PLRB™ Manual - poplocks.com
Contents
1. GUIDE COPY TO REMAIN IN VEHICLE Complete PLRB In Enclosure 1 pjm m e Ri e e o o e e e o e es o os Component I D F BHRHRHRHRHRHRHRHEHEEEEE i uT LO 3 7 CHASIS DAL ERA I RHN POW aapt mlar il 7 Ja mole a t a t 1 I I EM sd Part List 1 6 pin timed relay 2 5 pin 30 40 relays 3 30 amp fuses 4 Eight 1 4 stab connectors 5 Power amp Ground lugs 6 2 red 2 green LEDs 7 RC unit location and mounting hole J 1 Module Keyless Entry Control Module Input J 3 Toggle Dip Switch 3rd Channel Flip Flop Option External Output 3rd Channel Or Additional Piggy Back Relay Option Use Provided Jumper And Close Pins Indicated To Activate 3rd Channel Slave Piggy Pack On Close Pins 3C As Indicated pam 4 tA HDClne POP ETA Troubleshooting Keyless Entry amp PLRB RC3 TROUBLE SHOOTING PLRB RC3 amp POWER LOCK SYSTEM 1 Both transmitters fail and vehicle rocker switch continues to work correctly 2 One transmitter works correctly the other does not 3 One compartment fails to lock or unlock 4 a One entire side of the vehicle will not lock or unlock 5 a The vehicles compartments lock and un2. a test light Connect it to power With probe touch positive input trigger lock unlock 7 a Replace battery 8 a There is a short after the main control module Examine the wire harness for damage rA WwWWwWw poplocks com Code Learning PLRB RC3 Transmitter Programming Instructions oO Code Learning Transmitter Programing Instructions Section 1 Programming RC 3CH to learn additional transmitter codes The RC 3C will learn up to three 3 different transmitter codes To add a new transmitter code complete the following procedure 1 Unplug the RC Keyless Brain from the Control Module Disconnect the battery of the vehicle and use a test light to discharge any remaining static current 2 Re plug the Control Module brain of the RC into the wiring harness or reconnect the battery of the vehicle Sa Immediately press Button 1 of each transmitter to be used with the RC one after the other Please note that when adding a new code you must press button 1 on the transmitter of each code to be used with the unit even if it already knows the transmitter code previously Section 2 Transmitter Battery Replacement Instructions ile Remove the screw from the back of the transmitter 2 Remove the front cover Remove the old battery carefully 3 Replace with new battery and close front cover We recommend the use of 12V GP23A or similar 4 Press any button Check for light flash from LED If no LED flash change pol
3. arity of battery Note Normal battery life is approximately two years but varies depending on usage For optimum performance and RF range replace the battery at least once a year 3 Channel Transmitter Keyfob Channel One Button One Unlocks Outboard Relay Channel Two Button One When Pressed Immediately After Unlocks The PLRB RC3 Control Board Channel Three Button Two Locks Outboard And M ain Control M odule E c www poplocks com
4. lock but the switch in the cab will not work 6 a The vehicles power locks fail to work from the rocker switch but the remotes work correctly 7 a Remote key fob must be close to the vehicle before working correctly 8 a Fuses on the control board repeatedly open blow when locking system is cycled Solution l a First check the transmitters battery 1 b Find the wire harness to the receiver 4 wires blue green red black and unplug the harness to disconnect power to the receiver Wait approximately 3 minutes and plug it back in With in 2 5 seconds press button 1 of transmitter 1 then button 2 of transmitter two This process is call re coding 2 a Check the battery of the transmitter not working 3 a Make sure all connecting contact are complete and fully 4 plugged 3 b Test the wiring by removing the non working actuator from the wire harness at the actuator Using a test light probe connect to both contacts from the wiring harness The test light should only momentarily light when the locking system is cycled 4 a Check the main control module fuses and replace if necessary 4 b Confirm that the LED lights light during lock unlock cycle s 4 c Verify that the wire harness in the vehicle is not cut or damaged 5 a Please refer to solutions 4 a 4 b and 4 c 6 a Look for loose or damaged wires at the rocker switch or control module 6 b Test simulate trigger at the control module using
Download Pdf Manuals
Related Search