WT-1010GPRS - Witura Technology Sdn Bhd
Contents
1. Explanation DEFAULT Jumpers for restoring factory default settings Jumpers for enabling the 3rd operation mode of the device Jumpers for connecting the 2nd operation mode of the device Bl and B2 Jumpers for choosing GSM back up operation mode DEFAULT Jumpers for restoring factory default settings Jumpers for enabling the 3rd operation mode of the device 1 7 LED Indicators Functionality Light Emitting Diodes LED INFO Working mode indicator STATUS Device activity indicator GSM GSM network quality indicator Connection Strength Indicator To identify connection strength GSM indicator is used To ensure the best quality of the network adjust the position of GSM antenna and find the best possible connection by watching the frequency of indicator blinking WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 7 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD ateway GPRS CID It is recommended to install the antenna remotely from communicator panel NOTE Due to GSM network characteristics it is recommended to use the system WT 1010GPRS with the same GSM operator which is used by system users Thus you will ensure the quickest SMS message delivery and receipt NOTE To ensure maximum system operation reliability we recommend do not use Thus you will ensure better quality of audio signal We do not recommend y P y installing the antenna in a metal box prepaid cards If the balance is in2. ITURA technical support by e mail technical witura com More up to date information about your device and other products can be found at the manufacturer s website www witura com WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura conk 4 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD 3M Gateway GPRS CI D Fuse resettable Fl type miniSMDC 500mA Blown fuse cannot be replaced by the user and the replacement fuses have to be exactly the same as indicated by the manufacturer If you use security class computer for setting the parameters it must be connected to earth WT 1010GPRS can be powered direct from 12V battery The battery capacity shouldn t be higher than 7Ah The WEEE Waste Electrical and Electronic Equipment marking on this product see left or its documentation indicates that in the EU the product must not be disposed of together with household waste Fa Fa w About User Manual This document describes communicator WT 1010GPRS its operation and installation It is very important to read User Manual before start using the system A quick start guide is located in first two chapters l General Information Communicator WT 1010GPRS is a device for transferring information from the Alarm Control Panel to the monitoring station via GSM audio connection channel or and users via SMS message The system can be used in the following applications e Property security e Backup PSTN li
3. The device decodes the data sent via Indicator is lit CONTACT ID protocol to textual user For WT 1010GPRS use with no landline understandable information 1 Connect the circuit as shown in Fig No 2 connect telephone input of the Alarm Control Panel RING TIP to RING TIP connectors of communicator WT 1010GPRS 2 Connect power supply to DC COM pins Power supply is usually used as AUX and AUX output of Alarm Control Panel 3 The system should start in less than a minute GSM LED indicator should be blinking or be ON indicating connection to GSM network WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 8 WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 9 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD
4. WT 1010GPRS GSM Gateway GPRS CID User Manual Gateway GPRS CID Safety Instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around e GSM communicator gateway WT 1010GPRS further referenced as system or device contains a radio transceiver operating in GSM850 900 1800 1900Mhz Don t use the system where it can interfere with other devices and cause any potential danger Don t use the system with medical devices if this is required in the manual of the medical device Don t use the system in hazardous environment Don t expose the system to high humidity chemical environment or mechanical impacts Don t attempt to personally repair the system System labeling sticker is at the bottom of the device System WT 1010GPRS is a device mounted in limited access areas Any system repairs must be done only by qualified safety aware personnel Mains power must be disconnected before any installation or tuning work starts The system installation or maintenance must not be done during stormy conditions The system must be powered by main 10 24V 300mA power supply which must be approved by LST EN 60950 1 standard and be easily accessible External power supply can be connected to AC mains only inside installation room with automatic 2 pole circuit breaker capable of disconnecting circuit in the event of short circuit or over current condition Open
5. circuit breaker must have a gap between connections of more than 3mm Any additional devices linked to the system WT 1010GPRS computer sensors relays etc must be approved by LST EN 60950 1 standard WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 2 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD 572 WITURA Configuration Tool Program System configuration is performed by using program software WITURA Configuration Tool that can be downloaded from internet website www witura com Before connecting the cable to the computer via USB port read WITURA Configuration Tool user manual that can be found in HELP section of the program 3 3 Technical Support no external power supply Indicator STATUS is off and not blinking circuit not properly connected blown fuse no network signal SIM card is not inserted SIM card PIN code request has not been disabled SIM card not active Indicator STATUS is blinking several times per second SIM card account depleted incorrect SMS central number no network signal user telephone number is not programmed in System does not deliver users list any SMS messages user telephone number is indicated improperly read more about it in WT 1010GPRS Configuration Tool user manual which can be found in Help section of the program If your problem could not be fixed by the self guide above please contact your distributor or W
6. cts are switched direct to the PSTN landline and the WT 1010GPRS communicator just monitors the PSTN landline In case of PSTN failure WT 1010GPRS switches the Alarm Control Panel s Ring amp Tip contacts to the GSM network and all communication goes to the Alarm receiving centre ARC through GSM voice short circuited When this operation mode is used the information about the secured object is received by the user users as well as alarm r ET receiving centre ARC Device retransmits the data sent from 00 MODE the Alarm Control Panel via CONTACT ID protocol to the ARC OO PROG and decodes this data to user understandable text and sends it via SMS message indicator INFO informs only about decoding The text is created by the user This decoding is performed according to the preset parameters which can be specified by the user only by using the program WITURA Configuration Tool for more information please refer to user manual of this program SMS messages can be received by up to 5 users e Backup Mode 2 WT 1010GPRS is connected to PSTN landline via PBX station If this mode is enabled the Alarm Control Panel s Ring amp Tip contacts are switched by WT 1010GPRS direct to the PBX station internal line Then the signal initiated by the Alarm Control Panel for the Alarm Receiving Centre ARC is routed via the PBX to an external PSTN landline The WT J 1010GPRS communicator only monitors that the external PSTN landline i
7. ecurity service on the Alarm Control Panel when you do not need to transmit data to security service and you are using only SMS messaging mode In such a case you can use any telephone number you can use the number consisting of one digit 2 1 1 Monitoring Station Mode If you want the device to operate in Monitoring station mode you must ensure that all Jumpers SET MODE PROG are not used OOJ ser When this mode is enabled communicator WT 1010GPRS only OO MODE retransmits data sent from Alarm Control Panel via CONTACT OO PROG ID or 4 2 protocol to security service panel via GSM voice channel WT 1010GPRS does not require any additional configurations 2 1 2 SMS Message Mode This operation mode is enabled by putting a jumper on MODE connectors in connector group SET MODE PROG as demonstrated in the example Other connectors must not be short circuited When this operation mode is used the information about the _ sbi secured object is delivered only to user users and alarm receiving centre is not informed In this case WT 1010GPRS decodes the data sent from the Alarm Control Panel via CONTACT ID protocol to user understandable text and sends it WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura conk 2 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD M Gateway GPRS CID WT 1010GPRS can operate in 3 communication modes i e e Transmits information from the Alarm Control Panel to the monitoring
8. ion via GSM voice as well as to registered users via SMS message This chapter describes pre operation and system operation when each of the above mentioned modes is enabled WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura conk L COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD teway GPRS CID LI L2 L3 L4 RING TIP N C DC COM N C N C N C rente RING TIP AUX AUX ALARM CONTROL PANEL Fig No2 For WT 1010GPRS use with landline backup mode 1 1 Connect the circuit as shown in Fig No 3 connect telephone input of the Alarm Control Panel RING TIP to RING TIP connectors of communicator WT 1010GPRS 2 Connect L3 amp L4 pins to external landline PSTN 3 Put Jumpers BI amp B2 4 Connect power supply to DC COM pins Power supply is usually used as AUX and AUX output of Alarm Control Panel 5 The system should start in less than a minute GSM LED indicator should be blinking or be ON indicating connection to GSM network LF 12 13 L4 RING TIP N C DC COM N C N C N C To landline RING TIP AUX AUX PSTN ALARM CONTROL PANEL Fig No3 WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura conk COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD 1 6 J umpers Functionality Gateway GPRS CID Connector Functionality recs Poner supp posare anne COM Commoncontact sd Common contact contact e wi Spe O Not connected Labeling
9. ne using GSM network WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 3 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD M Gateway GPRS CID 1 2 Operation Description via SMS message This decoding is performed according to the preset parameters which can be specified by the user only by using the program WITURA Configuration Tool for more information please refer to user manual of this program SMS messages can be received by up to 5 users WT 1010GPRS provides a dial tone and fully replaces a telephone landline PSTN for Alarm Control Panel reporting to the central monitoring station when telephone line is unavailable or has been cut or disconnected by PSTN provider WT 1010GPRS supports only outgoing calls DTMF number dialing mode in alarm control panel must be enabled 2 1 3 Combined Monitoring Station Mode And SMS Message Mode Can detect temporary service suspension by the service provider for technical or billing reasons even if a dial tone is still present Option available only for WT This operation mode is enabled by putting a jumper on SET 1010GPRS version connectors in connector group SET MODE PROG as demonstrated in the example Other connectors must not be Communicator WT 1010GPRS backup function can work in 2 modes Backup Mode 1 WT 1010GPRS is connected direct to PSTN landline If this mode is enabled the Alarm Control Panel s Ring amp Tip conta
10. s _ connected to the PBX and does not monitor the internal line In the case of external PSTN failure the PBX still provides a dial tone but WT 1010GPRS switches the Alarm Control Panel s Ring amp Tip contacts to the GSM network and all communication goes to the ARC through GSM voice This 3 1 Restoring Factory Default Parameters To restore factory default parameters e disconnect power supply and USB from PC in case it was connected e short circuit connect connectors DEFAULT e connect power supply for 5 seconds mode is used for sites where the internal telephone lines are sufficiently protected by the alarm system but where it is impossible for the alarm system to protect the external PSTN landlines and ensure they are e disconnect power supply connected to the PBX disconnect connectors DEFAULT WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 4 WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura cork gt COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD Gateway GPRS CID ATTENTION On the Alarm Control Panel you should enable tonal DTMF number dialing mode activate CONTACT ID or 4 2 data transmission protocol and enter telephone number of Alarm receiving centre with geographic area or international code E g For UK London 020xxxxxxxx Or 004420xxxxxxxx ATTENTION it is also necessary to enter telephone number of s
11. station via GSM voice e Transmits information from the Alarm Control Panel only to the registered users via SMS message e Transmits information from the Alarm Control Panel to the monitoring station via GSM voice as well as to registered users via SMS message A computer program WITURA Configuration Tool is used for configurations which are necessary for the system to operate in the second and third modes i e to send SMS messages to the registered users The device is connected to the computer via USB connection 1 3 Technical Specifications Electrical And Mechanical Specifications Supply voltage 10 24V 300mA max Current used in standby mode 120mA max GSM Modem Frequency GSM850 900 1800 1900 MHz Supported Protocols CONTACT ID 4 2 Maximum number of users to whom SMS messages are delivered 5 Dimensions 130x73 mm Operating Temperature Range 20 550C Generated phone line voltage 18V Generated phone line current 25mA Generated phone line impedance 600 Ohm Dial tone of generated phone line 350 Hz When SMS mode is enabled system doesn t support 4 2 protocol 4 2 protocol works only with Monitoring Station Mode WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 5 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD 1 4 Block Circuit SIM CARD GSM MODEM For configurations BI B2 FUSE 500 mA Li 2 GB L4 RING TIP N C DC COM NC NC NC 1 5 Connectors Functionali
12. sufficient the system will not be able to inform users about the alarm Device Activity Indication No power supply or some fault is present Blinking several times per second IMPORTANT Power supply at Alarm Control Panel must be disconnected before any installation or tuning work SIM card is used improperly is not used The system can be installed in a metal or non flammable plastic enclosure together with alarm control panel When the metal box is also used it is The device decodes the data sent via Indicator is lit CONTACT ID protocol to textual user i s ion understandable information necessary to ground the box using yellow green color cable For the connectio use 0 50 mm2 1 thread cable Working Mode Indication INFO indicator blinkina cok Device installation and Pre operation INFO indicator blinking Meaning 1 Fasten the system in the enclosure using fastening holders On Fne device Is In passive moe 2 Place SIM card into the holder but make sure that SIM card PIN code is The device retransmits the data sent from disabled PIN code can be disabled by putting SIM card into mobile phone Blinking several times per Security Control Panel to the panel of and following proper menus SIM card should not have any remaining SMS second security service this indication is possible messages then device is working in first mode 3 Connect the antenna the device cannot be turned on without antenna
13. ty Main Units GSM MODEM GSM network 850 900 1800 1900 MHz modem SIM CARD SIM card holder ANT GSM antenna SMA type connector FUSE Resettable Fl type miniSMDC 500mA WT 1010GPRS USER MANUAL Rev1 0 Technical Support technical witura com 6 COPYRIGHT 2011 WITURA TECHNOLOGY SDN BHD M Gateway GPRS CID For WT 1010GPRS use with PBX amp landline backup mode 2 1 Connect the circuit as shown in Fig No 4 connect telephone input of the Alarm Control Panel RING TIP to RING TIP connectors of communicator WT 1010GPRS Connect L1 amp L2 pins to external landline PSTN Connect L3 amp L4 pins to Internal PBX line Remove Jumpers Bl amp B2 re 2 SS Connect power supply to DC COM pins Power supply is usually used as AUX and AUX output of Alarm Control Panel 6 The system should start in less than a minute GSM LED indicator should be blinking or be ON indicating connection to GSM network 1 2 53 L4 RING TIP N C DC COM N C N C NC RING TIP AUX AUX To landline PSTN ALARM CONTROL PANEL Internal Tel line Fig No 4 2 System Pre operation 2 1 Operation Modes WT 1010GPRS can operate in 3 modes i e e Transmits information from the Alarm Control Panel to the monitoring station via GSM voice e Transmits information from the Alarm Control Panel only to the registered users via SMS message e Transmits information from the Alarm Control Panel to the monitoring stat
Download Pdf Manuals
Related Search