However if you expect to be switching between configurations and 14557 N Bang St a Nd oe 266 746 5015 toll free Sc otts sedalo A 28260 Vi WV Ve cic OLA Ol IDE Ol 490 398 1751 fax Roll Up III 33 2 Comp by TURNING technologies _ TURNING technologies want to save the custom one for later recall you can assign the configuration to a special user definable SuperSet Code To save the configuration temporarily Click on the P button on the SuperSet Menu You will hear four short tones to indicate you successfully saved the custom configuration The configuration is saved in a temporary location where it will be retained even when the unit is powered off or reset However if another SuperSet Code is entered this temporary configuration is lost and cannot be recalled witho
40. red in the slot on the end of the Roll Up III housing to configure your Roll Up III 1 Plug the power supply into an AC outlet Connect the power supply to the appropriate jack on the Connector Panel The digitizer will beep four short tones see the Roll Up Ill Tones section for a complete table of Roll Up Ill tones indicating it is powered on 2 Connect the RS 232 serial cable to the serial jack on the Connector Panel The connector is keyed and will fit only the correct jack Do not force it 3 Configure the SuperSet Code The Roll Up Ill comes from the factory with the SuperSet Code SJ 0 pre configured See Using the SuperSet Menu 14557 N 82nd St 266 746 3015 toll free Scottsdale AZ 25260 www gtcocalcomp com 480 998 1751 fax Roll Up III 9 a 4 CalComp by TURNING technologies Serial Connection m Transducer Computer a Power aag z Tr a DD Serial i ki f A Using the SuperSet Menu The SuperSet Menu is the row of buttons printed in the lower left and upper right corners of the digitizer amp Jl sJlollit2 ls la ls le z 8 9 JP Uo The SuperSet Menu makes it possible to configure the Roll Up III so that it sends the appropriate information for a serial connection to the software being used on your computer see Table 7 section of this manual for an extensive list of digitizer software applications and their codes It is used to prepare the digitizer
41. rmity with the protection requirements of EU Council Directive 89 366 ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 European Standard EN55022 The limits for Class B equipment were derived for typical industrial environments to provide reasonable protection against interference with licensed communication devices European Union WEEE Directive The manufacture of this equipment required the extraction and use of natural resources It may contain hazardous substances that could impact health and the environment e In order to avoid the dissemination of the hazardous substances into the environment and to diminish the pressure on our natural resources GTCO CalComp by Turning Technologies encourages you to return this product to the appropriate take back system facility These facilities reuse or recycle most of the materials in this equipment in a responsible way e The crossed out wheeled bin symbol below invites you to use these take back systems e Ifyou need more information about the collection reuse and recycling systems in your area please contact your local or regional waste authority e Further information about the responsible end of life management of this and other GTCO CalComp by Turning Technologies products is available on our website at www gt
42. rranty gives you specific legal rights and you may have other rights which vary from state to state or province to province To obtain service on your GTCO CalComp by Turning Technologies product call our Technical Support Department at 1 866 746 3015 or fax us at 480 998 1751 We can also be contacted through our website at www gtcocalcomp com in US at EUOffice gtcocalcomp com in Germany at infos calcomp fr in France Important All products returned to GTCO CalComp by Turning Technologies for service must have prior approval in the form of a Return Merchandise Authorization Number RMA which can be obtained by calling the Technical Support Department 14557 N Band St aa a a i 266 746 3015 toll free Scottsdale AZ 25760 Vw WV Vi gtc OC a Co 152 L ol 490 998 1751 fax Roll Up III 48 a A CalComp by TURNING technologies Corporate Headquarters 14557 N 82 Street Scottsdale Arizona 85260 Tel 1 866 746 3015 Support 1 866 746 3015 Fax 480 998 1751 www gtcocalcomp com ROLL UP HI Copyright 2014 GTCO CalComp by Turning Technologies Inc Roll Up Ill is a trademark of GTCO CalComp by Turning Technologies Inc All other products and company names are the trademarks or registered trademarks of their respective owners The information contained in this document is subject to change without notice GTCO CalComp by Turning Technologies assumes no responsibility for technical or editorial errors or
43. s to serial installations only Introduction to the Custom Configuration Menu The Custom Configuration Menu is used to relay configuration information to the Roll Up III in those cases where Table 1 and Table 2 do not supply the information or a SuperSet Menu Code for the graphic application software being used You will use the Custom Configuration Menu to configure the Roll Up Ill for a specific baud rate data format and other operating characteristics that your software requires for communication with the digitizer The Custom Configuration Menu is located in the slot at the end of the Roll Up Ill housing The configuration parameters for Roll Up Ill are divided into three categories e Communication Options e Output Format Options e Mode Options Communication Options e Baud The rate in bits second at which characters are transmitted across the RS 232C serial interface Choices are 1200 2400 4800 9600 19200 or 38400 e Data Bits Data bits represent the actual data being sent from one device to another Both devices must be set for the same number of data bits Choices are Seven 7 or Eight 8 e Stop Bits Each character has one or two stop bits which tell the receiving device that a character is complete The number of stop bits usually does not matter Setting for two stop bits instead of one may overcome a mismatch in parity or data bits Choices are One 1 or Two 2 e Parity One bit can be allocated for parit
44. s will configure the tablet as shown Every time the tablet is powered off and back on or reset it will restore these settings c Save Custom Settings will reconfigure all nine of the tablet s User Defined SuperSet Codes to the settings specified in the corresponding SuperSet Code dropdown list i You can click on the SuperSet Menu buttons on the tablet using the tablet s cursor to activate these configurations S plus 90 through 98 8 When you have finished select Exit or Close from the File menu a Exit will close the Tablet Configuration Utilities b Close will exit the Advanced Configuration Screen and return to the Tablet Configuration Utilities window 14557 N Bond St SIE Le Pon ae a SS 266 746 3015 toll free Scottsdale AZ 88260 WwWww gticocalicomp com 400 998175 fax Roll Up III 40 2 Comp by TURNING technologies _ TURNING technologies Regulatory Statements and Warranty Radio and Television Interference The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not insta
45. sconnect or reconnect the USB cable or restart the system 14557 N Band St SF a ee nun 866 746 5015 toll free Scottsdale AF 25260 wiv gTCOCaIcomp com 400 998175 fax Roll Up III 36 2 Comp by TURNING technologies _ TURNING technologies Load Driver if a window pops up telling you to load a driver every time you power on and your application software does not use a driver you should change the power on default SuperSet Code to SI 9 or load the driver from the TabletWorks CD Procedure A Begin Troubleshooting NOTE This procedure should only be used to troubleshoot serial connections Frocedure A For Serial Unplug the power supply Reset the diaiti and I O cable from the digitizer Plug In the power supply wat for the four beeps then plug in the serial cable To hear the tones again just reset Listen to tones a the digitizer again Compare tones to those in Table 3 Did you hear the four Success tones __ Go to Frocedure B Fossible communication problem between the digitizer and computer Call GTCO CalComp 14557 N Band St Spe hee ees pre 866 746 5015 toll free Scottsdale AZ 25260 www gtcocaicomp com 480 998 1751 fax Roll Up III 37 4 CalComp by TURNING technologies Procedure B Troubleshooting Use Procedure B when the digitizer generates the Success tones but doesnt seem to be communicating with the application program Procedure B
46. stimating applications using a simple code system The SuperSet Menu on the surface of the Roll Up Ill is used to enter the appropriate code for the software being used A table in the Using the SuperSet Menu section of this manual lists the SuperSet Codes for a wide variety of applications Determine if you have not already which communication connection you will be using USB or Serial NOTE Conductive materials inks or electronic devices on under or near the Roll Up Ill can cause improper operation See the Troubleshooting section for more details 14557 N Band St SF a ee nun 866 746 5015 toll free Scottsdale AF 25260 wiv gTCOCaIcomp com 400 998175 fax Roll Up III 7 a 4 CalComp by TURNING technologies 1 Select a large flat nonmetal Surface on which to place the Roll Up Ill Clear all items from the surface 2 Remove the Roll Up Ill from its Power eyes PORTEN cardboard tube container and DC IN unroll it on the selected surface 3 Connect the transducer cursor or stylus to the appropriate jack on the digitizer s Connector Panel The connector is keyed and will fit Roll Up III Connector Panel only the correct jack Do not force it NOTE Do not attempt to remove the controller from the housing Doing so could damage the digitizer and void your warranty USB Connection The Roll Up USB port connection is USB 1 1 and 2 0 compatible When the digitizer is connected to the USB port Windo
47. stom Configuration Menu 1 Place the Custom Configuration Menu card or the copy anywhere in the active area of the digitizer The entire menu must be in the active area A piece of tape can be used to keep it in place during the configuration process 2 Click onthe P button on the SuperSet Menu The alarm will beep slowly indicating that the Custom Configuration Menu Mode is now ready to receive Alignment Point information 3 You will tell the Controller where the Custom Configuration Menu is physically located on the digitizer by clicking on the Alignment Points Click on Alignment Point 1 the white dot in the small blue square labeled Point 1 in the lower left corner of the menu The alarm will beep rapidly indicating that the system is waiting to receive Alignment Point 2 4 Click on Alignment Point 2 the white dot in the small blue square labeled Point 2 in the lower right corner of the menu After Alignment Point 2 is selected the alarm will sound only if the transducer passes over an active block on the menu NOTE If invalid alignment points are selected or if the menu is not entirely in the digitizer s active area the Custom Configuration Menu Mode will be aborted This is indicated by three medium tones from the alarm 5 Configure the Roll Up Ill by selecting the function blocks that correspond to the Settings your software will need to communicate with the digitizer 6 Review the configuration to ensure that the pro
48. t driver releases as well as comprehensive technical support troubleshooting Technical Bulletins and FAQs can be found Telephone Technical Support is available free of charge to the original consumer for a period of 90 days from the date of purchase of the product Please contact our Technical Support Department at 1 866 746 3015 or fax your request to 480 998 1751 Disclaimer of Unstated Warranties The warranty printed above is the only warranty applicable to this purchase ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED Assuming the warranty above stated is otherwise applicable it is expressly understood and agreed that GTCO CalComp by Turning Technologies sole liability whether in contract tort under any warranty in negligence or other shall be for the repair or replacement of the defective parts and under no circumstances shall GTCO CalComp by Turning Technologies be liable for special indirect or 14557 N Band St E SEE 266 746 3015 toll free Roll Up III 47 x A CalComp by TURNING technologies consequential damages The price stated and paid for the equipment is a consideration in limiting GTCO CalComp by Turning Technologies liability Notice Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion may not apply to you This wa
49. ut configuring the Roll Up III again To save the configuration in a user definable location As indicated in Table 2 the codes 90 through 98 are available as storage locations for user defined custom configurations Simply click on the S button and select a two digit number between 90 and 98 Your custom configuration will be saved under that code number for future recall You will hear four short tones when you successfully save the custom configuration Saved configurations allow you to switch quickly between applications Storage locations 90 through 98 retain the saved configurations even when the Roll Up III is turned off or reset Care and Handling of Roll Up III Roll Up III was designed to be both portable and durable As with any product it requires proper care and handling for reliable operation By following these recommendations the Roll Up III digitizer will provide you with many years of service Always use Roll Up Ill on a flat surface where no part of the unit is unsupported Before moving the digitizer disconnect the transducer interface cable and power Supply if connected Before moving the digitizer roll it up The housing along the side of the digitizer is designed as a rolling aid and it allows you to easily control the rolling action See the Transporting Roll Up Ill section on the next page for specific moving instructions Do not permanently attach anything to the digitizer Do not use sharp instruments on
50. ws will recognize that there is a new device connected If Windows displays the Found New Hardware prompt follow the onscreen instructions to complete the driver installation 1 Connect the interface cable to the USB jack on the Roll Up III Connector Panel The connector is keyed and will fit only the correct jack Do not force it 2 Attach the other end of the USB cable to any one of the USB ports lt gt on your computer or USB hub The digitizer will beep four short tones indicating it is powered on View the Roll Up Ill Tones for a complete table of the Roll Up Ill tones 3 SuperSet Codes are not applicable when using the USB connection NOTE Power is supplied through the USB port No additional power source is needed for this installation 14557 N Band St aa 3 866 746 5015 toll free Scottsdale AZ 85260 Wwivw atcocaicomp com 490 998 1751 oo Roll Up III 8 A CalComp by TURNING technologies USB Connections Transducer Computer RS 232 Serial Connection If your software application is not Wintab compliant be sure to set the correct two digit Application SuperSet Code before connecting the serial cable to the computer SuperSet Codes can be found in Table 1 If your application is not listed in Table 1 find the configuration settings that apply to your application in Table 2 and use the corresponding SuperSet Code If an appropriate SuperSet Code is not listed in Table 2 use the Custom Configuration Menu sto
51. y parity is a simple error detecting scheme Both devices Sending and receiving must be set for the same parity either odd parity or even parity or they must be set for no parity Choices are None N Even E or Odd O 14557 N Band St SF a ee nun 256 746 3015 toll free Scottsdale AZ 5760 Vi eV Ve cic Wt a Ol 13 L Ol 490 998 1751 fax Roll Up III 30 2 Comp by TURNING technologies _ TURNING technologies Output Format Options e GTCO Selects GTCO compatible formats See Advanced Programing Information in the Super L VI Online Help for greater detail on GTCO format structure Choices are Binary or ASCII e CalComp Selects CalComp compatible formats See Advanced Programming Information in the Super L VI Online Help for greater detail on CalComp format Structure Choices are Binary ASCII 1 ASCII 2 ASCII 3 or ASCII 4 e Summa Selects Summagraphics compatible formats See Advanced Programming Information in the Super L VI Online Help for greater detail on Summagraphic format structure Choices are Binary or ASCII ASCII formats can be modified by including or excluding a button code decimal point carriage return or line feed depending on whether GTCO CalComp or Summa formats have been selected Mode Options e Button Defines whether the Pushbutton Pb value is included in the ASCII output report This option is available only with GTCO formats Choices are Include or Exclude e Space Defines wheth

Roll-Up III 1 - GTCO CalComp

Contents

Download Pdf Manuals

Related Search

Related Contents