Untitled
Contents
1. 12 2 Fixing of knobs push buttons keys and levers N 12 3 Remote controls with hazardous live parts No such remote controls N 12 4 Drawers pull test 50 N 10 s No drawer N 12 5 Antenna coaxial sockets providing isolation No antenna coaxial socket N providing isolation 12 6 Telescoping or rod antennas construction No such device N 12 6 1 Telescoping or rod antennas securement No such device N 13 CLEARANCE AND CREEPAGE DISTANCES P 13 1 Clearances in accordance with 13 3 P Creepage distances in accordance with 13 4 P 13 2 Determination of operating voltage Considered P 13 3 Clearances see appended table P 13 3 1 General P 13 3 2 Circuits conductively connected to the mains P comply with table 8 and where applicable table 9 13 3 3 Circuits not conductively connected to the mains P comply with table 10 13 3 4 Measurement of transient voltages N 13 4 Creepage distances see appended table P Creepage distances greater than table 11 minima P 13 5 Printed boards P 13 5 1 Clearances and creepage distances between P conductors on printed circuit boards one of which may be conductively connected to the mains as in fig 10 13 5 2 Type B coated printed circuit boards complying No such printed board used N with IEC 60664 3 basic insulation only 13 6 Conductive parts along uncemented joints No such part N clearances and creepage distances comply with 13 3 and 13 4 Conductive parts along reliably cemented joints N2. Report reference No WT093001905 Page 17 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 17 8 Fixing devices for detachable legs or stands No such device N provided 17 9 Internal pluggable connections affecting safety N unlikely to become disconnected 18 MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST N THE EFFECTS OF IMPLOSION Picture tube separately approved to IEC 61965 No picture tube N Picture tube separately approved to 18 1 N 18 1 Picture tubes gt 16 cm intrinsically protected N Non intrinsically protected tubes gt 16 cm used with N protective screen Protective film as part of implosion protection N edges covered by enclosure 18 2 Intrinsically protected tubes tests on 12 samples N 18 2 1 Samples subject to ageing 6 N 18 2 2 Samples subject to implosion test 6 N 18 2 3 Samples subject to mechanical strength test steel N ball 6 18 3 Non intrinsically protected tubes tested to 18 3 N 19 STABILITY AND MECHANICAL HAZARDS Mass of the equipment exceeding 7 kg 5 Less than 7 kg Apparatus intended to be fastened in place N suitable instructions 19 1 Test on a plane inclined at 10 to the horizontal N 19 2 100 N force applied vertically downwards 19 3 100 N force or 13 of weight applied horizontally to point of least stability 19 4 Edges or
3. 16 EXTERNAL FLEXIBLE CORDS 16 1 Mains cords sheathed type complying with VDE approved IEC 60227 IEC 60227 for PVC or IEC 60245 for synthetic PVC cord used MUDDEr COMdS aera aid teatie nia A a a Non detachable cords for Class have Class Il equipment N green yellow core for protective earth 16 2 Mains cords conductors have adequate cross 0 5mm the length of the P sectional area for rated current consumption of the power supply cord is less than equipment 2m 16 3 a Flexible cords not complying with 16 1 used for NO such flexible cords N interconnections between separate units of equipment used in combination and carrying hazardous live voltages have adequate dielectric strength b Flexible cords not complying with 16 1 No such flexible cords N withstand bending and mechanical stress 3 2 of IEC 60227 2 Report reference No WT093001905 Page 16 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 16 4 Flexible cords used for connection between No such flexible cord N equipment have adequate cross sectional areas to avoid temperature rise under normal and fault conditions 16 5 Adequate strain relief on external flexible cords Not possible to push cord back into equipment Strain relief device unlikely to damage flexible cord Z U0 U U For mains cords of Class equipment hazardous Class Il equipment live conductors become taut be
4. c Discharge not exceeding 45 uC lt 1puC d Energy of discharge not exceeding 350 mJ No voltage exceeding 15 kV de REINFORCED insulation Class II 9 1 1 2 Test with test finger and test probe No hazard live parts accessible 9 1 2 No hazardous live shafts of knobs handles or No hazardous live shafts levers 9 1 3 Ventilation holes and other holes tested by means No epeninas omtobendos re N of 4 mm x 100 mm test pin p 9 p 9 1 4 Terminal devices tested with 1 mm x 20 mm test No havaid live pans accessible P pin 10 N test probe D of IEC 61032 p Terminal devices tested with 1mm x 100 mm No hazardiliveparts accessible P straight wire 1 N test probe D of IEC 61032 p 9 1 5 Pre set controls tested with 2 5 mm x 100 mm test No presetcontrole N pin 10 N test probe C of IEC 61032 p 9 1 6 No shock hazard due to stored charge on OV under normal condition P withdrawal of the mains plug voltage V after 2 s OV under single fault condition If C is not greater than 0 1 uF no test needed N 9 1 7 a Enclosure sufficiently resistant to external force P Test probe 11 of IEC 61032 for 10 s 50 N No damage P b Test hook of fig 4 for 10 s 20 N No damage P c 30 mm diameter test tool for 5 s 100 or 250 N No damage P 9 2 No hazard after removing a cover by hand No removable cover by hand N 10 INSULATION REQUIREMENTS 10 1 Insulation resistance MQ at
5. Requremenia and application guide Fire hazard testing Part 2 Test methods Section Needietlame test Fire hazard testing Part 11 10 Test flames 0 W horizontal and vartcal lame tasi meathocs Flamimabiity of scl non metallic materials when eoipomed to Mame sources List of test meinods Aubele electical controle for household and similar use Safety of laser products Part 1 Equipment classification requirements and user s guide Winding wires Test methods Pigs and socked ouileis for houeehold and similar purporas Eleciical iesi methods tor electric cables Fan 1 Electrical teste for cables cords ard wires for wollages ua bo and induding 450750 W IEC sysiem of plugs and socket outlets for household and similar purposes Safety of infannation tecinakgy quinmert Kietheds of measurement of jouch current and protective conductor current Connecting devines far lowe tage ircuits for household and similar purposes Part 2 2 Partioular requirements for COnmecing devices as separale enht es wih serewlass hype damping units EN G0664 3 EN 60631 EM G0605 2 2 EN 0655 11 10 Al EN Bray EM gral EN 61625 1 corr February Ai A AD oor April EN 60851 EH aasi com February EW 603o0 EN 5090 2 2 Requirement Test Result Remark 203 gering 1534 i1636 2002 2001 2004 SETMES Page 33 of 49 IEG 0pais 1 IES 1032 IEG GIH IEC 6105847 1
6. Ambient temperature t1 ATEA 24 1 198V 24 3 264V oS Ambient temperature t2 24 4 198V 25 3 264V Temperature rise dT of winding R2 Q dT K Limit dT K class E 72 TABLE softening temperature of thermoplastics ON Temperature T of part T normal condi T fault condi T softening tions C tions C CC TABLE Electric shock hazard under normal condition OOP Measured between Required U1 Required U2 Vpk Vpk L N and metal enclosure 35 0 35 L N and signal terminal 35 0 35 10 3 TABLE insulation resistance measurements Insulation resistance R between R MQ Required R MQ Primary and secondary coil of the T1 Secondary coil and the core of the T1 TABLE electric strength measurements oP Test voltage applied between Test voltage V L and N switch open 1500 No L N and signal terminal 3000 Primary and secondary coil of the T1 3000 Secondary coil and the core of the T1 3000 Report reference No WT093001905 Page 37 of 49 11 2 TABLE summary of fault condition tests oP Voltage V 0 9 or 1 1 times rated voltage See below Ambient temperature C c ccccccscscsceseseseteeeesees 2 25 C 27 C fault condition state component short or open supply result state effect of fault condition and the circuited and components whose temperature duration of the test rises
7. comply with 8 8 Temperature cycle test and dielectric strength test N 13 7 Enclosed enveloped or hermetically sealed parts N not conductively connected to the mains clearances and creepage distances as in table 12 13 8 Parts filled with insulating compound meeting the OPtocoupler separately P requirements of 8 8 approved Report reference No WT093001905 Page 10 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 14 COMPONENTS 14 1 Resistors a Resistors between hazardous live parts and accessible metal parts No such component b Resistors other than between hazardous live parts and accessible parts Resistors separately approved ceeeeees 14 2 Capacitors and RC units Capacitors separately approved 14 2 1 Y capacitors tested to IEC 60384 14 2 edition Y capacitors separately approved v uvuz 14 2 2 X capacitors tested to IEC 60384 14 2 edition X capacitors separately approved 14 2 3 Capacitors operating at mains frequency but not connected to the mains tests for X2 0 14 2 5 Capacitors with volume exceeding 1750 mm where short circuit current exceeds 0 2 A compliance with IEC60384 1 4 38 category B or Detter om cs feceti ee cdcooiebeswons eiiewwes NEE No such capacitor Capacitors with volume exceeding 1750 mm mounted closer to a potential ignition source th
8. group safety publications ISD general purpose melre screw threads General plan Requirement Test Result Remark EN 5395 1 EH 1032 EH 610581 EN 67260 EH 61293 EH 81558 1 Al All corr dori EN 61556 2 17 EW 61985 EN 62087 Page 34 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark ISO general purpose metric screw threads Selected aes for screws bolts and ruts Plastics Thernoplas c materials EN ISO a4 136 Determination of Viral softening temperature v5 20 TOC Graphical symbals for use on equipment index and Sere MU T Te sis on powered repeaters using solid Recommendation siate devices in order ta check the Kit arrangements for prabectian from externa interference TU T 1858 Resesbiity of telecommurecation Recommendation equipment ingtaled in customers premises k i fo cwervoltages and pvercuments Report reference No WT093001905 Page 35 of 49 TABLE temperature rise measurements Ses P Power consumption in the OFF Stand by 2 43W oa Position of the functional switch W j Operating conditions Normal working a 198V 50Hz 63 2 220V 60Hz 240V 60Hz 264V 60Hz a Loudspeaker impedance Q ee n S a ee Monitored point Limit dT K oe a aceasta ee eee ee oO NIN O Report reference No WT093001905 Page 36 of 49 Operating conditions fF Winding temperature rise measurements _
9. mod IECITR2 61149 IES 81250 IES 61293 IEC 1556 1 modi Aj IES 1556 2 17 IES 81945 IES 62087 IEC 62757 IES Guide 104 50 261 Report reference No WT093001905 EN 60065 2002 A1 2006 Connecting devices Safety requirements for strew bype and scrvless fype clamping wiis Pant i General requirements and particular requirements Tar clamping units Tor h conduciors from 0 2 mm up ie 35 mm included Projection of persons and equipment by enclosures Probes for verification Wanghors Tor use in elecsiani equipment Pan 2 Sectonal specification for surge suppression varistor Swtiches for appliances Part i General requirements Guide tor sa e handling and operasion of mobile radio equipment Elecinacoustics Ocheye hand ard fractional octave band fillers Marking of electrical equipement with ratings related io electrical supply Safety requirements Safety of power fransformers power supply units and similar Part 1 General requirements and tests Safety of power franstorners power supply units and similar Part 2 17 Particular requirements Tor transformers for switch mode power supplies Mechanical safety of cathode ray tubes Methais of easLinenen for Tie power cengumpiion of audia vides and related equipment Safety of equipment electrically conneeled to a felecommunicaton mebyvork The preparation of safety publications ard tha use of basic sa eby publications and
10. 9 2 Floating secondary circuits of Class apparatus which have connector terminals that could be earthed e g antenna signal input are subjected to the requirements for circuits conductively connected to the mains in Tables 8 and 9 unless the floating secondary circuit is separated from the primary circuits by an earthed metal screen e g in the power transformer or the floating secondary circuit is connected to earth via a component such as a capacitor 3 For insufficient clearances and creepage distances from secondary to secondary circuits and from secondary circuits to earth see Cl 4 3 1 4 3 2 and 11 2 4 If the minimum creepage distance in Table 11 is less than the minimum required clearance in Tables 8 9 or 10 as required then the value for clearance is used as the minimum creepage distance Min minimum required Actual Actual dimensions measured Report reference No WT093001905 Page 39 of 49 Report reference No WT093001905 Page 40 of 49 TABLE list of critical components and materials oP Component Manufacturer Type model Value rating Standard Approval trademark Reference Power cord Shenzhen HO3VVH2 F 2x0 5mm VDE 0281 5 VDE 103727 Baohing Electric EU Wire amp Cable Manufacture Co Ltd Power plug Ching Cheng EL 207 2 5A 250V VDE 0620 VDE EU Wire Material 40002990 Co Ltd alt Shenzhen Hong HYP 201 2 5A 250V VDE 0620 VDE Yun 4002194
11. equipment The following is added Certain types of CLASS apparatus see 15 1 1 may be provided with a plug not establishing earthing continuity when inserted in Danish socket outlets Justification Heavy Current Regulations Section 107 C Add the following indent at the end of the list exposure to excessive sound pressures from headphones or earphones NOTE A new method of measurement is described in EN 50332 1 Sound system equipment Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit consideration Part 1 General method for one package equipment and in EN 50032 2 Sound system equipment Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 2 Gudielines to associate sets with headphones coming from different manufactures The following marking are required In case of intrinsically ionizing radiation safe cathode ray tubes with accelerating voltages betwwen 20kV and 30kV Report reference No WT093001905 Page 21 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark On the cathode ray tube itself the wording Eigensichere Kathodenstrahlrohre nach Anlage III R ntgen verordnung Inside the apparatus the maximum allowed accelerating voltage in kV and the maximum allowed beam current in mA On the outer o
12. series not modified IEC 61040 1990 NOTE Harmonized as EN 61040 1992 not modified IEC 61558 2 1 1997 NOTE Harmonized as EN 61558 2 1 1997 not modified IEC 61558 2 4 1997 NOTE Harmonized as EN 61558 2 4 1997 not modified IEC 61558 2 6 1997 NOTE Harmonized as EN 61558 2 6 1997 not modified IEC 61558 2 9 NOTE Hamonized as EN 60598 2 9 1989 A1 1994 not modified IEC 61558 2 17 NOTE Harmonized as EN 60598 2 17 1989 A2 1991 not modidied common modification indicated by mod the relevant EN HD applies Annex ZA C other international plublications quoted in this standard with the reference of the relevant European publications This European Standard incorporateds by dated or undated referenece For dated references subsequent amendments to or revisions of any of these publications apply to this European Standard only when iincorporated in it by amendment or revision For undated references the lasted edition of the publication refered to applies including amendments NOTE When an international standard has been modified by Report reference No WT093001905 Page 30 of 49 IEC aod IEC p036 IEC 9006 2 6 corr March IEC G008G 2 32 IEC GDOGE 2 F5 IEC 5006 2 78 IEC 50085 IEC 9006 4 IEC 0 12 IEC 80127 IEC 6tiT IEC 60216 IEC 80227 mad IEC 60245 mod IEC 0249 2 IEG GUZES 1 Report reference No WT093001905 EN 60065 2002 A1 2006 Tiie AldiG
13. video and similar eeciranig apparalus Routne electrical satety besding in produzion Letar symbols to be Weed in elecincal lechnology IEG standard wokagen Ersironmental tesir Part 2 Tests Tesi F Vibration ESATE TALESIN Environmental testing Part 2 Tesis Tesi Ed Free fall Envirannental tesir Part 2 Tesis Test Eh Hammer tests Envirenmnental tesir Part 2 Tesis Test Cab Damp heat sleady stale Thermal evaluation and classification of Alectical inaulalicn Primary batteries Part 4 Safety of ithium batteries Method tor deiermining the comparative and the proof iracking indices af salid insulating malerials under moet conditions Miniature fuses Methods of best for the determination of the insulation resistance of solid insulaling materials Electical irculating materials Properties of thermal endurance Polvinyl chioride insulated cables of rated voltages up io and including 450 750 W Rubber insulated cables Rated voltages up to ard induding 4507S Base materials for priried circuits Pan 2 Spectications Sound system equipment Part 1 Garsral Requirement Test Result Remark EHD EH 50333 HD OME7 EH 60066 2 6 EN 0065 2 32 EH 5006 2 75 EH 0066 2 78 EH 60085 EH 60086 4 EW 60112 EW 60127 HD BAA Si HO 611 EN 0216 EM 602d9 2 Ho 483 1 2 Page 31 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark IEC 60317 Specific
14. 1 8 short circuit 198V 50Hz_ Fuse opened immediately Fuse current 2 2 AA 6A C123 short circuit 264V 50Hz_ Fuse opened immediately Fuse current AA C123 short circuit 198V 50Hz Fuse opened immediately Fuse current 2 6A Report reference No WT093001905 Page 38 of 49 D14 short circuit 264V 50Hz TA opened immediately Fuse current D14 short circuit 198V 50Hz Are opened immediately Fuse current i Winding temperature rise measurements Clause 13 3 TABLE Creepage distance and clearance Clause 13 4 Rated supply voltage 220 240V Pollution degree ears Material Group mb 30 N force on outside of conductive enclosure applied 0 Applied 30 N force on outside of conductive enclosure applied 0 Applied Pome vee iar pet in acl 2 Lwsnewterstsey ao zo a2 as a on an oo fes Too fers PCB trace between primary and 4 2 4 8 lt 175 secondary circuit under T1 PCB trace between primary and 7 2 lt 175 secondary circuit under U10 PCB trace between primary and secondary circuit under C48 Primary and secondary of the T1 Core and secondary of the T1 Transformer core and secondary of C133 Primary and metal enclosure Notes 1 Secondary circuits of Class Il apparatus which have connector terminals that could be earthed e g antenna signal input are subjected to the requirements for circuits conductively connected to the mains in Tables 8 and
15. 2 All tests are conducted on basic model LV6TMPVR4 to represent the others Copy of marking plate 220 240V 50 60Hz 10W Report reference No WT093001905 Page 3 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 3 GENERAL REQUIREMENTS Safety class of the apparatus cceeeeeeeee Class Il equipment 4 GENERAL CONDITIONS OF TESTS 4 1 4 Ventilation instructions require the use of the test NO tested according to the box instruction in the user s manual 5 MARKING Comprehensible and easily discernible The rating label is easily discernible Permanent durability against water and petroleum fter rubbing test by water and P spirit petroleum spirit the label still easily discernible indelible and legible 5 1 Identification maker model cceeesseeeseeees Trade mark GIEC P Model number GK B001 Class II symbol if applicable Marked on the rear enclosure P Rated supply voltage and symbol ceeeeeee 220V 240V P Frequency if safety dependant 50 60Hz P Rated current or power consumption 0 10W P 5 2 Earth terminal No earth terminal N Hazardous live terminals No hazardous live terminal N Supply output terminals other than mains No supply output terminal N 5 3 Use of triangle with exclamation mark Marked on the circuit diagram P near every critical comp
16. 4 Power cord Phino Electric HO3VVH2 F 2x0 75mm VDE 0281 5 VDE 113841 BS Co Ltd Power plug Phino Electric PHP 318 250V 13A BS 1363 Part KM 69214 BS Company Limited 1 A1 A2 Fuse in BS plug Dongguan TDC 180 240V 3A BS ASTA 658 Cooper 1362 A1 A2 Electrionics Co Limited Taller GmbH ATLAS 240V 3A BS KM70570 1362 A1 A2 Connector CN6 Zhejiang Jinda VH 3A2 7 8MM UL 1977 UL E237523 Electronics Co Ltd X2 capacitor Tenta Electric IEC 60384 14 VDE 119119 alt Shenzhen IEC 60384 14 VDE 123934 Shengxin MEX X2 0 1uF 280VAC Capacitor Co Ltd Y1 capacitor Suan Tai 1000pF 400VAC IEC 60384 14 VDE118413 y1 C31 C48 amp Electronics CY C33 Co Ltd Shantou High 1000pF 400VAC IEC 60384 14 VDE118413 New Y1 Technology Dev Zone CD Songtian Enterprise Co Ltd XC 3T T630mA L250V EN 60127 1 VDE EN 60127 2 A091961 Electronics Shen Report reference No WT093001905 Page 41 of 49 zhen Corp Ltd Test in unit Line filter LF1 Hua Yu Electrical UU9 8 85mH EN 60065 Factory Transformer T1 Hua Yu Electrical EE25 Class B EN 60065 Factory Primary Wire TAI I ELECTRIC UEW 130 C UL 1446 WIRE amp CABLE CO LTD Bobbin Chang Chun T375J 150 C V 0 UL 94 Plastic Co Ltd Insulation tape JINGJIANG CT280 130 C UL 510 UL E165111 YAHUA PRESSURE SENSITIVE GLUE CO LTD Tube Changyuan CB TT T 600V 200 C UL 224 UL E180908 Electronics Shenzhen Co Ltd Triple i
17. 400 Subclause 5 3 2 corrigendum 1 Add after the fourth dash NOTE In Finland Norway and Sweden exclusions are applicable for equipment which is intended for connection to the building installation wiring using screw terminals or other reliable means and for equipment which is intended for Report reference No WT093001905 Page 28 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark connection to the building installation wiring via an industrial plug and socket outlet or an appliance coupler or both complying with EN 60309 or with a comparable national standard S SE 14 The following is added Switches containing mercury such as thermostats relays and level controllers are not allowed Justification Ordinance 1990 944 on Prohibition in Connection with Handling Importation and Exportation of Chemical Products Certain Cases C Delete the note C Delete the notes of Table J 1 J 2 After Table J 1 the following is added In Norway due to the IT power distribution system used the a c MAINS supply voltage is considered to be equal to the line to line voltage and will remain 230 V in case of a single earth fault Justification Based on a use in Norway of an IT power distribution system where the neutral is not provided Annex N C Add after the introduction For ROUTINE TEST reference is made to EN 50333 Bibliograph C Add the following standards y EN 50332 1 2000 Sound system equipm
18. B 14 10 Batteries No battery used Zz 14 10 1 Batteries mounted with no risk of accumulation of N flammable gases 14 10 2 No possibility of recharging non rechargeable N batteries 14 10 3 Recharging currents and times within N manufacturers limits Lithium batteries discharge and reverse currents N within the manufacturers limits 14 10 4 Battery mould stress relief 14 10 5 Battery drop test 14 11 Optocouplers Separately approved Optocouplers comply with Cl 8 UVUsl UVU UVUIZ 2 Internal and external dimensions to 13 1 or alternatively 13 6 jointed insulation Zz 14 12 Surge suppression varistors No surge suppression varistor Comply with IEC 61051 2 Not connected between mains and accessible parts except for earthed parts of permanently connected apparatus Complies with the current pulse fire hazard and N thermal stress requirements of 14 12 15 TERMINALS 15 1 1 Mains plug appliance inlet interconnection Mains plug separately couplers and mains socket outlet meet the approved according to the appropriate standard appropriate standard Report reference No WT093001905 Page 14 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark Overloading of plugs or appliance inlets prevented if the apparatus has mains socket outlets No mains socket outlet Overloading of internal wiring prevented if the apparatus ha
19. LVD TEST REPORT For DVB T Receiver Model Number LV6TMPVR4 CE Report Number WT093001905 Test Laboratory Shenzhen Academy of Metrology and Quality Inspection Site Location Bldg Metrology and Quality Inspection Longzhu Road Shenzhen Guangdong China Tel 0086 755 26941636 Fax 0086 755 26941538 Website gt WWw smq com cn Report reference No WT093001905 Page 1 of 49 TEST REPORT EN 60 065 Audio video and similar electronic apparatus Safety requirements Report Reference No WT093001905 Tested by signature Jolly Gu Checked by signature 0 00 0 Flora Lee Approved by signature gt Alvin An LAS CLISSUG anpi 2009 09 14 Testing laboratory Name Shenzhen Academy of Metrology and Quality Inspection PONG PERETE TETTETETT Bldg Metrology amp Quality Inspection Longzhu Road Shenzhen Guangdong China Testing OCA iseia Shenzhen Academy of Metrology and Quality Inspection Client Nama znana LIFEVIEW SRL POROS unana Via Dell Economia 11 31033 Castelfranco Veneto TV Italy Standard aan aAA EN 60065 2002 A1 2006 TOODA nonan y GE Non standard test method gt NA Test item Description DVB T Receiver TINOMANA NOTONLYTV Model and or type reference gt LV6TMPVR4 Manulsctireres ik es gt LIFEVIEW SRL BREN OPPRESSA EEEE T E T gt 220 240V 50 60Hz 10W Test
20. See clause 14 P 20 1 2 and 20 1 3 other than fire enclosures mounted nearer to a potential ignition source than the distances in Table 21 comply with the relevant flammability category in Table 21 Components and parts as above but shielded from N a potential ignition source with the barrier area in accordance with Table 21 and fig 13 20 2 Fire enclosure N 20 2 1 Potential ignition sources with open circuit voltage NO voltage gt 4 kV N gt 4 kV peak a c or d c contained in a fire enclosure to V 1 20 2 2 Internal fire enclosures with openings not No internal fire enclosure N exceeding 1 mm in width and with openings for wires completely filled 20 2 3 Requirements of 20 2 1 and 20 2 2 met by an N internal fire enclosure Report reference No WT093001905 Page 19 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark A APPENDIX A ADDITIONAL REQUIREMENTS FOR APPARATUS WITH N PROTECTION AGAINST SPLASHING WATER A 5 1 j Marked with IPX4 IEC 60529 5 4 1 a does not N apply A 10 2 1 Enclosure provides protection against splashing N water A 10 2 2 Humidity treatment carried out for 7 days N APPENDIX B APPARATUS TO BE CONNECTED TO THE N TELECOMMUNICATION NETWORKS Complies with IEC 62151 clause 1 Complies with IEC 62151 clause 2 modified in accordance with annex B of this standard Complies with IEC 62151 clause 6 Complies wi
21. act is required according to the wiring rules shall be provided with a plug in accordance with the Heavy Current Regulations Section Report reference No WT093001905 Page 24 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 107 2 D1 standard sheet DK 2 1a To the second paragraph the following is added Socket outlets intended for providing power to CLASS II apparatus with a rated current of 2 5 A shall have the following dimensions Dimensions in mm Other dimensions shall be in compliance with the Heavy Current Regulations Section 107 2 D1 Standard Sheet DKA 1 3 for portable socket outlets Shutters are not required To the third paragraph the following is added Mains socket outlets with earthing contact shall be in compliance with Heavy Current Regulations Section 107 2 D1 Standard sheet DK 1 3a DK 1 5a or DK 1 7a Justification Heavy Current Regulations Section 107 Report reference No WT093001905 Page 25 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark S NO No socket outlets Mains socket outlets mounted on CLASS II apparatus shall comply with the specifications given in CEE Publ 7 as far as applicable with the following amendments 8 Dimensions a 2 5 A 250 V two pole socket outlets for electronic apparatus shall comply with the enclosed Standard Sheet I Other dimensions according ta CEE Publication 7 Standard Sheet Portable Single Way Sookbet O
22. an table 5 permits compliance with IEC 60 384 1 4 38 category B or better a e Shielded by a barrier acc to 20 1 4 table 21 or metal e E on ao 14 3 Inductors and windings Comply with IEC 61558 1 IEC 61558 2 as relevant and clause 20 1 4 Tested with the equipment 14 3 1 Transformers and inductors marked with manufacturer s name and type eee eeeeeeeeeeee Marked with the code Transformers and inductors separately approved Tested in unit 14 3 2 General Insulation material complies with clause 20 1 4 Refer to 20 1 4 14 3 3 Constructional requirements 14 3 3 1 Clearances and creepage distances comply with clause 13 See clause 13 U U0 U0 U0 2 14 3 3 2 Transformers meet the constructional requirements 14 3 4 1 Class II transformers have adequate separation between hazardous live parts and accessible parts double or reinforced insulation Primary separately from secondary coil by reinforced insulation Report reference No WT093001905 Page 11 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark Coil formers and partition walls gt 0 4 mm Bobbin of T1 gt 0 9 mm 14 3 4 2 Class transformers with basic insulation and protective screening only if all 7 conditions of 14 3 4 2 are met Class II transformer 14 3 4 3 Separating transformers with at least basic
23. are measured Opening block 264V 50Hz Work until got steady state No excessive Transformer T1 coil 52 2K temperature rise No hazard Test last for 2h PCB 75 4K Enclosure metal 17 3K Enclosure plastic 13 2K USB overload 264V 50Hz Overload to 0 3A input current 76mA input Transformer T1 coil 52 5K power 8 62W Work until got steady state No excessive temperature rise No hazard Test PCB 85 2K last for 1 5h Enclosure metal 13 6K Enclosure plastic 9 1K USB short circuit 264V 50Hz_ Input current 55mA input power 6 17W Work until got steady state No excessive Transformer T1 coil 40 6K temperature rise No hazard Test last for 2h PCB 64 3K Enclosure metal 9 8K Enclosure plastic 5 6K E45 short circuit 264V 50Hz_ Input current 22 46mA input power 0 19 1 23W Circuit protected Unit shut down immediately No hazard Test last for 15min D19 short circuit 264V 50Hz_ nput current 22mA input power 0 32W Circuit protected Unit shut down immediately No hazard Test last for 15min U10 pin3 4 short circuit 264V 50Hz_ nput current 22mA input power 0 29W Circuit protected Unit shut down immediately No hazard Test last for 15min U10 pin1 2 short circuit 264V 50Hz_ Input current 22 41mA input power 0 32 1 27W Circuit protected Unit shut down immediately No hazard Test last for 15min U9 pin1 8 short circuit 264V 50Hz_ Fuse opened immediately Fuse current 2 U9 pin
24. ations for particular types of winding EN 60317 wires IEG 60320 Appliance couplers for household ard EM 60220 similar general purposes IES 69338 1 med Safety of household and similar electrical EN 60338 1 Al appliances Ad Parn 1 General requirements AT IEG J354 1 imod 1 Fixed capacibors for use in electronic EN 60334 1 equipment Parl 1 Generie spechication IEG 69354 14 Fixed capacitors for use in elecironiz EM 132400 AT equipment Parl 14 Sectional specification Fixed capacitors lor slechhomagnetic nlerference suppression and connection bo the supply mains IEG Boa Graphical sinbal for Wee on equipment IEG 60454 Spedicalons for pressure sersiiwe adhesive tapes for electrical purposes IEC J529 Degrees of protection provided by encloaures IP Code Al IEG BOBBS 1 Insulation soordination for equipment within AT low voltage systema AD Fari 1 Principles r quiremenis and eais Report reference No WT093001905 Page 32 of 49 IEG BOGRE 3 IEC 60641 IEC 0685 2 2 IEC 8895 11 10 At IEG BOrOr IEC 60730 read IEC 60825 1 con December Al A IEG 60851 IEG BORG IEG 60865 1 IEC Boo08 IEG BOSD mcd can January IEC jap IEC BORSE 2 2 med Report reference No WT093001905 EN 60065 2002 A1 2006 Insulation coordination for equipment wither low voltage systems Pan 3 ee of coaglings to achieve inaulation coordination of printed board assemblies Thermal links
25. case verdicts Test case does not apply to the test object NCA Test item does meet the requirement 0 00 0 00 P ass Test item does not meet the requirement F ail Testing Date of receipt of test iteM 2 0 0 eeeeeees 2009 08 27 Date s of performance of test 2009 08 08 to 2009 09 04 Report reference No WT093001905 Page 2 of 49 General remarks This report shall not be reproduced except in full without the written approval of the testing laboratory The test results presented in this report relate only to the item s tested see appended table refers to a table appended to the report see remark refers to a remark appended to the report see Annex refers to an annex appended to the report Throughout this report a period coma is used as the decimal separator Factory and address LIFEVIEW SRL Via Dell Economia 11 31033 Castelfranco Veneto TV Italy General product information 1 This report covers models LV6TMPVR4 The LV6TMPVR4 is considered as basic model All other models are the same as model LV6TMPVR4 in circuit diagram construction and critical safety components The differences between other models and the basic model are the color and the decoration of the enclsoure and the model number due to different client Summary of Testing and Conclusions 1 The sample s tested complies with the requirements of EN 60065 2002 A1 2006
26. corners not hazardous Edges and corners are P smoothed 19 5 Glass surfaces exc laminated with an area No glass surface N exceeding 0 1 m or maximum dimension gt 450 mm pass the test of 19 5 1 19 6 Wall or ceiling mountings adequate N 20 RESISTANCE TO FIRE 20 1 Electrical components and mechanical parts Report reference No WT093001905 Page 18 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark a Exemption for components contained in an N enclosure of material V O to IEC 60707 with openings not exceeding 1 mm in width b Exemption for small components as defined in Some small components P 20 1 mounted on UL listed PCB with flammability of V 0 20 1 1 Electrical components meet the requirements of Considered complied for P Clause 14 or 20 1 4 adapter itself 20 1 2 Insulation of internal wiring working at voltages Internal wiring working at N gt 4 kV or leaving an internal fire enclosure not voltages not exceeding 4kV contributing to the spread of fire 20 1 3 Material of printed circuit boards on which the V 0 PCB used P available power exceeds 15 W at a voltage between 50 V and 400V peak a c or d c meets V 1 or better to IEC60707 unless used in a fire enclosure Material of printed circuit boards on which the See above P available power exceeds 15 W at a voltage gt 400 V peak a c or d c meets V 0 to IEC 60707 20 1 4 Components and parts not covered by 20 1 1
27. d nuts clamping conductors have adequate threads ISO 261 ISO 262 or similar 15 3 4 Soldered conductors wrapped around terminal prior to soldering or held in place by additional means Clamping of conductor and insulation if not soldered or held by screws Report reference No WT093001905 Page 15 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 15 3 5 Terminals allow connection of appropriate cross N sectional area of conductors for the rated current of the equipment 15 3 6 Terminals to 15 3 3 have sizes required by N table 16 15 3 7 Terminals clamp conductors between metal and N have adequate pressure Terminals designed to avoid conductor slipping out N when tightened or loosened Terminals adequately fixed to avoid loosening N when the clamping is tightened or loosened and stress on internal wiring is avoided 15 3 8 Terminals carrying a current more than 0 2 A N contact pressure not transmitted by insulating material except ceramic 15 3 9 Termination of non detachable cords wires P terminated near to each other Terminals located and shielded test with 8 mm N strand 15 4 Devices forming a part of the mains plug Not direct plug in equipment N 15 4 1 No undue strain on mains socket outlets N 15 4 2 Device complies with standard for dimensions of mains plugs 15 4 3 Device has adequate mechanical strength tests N a b c
28. ent Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 1 General method for one package equipment EN 50332 2 2003 Sound system equiment Headphones and earphones associated with portable audio equipemnt Maximum sound pressure level measurement method and limit considerations Part 1 General method for one package equipemnt EN 50332 1 2003 Sound system equipment headphones and earphones associated with portable audio equipment Maximum sound pressure level measruement Maximum sound pressure level measurement methodology and limit consideration Part 2 Matching of sets with headphones if either or both are offered separately EN 60065 2002 A1 2006 Add the following notes for the standards indicated Report reference No WT093001905 Page 29 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark IEC 60130 all parts NOTE Parts 9 and 17 1998 are harmonized as ENs not modified IEC 60169 all parts NOTE Partly harmonized in the EN 60169 HD 134 series not modified IEC 60173 1964 NOTE Harmonized as HD 27 1 1978 not modified IEC 60335 2 56 1997 NOTE Harmonized as EN 60335 2 56 1997 not modified IEC 60335 2 82 1999 NOTE Harmonized as EN 60335 2 82 2000 not modified IEC 60410 1973 NOTE Harmonized as EN 61040 1992 not modified IEC 60695 all parts NOTE Harmonized as EN 60695
29. ent Not class equipment N Report reference No WT093001905 Page 5 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark Basic insulation between hazardous live parts and earthed accessible parts Resistors bridging basic insulation complying with 14 1 a 8 6 Class Il equipment and Class II constructions within Class equipment Reinforced or double insulation between Reinforced or double insulation hazardous live parts and accessible parts between hazardous live part and accessible parts Components bridging reinforced or double Transformer T1 bridging insulation complying with 14 1 a or 14 3 primary and secondary circuit complying with 14 3 Basic and supplementary insulation each being No such capacitor used bridged by a capacitor complying with 14 2 1 a Reinforced or double insulation being bridged with No such capacitor used 2 capacitors in series complying with 14 2 1 a Reinforced or double insulation being bridged with Y1 capacitor separately a single capacitor complying with 14 2 1 b approved used Basic insulation bridged by components complying Not used with 14 3 4 3 8 8 Basic or supplementary insulation gt 0 4 mm mm The insulation of the primary wire 0 4mm 0 42mm Reinforced insulation gt 0 4 mm mm s Enclosure plastic 2 3mm min Thin sheet insulation excluding non separable thin sheet insulation See 8 22 Basic or supplem
30. entary insulation at least two layers each meeting 10 3 Basic or supplementary insulation three layers any two of which meet 10 3 Reinforced insulation two layers each of which meet 10 3 Reinforced insulation three layers any two which meet 10 3 8 9 Adequate insulation between internal hazardous Primary internal wire separate live conductors and accessible parts from accessible parts by double insulation Adequate insulation between internal hazardous live parts and conductors connected to accessible parts Internal hazardous live parts separate form conductors connectors connected to accessible part by double insulation Report reference No WT093001905 Page 6 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 8 10 Double insulation between conductors connected Double insulation used P to the mains and accessible parts Double insulation between internal hazardous live parts and conductors connected to accessible parts 8 11 Detaching of wires Wires are well secured No P wire is likely to become detached No undue reduction of creepages or clearance See above N distances if wires become detached Vibration test carried Out cceccecccsccessesseseeeeeseers See 12 1 2 8 13 Adequate fastening of windows lenses lamp No such part covers etc pull test 20 N for 10 s 8 14 Adequate fastening of cov
31. ers pull test 50 N for P 10 s 8 15 No risk of damage to the insulation of internal Internal wire well secured and P wiring due to hot parts or sharp edges not likely to touch the hot parts or sharp edge 8 16 Only special supply equipment can be used Not such equipment 8 17 Insulated winding wire without additional Triple insulation wire used as interleaved insulation the secondary coil of the transformer 8 18 Endurance test as required by 8 17 The triple insulation wire has N been separately approved 8 19 Disconnection from the mains See below 8 19 1 Disconnect device Power plug used as disconnect device All pole switch or circuit breaker with gt 3mm No switch N contact separation 8 19 2 Mains switch ON indication N 8 20 Switch not fitted in the mains cord N 8 21 Bridging components comply with clause 14 No such component used N 8 22 Non separable thin sheet material No such material used N 9 ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS P 9 1 Testing on the outside P 9 1 1 For voltages gt 1000 V ac or gt 1500 V dc complies No voltage gt 1000 V ac or with clause 13 3 1 for basic insulation gt 1500 V dc 9 1 1 1 a Open circuit voltages b Touch current measured from terminal devices Results in appended table using the network in annex D sss 9 1 1 The measuring network according to annex D Report reference No WT093001905 Page 7 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark
32. exceeding the limits of table 3 by max 100 K for xceed the limits of table 3 max 5 min a Temperature rise of printed circuit boards PCB N to 20 1 3 exceeding the limits of table 3 by not more than 100 K for an area not greater than 2 cm b Temperature rise of printed circuit boards PCB N to 20 1 3 up to 300 K for an area not greater than 2 cm for a maximum of 5 min Meets all the special conditions if conductors on N printed circuit boards are interrupted Class protective earthing maintained Not class equipment 11 2 4 Temperature rise of parts acting as a support or see appended table P mechanical barrier 11 2 5 Temperature rise of windings see appended table 11 2 6 Temperature rise of parts not subject to the limits see appended table P of 11 2 1 to 11 2 5 12 MECHANICAL STRENGTH P 12 1 1 Bump test where mass gt 7 kg Less than 7 kg N 12 1 2 Vibration test No damage P 12 1 3 Impact hammer test 0 5J three times No damage P Steel ball test 2J on top side back and front P enclosure No damage 12 1 4 Drop test for portable apparatus where mass lt 7 Not portable apparatus N kg 12 1 5 Thermoplastic enclosures strain relief test 70 C for 7h No hazard live part P become accessible Report reference No WT093001905 Page 9 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark
33. f the apparatus a notice in German language that produced X rays are sufficiently shielded by the intrinsically safe cathode ray tube In case of approval of the whole TV receiver with an accelerating voltage exceeding 20 kV On the outer of the apparatus the licence number R6 and the following text Die in diesem Gerat entstehende Rontgenstrahlung ist ausreichend abgeschirmt Beschleunigungsspannung max KV Supplied with the apparatus a copy of the Zulassungsschein together with the notices required there In case of TV receivers with accelerating voltages not exceeding 20 kV Die in diesem Gerat entstehende Rontgenstrahlung ist ausreichend abgeschirmt Beschleunigungsspannung max KV Justification German ministerial decree against ionizing radiation R6ntgenverordnung dated 1987 01 08 NOTE The German ministerial decree Rontgenverordnung is under revision S DE No cathode ray tube Annex ZC Delete the A deviation for Clause 5 for Germany and add the following new A deviation Clause National deviation Germany Report reference No WT093001905 Page 22 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 6 1 The following requirement applies For the operation of the any cathode ray tube intended for the display of visual images Operating at an acceleration voltage exceeding 40kV authorization is required or Application of type approval Ba
34. fault conditions 7 HEATING UNDER NORMAL OPERATING CONDITIONS 7 1 Temperature rises not exceeding specified values See appended table no operation of fuse links 7 1 1 Temperature rise of accessible parts see appended table 7 1 2 Temperature rise of parts providing electrical see appended table insulation 7 1 3 Temperature rise of parts acting as a support or as N a mechanical barrier 7 1 4 Temperature rise of windings see appended table 7 1 5 Parts not subject to a limit under 7 1 1 to 7 1 4 see appended table 7 2 Softening temperature of insulating material The input current was less supporting parts conductively connected to the than 0 2A mains carrying a current gt 0 2 A at least 150 C 8 CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION P AGAINST ELECTRIC SHOCK 8 1 Conductive parts covered by lacquer paper Compliance checked by P untreated textile oxide films and beads etc inspection considered to be bare 8 2 No shock hazard when changing voltage setting NO voltage setting device It is N device fuse links or handling drawers etc not possible for user to access fuse links No indicators and drawers used 8 3 Insulation of hazardous live parts not provided by No hygroscopic material used P hygroscopic material as insulation 8 4 No risk of electric shock following the removal of a There is no risk of an electric P cover which can be removed by hand shock from accessible parts 8 5 Class equipm
35. fore earth conductor 16 6 Apertures for external flexible cord no risk of P damage to the cord during assembly or movement in use 16 7 Transportable musical instruments and amplifiers NOt transportable musical N fitted with detachable cord set with appliance inlet instrument to IEC 60320 1 Transportable musical instruments and amplifiers N fitted with detachable cord sets or with means of stowage to protect the cord 17 ELECTRICAL CONNECTIONS AND MECHANICAL FIXINGS 17 1 Torque test to table 20 screws into metal 5 times Enclosure fixing and PCB fixing screws 3 0mm tested with 0 5Nm torque screws into non metallic material 10 times 17 2 Correct introduction into female threads in non metallic material 17 3 Cover fixing screws captive No captive screw used Non captive fixing screws no hazard when No clearance and creepage replaced by a screw whose length is 10 times its distance will reduce to below diameter the requirement 17 4 No loosening of conductive parts carrying a current N gt 0 2A 17 5 Contact pressure not transmitted through plastic N other than ceramic for connections carrying a current gt 0 2 A 17 6 Stranded conductors of flexible supply cords N carrying a current gt 0 2 A with screw terminals not consolidated by solder 17 7 Cover fixing devices other than screws have No cover N adequate strength and their positioning is unambiguous
36. insulation No separating transformer 14 3 5 1 Class II transformers have adequate insulation between hazardous live parts and accessible parts double or reinforced insulation Primary separately from secondary coil by reinforced insulation Coil formers and partition walls gt 0 4 mm Bobbin of T1 gt 0 9 mm 14 3 5 2 Class transformers have adequate insulation between hazardous live parts and accessible conductive parts or those conductive parts or protective screens connected to a protective earth terminal Winding wires connected to protective earth have adequate current carrying capacity 14 4 High voltage components No high voltage component High voltage components and assemblies U gt 4 kV peak separately approved Component meets category V 1 of IEC 60707 14 4 1 High voltage transformers and multipliers tested as part of the submission 14 4 2 High voltage assemblies and other parts tested as part of the submission 14 5 Protective devices Protective devices used within their ratings External clearances and creepage distances meet requirement of clause 13 for the voltage across the device when opened See clause 13 14 5 1 1 a Thermal cut outs separately approved No thermal cut out b Thermal cut outs tested as part of the submission Zz 14 5 1 2 a Thermal links separately approved No thermal link b Thermal lin
37. istance through insulation of at least 0 4 mm which shall pass the electric strength test below If this insulation forms part of a semiconductor component e g an optocoupler there is no distance through insulation requirement for the insulation consisting of an insulating compound completely filling the casing so that CLEARANCES and CREEPAGE DISTANCES do not exist if the component passes the electric strength test in the accordance with the compliance clause below and in addition e passes the test and inspection criteria of 13 6 with an electric strength test of 10 3 using the test voltage of 1 5 kV multiplied by 1 6 and e is subject to routine testing for electric strength during manufacturing using a test voltage of 1 5 kV for performance of the test see N 2 1 It is permitted to bridge this insulation with a capacitor complying with EN 132400 1994 subclass Y2 A capacitor classified Y3 according to EN 132400 1994 may bridge this insulation under the following conditions e the insulation requirements are satisfied by having a capacitor classified Y3 as defined by EN 132400 which in addition to the Y3 testing is tested with an impulse test of 2 5 kV defined in IEC 62151 Subclause 6 2 1 e the additional testing shall be performed on all the test specimens as described in EN 132400 e the impulse test of 2 5 kV is to be performed before the endurance test in EN 132400 in the sequence of tests as described in EN 132
38. ks tested as part of the submission 14 5 1 3 Thermal devices re settable by soldering No such device 14 5 2 1 Fuse links in the mains circuit according to IEC 60127 Fuse link separately approved Viz 2 2 14 5 2 2 Correct marking of fuse links adjacent to holder T 630mMAL250V marked near the fuse link on the PCB board 14 5 2 3 Not possible to connect fuses in parallel Report reference No WT093001905 Page 12 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 14 5 2 4 Not possible to touch hazardous live parts when Tools need to replace the fuse N replacing fuse links without the use of a tool link 14 5 3 PTC S thermistors comply with IEC 60730 1 No PTC S thermistor PTC S devices 15 W category V 1 or better 14 5 4 Circuit protectors have adequate breaking capacity and their position is correctly marked 14 6 Switches No switch 14 6 1 a Separate testing to IEC 61058 including 10 000 operations Normal pollution suitability Resistance to heat and fire level 3 and Make and break speed independent of speed of actuation V 0 compliance with annex G G 1 1 14 6 1 b Tested in the apparatus N Switch controlling gt 0 2A with open contact N voltage gt 35 V peak 24 V dc complying with 14 6 3 14 6 4 and V 0 in annex G G 1 1 Switch controlling gt 0 2A with open contact N vo
39. least 2 MQ min after Surge test with 50 discharges surge test for basic and 4 MQ min for reinforced at a rate of maximum 12 min Wel kel lela ania a a aE from a 1nF capacitor charged to 10 kV performed Measured greater than 4M between the circuit connect to hazards parts and circuit not connect to hazards parts 10 2 Humidity treatment 48 h or 120 h essesi gt 48h 10 3 Insulation resistance and dielectric strength between mains terminals Insulation Resistance and dielectric strength N across BASIC or SUPPLEMENTARY insulation Class 1 Insulation resistance and dielectric strength across see appended table P Report reference No WT093001905 Page 8 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 11 FAULT CONDITIONS 11 1 No shock hazard under fault condition No electric shock during fault operation 11 2 Heating under fault condition No excessive temperature P No hazard from softening solder o ea softened during the est Flames extinguish within 10 seconds No flames in fault condition P tests Soldered terminations not used as protective P mechanism 11 2 1 Measurement of temperature rises see appended table 11 2 2 Temperature rise of accessible parts see appended table 11 2 3 Temperature rise of parts other than windings see appended table providing electrical insulation Temperature rise of printed circuit boards PCB PCB temperature rise didn t N
40. ltage lt 35 V peak 24 V dc complying with 14 6 3 and V 0 in annex G G 1 1 Switch controlling lt 0 2A with open contact N voltage gt 35 V peak 24 V dc complying with 14 6 4 and V 0 in annex G G 1 1 14 6 2 Switch tested to 14 6 1 b constructed to IEC N 61058 1 subclause 13 1 and has making breaking action independent of speed of actuation 14 6 3 Switch tested to 14 6 1 b compliant with IEC N 61058 1 subclause 16 2 2 d and m not attaining excessive temperatures in use 14 6 4 Switch tested to 14 6 1 b has adequate dielectric N strength 14 6 5 Mains switch controlling mains socket outlets N additional tests to IEC 60058 1 Socket outlet current marking correct No socket outlet 14 7 Safety interlocks No such devices Safety interlocks to 2 8 of IEC 60950 ZiZz 2 2 14 8 Voltage setting devices and the like No such devices Report reference No WT093001905 Page 13 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark Voltage setting device not likely to be changed N accidentally 14 9 Motors No motor 14 9 1 Endurance test on motors Motor start test Dielectric strength test 14 9 2 Not adversely affected by oil or grease etc 14 9 3 Protection against moving parts ZiZz Z2 Z2 2 2 2 14 9 4 Motors with phase shifting capacitors three phase motors and series motors meet clause B 8 B 9 and B 10 of IEC 60950 Annex
41. nsulated SHANGHAI GPX B 130 C UL 60950 1 UL E243712 wire CHUANYE ELECTRONIC TECHNOLOGY CO LTD Optocoupler U10 Bright LED BPC 817B Reinforce EN 60747 5 2 Electronics Corp insulation alt Sharp Corp PC817 Reinforce EN 60747 5 2 Electronics insulation Components Group Circuit Board Mfr Plastic enclosure Formosa AG15A HB Chemicals amp Fibre Corp Plastics Div Heat shrinkable CHANGYUAN CB HFT 300V 125 C UL 224 tube ELECTRONICS SHENZHEN CO LTD at soov 125 C A Test in unit UL E85640 UL E59481 Cc i VDE 40007240 VDE 40008087 UL E193079 UL E162823 UL E180908 Cc C C m aa m oO o1 A gt ar i Report reference No WT093001905 Page 42 of 49 Annex 1 Photo Document ips jarn temmu 0 Photo 3 Enclosure Photo 4 Inside Report reference No WT093001905 Page 43 of 49 Annex 1 Photo Document PO hath nal pa ee ee ppp La Photo 6 Power supply and function board Report reference No WT093001905 Page 44 of 49 Annex 1 Photo Document Photo 1 Top view Photo 2 Bottom view Report reference No WT093001905 Page 45 of 49 Annex 1 Photo Document Transformer T1 _ m Y fi apat E a Photo 6 fourth layer Photo 7 fifth laye Report reference No WT093001905 Page 46 of 49
42. onents 5 4 Instructions for use Instruction for use provided in P user s manual in English 5 4 1 Mains powered equipment not exposed to dripping Stated in the user s manual P or splashing Warning concerning objects filled with liquid etc Hazardous live terminals instructions for wiring No hazardous live terminals N Instructions for replacing lithium battery No battery N Instructions for modem if fitted No modem provided N Class earth connection warning Not class equipment N Instructions for multimedia system connection N Special stability warning for fixed installation Not fixed installation N Warning battery exposure to heat No battery N Warning protective film on CRT face No CRT N Report reference No WT093001905 Page 4 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark 5 4 2 Disconnect device plug coupler or all pole mains POower plug used as P switch location accessibility and markings disconnect device Instructions for permanently connected equipment Not permanently connected N equipment 6 HAZARDOUS RADIATION N 6 1 lonizing radiation lt 36 pA kg 0 5 mR h No ionizing radiation 6 1 European Council Directive 96 29 Euratom of 13 May 1996 10cm from outer surface of apparatus Eee lt 1uSv h 0 1mR h 6 2 Laser radiation emission limits to IEC 60825 1 No laser radiation Emission limits under
43. s mains socket outlets No mains socket outlet 15 1 2 Connectors for antenna earth audio video or data No risk of insertion in mains socket outlets None of mismatch of connectors to AC mains occurred No risk of insertion into audio or video outlets marked with the symbol of 5 2 No sockets indicated with the symbol 15 1 3 Output terminals of a c adaptors or similar devices not compatible with household mains socket outlets No such device 15 2 Provision for protective earthing Accessible conductive parts of Class equipment reliably connected to earth terminal within equipment Class Il equipment Protective earth conductors correctly coloured Equipment with non detachable mains cord provided with separate protective earth terminal near mains input Protective earth terminal resistant to corrosion Earth resistance test lt 0 1 Q at 25 A ww 15 3 Terminals for external flexible cords and for permanent connection to the mains supply 15 3 1 Adequate terminals for connection of permanent wiring Not permanent connected equipment 15 3 2 Reliable connection of non detachable cords Not soldered to conductors of a printed circuit board Adequate clearances and creepage distances between connections should a wire break away No wire is likely to break away Wire secured by additional means to the conductor 15 3 3 Screws an
44. th IEC 62151 clause 7 Complies with IEC 62151 annex A B and C APPENDIX L ADDITIONAL REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES Marking and Instructions Terminals to connection to synchroniser not HAZARDOUS LIVE Lithium batteries meet permissible temp rise in Table 3 unless comply with 6 3 2 of IEC 60086 4 Mains switch characteristics appropriate to its function under normal conditions N N N N Complies with IEC 62151 cause 5 but with 5 3 1 N N N N Complies with IEC 62151 clause 3 but with 3 5 4 modified to 2 4 10 of this standard Complies with IEC 62151 clause 4 but with 4 1 2 4 1 3 and 4 2 1 2 modified in accordance with annex B of this standard N N N N Report reference No WT093001905 Page 20 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark GROUP DIFFERENCES CENELEC common modifications and special national conditions according to CB Bulletin No 112A December 2006 EN 60065 2002 A1 2006 IEC Publication 60065 2001 A1 2005 EXPLANATION FOR ABBREVIATIONS C CENELEC common modification S Special national conditon P Pass F Fail N A Not applicable Placed in the column to the right ONTENT Add the following annexes Annex ZA normative Other international publications quoted in this standard with the references of the relevant European publications Annex ZB normative Special national conditions Annex ZC informative A deviations 2 6 1 S DK Class II
45. uartzulassung and marking Justification German ministerial decree against ionizing radiation R6ntgenverordnung in force since 2002 07 01 implementing the European Directive 96 29 EURATOM NOTE Contact address Physikalisch Tchnische Bundesanstalt Bundesallee 100 D 38116 Braunschweig Tel Int 49 513 592 6320 Internet http www ptb de 5 1 IT additional marking on the outside of the TV receiver in Not TV receiver N Italian language IT user instructions in Italian language including a ae declaration P IT certificatino number on the back cover number on the back cover C Replaced the note by NOTE For RATED POWER CONSUMPTION measurements of TVs reference is made to EN 62087 Measurements are done in the ON play operating mode C Add the following indent No earphone or headphone Za A warning that excessive sound pressure from earphones and headphones can cause hearing loss Report reference No WT093001905 Page 23 of 49 EN aa OO 2006 Clause e Requirement Test sd Test C Replace the subclause by 6 1 lonizing radiation Equipment that might produce ionizing radiation is checked by measuring the amount of radiation The amount of radiation is determined by means of a radiation monitor of the ionizing chamber type with an effective area of 1000m2 or by measuring equipment of other types giving equivalent result Measurements are made with the equipment on test operating at the most unfa
46. utas till jordat uttag Subclause 4 1 4 corrrigendum 1 Add at the end of the subclause NOTE In Norway for requirements see 4 1 1 note and 5 3 1 note 1 Subclause 4 2 1 2 corrigendum 1 Add at the end of the subclause NOTE 3 In Norway for requirements see 5 3 1 note 1 Subclause 4 2 1 3 corrigendum 2 Add at the end of the subclause NOTE In Norway for requirements see 4 1 1 note and 5 3 1 note 1 Subclause 4 2 1 4 corrigendum 1 Number the existing note as NOTE 1 and add at the end of the subclause the following NOTE 2 NOTE 2 In Norway for requirements see 4 1 1 note and 5 3 1 note 1 Subclause 5 3 1 corrigendum 1 Add after the first test specifications paragraph NOTE 1 In Finland Norway and Sweden there are additional requirements for the insulation Renumber the existing note as NOTE 2 Report reference No WT093001905 Page 27 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark For additional requirements for the insulation in Finland Norway and Sweden in NOTE 1 the following text is added between the first and the second paragraph this text is identical to the corresponding EN 60950 1 2001 NOTE 1 In Finland Norway and Sweden if this insulation is solid including insulation forming part of a component it shall at least consist of either e two layers of thin sheet material each of which shall pass the electric strength test below or one layer having a d
47. utlets 24 Mechanical strength a 2 5 A 250 V socket outlets for CLASS II electronic apparatus are tested as specified in 12 1 3 of EN 60065 Also the protecting rim shall be tested Justification Act of 24 May 1929 relating to supervision of electrical installation TEA 1929 FEL 1998 C Replace not 1 by In the CENELEC countries listed in IEC 62151 special national conditons apply Add the following All subclauses given below are subclauses of IEC 62151 Report reference No WT093001905 Page 26 of 49 EN 60065 2002 A1 2006 Requirement Test Result Remark ref corrigenda 1 and 2 to IEC 62151 Subclause 4 1 1 corrigendum 2 Add after the first paragraph NOTE In Finland Norway and Sweden CLASS equipment which is intended for connection to the building installation via a non industrial plug or a non industrial appliance coupler or both and in addition is intended for connection to other equipment or a network shall if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and ACCESSIBLE parts has a marking stating that the equipment must be connected to an earthed mains socket outlet The marking text in the applicable countries shall be as follows In Finland Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan In Norway Apparatet ma tilkoples jordet stikkontakt In Sweden Apparaten skall ansl
48. vourable supply voltage see 4 2 and with operator controls and service controls adjusted so as to give maximum radiation whilst maintainning the equipment operative for normal use Internal preset controls not intended to be adjusted during the lifetime of the equipment are not considered to be serivce controls At any point 100mm from the surface of the operator access area the dose rate shall not exceed 1u Sv h 0 1 mR h see Note Account shall be taken of the background level NOTE These values appear in Directive 96 29 Euratom 13 3 1 C Delete note 4 Po 13 3 1 S NO Considered To the second paragraph the following is added In Norway due to the IT power distribution system used the a c MAINS supply voltage is considered to be equal to the line to line voltage and will remain 230V in case of a single earth fault will remain 230V in case of a single earth fault Justification Based on a use in Norway of an IT power distribution ice where the neutral is not provided mo G Delete not 4 and not 5 15 1 1 C Delete note 1 and note 2 15 1 1 To the first paragraph the following is added In Denmark supply cords of single phase appliances having a rated current not exceeding 13A shall be provided with a plug according to the Heavy Current Refulations Section 107 2 D1 Appliances of CLASS provided with socket outlets with earth contact or which are intended to be used in locations where protection against indirect cont
Download Pdf Manuals
Related Search