MT6050i MT8050i
Contents
1. Address IP address get from below IP Address 192 168 1 201 Subnet Mask 255 255 1255 10 Gete Way _Cancel Apply Ok lt EasyBuilder 8000 Software Settings NOTE Make sure that all local and national electrical standards are met when CAUTION l 7 Launch EasyBuilder 8000 software select your installing the unit Contact your local authorities to determine which codes apply project file press F7 shortcut key to open the download dialog box The HMI can be powered by DC power only voltage range 24 20 Volts DC compatible with Select Ethernet gt IP tab gt Enter your HMI IP AN Power most controller DC systems The power conditioning circuitry inside the unit is accomplished by a gt Click Download to download this project switching power supply The peak starting current can be as high as 2A file to HMI r a ENE Une user defined startap screen Fusing If the display does not come on within 5 seconds of power up remove power An internal fuse will Please refer to EasyBuilder 8000 User Manual 3 AN Redute prevent damage if the polarity of the DC power is incorrect Check wiring for proper connections for software operation details C ac E and try to power up again i x ti hiar An Internal fuse will prevent damage for over voltage condition however it isn t guaranteed DC Communication Connections NOTE g voltage sources should provide proper isolati2. MT60501 installation and Startup Guide MT80501 Installation Instruction This document covers the installation of MT6050i MT8050i HMI for the detailed specifications and operation please refer to Datasheet and EasyBuilder 8000 User Manual Install Environment NEMA Rating MT6050 8050i Series HMI is NEMA 4X rated Indoor Only MT6050i MT8050i Series has been tested to conform to European CE Electrical Environment requirements This means that the circuitry is designed to resist the effects of electrical noise This does not guarantee noise immunity in severe cases Proper wire routing and grounding will insure proper operation 1 Make sure that the displays are installed correctly and that the operating limits are followed Avoid installing units in environments where severe mechanical vibration or shocks are present 2 Do not operate the unit in areas subject to explosion hazards due to Environmental Considerations flammable gases vapors or dusts Do not install the unit where acid gas such as SO2 exists This device should be mounted in the vertical position and for use on the flat surface enclosure Conform to UL508 ISBN 0 7629 0404 6 machine safety for use in Pollution Degree 2 Environment unpacking the Unit Unpack and check the delivery If damage is found notify the supplier NOTE Place the operator panel on a stable surface during installation Dropping it or lettin
3. g it fall may cause damage 1 Installation Instruction 2 sided A4 1 2 Human Machine Interface 1 3 Power Connector 1 4 Brackets amp Screws V2 1 1 pack 5 Fuse 1 25A 250V 5 20mm 1 nstalation Instructions Secure the operator panel in position using all the fastening holes and the provided brackets and screws ee ee a E el sim MT8050i 119 OPower Connections TTO 24VDC FG 24V DC Osystem Settings When HMI powered up and displays image click the system setting button Default System Password 111111 It is necessary to connect the HMI to your network through a RJ 45 cable Note 1 For the details of HMI DIP SW function settings please refer to Part 8 in this guide cine pa A oo MMA Ad c NOTE 1 Connect positive DC line to the terminal and the DC ground to the terminal 2 Please do not connect HMI with PLC and PC simultaneously to prevent potential difference from destroying USB ports of HMI and PC To make a connection strip about 3 8 of insulation off the end of the wire turn the connector screw counterclockwise until the gap is wide open insert the wire all the way in and turn the screw clockwise until it s tight Go to the Network tab you may choose to auto get DHCP IP or designate your own IP Network Time Date Secunty History Backlight CF card Auto Get IP
4. on from main AC power and similar hazards Only Com1 RS485 2W supports MPI 187 5K Voltage Emergency A Hard wired EMERGENCY STOP should be fitted in any system using a HMI to comply with ICS 2 ae Melony e COM1 RS485 COM COM3 AN Stop Safety Recommendations y RS232 RS485 l COM1 RS485 4 wire 2 wire Supply Do not power the HMI and inductive DC loads or input circuitry to the controller with the same COM3 RS485 power supply Note The 24 VDC output from some controllers may not have enough current to 1 Rx Data 1 yataga ower the HMI Condition P EEE 2 Rx Rx Data a Power wire length should be minimized Max 500m shielded 300m unshielded 6789 3 Tx Tx Wire i AN Routin b Please use twisted pair cables for power wire and signal wire and conform to the impedance 4 TX TX ee matching 5 GND GND c If wiring is to be exposed to lightning or surges use appropriate surge suppression devices d Keep AC high energy and rapidly switching DC power wiring separated from signal wires 6 TxD Transmit e Add a resistor and capacitor in the parallel connection between the ungrounded DC power 7 Data Data supply and the frame ground This provides a path for static and high frequency dissipation Typical values to use are 1M Ohm and 4700pF 8 Data Data DANGER 9 RxD Receive Hardware The system designer should be aware that devices in Controller systems could fail and thereby Cable Different cables are required fo
5. r various devices Considerations create an unsafe condition Furthermore electrical interference in an operator interface can lead to equipment start up which could result in property damage and or physical injury to the operator If you use any programmable control systems that require an operator be aware that this potential Restrict cable length to less than 500 150m for RS485 422 devices and 50 15m for RS232 safety hazard exists and take appropriate precautions Although the specific design steps depend on your particular application the following precautions generally apply to installation of solid state programmable control devices and conform to the guidelines for installation of Controllers recommended in NEMA ICS 3 304 Control Standards Requirement Caution devices to avoid communications problems The COM light on the front of the HMI will turn on with each Ethernet communication Shielded cable must be used for long lengths or cables run in an electrically noisy environment Do not run cables next to AC power lines or near sources of electrical noise Be sure that the cable ends have been inserted all of the way into mating connectors and are secure To conform with ICS Safety Recommendations checks should be placed in the controller to ensure Programming that all writable registers that control critical parts of plant or machinery have limit checks built into Considerations the program with an out of limit safe shut down p
6. rocedure to ensure safety of personnel GME680510_MT6050i_8050i_Installaton_ 121227 ov sw settings Ee Se E Limited Warranty _ __ ON OFF Touch Screen Calibration Mode ON This product is limited warranted against defects in desi ign n and manufacture The proven OFF ON OFF ON OFF Hide HMI System Setting Bar defective product will either be repaired or replaced at Weintek s discretion This warranty OFF OFF ON ON OFF Boot Loader Mode nied MOA COLEA lin OLU Ue US a Out of warranty period which is 1 year from the date of purchase 7934 OFF OFF OFF ON OFF Normal b Damage caused by Force Majeure accident negligence improper installation or misuse SW4 is used for adjusting LCD parameters please keep it in the manufacturer c Product has been repaired or taken apart by unauthorized technicians default position otherwise incorrect screen display may occur If the default of d Products whose identification markings have been removed or damaged SW4 is ON the switch is cut by manufacturer
Download Pdf Manuals
Related Search