Home

User`s Manual

1. Off Yellow On Yellow Off Red On Red Off G Pi_Link PO Lirik PWR Piet FAULT NSM 206FT 4 Port 10 100 Base TX With 2 Port 100 Base FX Switch Color Description Core Power is OK Core Power is Off Link Act Not Networking Link Act Not Networking Link Act Not Networking Link to 100 Mbps Link to 10 Mbps Power is being supplied to power input PWR2 Power is not being supplied to power input PWR2 Power is being supplied to power input PWR1 Power is not being supplied to power input PWR1 Power is not being supplied to power input PWR1 and PWR2 Power is being supplied to power input PWR1 and PWR2 Redundant Power Inputs Both power inputs can be connected simultaneously to live DC power sources lf one power source fails the other live source acts as a backup and automatically supplies all of NSM 206Fx s power needs Soft start Power Inputs Integrated soft start function that limits the in rush current to the device being powered Delay time Rise time 2 second Pin Function For Terminal Block External power supply is connected using the removable terminal block PWR1 Power input 1 10 to 30Vdc PWR2 Power input 2 10 to 30V and should be connected to the power supply GND Ground and should be connected to the power supply R COM Common Form A Relay for Alarm contact R NO F G Normal Open Form A Relay for Alarm contact F G stand
2. EDs LED1 or LED2 will be ON solid when you made the Full duplex mode Full duplex Default Transmission Distance 2Km JP1 for Fiber Port P1 JP2 for Fiber Port PO Half duplex Transmission Distance 412m JP1 for Fiber Port P1 JP2 for Fiber Port PO Dimensions 110 02mm z3
3. NSM 206F T NSM 206FC NSM 206FCS Industrial 4 Port 10 100 Base T X with Dual 100 Base FX Switch Introduction The NSM 206Fx is an unmanaged 4 Port Industrial Ethernet 10 100Base TX witch dual Fiber 100Base FX Switch that secures data transmission by using fiber optic transmission to provide immunity from EMI RFI interference The Ethernet supports 10 100M auto negotiation feature and auto MDI MDIX function s NSM 206FT r Fm NSM 206Fx provides two power inputs that can be connected simultaneously to live DC power sources If one of the power inputs fails the other live source acts as a backup to automatically support the NSM 206Fx s power needs NSM 206Fx contains soft start function with overload protection high low voltage protection Features Automatic MDI MDI X crossover for plug and play Each port supports both 10 100 Mbps speed auto negotiation Full duplex IEEE 802 3x and half duplex backpressure flow control 1 6 Gbps high performance memory bandwidth Frame buffer memory 256 Kbit Integrated look up engine with dedicated 1 K unicast MAC addresses Redundant Power Inputs 10 30V DC Power failure alarm by relay output e DIN rail mount for industrial usage Specifications e Compatibility IEEE 802 3 IEEE802 3u IEEE802 3x e Interface NSM 206FT 10 100 Base T X and 100 Base FX ST Connector Multi mode NSM 206FC 10 100 Base T X and 100 Base FX SC Connector Multi mode NSM 206FCS 10 100 Ba
4. s for Frame Ground protective ground It is optional If you use this pin it can reduce EMI radiation improve EMI performance and ESD protection NSM 206Fx User s Manual Version 1 0 Oct 2006 2 Application Note 1 Redundant Power Inputs amp Relay Output Alarm NSM 206Fx provides two power inputs that can be connected simultaneously to live DC power sources If one of the power inputs fails the other live source acts as a backup to automatically support the NSM 206Fx s power needs The NSM 206Fx provides relay contact outputs to warn technicians on the shop floor when the power fails 24VDC Power supply PWR2 Relay Output 2 Fiber Daisy Chain The NSM 206Fx can extend your LAN in a daisy chain configuration Fiber cable 2Km Fiber cable Km NS 200Fx NSM 206Fx NS 205Fx Full Half Duplex Selection There are two modes of data transmissions full duplex and half duplex transmission The data can be transmitted in both directions on a single carrier at the same time when you select Full duplex mode But the data can only be transmitted in one direction on a single carrier at the same time when you select Half duplex mode You may select Full or half duplex mode according to your equipment requirement You can configure full or half duplex NSM 206Fx via Jumper Default full duplex Note Note You must cycle power to the switch after changing the jumper position The L
5. se T X and 100 Base FX SC Connector Single mode e Ethernet Port 10 100 Mbps x 4 e Fiber Optic Port 100 Mbps x 2 e Fiber Optic Transmission distance Multi mode fiber cables 50 125 62 5 125 or 100 140 um Distance 2 km 1300 1310nm 62 5 125 um Min TX Output 20 dBm Max TX Output 14 dBm Sensitivity 34 to 31 dBm Single mode fiber cables 8 3 125 8 7 125 9 125 or 10 125 um Distance 15 km 1300 1310 nm 9 125 um Min TX Output 15 dBm Max TX Output 8 dBm Sensitivity 36 to 31 dBm e Ethernet Cables 10 Base T Cat 3 4 5 UTP cable 100m Max 100 Base TX Cat 5 UTP cable 100m Max e Environment Operating Temperature 0 C 70 C Storage Temperature 20 85 C Relative Humidity 10 to 90 non condensing e Dimensions 72 5 x 110 x 104 mm W x H x D e Power requirements 10 to 30V DC Removable Terminal Block Alarm Contact One relay output with current carrying capacity of 2A 30 VDC e Power consumption 0 24A 24Vdc 5 arrowed NSM 206Fx User s Manual Version 1 0 Oct 2006 1 LED functions Standard RJ45 female connectors are provided A standard RJ45 plug cable is necessary to connect your device to the unit since switch that supports auto crossover LED PWR_OK Link for PO Link for P1 Ethernet Port P2 P5 PWR2 PWR1 FAULT Red On Red Off Green On Green Off Yellow On Yellow Off Green On Green Off Yellow On Yellow Off Green On Green

User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents