IQ Control Module 635501 - securityhelpdesk.com.au
Contents
1. or 0 Int Siren at Address 802 Maximum switched current 200 mA Minimum Cable spec 14 0 2 CAUTION 2 bata Total current sourced from T5 OUT1 amp DET Strobe DET and LAN must not Auxiliary 1 Output l exceed 600mA Normally used for Strobe e g Assign Auxiliary Event Type 1 at Address 801 H Maximum switched current 200 mA Minimum Cable spec 14 0 2 T5 SPK amp DET4 Siren Speaker output Maximum load 8 Ohms Minimum Speaker rating 10 Watts i e 1 x 8 Ohm Speaker only Additional speakers must not be connected in parallel Siren cover Tamper switch Normally Closed Minimum Cable spec 14 0 2 NOTE A 6k8 Resistor must be connected between SPK amp DET if Siren speaker not connected Battery cable supplied T3 4 amp 12V Sealed Lead Acid Battery connection Maximum Battery capacity 7 AH T1 AC 16V AC Input Connect Green Yellow Earth wire to T3 Plug Pack and cable color may vary outside Australia Port 0 amp Port 1 995502 IQ Plus only Serial ee ee ee ee ee es an ei TTL Comms Port connect Prog Key Port 0 only RS232 PC connection requires adapter cable 993030 or Printer connection IQ Plus only adapter cable 993030DB25 re Disclaimer 1 The manufacturer amp or it s agents take no responsibility for any damage financial loss or injury caused t2. to other equipment se a o 4 Normally Open Alarm Contacts e g As often found on Smoke Detectors are Sata 604 Cable from a 6 wired in the same manner as Normally ontro Concept IQ _________ Closed contacts Module Supplied When programming the Zone Input 1 ee oe we 5 Option 7 Normally Open in the Zone Zs Cal Options must be selected Addresses 2 2 a PSTN 651 Zone 1 to 666 Zone 16 fom Line one en eo 6 Ne o gt JP9 p4 Control Module Rev 1 0 05 03 CONCEPT IQ Installation Manual Connection Details Power Warning devices amp LAN po ads JP10 DTMF Voice rss 6 gim Card Port Q T8 Aux LAN For temporary connection of a Terminal for diagnostic purposes ach H as Er ia la 2 e enm EEE HEE UO j f H 0 H m ne i T9 Zone Input re L f zs Auxiliary Output oes TEAREN posses Expansion Bus Port AC a o 23 ZN1_OV_ZN2_ZN3_OV_ZN4 hes ha Ow A 4 Ov J res E TN Earth L nyen T4 LAN connections to Terminals Up to 4 Maximum run to furthest LAN Module 100m Total LAN cabling 150m maximum If twisted pair cable is used DO NOT combine Clock amp Data on the same pair 4 Core Security Cable recommended 14 0 2 T5 OUT2 amp DET Auxiliary 2 Output General purpose Aux May be used for Piezo Siren e g Program Aux 2 as Auxiliary Event Type 9 Ext Siren
3. CONCEPT IQ Installation Manual Control Module Rev 1 0 5 03 pl Control Module 995501 995502 Contents Control Mod le Parts List zsinatra RRA 1 Specifications z2r hieni eni a n aeaea ai i irt O AAN a 1 Installation PrOC QUre es snini aaaeaii E E REEE EEEE 2 Connection Details Zone Inputs Detectors Tamper switch and Fuses ssssscscscirrene 3 Mode 3 Telephone line connection oo eee eeeeeeeeeeeeeeeeeeeneeeeeaeeeeeeaeeeaeeeaesaeesaeeeaesneeeaeeeaeeaeeeaeeeas 3 Connection Details Power Warning devices amp LAN 0 ccccccecceseceeeeeeeeseeeeeeeeeeeeeeeteeeseneesenees 4 Control Module Parts List Control Module PCB mounted in metal enclosure User Manual Installation Manual This document Installation Kit containing Contents may vary outside Australia 4x Pan Head Self tapping screws 4x6mm Used to secure the enclosure cover 5 x plastic D bungs Must be fitted to all unused cable entry cutouts in the cover Telecom Line cord Note Non standard configuration Only suitable for use with this product 10 x 3k3 End of line resistors orange orange black brown brown Used for Single EOL Dual EOL Zone Doubling 10 x 6k8 End of line resistors blue grey black brown brown Used for Dual EOL or Zone Doubling 10 x 1k End of line resistors brown black black brown brown Used for Zone Doubling Tamper switch Tamper switch bracket 2 x 6 Way plug on screw terminals Only for PCBs that do not h
4. Continuous Operating Temperature 0to 50 C Storage Temperature 20 to 70 C Relative Humidity Non condensing 15 to 85 2003 Inner Range Pty Ltd Part No 635501V2 p2 Control Module Rev 1 0 05 03 CONCEPTIQ Installation Manual Installation Procedure 1 Top mounting holes x2 Step 4 Port 1 Serial Comms Port 995502 IQ Plus only Prog Key or PC or Printer Port 0 Serial Comms Port Prog Key or PC T1 16V AC Power connections Step 5 T3 Battery connections Step 6 Rear cable entry cutout Installer The system must be installed and maintained by a competent qualified installer who holds appropriate licences for Telecommunications and Security System cabling in accordance with local Regulations Location The Control Module must be installed in a secure location near an AC Power outlet and Telephone line connection Install the unit where it will not be subject to temperature or humidity outside the specified range and will not come into contact with water other liquids high dust levels or chemical atmospheres Adequate ventilation must be provided around the cabinet 50mm min to ensure that heat from any other source does not cause the Control Module to operate at an unsafe temperature Positioning Orientation of the cabinet MUST be as per the illustration below with the battery at the bottom Fit the Tamper switch into the hole provided in the Tamper switch bracket The Tamper switch b
5. H Battery position Step 7 12V 7AH Step 6 Bottom Mounting Holes x 2 Step 4 lt Location of Side Cable entries Step 7 CONCEPT IQ Installation Manual Control Module Rev 1 0 5 03 p3 Connection Details Detectors Tamper switch and Fuses wo TE ne B Co ini Q Ce o F2 PWR Fuse 1A M205 COn a T EEE F H J 7 H al eooo lecccloe Eor AA ecccce lee S S e7 QO z 2 3 3 A w Y t ae Be oy A t OV 4 TAMP O T2 TAMP Dedicated Cabinet Tamper input Tamper switch supplied No End of line resistors necessary Detector T6 and T7 Zone Input connections C I Tam Single End of Line l e g Alarm 3k3 Seal ae Open Cct Alarm r detector 2 Dual _End of Line Tamo e g ae 3K3 Seal i 10k1 Alarm Alarm Open Cct Tamper Gs Short Cct Tamper Ist Detector 2nd Detector Zone Doubling 1k Seal NOTE 4k3 1st Zone in Alarm The 1k EOL 7k8 2nd Zone in Alarm Resistor must 11k1 1st amp 2nd Zones in Alarm be fitted at the Open Cct Tamper 2nd Detector Short Cet Tamper T5 DET and OV Detector Power connections 12V Supply for Detectors and Auxiliary Devices Total combined current sourced from DET and LAN must not exceed 600 milliAmps Minimum Cable spec 14 0 2 Mode 3 Telephone Socket Wiring for Australia NOTE Zone Input connections 604 Socket J 2 Normally Open Alarm Contacts
6. ave fixed terminal blocks fitted 1x 3 Way plug on screw terminals Only for PCBs that do not have fixed terminal blocks fitted 5 x 2 Way plug on screw terminals Only for PCBs that do not have fixed terminal blocks fitted 2x 6 3mm Tamper switch connectors Battery connection lead 220mm pre assembled 1x2 Amp M205 20mm Fuse Spare Electrical Specifications Power Supply I P Plug pack Mains Supply 240V AC 10 10 50 Hertz Plug pack Output 16V AC 1 0 Amperes PCB AC Input Voltage 16V AC Battery Capacity 12V 7AH Sealed Lead Acid Battery DC Operating Voltage Batt I P 9 5 to 14 V DC Low Battery alarm activated at 11 2V 0 3V Battery Input Fuse F1 5 Ampere Power Supply O P Current Total combined current required by devices connected to DET and LAN must not exceed 600 milliAmps Fuse Protection F2 2 Ampere DET and LAN Auxiliary Outputs OUT1 Strobe OUT2 Max switched current 200mA per Auxiliary Open Collector Siren Output SPK Maximum Load 8 Ohms i e 1 x 8 Ohm Speaker only Additional speakers must not be connected in parallel NOTES 1 ALWAYS REPLACE FUSES WITH THE SAME FUSE TYPE AND VALUE 2 See data supplied with detectors and output devices for current consumption Mechanical Specifications Dimensions Height 260 mm Width 265 mm Depth 80 mm Weight 4 2 kg Cabinet amp cover PCB and 7AH battery Plug pack 0 6kg Environmental Specifications
7. he appropriate Standards for Security and Telecommunications systems Cables must be protected at the entry points by grommets or by allowing the conduit to protrude into the cabinet The D Bungs provided must be fitted to all unused cable entry cutouts DO NOT connect the LAN CLK amp DATA wires to the Control Module until all LAN Modules e g LED Terminals are Commissioned Diagnostics The STATUS Lamp on the Control Module can be used to assist with troubleshooting and testing SLOW FLASHING MicroProcessor OK Running FAST FLASHING Controller is Dialing NOT FLASHING MicroProcessor Not running OR Programming Key Upload or Download in progress Cover In order to comply with regulations the cover must always be correctly re fitted following any installation or maintenance work Engage the hinges on the Left hand side and fasten the cover tightly to the cabinet using all four 4 of the screws provided Screw holes are located on both edges of the two Right hand side corners STATUS Lamp Step 8 JP9 Mode 3 Line Socket for connection to Telecom Line Special cable supplied must be used 2 eo et Tamper switch bracket j n ane ai and Battery retainer Ol 2 Step 3 Latch for optional lock 12V 7A
8. o any equipment property or persons resulting from the correct or incorrect use of the system or it s peripherals The purchaser assumes all responsibility in the use of the system and it s peripherals 2 While every effort has been made to ensure the accuracy of this manual the manufacturer assumes no responsibility or liability for any errors or omissions Due to ongoing development this manual is subject to change without notice
9. racket must be positioned in the slot provided and under the base of the cabinet before the cabinet is secured to the wall When wired to the TAMP input Tamper switch alarms if the cabinet is removed from the wall or the cover is opened Mounting The cabinet must be secured to a flat solid vertical surface using appropriate fasteners through the 4 holes provided in the base and must be positioned to provide unhindered access for installation and maintenance The two mounting holes in the top of the cabinet are keyhole slots to assist with positioning When mounting onto flammable surfaces a fire protection backplate MUST BE INSTALLED Power Plug Pack and cable color may vary outside Australia Strip 5mm of insulation from the ends of the 3 Plug pack cable conductors Terminate the 16VAC conductors into the AC Input connections and the Earth wire Green Yellow into BATT on the PCB CAUTION Do not connect the Plug pack to an AC outlet until all wiring is complete and checked Battery Connect the pre assembled battery cable into the BATT and BATT connections on the PCB CAUTION Do not connect the Terminals to the Battery until all wiring is complete and checked Cabling All cabling must enter the cabinet via the existing cutouts provided in the rear and sides Additional holes must not be cut in the cabinet Installation of Cables both inside the cabinet and external to the cabinet must conform to t
Download Pdf Manuals
Related Search