Installation Manual
Contents
1. 09 13 17 of 22 ENGLISH 7 Portrait Landscape Rotate monitor from Portrait to Landscape through entire range of motion If it does not stay in place or movement in one direction is stiff tension needs adjustment see below Adjust until monitor stays in place and tension portrait to landscape is equal G Adjust Portrait Landscape To Increase Tension Turn screw clockwise To Decrease Tension Turn screw counterclockwise 888 97 335 G 00 rev A 09 13 18 of 22 G Adjustment Step It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation Adjustments should move smoothly and easily through the full range of motion and stay where you set it If adjustments are difficult and do not stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference Lift Up and down Release Brake to move riser CUSTOMER 8 LIFT TENSION AFTER SET UP SEE MANUAL 822 421 00 Q Follow these instructions to tighten or loosen tension 1 2 142. 3 75 35 95 mm Combined LCD and CPU Compartment weight lt 27 Ibs 12 2 kg A CAUTION If the combined LCD and CPU weight is greater than 27 Ibs 12 2 kg then the CPU must be mounted to the rear of the cart using the Universal CPU Holder accessory ordered separately 3 of 22 Tools Needed 14mm 9 16 2x x 14mm 2x o DD M5 x 10mm 4 of 22 888 97 335 G 00 rev A 09 13 1 A Attach the Travel Stop bracket to the lift engine to keep the 1x Iy drawer from hitting the base E Slide the drawer only half way onto the bottom tracks of the existing top drawer m un 888 97 335 G 00 rev 09 13 5 of 22 Remove the top cover on the top drawer and route the cable attached to the bottom drawer up into the control panel on the top drawer Powered Carts 4 Ld 4 Slide the drawer completely onto the bottom tracks of the top drawer 888 97 335 G 00 rev 09 13 6 of 22 5 Replace the top cover on the top drawer Remove the top drawer s D Secure the bottom drawer by attaching the two screws Replace the top drawer s 888 97 335 G 00 rev 09 13 2x M4 x 12mm 7 of 22 On Powered Carts only reset drawer power so
3. 888 97 335 G 00 rev A 09 13 15 of 22 If your monitor uses a screw size other than M4 x 10mm DO NOT use the M4 x 10mm screws or knob provided as they could result in damage to the monitor 75mm 7 10 mm M4 x 10 mm 75mm 75mm 100 mm 200mm 100mm M4 x 10 M4 x 10 mm 888 97 335 G 00 rev A 09 13 16 of 22 Tilt Motion Tilt monitor up and down through entire pivot range of motion If it does not stay in place or move ment in one direction is stiff pivot needs adjustment see below Adjust until monitor stays in place and tilting forces up or down are equal D A 6 Adjust Tilt Increase Friction If this product moves too easily then you ll need to increase friction Decrease Friction A If this product is too difficult to move then you ll need to decrease friction Side to Side Motion Move monitor side to side through entire range of motion If it does not stay in place at any point it will need adjustment see below Adjust so side to side moving forces are equal Increase Friction If this product moves too easily from Adjust Side to Side side to side then you ll need to increase friction A Decrease Friction If this product is too difficult to move from side to side then you ll need to decrease friction 888 97 335 G 00 rev
4. blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement Flevez l cran au plus haut de l ajustement vertical AVANT de le retirer NE retirez PAS la vis d arr t avant que l cran soit fix Dans un tel cas le pivot d cran se rel verait rapidement et cela pourrait engendrer des blessures www ergotron com 826 502 888 97 335 6 00 rev 09 13 20 of 22 Guidance and Manufacturer s Declaration Electromagnetic Emissions Guidance and Manufacturer s Declaration Electromagnetic Immunity Ergotron s Medical Grade Power Strip is intended for use in the Ergotron s Medical Grade Power Strip is intended for use in the electromagnetic environment electromagnetic environment specified below The customer or the user specified below The customer or the user of the Medical Grade Power Strip should assure that it is of the Medical Grade Power Strip should assure that it is used in such an used in such an environment environment Immunity Test IEC 60601 Compliance Electromagnetic environment Emissions Test Compliance Electromagnetic Test Level Level guidance environment guidance Electrostatic 6 kV contact Complies Floors should be wood RF Emissions Ergotron s Medical Grade Discharge ESD 8 kV air concrete or ceramic tile If floors CISPR 11 Power Strip does not use IEC 61000 4 2 are covered with synthetic RF energy for its internal material the relative humidity function The
5. keypad will recognize added drawer NOTE This step is not needed on Non Powered Carts b Disconnect Power System from power source 6 Turn power system off by holding down the AC Outlet Power button for 1 3 seconds Power light will shut off a Turn off all mounted equipment Unplug drawer power cable and then plug it back in to reset E 0 ee INI N lt n eS gt 0 E SN SS 0 E NN E f Replace front base cover 888 97 335 G 00 rev A 09 13 9 of 22 M5 10mm a 2x 2 S SS 888 97 335 G 00 rev 09 13 10 of 22 ENGLISH 11 of 22 12 of 22 My NOTE camera is supplied by customer 1 WY If your monitor has recessed mounting holes you need to add the provided spacer between the monitor and the mounting plate M4 x 14mm d 2x M4 x 14mm 888 97 335 G 00 rev 09 13 13 of 22 ENGLISH 14 of 22 888 97 335 G 00 rev A 09 13 NOTE Make sure scanner holder has been removed from rear of cart as instructed in step 1 on page 10 before attaching pivot M4 x 10mm
6. not use this product without adult supervision Symbol CAUTION Signal Word Color Level of Hazard Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury Used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage INSTRUCTIONS Follow operating instructions INSTRUCTIONS Follow operating instructions ON OFF push push NOTE Each position ON OFF is a stable position Safety A CAUTION Close worksurface before opening drawers Open only one drawer at a time Do Not push cart when drawers or worksurface are open Failure to follow these instructions may cause the cart to be unstable 2 of 22 14mm 9 16 IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Minimize Lift Tension BEFORE Removing Mounted Equipment Shipping Cart Storing Cart To Minimize Lift Tension 1 Lower worksurface to lowest position 2 Turn adjustment nut at top of riser counterclockwise until it stops Adjustment may require 40 60 revolutions Failure to heed this warning may result in serious personal injury or property damage For More information and in
7. warranty visit www ergotron com For local customer care phone numbers visit http contact ergotron com Americas Sales and 2013 Ergotron Inc Corporate Headquarters EMEA Sales ERGOTRON Alright reserved St Paul MN USA Amersfoort The Netherlands While Ergotron Inc makes every effort to provide accurate and complete information on the installation 800 888 8458 31 33 45 45 0 and use of its products it will not be held liable for any editorial errors or omissions including those 1 651 681 7600 WWW ergotron com made in the process of translation from English to another language or for incidental special or www ergotron com info eu ergotron com consequential damages of any nature resulting from furnishing this instruction and performance of sales ergotron com equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its users For the most current product information or to know if this document is available in languages other than those herein APAC Sales Worldwide OEM Sales please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise Tokyo Japan www ergotron com without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA www ergotron com info c
8. Note Ur is the AC mains voltage prior to application of the test level 888 97 335 G 00 rev A 09 13 21 of 22 Safety Alerts Associated with this Product The following Warnings Cautions appear in this reference guide or on the Power Strip NOTE Failure to adhere to these guidelines may result in equipment damage or personal injury A Cleaning and Maintenance The following procedures are not guaranteed to control infection The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes To avoid risk of electric shock do not expose electrical components to water cleaning solutions or other potentially corrosive liquids or substances Do not immerse Power Strip or Power Strip components in liquid or allow liquids to flow into the Power Strip Wipe all cleaners off surface immediately using a damp cloth Thoroughly dry surface after cleaning Do not use flammable cleaners on Power Strip surfaces due to close proximity of electrical power and equipment All paints and plastic Power Strip components will withstand cleaning by most commonly used diluted non abrasive solutions such as quaternary ammonia compounds ammonia enzyme cleaners bleach or alcohol solutions Pen and permanent and dry erase markers can be removed with 91 isopropyl alcohol and a soft cloth lodine stains can be removed with commonly used cleaners and a soft cloth Never use steel wool or other abr
9. User Guide Jensormon StyleView Telepresence Kit with Back to Back LCD 2 Features amp 5 3 Tools Needed amp Components iuascciseerris tbesat estie b tivo rit Per Ek e EH rb ob EVE EE Pv 4 l e 5 9 CPU Holdet m 10 12 CICER 13 14 Rear 15 18 19 AdjUStMENt To Stop Independent LCD 20 Maintenance amp Safety Codi ka ERU EMAILED EINE CLERI 21 22 For the latest User Installation Guide please visit www ergotron com User s Guide English Guia del usuario Espa ol Manuel de l utilisateur Francais Gebruikersgids Deutsch Benutzerhandbuch Nederlands Guida per l utente Italiano Anvandarhandbok svenska www ergotron com USA 1 800 888 8458 OO00 Europe 31 0 33 45 45 600 China 86 769 86018920 888 97 335 G 00 rev 09 13 1 of 22 Hazard Symbols Review These symbols alert users of a safety condi tion that demands attention All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation Children who are not able to recognize and respond appropriately to Safety Alerts should
10. asive materials that will damage the surface finish It is recommended that any cleaning solution be tested on a small inconspicuous area to ensure surface is not harmed A Adjustment Service Replacement DO NOT attempt to adjust service or replace any part of the Power Strip unless directed to do so through Ergotron approved documentation i e installation instructions Only Ergotron Inc or an Ergotron certified entity may adjust service or replace Power Strip components If any component on the Power Strip is missing or damaged the Power Strip must not be used contact Ergotron Customer Care immediately to request a replacement part A Cables Keep cables neatly organized the provided Strain Relief and Hook are designed for this purpose Excess cables should be routed away from moving components with cable clips or ties Review Cable Routing section of this guide or contact Ergotron Customer Care for more information A Customer Equipment Do not connect electrical equipment beyond rated Customer Equipment Only cart mounted electrical equipment should be connected to Power Strip The polarized cord on this Power Strip is Hospital Grade Only Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked Hospital Only or Hospital Grade device is not suitable for use the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide For service and
11. em ergotron com Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc apaccustomerservice ergotron com 888 97 335 G 00 rev 09 13 22 of 22
12. mm 9 16 TE 9 NOTE Adjustment 3 may require 40 60 revolutions SS Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised then you ll need to increase Lift Strength Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered then you ll need to decrease Lift Strength Lift Up and down Q Follow these instructions to tighten or loosen tension aw SS ES 888 97 335 G 00 rev A 09 13 19 of 22 To Stop Independent LCD Lift For heavier Displays or when using a Tablet PC you can keep the LCD Lift from moving out of position by installing this screw into one of the three holes on the back of the riser depending on the desired height ial o kg Y SF With Independent Without Independent LCD Lift Sar LCD Lift 20 Ibs 9 kg 1x o 6 14 Ibs 2 7 6 4 kg M4 x 8mm 3j 21 IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Raise monitor to top of vertical adjustment BEFORE removing DO NOT remove Stop Screw without monitor attached Doing so will cause monitor pivot to shoot up rapidly and may cause personal injury DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de
13. refore its RF should be at least 30 0 low Electrical Fast 2 kV for power supply lines Complies Mains power quality should be and unlikely to cause any Transient Burst 1 kV for input output lines that of a typical commercial or interference in nearby IEC 61000 4 3 hospital environment electronic equipment 5 1 kV differential mod Compli Mai ity should b RF Emissions Class B Ergotron s Medical Grade bil hoo Simples pd dau RE MP IEC 61000 4 5 2 kV common mode that of a typical commercial or CISPR 11 Power Strip is suitable for use hospi ospital environment HarmonicEmissions Class B in all establishments other IEC 61000 3 2 than domestic and those Voltage lt 5 Ur Complies Mains power quality should be directly connected to the Dips short gt 95 dip in Ur for 0 5 cycle that of a typical commercial or Voltage fluctuations Complies public low voltage power interruptions 40 hospital environment flicker emissions supply network that supplies and voltage 60 dip in for 5 cycles IEC 61000 3 3 buildings used for domestic variations on 70 Ur purposes power supply 30 dip in for 25 cycles input lines lt 5 Ur IEC 61000 4 11 gt 95 dip in Ur for 5 seconds Power Complies Power frequency magnetic Frequency fields should be at levels 50 60 Hz characteristic of a typical Magnetic Field location in a typical commercial IEC 61000 4 8 or hospital environment
14. structions refer to product guide at http 4support ergotron com or contact Ergotron Customer Care at 1 800 888 8458 822 052 Important You will need to adjust this product after installation is complete Make sure all your equipment is properly installed on the product before attempting adjustments This product should move smoothly and easily through the full range of motion and stay where you set it If movements are too easy or difficult or if product does not stay in desired positions follow the adjustment instructions to create smooth and easy movements Depending on your product and the adjustment it may take many turns to notice a difference Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation 888 97 335 G 00 rev A 09 13 Features amp Specifications 11 8 300 mm 888 97 335 G 00 rev 09 13 A Weight Capacity With Independent LCD Lift Without Independent LCD Lift 6 14 Ibs 2 7 6 4 kg 20 Ibs 9 See How To Eliminate Independent LCD Lift section 2 lbs 0 9 kg 0 Ibs 0 kg Open Worksurface lt 5 Ibs 2 3 kg Closed Worksurface 13 Ibs 5 9 kg CPU Compartment gt lbs 10 5 kgs A B lt 25 5 lt 2 Ibs 0 9 kg 11 3 kg 2 lbs 0 9 kg SA lt 2 lbs 1 kg 1 38
Download Pdf Manuals
Related Search