User manual
Contents
1. 7 Audio Disto rtion 1KHZ 1000mv inp ut 0 3 8 Speaker Output Power 1 KHZ 1000mv inp ut max volume W 0 5 9 Transmission Frequency F1 F2 F3 F4 MHZ ISM 2414 2432 2450 2468 10 FM Transmitter Output Level NW 40 11 Wirele ss earphone receivin g fre quency MHZ 107 9 12 Wirele ss earphone receivin g distance M 1 0 13 Wirele ss earphone output power MW 60 14 Wirele ss earphone charging time 2 15 Wirele ss earphone working time 4 6 16 Received Sensitity DB lt 85 17 Mirror Consumption Curre nt M AX MA 600 18 Unobstructed Effective Range Min M 40 19 Mirror Dimensions W X D XH MM 285X90X24 20 Mirror Weight a bout G 370 21 Camera Imaging Sensor CMOS 22 Camera Total Pixels 720x480 NTSC 720x576 PAL 23 Camera Horizo ntal View Angle Degree 80 24 Camera Transmission Power MW 2 FCC 10 CE 25 Camera Minim um illum ination 0 Lux IR ON 26 Camera IR Night Range M 4 27 Camera Power Supply Supplied By Transmission Box 28 Camera Consumption Curre nt M ax MA 120 29 Camera Dimensions WxDxH mm 525x148x45 30 Camera Weight about G 264 Actual transmission range may vary according to the weather location interference and building construction All the specifications are subject to minor change without prior notice 16 Declaration of Conformity We Trebs BV declare under our sole responsibility that this product is in conformity with the essential r2. 10 VOLUME CONTROL 10 MUTE CONTROL 10 ANSWER MODE SET 11 SELECTRINGTONE 11 BLUETOOTH AV DEVICE OPERATION 11 SWITCH AUDIO OUTPUT MODE AND PICTURE ADJUSTMENT 12 FM HEADSET USE 13 To Set Audio On and Off 14 To Resume Factory Default Mode 14 WIRELESS CAMERA SYSTEM 14 PHONE BOOK 15 SELECT LAST 10 CALLS DIAL BACK FROM MIRROR 15 Frequently asked questions 15 SPECIFICATION 16 Welcome Thank you for the purchase of this Bluetooth Handsfree Car Kit For the sake of making full use of the functions of Bluetooth Car Kit please read the user manual carefully in advance Drive safely Itis dangerous to use cellphone when driving a car It will increase the possibility of accident Please reduce conversation time by mobile as possible as you can while driving It is good for you not to do any record or read You d better observe
3. User manual Bluetooth Hands free amp 2 4Ghz Wireless Rearview Mirror System TRE B5 132 CONTENTS iForeword o 1 2 Packing List suser 1 3 Structure vedit Nasa iaa ieee abnaki 2 4 Installation CADERA ewan vv FEREARE dinja KI KARRE RRIA jaja 4 5 Specifications eatoni h ohh 9 Comfortcam is not responsible for any damage resulting from installation and use of this product 2 4 GHz devices as e g cell phones navigation bluetooth and Wi Fi system scan have influence on the performance of this product FOREWORD CONGRATULATIONS CC 120 is a Bluetooth Hands free amp 2 4GHz Wireless Rearview Mirror System with 3 5 TFT LCD monitor The system can make you to drive more safely and more convenient and also provides you more recognition of backside image display The Rearview Camera when used as described will give you years of dependable service in your car or mini van We have taken numerous measures in quality control to ensure that your product arrives in top condition and will perform to your satisfaction PACKING LIST 1 Rearview Camera Wired Camera with Night Vision 2 Monitor 3 5 inch TFT LCD with 960 240 resolution 3 Earphone 4 Wireless Transmission Box Connected to wired camera car power wire It transmits signals to monitor 5 Power Adapter 12 Volt Car Power Adapter and built in 2 4GHz wireless receiver 6 Audio
4. a call 1 4 Volume VOL VOL Set volume select ring tone track skip if Bluetooth compatible audio device plays 1 5 Power connector PWR DC 12V input 1 6 Audio input connector AUDIO Connect to audio source such as MP3 MP4 or CD player While handsfree system is vacant No call or Bluetooth AV activities press PLAY key twice to open audio input MEDIA PLAY will be displayed on mirror and the mirror can work as an stereo sound box or FM audio adapter in FM mode 1 7 3 5 inch TFT display Call ID display Camera display Video in display 1 8 Speaker Built in dual channel stereo loud speaker 1 9 Microphone Built in microphone 1 10 Indicator lamp State indicator lamp 2 INSTALLATION Easy installation step as following 2 1 Hook bottom stator of the mirror on original rearview mirror bottom edge Ensure perpendicular bisector of the mirror is congruent with perpendicular bisector of original rearview mirror Pull up stator of the mirror until it is fix on original rearview mirror up and bottom stator will adjust by spring Then release hand 2 2 Check if the mirror has been firmly clipped to the original rearview mirror the congruence of the mirror compare to Original rearview mirror and adjust accordingly 2 3 If there is any loose repeat above steps 2 4 Plug the power adapter into the cigarette socket 3 Turn mirror ON OFF Press multi function button TALK and hold for 1 5 seconds u
5. last answered call then press VOL or VOL button to scroll the last 10 calls press TALK button to dial the number 22 SWITCH TO VIDEO INPUT MODE Press and hold PLAY key for 3 seconds to switch to video input mode you can connect the video in socket to a video source Press and hold PLAY key for 3 seconds again to exit video input mode 23 Frequently asked questions 23 1 Can Bluetooth mirror connect to any bluetooth devices Re Bluetooth mirror can connect with any bluetooth devices which support headset profile or handsfree profile But different bluetooth devices may have different operation For the mobile supporting headset profile it disconnects normally but it can connect to handsfree automatically and cannot display caller ID 23 2 What is useful distance between Bluetooth mirror and phone Re Usually distance between device and phone is 10M 23 3 Does any interference when use Bluetooth mirror Re Wireless and wireless network devices may have interference during communication Use bluetooth devices and keep away from RF generator will reduce interference 15 SPECIFICATION SECTION UNIT DATA 1 Blue tooth Standard Bluetooth 2 0 EDR 2 Blue tooth Frequency 2 4GHz ISM band 4 3 5 inch TFT LCD with vesolutio n 960X240 3 Blue tooth Transmit Power lt 4dBm cla ss 2 communication dista nce 10 meters 5 Power Supply 9V 15V 6 Operating Temperature 10 C 60 C
6. on mirror shortly press PLAY key twice again to shut the audio input MEDIA OFF will be displayed on mirror 18 To Resume Factory Default Mode Press and hold VOLt and VOL key together for 10 seconds to resume factory defaule mode DELALL BT will be displayed on mirror all bluetooth device will be cancelled 19 REARVIEW SYSTEM While car backward the rearview system auto start working the image of back around from camera will be displayed on mirror There will be several different transmitting and receiving frequency the box will be marked 1 2 3 4 to represent different frequencies 2414MHz 2432MHz 2450MHz 2468MHz The same tag can be used in conjunction with transmitting and reveiving 14 20 PHONE BOOK 1 First store phone number into your mobile with English name 2 Press MODE button twice to enter address list transfer B CARD READY will be displayed on mirror To choose address list transfer by bluetooth from mobile phone 3 The English name will be displayed on mirror if transfer success 4 Max 200 address can be stored Ifover 200 address the new address will cover the earlier 5 To delete address list Press and hold PLAY button for 6 seconds DELETE PB will be displayed on mirror press PLAY button twice within period of 15 seconds to delete phone book 21 SELECT LAST 10 CALLS DIAL BACK FROM BLUETOOTH MIRROR Press TALK button twice to resume the
7. re install the light socket Re attach the negative battery cable to the battery Engage the parking brake and turn the ignition key to the ON position DO NOT start the vehicle Put the gear shift into reverse The camera will start broadcasting and the monitor will detect the signal and turn itself ON If the monitor does not come ON press the ON OFF button If the image does not match your rear view mirror press the mode button on the monitor to change the image until it matches your rear view mirror When you take the gear shift out of reverse the camera will turn OFF and the monitor will turn black INSTALLATION Installation of the camera 1 Loosen the license plate bolt or screw and then remove the license plate on the rear of your car 2 Drill one hole for power cable in the middle of below license plate where the camera will exist 3 Install the frame camera with bolt screw and adjust the camera to a suitable angle Tow the power wire into the car through the interstices of the car 4 Install the license plate to the frame Wireless Transmission Box Installation 1 Wiring Connector Diagram 12V REV LAMP RED Wireless Camera _ Transmission Reverse Lamp Box BLACK GROUND 2 Basic Installation 1 Find proper spaces for install the transmission box 2 Connec
8. ansmission Box Consumption Current Max 120mA Dimensions WxDXxH 525X148 x 45 mm Weight about 264g LCD Screen Type 3 5 TFT LCD Effective Pixels 960 X 240 L Received Sensitivity lt 85dBm e Povver Supply Voltage 12Vpc E Consumption Current Max 600mA Unobstructed Effective Range Min 40m Dimensions WXDXH 285 X9OX24 mm Weight about 370g Transmission Frequency ISM 2 400 2 483 MHz Actual transmission range may vary according to the weather location interference and building construction All the specifications are subject to minor change without prior notice CAUTIONS 1 The system voltage is 9V 15V Do NOT use the system for vehicles with voltage system higher than 15V this will cause irreparable damage 2 The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 3 The transmitter is integrated in the car adaptor Do not make any adjustments 4 The adapter built in wireless transmission mould don t change it in any situation 5 The camera receiver can only be completely disconnected from the mains by unplug the adapter 6 Do not cut the DC power cable of the apparatus to fit with another power source 7 Attention should be drawn to the environment aspects of battery disposal 10 Declaration of Conformity We Trebs BV declare under our sole responsibility that this product i
9. cable for listening MP3 7 3Fuse and sticker Fuse is accessory for power adaptor and sticker is for wireless receiver if necessary 8 In Line Wire Connectors To expose reverse light wires 9 Sheet Metal Screws To install camera Charge port Earphone Power switch No function Indicator LED RED FOR POWER ON GREEN FOR CHARGING Frame IR LEDs Lens U Power plug L Wireless Transmission Box Wireless Transmission Box Power Wire Connect Wire UL Rearview Camera a p N TFT LCD Monitor CHARGE HOLDER LI Bluetooth System CALLIN gt es SPEAKER _075 5123456 78 SPEAKER JA e JE INDICATOR LAMP NS Lee nA AUDIO IN VOL VOL SEND TALK MODE PLAY MICROPHONE We advise to test the system before installation to prevent any damage on the vehicle Follow the steps mentioned below precisely to test the system 1 2 3 Connect 12V car adaptor to the vehicle s cigarette lighter and connect the black and yellow plugs to the monitor Search at the rear of the vehicle for find back up light wiring Splice the red wire of the Transmission Box power cable to the reverse light s positive wire of the vehicle Splice the black wire of the Transmission Box power cable to the reverse light s negative wire of the vehicle Replace the reverse light bulb and then
10. connected to device Blue LED is flash 2 Incoming call The mirror shows who is calling and the device rings If the caller is unknown the device only rings 3 Short press function button TALK once ANSWER CALL ACTIVE will be displayed on mirror 4 Short press function button TALK once again to hang up a call during call active HANG UP will be displayed on mirror Note Some mobile is in disconnected state after pair it will automatically connect to the device when has an incoming call Some mobile phone may not support the caller ID indication function and the caller ID will not be displayed 8 CALL REJECT STEP STATE RESULT 1 Ensure mobile has connected Blue LED is flash to device The mirror displays which ring tone is set 2 Incoming call Or only ring but doesn t display caller ID 3 Press and hold function button REJECT will be displayed on TALK for 1 5 seconds reject mirror 9 AUDIO TRANSFER During call active or call out going state Press and hold function TALK button and hold for 1 5 seconds to switch the call between Bluetooth handsfree and mobile MIRROR PHONE MOBILE PHONE will be displayed on mirror 10 VOLUME CONTROL Press VOL to increase volume press VOL to decrease volume 11 ANSWER MODE SET In idle state hold both VOL and VOL for 1 5 seconds to s
11. equirements and other relevant requirements of the R amp TTE Directive 1999 5 EC The product is compliant with the following standards and or other normative documents EN301 489 1 V1 8 1 2008 04 EN301 489 17 V2 1 1 2009 02 EN300 328 V1 7 1 2006 10 Trebs BV The Netherlands Website www trebs nl email info trebs nl CE Trebs Comfortcam is a brand of Trebs BV All other brands in this manual and or packaging do not belong to Trebs BV and have another justified holder EU Environmental Protection Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice 447
12. et the answer mode as auto answer or manual answer 12 MUTE CONTROL During active call press PLAY button and hold for 1 5 seconds to mute microphone MUTE ON will be displayed on mirror long press PLAY button 1 5S again to release mute MUTE OFF will be displayed on mirror 10 13 SELECT RING TONE Press the VOL or VOL key and hold for 3 seconds to select the ring tone total 16 sorts of ring tones are available 14 BLUETOOTH AV DEVICE OPERATION STEP STATE RESULT 1 If AV not connected shortly press PLAY key to connect BT STEREO will be displayed on mirror 2 Shortly press PLAY key to play or pause playback AV PLAY or AV PAUSE will be displayed on mirror 3 Press and hold PLAY key for 1 5S to stop playback AV STOP will be displayed on mirror 4 Long press VOL or VOL button for 1 5 seconds and release once heard an prompt tone to skip forward or skip AV FORWARD or AV BACKWARD will be displayed on mirror 11 15 SWITCH AUDIO OUTPUT MODE AND PICTURE ADJUSTMENT STEP STATE RESULT 1 The default mode of audio output is speaker mode SPEAKER will be displayed on mirror and green LED will be on 2 Shortly press MODE key to switch to FM transmitter mode FM will be displayed on mirror and right red LED will be on 3 At FM tran
13. l be displayed on mirror and blue LED is on B If the mobile was not connected after paired just short press the TALK button the Bluetooth mirror will try to connect mobile phone As above 5 VOICE DIAL STEP STATE RESULT 1 Ensure mobile has connected to device Blue LED is flash 2 Short press function button TALK VOICE DIAL will be displayed on mirror The device will send voice dial prompt 3 Bring out a pre recorded voice tag The mobile will dial number CALL OUT will be displayed on mirror Note This function used only the user mobile phone supports the voice dial function Please re details fer to mobile user manual for 6 REDIALLING THE LAST DIALED NUMBER STEP STATE RESULT 1 Ensure mobile has connected to device Blue LED is flash 2 Press and hold function button TALK for 1 5 seconds REDIAL will be displayed on mirror Dial the last number CALL OUT will be displayed on mirror 3 Press function button TALK once again will hangup the out going call just now HANG UP will be displayed on mirror Note This function depends on the feature of mobile Please refer to mobile user manual When you find the outgoing call number is not the desired use Step 3 to cancel it 7 CALL ANSWER AND CALL HANG UP STEP STATE RESULT 1 Ensure mobile has
14. ntil POWER ON The mirror sounds a brief beep tone then release it The device is turned on Once power on the device will auto connect the latest used cellphone if never paired with any cellphone yet the device will enter pairing state Press multi function TALK key and hold for more than 5 seconds Until POWER OFF is displayed on mirror The mirror sounds a brief beep tone The device is turned off 4 PAIRING Pair means the handsfree system and mobile phone authenticate each other and store the authentication information Only paired devices can establish link and audio connection STEP STATE RESULT 1 In power off state press and hold TALK button for more than 5 seconds until Blue LED and red LED flash alternately to enter pairing state Blue LED and red LED will flash alternately PAIR ON will be displayed on mirror 2 Select Search for Bluetooth devices on your mobile phone Please refer to mobile user manual After searching finished the mobile will display all found Bluetooth devices 3 According to the mobile prompt Information select WINS in device list 4 Enter Pin code 0000 to confirm the pairing Pairing information will be stored PAIR SUCCESS will be displayed on mirror once paired successfully a Some mobile can connect to the device automatically after pairing successfully such as nokia MB CONNECTED wil
15. s in conformity with the essential requirements and other relevant requirements of the R amp TTE Directive 1999 5 EC The product is compliant with the following standards and or other normative documents EN 50371 2002 EN 60065 2002 Al 2006 EN301 489 3 vl 4 1 2002 08 EN300 440 2 vl 2 1 2008 05 Trebs BV Thermiekstraat 1 6361 HB Nuth The Netherlands Website www trebs nl email info trebs nl Trebs Comfortcam is a brand of Trebs BV All other brands in this manual and or packaging do not belong to Trebs BV and have another justified holder EU Environmental Protection Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice E BLUETOOTH User manual 3 0 for model CC 120 CONTENTS WELCOME amp DRIVE SAFELY 2 ILLUSTRATION Figure 1 3 INTRODUCTION dia i co ee iii 4 INSTALLATION 5 POWER ON OFF amp PAIRING 6 VOICE DIAL ae oc soil oba osijek ee a 7 REDIALLING THE LAST DIALED NUMBER 8 CALL ANSWER AND CALL HANG UP 9 CALL REJECT 10 AUDIO TRANSFER
16. smitter mode press and hold MODE key to select to the desired transmitting frequency then tune your car radio to receive the frequency accordingly Selected transmitting frequency will be displayed on mirror 87 7 87 9 88 1 88 3 88 5 88 7 88 9 4 Shortly press MODE key to switch to picture adjustment mode Picture menu will be displayed on mirror press and hold MODE key to select item BRIGHTNESS or CONTRAST or COLOR use VOLt and VOL to change the value 12 16 FM HEADSET USE CHARGE PORT POWER SWITCH NO FUNCTION INDICATOR LED RED FOR POWE ON GREEN FOR CHANGING To make use of the Fm headset from the charging point on the mirror take them from the mirror In the case the audio output mode automatically change to FM 107 9 the receiving frequency of the FM headset Then press the headset button to turn on the headset red led on to start talk The operation range is about 1m Once headset put back to the charging socket the audio output mode will be auto restored to the mode before headset unplug Attention Keep volume below 11 to avoid noise when using FM headset If there is a radio station 107 9MHZ it may interfere with FM headset 13 17 To Set Audio On and Off When the handsfree system is vacant no call in or call out you can open the audio input by shortly pressing PLAY key twice MEDIA PLAY will be displayed
17. t the red wire of the transmitter to the positive wire of the back up light Connect the black wire of the transmitter to the vehicle ground 3 Connect the yellow plug of the transmitter to the yellow socket of the camera Connect the black plug of the transmitter to the red socket of the camera If the cable is too short extend with the supplied extension cable 4 Instructions Line In Connection Before connecting the transmitter you may use the line in connection ES Insert the existing vvire to be tapped Insert the wire to be attached 7 Crimp tap then close lock 3 BLUETOOTH installations Please refer to extra manual of BLUETOOTH User manual 3 0 Installation of the monitor 1 Camera is be attached the front rearview mirror instead of the front rearview mirror 2 Connect power of the monitor To use the car power adapter included in the package to get the power 3 Power ON and adjust brightness etc according to the details manuals of Bluetooth es gt Le Uoo SPECIFICATIONS Items CC 120 Imaging Sensor CMOS Total Pixels 720x 480 NTSC 720 x 576 PAL Horizontal View Angle 80 degree g Transmission Power 2mW FCC 10wm CE o Minimum Illumination 0 Lux IR ON E IR Night Range 4m O Power Supply Supplied By Tr
18. the surroundings before using the mobile first When it s necessary if the weather is bad there is traffic jam there are children in the car or something wrong with the car You should leave the road and stop the car before dialing or receiving a call ILLUSTRATION DC 12V OUTPUT MPSMPA cable white s VIDEO YELLOW VIDEO YELLOW Figure 1 CHARGE HOLDER F3 POWER 4 Bluetooth System CALLIN 075512345678 JACK gt o 3 INDICATOR LAMP SPEAKER VOL VOL SEND TALK ON OFF CIGARETTE POWER JES L MODE PLAY ANTENNA BOX MICROPHONE YELLOW YELLOW GND pil CAMERA BACKUP LIGHT 1 INTRODUCTION The Bluetooth handsfree car kit mirror compose of the parts shown as Figure 1 1 11 1 Mode selector Press the button to cycle through audio output transmission frequency monitor setup Press and hold the button for 1 5 seconds to access the FM CHANNEL menu You can set the frequency Press and hold to cycle through the transmission frquencies 7 settings are available 1 2 Function button PLAY 1 2 During active call the sound mutes if pause or stop mode is selected on a Bluetooth AV device Press and hold the button for 3 seconds to switch to video mode 1 3 Multi function button TALK 1 3 Turn mirror on off answering a call hanging up acall voice dialing last number redialing rejecting
Download Pdf Manuals
Related Search