Datexel Datasoft User Manual and Guide
Contents
1. eo oe hele are ee Picture 13 SWITCH MODE DAT4532 Series Screenshot e To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on the device connected the sections of the window will be automatically updated in function of the programming set To visualize how to configure the device Section Input 67 allow to select the type of sensor to apply on input the sections SW1 amp SW2 70 and Zero amp Span 69 will be automatically updated in function of input selected Section Zero amp Span 69 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 70 will be automatically updated in function of the values selected Note for each type of input it is possible to insert Default values for zero and Span and to save them in Eeprom To perform such operation click on the position Def of the columns Zero and Span make a double click by the left button of the mouse write the value and confirm clicking on the button OK The device will follow the values of Default set only when the DIP switches dedicated to the setting of input scale are in OFF position Section Output 68 allow to select the output type for each output channel the sections2. 40 A allows to set the options for the input and output signals per channel Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C per step of 0 1 C or 22 5 F per step of 0 2 F RTD or resistance setting of the cable compensation as 2 3 or 4 wires 40 A Output options Setting of the break condition out of scale value as Up output signal higher than the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range Pag 8 of 20 Picture 8 PROGRAM MODE DAT 4540 Program Input A Output Analog Type Freq fa Type 4 20 m Max 20000 Hz Max 20 m i Min A m Min 0 Hz 0 1 20000 Hz 41 4 20 m 50 Hz Filter Smooth 43 Span min 1 Hz Span min 4 m 42 Hi 21000 Hz Hi 21000 Hz Lo 20900 Hz Lo 20900 Hz Was Max NO Min Min C NC 45 DAT 4540 Picture 8 Screenshot Section Input A 41 shown the input sensor type Frequency the minimum and the full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section Section Output A 42 allows to select the output type and set the minimum and maximum values of the output range The specification limits
3. 34 A 34 B allows to set the options for the input and output signals per channel Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C variable per step of 0 1 C or 22 5 F per step of 0 2 F RTD PTC or resistance setting of the cable compensation as 2 or 3 wires 34 A The options selected in this section work on both the output channels Output options Setting of the break condition out of scale value as Up output signal higher than the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range The options selected in this section work separately per output channel Option Functions 34 B For the devices with current or voltage input are available the following type of output linearisation e Linear output signal proportional with the input e Tank special linearisation to measure the variation of the level of a liquid in an horizontal cylindrical tank e SQRT special linearisation to measure sensors that require a square root extraction The options selected in this section work separately per output channel Pag 6 of 20 Picture 6 PROGRAM MODE DAT 4531 Series m Program E l ars Input A Output A Type Te E Type 4 20 m w C r F blar 20 m blax 400 E Min OT Min
4. perform such operation click on the position Def of the columns Zero and Span make a double click by the left button of the mouse write the value and confirm clicking on the button OK The device will follow the values of Default set only when the DIP switches dedicated to the setting of input scale are in OFF position Sections Output 76 shown the output type of the device 4 20 mA the sections SW1 amp SW2 78 will be automatically updated in function of the values selected Sections SW1 amp SW2 78 in this section is shown the position of the dip switches Every programming set or visualized is checked to verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 61 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 16 of 20 Picture 16 SWITCH MODE DAT4540 w Switch Wizard 5 x oT AARRAAHA BARH eo eine eos 234 4 ee Check Picture 16 SWITCH MODE DAT4540 Screenshot To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on th
5. Down output signal lower than the minimum output value setting of the break level as percentage of the output range Option Functions 37 B For the device with current or voltage input are available the following type of output linearisation e Linear output signal proportional with the input e Tank special linearisation to measure the variation of the level of a liquid in an horizontal cylindrical tank e SQRT special linearisation to measure sensors that require a square root extraction Pag 7of 20 Picture 7 PROGRAM MODE DAT 4535 i Prooram Input A Option o Tee Type 4 20 m fC tf F High Speed 20 Max 400 C Max i 4 Delay sec Min 0 c Min m 200 1200 C 4 20 m span min 4 m DAT 4535 Picture 7 Screenshot Section Input A 38 allows to select the input type and set the zero and full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Section Output A 39 allows to select the output type and set the minimum and maximum values of the output range The specification limits admitted for the output type selected are shown on the bottom side of the section Section Options 40
6. been made a a wrong configuration of the dip switches Solution control the dip switches settings Error messages Communication error shows that the data communication between DATESOFT and the device doesn t end correctly Solutions Control that all the cables of the PRODAT interface have been correctly connected Control that the device has been correctly supplied referring to the technical data sheet No COM port available shows that at the moment of click the button Open Com Datesoft does not find any communication port available Solutions Verify the connections of the USB cable of the interface PRODAT Verify the correct installation status of the communication interface PRODAT in the section Control Panel System and Maintenance Device Manager of the operative system in use COM Port already in use shows that the Com port selected is already in use from another application Solutions Close the external application Change the Com port Verify and eventually change the correct Com Port number set in the section Control Panel System and Maintenance Device Manager of the operative system in use Error check configuration data shows that one or more parameters are not correct programming via PC Solution Verify that all parameters are included within the specification limits Device Changed shows that the user tries to program a device of type and or version d
7. function of input selected For the temperature sensors there is the field Options that allows to set the CJC type as Internal or External thermocouples except the type B and the cable compensation as 3w or 2w 4w RTD and Resistance For the temperature sensors before to set the sections Zero and Span select the option C F Section Zero amp Span 90 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 91 will be automatically updated in function of the values selected Section Output 89 allow to select the output type for each output channel the sections SW1 amp SW2 91 will be automatically updated in function of the values selected Section Switch 91 in this section is shown the position of the dip switches Section Limits 92 shown the limits of programming in function of the type of input selected Pag 19 of 20 SSS ERROR MESSAGES AND CONDITIONS OF ERROR Error conditions Blinking condition of the device s LED PWR shows that has been made a wrong configuration of the dip switches Solution control the dip switches settings No DATESOFT activity Solution control that the communication has been enabled by the button Open Com 2 Picture 1 Configuration Check s LED red 39 Pictures 7 and 8 shows that has
8. proportional with the input e Tank special linearisation to measure the variation of the level of a liquid in an horizontal cylindrical tank e SQRT special linearisation to measure sensors that require a square root extraction Pag 5 of 20 Picture 5 PROGRAM MODE DAT 4631 Series Program O T 5 x Input A TeK oO 6m Type Type 0 10 External AF IES i Internal Mas 200 C Max 10 ro i F of fe 3 Min TO n Min Vv Offset C 200 1300 C o 10 Span min 100 C 31 span min TM R Function f Linear C Tank C SORT 34 B Type Mas e0 mA Min 4 m O 20 m Span min m 33 DAT 4631 SERIES Picture 5 Screenshot Section Input A 31 allows to select the input type and set the zero and full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section sections The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Sections Output A 32 and Output B 33 allow to select the output type for each channel and set the minimum and maximum values of the output range The specification limits admitted for the output type selected are shown on the bottom side of the section Section Options 34
9. the break condition out of scale value as Up output signal higher than the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range It is possible to select different break points per each output channel Section Options 23 allows to set the function of doubler and to set a delay time with step of tenth of seconds up to 30 seconds on output signal Section Trip 25 allows to e set the trip and the hysteresis levels in the same engineering units of the input range Hi and Lo e set the type of trip as high or low alarm Max and Min e set the delay time of energizing and de energizing of the threshold expressed in seconds Delay Pag 4of 20 Picture 4 PROGRAM MODE DAT 4532 Series Ar aul Input A Type Te K Fre ns ar eo Re UV 7 Output A T 0 20 rut ane C External hd aw 20 rh f Internal Min D m Offset 0 3 C annann 200 1300 C Span mim 100 C 26 e H if ee Max a00 AE Mn 099 200 1200 C Span min 100 C 0 20 m Spanmin 4m 27 Function i Linear C Tank T 0 20 ma do External SORT blas 40 m 0 intemal Min D m 0 5 H 0 20 m4 Span min 4 m 29 OE DAT 4532 SERIES Picture 4 Screenshot Sections Input A 26 and Input B 28 allow to select the input type for each channel
10. the same for both the channels excepted the version D where the configuration via dip switches is dedicated per channel Note it is possible to visualize and change the data in this window only if the communication has been enabled by the button Open Com 2 Picture 1 Picture 12 SWITCH MODE DAT4530 w Switch_Wizard x Wizard gt 161 af a e A a p a Se Ee ae Chec SEREARBE of a 5 oe Gf A Picture 12 SWITCH MODE DAT4530 Screenshot e To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on the device connected the sections of the window will be automatically updated in function of the programming set e To visualize how to configure the device Section Input 62 allow to select the type of sensor to apply on input the sections SW1 amp SW2 66 and Zero amp Span 65 will be automatically updated in function of input selected For the temperature sensors there is the field Options that allows to set the CJC type as Internal or External thermocouples except the type B and the cable compensation as 3w or 2w 4w RTD and Resistance Section Zero amp Span 65 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 66 will be au
11. vDAtEXEL O OMATESOFT Datasoft User Manual r Tel 1 561 779 5660 e mail datexel datexe com www datexel com User Guide GENERAL DESCRIPTION DATESOFT is a software developed by Datexel srl running under the operative system Windows designed to program and visualize the measure of the converters programmable by PC listed in the table below To operate with DATESOFT it is necessary to use the programming interface PRODAT between the P C and the device on programming To connect devices and interface refer to the relative technical Data sheets SYSTEM REQUIREMENTS v usable interface Operative System Windows XP Vista 7 8 Available Hard Disk space 2 MB PROCEDURE OF INSTALLATION e Close eventual active or background applications e Insert the installation CD ROM into the driver e Wait for the Autorun s window opening open the CD ROM and execute the installation file using the path lt CD Driver gt file lt CD Driver gt file D eng tools software html Click on the button download e Follow the Installation Wizard OPEN DATESOFT Connect the programming interface PRODAT to the Com port of the PC If the programming interface is the PRODAT USB verify the Com port number assigned to it by Windows during its installation go to Control Panel System and Maintenance Device Manager Connect the PRODAT to the device by the proper cable as shown in the device s data sheet P
12. 1 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 15 of 20 Picture 15 SWITCH MODE DAT4535 Switch_Wizard ll 5 x On Off Controllo Config T Off OK eo Gf a Picture 15 SWITCH MODE DAT4535 Screenshot e To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on the device connected the sections of the window will be automatically updated in function of the programming set To visualize how to configure the device Section Input 75 allow to select the type of sensor to apply on input the sections SW1 amp SW2 78 and Zero amp Span 73 will be automatically updated in function of input selected For the temperature sensors there is the field Options that allows to set the CJC type as Internal or External thermocouples except the type B and the cable compensation as 3w or 2w 4w RTD and Resistance Section Zero amp Span 73 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 78 will be automatically updated in function of the values selected Note for each type of input it is possible to insert Default values for zero and Span and to save them in Eeprom To
13. SW1 amp SW2 70 will be automatically updated in function of the values selected Sections SW1 amp SW2 70 in this section is shown the position of the dip switches Every programming set or visualized is checked to verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 61 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 14 of 20 Picture 14 SWITCH MODE DAT4531 series and DAT4631 Series im Switch_Wizard ill 5 x AHAAA pe eee a ea SW a fe 2 fi ee ee sees eae Configuration Check Picture 14 SWITCH MODE DAT4531 and DAT4631 Series Screenshot To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on the device connected the sections of the window will be automatically updated in function of the programming set To visualize how to configure the device Section Input 71 allow to select the type of sensor to apply on input the sections SW1 amp SW2 74 and Zero amp Span 73 will be automatically updated in
14. W2 85 in this section is shown the position of the dip switches Every programming set or visualized is checked to verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 61 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 18 of 20 MODE WIZARD By this window it is possible to visualize even with device not connected how to set the dip switches of the devices of the SLIM series in function of the input and output selected The parameters shown in function of the device selected This option ts not available for the device DAT1135 Picture 18 Mode Wizard m Switch SSE 92 SMS BERRREWE BE Po te es Gees et 2 3 4 HWhAAHBH Bo S pba oe he Picture 18 MODE WIZARD Screenshot Button Back 86 allow to return back to the Switch Mode window Button of selecting Model 87 allows to select the device of which the user wants to visualize the configuration Section Input 88 allow to select the type of sensor to apply on input the sections SW1 amp SW2 91 and Zero amp Span 90 will be automatically updated in
15. a 4A 20 m 200 1200 C Span min 4 m 36 Ne Span min 100 C 39 Wi res External i nterral Offset o o E Function 0 Linear C Tank DAT 4531 SERIES Picture 6 Screenshot Section Input A 35 allows to select the input type and set the zero and full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Section Output A 36 allows to select the output type and set the minimum and maximum values of the output range The specification limits admitted for the output type selected are shown on the bottom side of the section Section Options 37 37 A 37 B allows to set the options for the input and output signals per channel Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C per step of 0 1 C or 22 5 F per step of 0 2 F RTD PTC or resistance setting of the cable compensation as 2 or 3 wires 37 A Output options Setting of the break condition out of scale value as Up output signal higher than the maximum output value or
16. admitted for the output type selected are shown on the bottom side of the section Section Options 43 allows to set the type of signal of which measure the frequency and the relative options Option 50 Hz Filter block the signals with frequency higher than 50 Hz Smooth set the delay on output Sections Trips A 44 and Trips B 45 allow to set the threshold values the type of the threshold and the relative delay time for each threshold of the device Pag 9 of 20 Picture 9 PROGRAM MODE DAT 4632 D w Program Function Linear t SORT Min 0 Vf 0 10 O0 10 Span min 1 46 Span min 7 W S f Linear C SORT Tank DAT 4632 D Picture 9 Screenshot Sections Input A 46 and Input B 48 allows to select the input type and set the zero and full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section Sections Output A 47 and Output B 49 allows to select the output type and set the minimum and maximum values of the output range The specification limits admitted for the output type selected are shown on the bottom side of the section Sections Options A 50 and Options B 51 allow to set the options for the output signal per each channel Output Option Setting of the break condition out of scale value as Up output signal higher than
17. and the zero and full scale values of the input ranges The specification limits admitted for the input type selected are shown on the bottom side of the sections The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Sections Output A 27 and Output B 29 allow to select the output type for each channel and the minimum and maximum values of the output ranges The specification limits admitted for the output selected are shown on the bottom side of the sections Section Options 30 30 A 30 B allows to set the options for the input and output signals per channel Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C variable per step of 0 1 C or 22 5 F per step of 0 2 F RTD PTC or resistance setting of the cable compensation as 2 or 3 wires 30 A Output options Setting of the break condition out of scale value as Up output signal higher than the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range Option Functions 30 B For the devices with voltage or current input are available the following type of output linearisation e Linear output signal
18. ata from the device Button Write 9 when the Program mode window is active allows to send the new programming data to the device Button Start Stop 10 starts or stops the reading of the data measured from the device in the Measure mode Button Language 11 allows to set the language English or Italian of DATESOFT Pag 2of 20 gt eee eer MEASURE MODE Picture 2 Picture 2 Measure Mode active iix Ted 0 800 C The Measure mode window allows to visualize in real time the input and output measures This window appears clicking on the button View measure 5 Picture 1 on the Toolbar and works only if the communication with the device has been enabled button Open Com 2 Picture 1 To start the measure click on the button Start Stop 10 Picture 1 on the Toolbar to stop the measure click on the same button It is possible to visualize the measures either if the device has been programmed by PC or by dip switches Screenshot Button I gt 10 Picture 1 Start the measure process The device will send the measured data to the software Do not disconnect the serial cable during this operation Button I 10 Picture 1 Stop the measure process Sections Input A 12 and Input B 14 visualize the input measures of each channel expressed in the engineering unit programmed the input type and range programmed are shown on the b
19. d Section Trip B Picture 2B 17 the parameters H and L shown the two threshold values high H and low L set in the Program mode the parameter MAX or MIN shows the type set for the threshold the parameter Delay shows the delay time set for the threshold For the sections 16 and 17 the LED changes colour as following in function of the state of the thresholds Green threshold not active Red threshold active Yellow threshold in condition of transition from active to not active and vice versa the colour yellow is present for the time set in the parameter Delay Section Alarm Picture 2A and 2B 18 this parameter shows the type of Fault alarm sensor It is not active for DAT4530 Pag 3 of 20 SSS PROGRAM MODE By this window it is possible to set the parameters of configuration and to save them in Eeprom The input and output parameters programmed by this window will be active only if all of the dip switches relative to the input types are in OFF position vice versa the options parameters will be active either in case of programming by PC or dip switches The visualization of the programmable parameters depends on the type of device connected Notes 1 it is possible to change the data in this window only if the communication has been enabled Open Com 2 Picture 1 2 the parameters programmed are saved in Eeprom also if the device has been configured by dip switches P
20. e Program mode Measure start starts the reading of the data measured from the device in the Measure mode Measure stop stops the reading of the data measured from the device in the Measure mode Menu contains the information about DATESOFT and a direct link to the DATEXEL website Command Exit allows to exit DATESOFT TOOLBAR Picture 1 Button Com 1 allows to set the number of the Com port port numbers available from 1 to 16 Button Open Close Com 2 enables Open Com or stops Close Com the communication with the device Filling bar and led of communication 3 the filling bar shows the progress of the data transmission from DATESOFT to the device The red led shows the data transmission in progress the green led the end of it In the Measure mode when the data transmission is continuous the led blinks from red to green Label Version 4 snows the type and version of the device connected Button View measure 5 allows to move to the Measure mode window if it is still open or to open it Button View program 6 allows to move to the Program mode window if it is still open or to open it Button View switch 7 allows to move to the Switch mode window if it is still open or to open it Button Read 8 when the Program and or the Switch mode windows are active allows to read the programming d
21. e device connected the sections of the window will be automatically updated in function of the programming set To visualize how to configure the device Section Input 79 allow to select the type of sensor to apply on input the sections SW1 amp SW2 82 and Zero amp Span 80 will be automatically updated in function of input selected Section Zero amp Span 80 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 82 will be automatically updated in function of the values selected Note for each type of input it is possible to insert Default values for zero and Span and to save them in Eeprom To perform such operation click on the position Def of the columns Zero and Span make a double click by the left button of the mouse write the value and confirm clicking on the button OK The device will follow the values of Default set only when the DIP switches dedicated to the setting of input scale are in OFF position Section Output 81 allow to select the output type for each output channel the sections SW1 amp SW2 82 will be automatically updated in function of the values selected Sections SW1 amp SW2 82 in this section is shown the position of the dip switches Every programming set or visualized is checked to
22. function of input selected Section Zero amp Span 73 shown the minimum value Zero and the full scale value Span of input when it is necessary to program the device click on the two columns the selected values the sections SW1 amp SW2 74 will be automatically updated in function of the values selected Note for each type of input it is possible to insert Default values for zero and Span and to save them in Eeprom To perform such operation click on the position Def of the columns Zero and Span make a double click by the left button of the mouse write the value and confirm clicking on the button OK The device will follow the values of Default set only when the DIP switches dedicated to the setting of input scale are in OFF position Section Output 72 allow to select the output type for each output channel the sections SW1 amp SW2 74 will be automatically updated in function of the values selected Sections SW1 amp SW2 74 in this section is shown the position of the dip switches Every programming set or visualized is checked to verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 6
23. icture 3 Program Mode DAT 4530 Input Output A Type Jo 20 m oO me 5 x Option External High Speed nterral W Doubler Delay sec Dz Wires fe 2 Od Max 20 m Min m Max 300 C Mir 0 Offset U3 C O 20 m Span min 4 m 1 Options B 24 DAT 4530 Picture 3 Screenshot Section Input 19 allows to select the input type and the zero and full scale values of the input range The specification limits admitted for each input type selected are shown on the bottom side of the section The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Sections Output 20 allows to select the output type and the minimum and maximum values of the output range for each output The specification limits admitted for each output selected are shown on the bottom side of the section Section Input options 19 19 A allows to set the options for the input signal Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C variable per step of 0 1 C or 22 5 F per step of 0 2 F RTD or resistance setting of the cable compensation as 2 3 or 4 wires 24 Output options Setting of
24. ifferent from that one which DATESOFT has been opened Ex from DAT4532 A to DAT4532 D Solution Click on the button Close Com then Open Com 2 Picture 1 to start a new communication Device not compatible with this software version shows that has been connected a DATEXEL device different from those listed on the page 1 of this document Solution Connect a device of right type and version Wrong configuration Channel A input must be a Thermocouple with Internal CJC shows with a device of the version A connected that the user is programming the channel B as a Thermocouple with internal CJC but the channel A has been programmed as mV or Thermocouple with external CJC or B type Solutions Set the channel A as a Thermocouple with internal CJC Set channel A like channel B or vice versa MAX MIN Span input value exceeds limits shows that one or more of the input parameters are not included between the specification limits Solution control the parameters see section Program mode MAX MIN output value exceeds limits shows that one or more of the output parameters are not included between the specification limits Solution control the parameters see section Program mode ED 01 14 REV 00 Datexel s r l reserves its right to modify its products totally or in part without notice at any time Paa 20 of 20 _ E E eee
25. imits admitted for the output type selected are shown on the bottom side of the section Section Options 95 95 A allows to set the options for the input and output signals per channel Input options Thermocouple setting of the CJC as internal or external not required for the B type setting of the CJC offset value with a maximum variation of 12 5 C per step of 0 1 C or 22 5 F per step of 0 2 F RTD or resistance setting of the cable compensation as 2 3 or 4 wires 95 A Output options Setting of the break condition out of scale value as Up output signal higher than the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range It is possible to set a Delay on output expressed as seconds Delay up to the limit of 30 seconds to eliminate eventual sudden variation of the same signal Pag 12 of 20 SWITCH MODE By this window it is possible to control and set the dip switches The visualization of the programmable parameters depend on the type of device connected To execute these operation it is necessary to keep the device connected This option is not available for the device DAT1135 The setting of the dip switches will force the device working the options setting saved in Eeprom work only if they are not selectable by dip switch For the devices with double channel the configuration via dip switches is
26. ottom left side of the each section Sections Output A 13 and Output B 15 visualize the output measures of each channel expressed in the engineering unit programmed the output type range programmed are shown on the bottom left side of the each section The sections 12 13 14 and 15 will be visualized in function of the type of device connected DAT 4535 and series DAT 4531 visualization of the sections 12 and 13 Series DAT 4532 visualization of the sections 12 13 14 and 15 Series DAT 4631 visualization of the sections 12 13 and 15 DAT4530 visualization of the sections 12 13 and 15 The section 14 is updated as section Trips Picture 2A DAT4540 visualization of the sections 12 and 13 The section 14 is updated as section Trips Picture 2B MEASURE MODE SECTION TRIPS Pictures 2A and 2B Pictures 2A 2B Section Trips active for DAT4530 Picture 2A and DAT4540 Picture 2B Picture 2A Picture 2B Trips oA H 210 C MAX B tina rise Delay 1 se 16 17 4 H 21000H2 MAX Tipa L 20900H2 Delay 10s 2 OM AS De ety 10a Sem A L Ss a Section Trips Screen shot Section Trip A Pictures 2A and 2B 16 the parameters H and L shown the two threshold values high H and low L set in the Program mode the parameter MAX or MIN shows the type set for the threshold the parameter Delay shows the delay time set for the threshol
27. ower on the device Be sure that the Com port selected is not used by other applications or programs Execute the program at the path Start Programs DATESOFT DATESOFT When the software is running the default window appears Picture 1 Set the number of the Com port 1 Picture 1 Click on the button Open Com 2 Picture 1 the program tries to communicate with the device If the communication ends correctly the led of communication becomes green 3 Picture 1 When active DATESOFT allows the user to e program the device by PC Program mode e visualize the measure Measure mode e control the dip switches settings and configure them with device connected Switch mode e view how to set the dip switches with device not connected Switch Wizard Fag 1 of 20 Picture 1 Toolbar communication active DATESOFT v 2 7 File View Action Exit MENU BAR Picture 1 Menu File not active Menu View contains the commands to recall the mode windows of the software Measure allows to recall the Measure mode window Program allows to recall the Program mode window Switch allows to recall the Switch mode window Menu Action contains the following action commands Program read allows the user to read the configuration data from the device in the Program mode Program write allows the user to send the configuration data to the device in th
28. the maximum output value or Down output signal lower than the minimum output value setting of the break level as percentage of the output range The following type of output linearisation are available Linear output signal proportional with the input Tank special linearisation to measure the variation of the level of a liquid in an horizontal cylindrical tank SQRT special linearisation to measure sensors that require a square root extraction Button Algebraic function 52 allows to recall the menu wherein define the Algebraic function Picture 10 Picture 10 PROGRAM MODE Algebraic function DAT 4632 D i 5 x i Program Algebraic Functor Input A Physical Pag 10 of 20 Picture 10 PROGRAM MODE Algebraic function DAT 4632 D Screenshot Sections Input A and Input B 53 shown the input type applied to the input the minimum and the full scale value of the input set in the main window of the Program mode Picture 9 Sections Physical 54 allow to set the physical value to associate to the input parameters to execute the mathematical calculation Sections Math operator 55 allows to set the mathematical operator to execute the calculation Picture 11 Sections Physical 56 allow to set the physical value to associate to the output parameters to execute the mathematical calculation Sections Output A and Output B 57 shown
29. the type of signal the minimum the maximum value of the output range set in the main window of the Program mode Picture 9 Button Back 58 allows to return back to the main window of the Program mode Picture 9 Picture 11 Mathematical operator DAT 4632 D w Functions Picture 11 Mathematical operator DAT 4632 D Screenshot Button Back 59 allows to set the mathematical operator for the calculation Button OK 60 allows to return back to the window of the Algebraic function Picture 10 Pag 11 of 20 Picture 19 PROGRAM MODE DAT 1135 w Prooram c aD x Input A Option Type Tes a pov Ti C External Up f C f F E 10 Internal D owr hla w n Max Y Delay sec Miri 0 eae 200 1200 C O 10 N pan min 100 C 93 Span min 1 94 N Dz DAT 1135 Picture 19 Screenshot Section Input A 93 allows to select the input type and set the zero and full scale values of the input range The specification limits admitted for the input type selected are shown on the bottom side of the section The parameter C F allows the user to set the Program window also in F for the temperature sensors Note at the first connection the measures are always shown as C Section Output A 94 allows to select the output type and set the minimum and maximum values of the output range The specification l
30. tomatically updated in function of the values selected Note for each type of input it is possible to insert Default values for zero and Span and to save them in Eeprom To perform such operation click on the position Def of the columns Zero and Span make a double click by the left button of the mouse write the value and confirm clicking on the button OK The device will follow the values of Default set only when the DIP switches dedicated to the setting of input scale are in OFF position Sections Output 64 allow to select the output type for each output channel the sections SW1 amp SW2 66 will be automatically updated in function of the values selected Sections SW1 amp SW2 66 in this section is shown the position of the dip switches Every programming set or visualized is checked to verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 61 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 13 of 20 Picture 13 SWITCH MODE DAT4532 series ee 5 x Wizard gt 61 SWITCH ASAGAGAL A Gees Se Configuration Check OWT SEBO
31. verify that the data inserted are included into the specification limits of the device The field Configuration check will be green with the indication OK if the data inserted are included into the specification limits of the device will be green with the indication ERR if the data inserted are wrong Button Wizard 61 allow to recall the window of the dip switch wizard Wizard Mode that can be used with device not connected Pag 17 of 20 Picture 17 SWITCH MODE DAT4532D and DAT4632D im Switch Wizard a ioj xi Wizard gt 61 C Reverse tf Direct SREBARBE oe a ek Fe SEE a e SRABARBE a a te Go ote af cee Configuration Check Picture 17 SWITCH MODE DAT4532D and DAT4632D Screenshot e To visualize how the device has been programmed Button View switch 7 Picture 1 read the actual configuration of the dip switches on the device connected the sections of the window will be automatically updated in function of the programming set e To visualize how to configure the device Section Input 83 allow to select the type of signal to apply on input the section SW1 amp SW2 85 will be automatically updated in function of input selected Section Output 84 allow to select the output type for each output channel the sections SW1 amp SW2 85 will be automatically updated in function of the outputs selected Sections SW1 amp S
Download Pdf Manuals
Related Search