Installation and User Manual (Version 1)
Contents
1. Notice to Consumer This warranty gives you specific legal rights and you may have other rights which may vary from province to province The provisions contained in this warranty are not intended to limit modify take away from disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation 182. a flat surface the head roll tube components A B C D and X e The head roll tube idle end D middle section A and motor end B are supposed to be a tight fit with each other Connect the pieces of tube ensuring that the Velcro lines up with each piece Fig 1 10 e The Top Joiner X will slide over the head roll tube e Using the self drilling screws J fasten the Top Joiner to the head roll tube and the joiner inside the head roll tube Fig 1 11 e Tilt the motor end of the unit upwards to empty the shavings out of the opposite end of head roll tube e Fasten the idler end C to the head roll idler end D tube with the self drilling screws J The tube has pre marked holes Fig 1 10 Step 4 Bracket Location and Assembly e Determine which end you prefer to have the motor at left or right depending on your power supply e There isa star bracket S and a drop in bracket N T the star bracket is the end that the motor will sit in You will need to fasten the drop in bracket such that the opening is facing up this will depend on which end you decide to have your power source e Using the measuring wire O given attach each end to the brackets using a cottor pin fig 1 12 e Span the brackets on each side of the garage untill the wire is at max tention and Note Ensure that in this area there are no obstructions as this is where the headroll will eventually be mounted e Attach bot
3. CICEN Protective Garage Door Barrier Installation and User Manual Version 1 ATTENTION Read these materials prior to assembling and using The SportScreen Table of Contents SOCON T a Introduction amp General Information Product Information ccc ecccceesesesecescescescceccecesccecesccecescesseecescescescescusesecusevecuscuseeseusesecs 3 ACCO OE a mere ne re eC ee cree ee 3 FO T ee uentayscannmsiensanavsaeeus tamed E EEE 4 SUN 2 cers accct nosed ens teesctesteo teanteteee Assembly and Installation Instructions VS CNN tect oes escent E nee sees wee eee eeeesen E E se gdtances 4 PU SD Ie EON cette ste pois E E wer Seen edema rete see T T 4 MEG GES N CCC sings cece ces ee ca cateeeec san E E E E EE scare e egesanapaiesenee 4 PSS ONO ca EAEE AE AE TA A E A PE S A EAA EN E 5 14 SOC E EEAS R User Warning Information User Warning NformatiO satsin ae aN 15 Secho Fe Care and Maintenance Instructions Cold Weather PVOLOCE OM ste isstecetisstcedces csinceiap as sass annesecveueatit A E EN 16 Replacement AEE See tees sreoscscsevstacecreonasadcesesaaasactesnsncninanssesosuaeonteetupaatecconstetantantseeanenecanntce 16 Sale VONE RUES eee eee ene nar et race Een Sune ne Peer ne nen oe er 16 oot it 6 Ms E eee ne er ee eee ee eee ee Warranty Information NY AEE AY UI TOMI CVO a arses corsonccrtavaacanaapssnnunavcataeoiacucaias savetvasesaseusle ssaneniauasaneaaesaestomneniatennaniadeeene 17 Section 1 Introduction amp General Infor
4. already pre programmed with your Sportscreen motor Simply install the battery into the back of your remote Fig 1 17 If you want to add a second third or fourth remote visit www thesportscreen ca Fig 1 16 f for some reason your remote is not programmed or you have purchased a spare remote follow these steps 1 Unplug unit 2 Hold Up button 5 seconds 3 Plug unit back in while still holding up button 4 Listen for beeping from motor 5 As motor is beeping rapidly press up button 12 Step 9 Setting Your Upper and Lower Limits e The limit sets how high or low the SportScreen will roll when you use the remotes e The limit adjusting wand R is used for setting your upper and lower limits Fig 1 18 Fig 1 17 The above pictures are the underside of the headtube looking up e the power cord should be coming out of the motor on the bottom of the tube e There is an adjusting screw on either side of the power cord 13 Motor Mounted on Left Side Adjusting Limit For Up l Adjust clockwise Rounding UP Adjust counter P clockwise to increase to reduce the upward travel upward travel Rounding DOWN Adjusting Limit For Down Adjust r E Adjust Clockwise to reduce Counter downward travel Clockwise to increase downward travel ESEN mae otor Mount on Right Side Adjust Limit For Up Adjust counter Adjust clockwise clockwise to increase Rounding UP to reduce the upward tr
5. avel upward travel oll Rounding y Adjusting Limit For Down Adjust Counter Clockwise Adjust i Clockwise to to increase downward reduce travel downward travel e Continue this process until the net is at the desired level When it is fully lowered the net should be tight and the bar almost touching the ground but low enough to stop a hockey puck from sliding under When it is fully raised up the bottom bar should be tucked right below the tube 14 Step 10 Display Warnings o A take the warning information sticker and stick it on the back of the Sportscreen s windbar pocket Display the warning information sign U either inside or near your garage to ensure users remain safe and are aware of any dangers Section 3 User Warning Information When shooting pucks please ensure that everyone in the area is wearing a hockey helmet and cage to prevent serious injuries to the head or face Many users of The SportScreen are children and therefore need some supervision when using it especially during the lowering and raising processes Due to the danger of children chasing rebounding balls and pucks into the street we strongly urge that you purchase The SportCurb to protect users and contain balls pucks in the driveway Make sure to supervise your children during use When lowering or raising The SportScreen ensure that no one is touching or holding onto it There is the chance that fingers or other appendag
6. ection 4 Care and Maintenance The SportScreen is made using heavy duty materials and is finely crafted to provide you and your family with many years of enjoyment and service Proper maintenance and care will help to prolong the life of your SportScreen Cold Weather Protection The SportScreen is designed for year round outdoor use However in climates of cold weather where snow and ice are common we recommend that any built up snow and or ice be removed before use to ensure it does not interfere with lowering or raising The SportScreen Do not use a sharp object such as a shovel hoe garden rake etc to remove ice or snow as this may damage The SportScreen or interfere with proper operation Replacement Parts Although The SportScreen is made of extremely heavy duty and durable components some parts may eventually need to be replaced All replacements should be ordered through The Sport Screen Ltd Call 1 855 727 3360 if you need replacement parts or have any questions If any warning signs or labels become unreadable for whatever reason call The SportScreen Ltd for replacements as well 16 Safety Checklist Rules It is the responsibility of the owner to become familiar with the safety rules and to convey these rules to all users A Ensure that no one is below The SportScreen as it is being lowered A Make sure no one is hanging onto The SportScreen as it is being raised or lowered A Do not shoot balls or pucks at anyone stand
7. es could get caught or pinched in the SportScreen if they interfere with the process Users should ensure that no person or objects are hanging or suspended from The SportScreen Although the brackets are rated to 300 Ibs if children or adults hang from The SportScreen it could damage the product and cause possible harm to users Be careful when shooting pucks balls at The SportScreen when other people are present Do not shoot pucks or balls if anyone is standing less than 2 feet behind the screen This is simply a precaution since someone could be seriously injured if they are standing directly behind The SportScreen and are hit with a puck ball When shooting pucks or other hard objects at The SportScreen ensure that no one is standing in the immediate vicinity as they could be seriously injured by stray balls pucks 15 The SportScreen Ltd assumes no liability for improper installation or any injuries that result When rolling down The SportScreen make sure that your automobile is not directly under it as it can cause damage and scrapes to the vehicle Ensure that those shooting pucks are aware of their surroundings and understand that shooting pucks can cause serious injuries to people pets Be careful of rebounding pucks off of metal nets as these pucks can cause damage to property and vehicles as well as people or pets This is why we recommend that in tight spaces you use duct tape to outline nets and targets S
8. ft motor end right REMOTE BATTERY AND HOLDER MOTOR ADJUSTING WAND STAR BRACKET DROP IN BRACKET USERS MANUAL WARNING LABLE SCREEN HEAD ROLL TOP JOINER eS eS 1 38 big 4 small SS SS E A NOTE FASTENERS ARE NOT PROVIDED FASTENERS CAN BE PURCHASED AT ANY LOCAL HARDWARE STORE PLEASE CONSULT WITH THE SALES REPRESENTATIVE AT THE HARDWARE STORE IT IS THE CUSTOMERS RESPONSIBILITY TO ENSURE THE SPORT SCREEN MOUNTING BRACKETS ARE PROPERLY FASTENED TO THE MOUNTING SURFACE PLEASE CONSULT A PROFFESSIONAL INSTALLER IF NEEDED Step 2 Mounting Options Surface or Under Eaves Surface Mount Under Eaves Mount X oo o Ry ROOF TER e R eT r Pri i z2 RLS ee en OXKKY te VO y OS Gree A d IONIN Fig 1 5 Ensure mounting height is 8 10 or lower For higher mountings contact customer service for a custom built unit The Surface Mount is used for screens that are mounted directly on the surface of the building Figure 1 4 amp 1 9 via AN Fig 1 9 NOTE WOOD MOUNTING SCREW AND OTHER FASTENERS ARE NOT PROVIDED FASTENERS CAN BE PURCHASED AT ANY LOCAL HARDWARE STORE ITIS THE CUSTOMERS RESPONSIBILITY TO ENSURE SY D THE SPORT SCREEN MOUNTING BRACKETS EN ARE PROPERLY FASTENED TO THE or MOUNTING SURFACE PLEASE CONSULT A PROFFESSIONAL INSTALLER IF NEEDED e A m v0 X t 1i Step 3 Headroll Tube Assembly e Lay outon
9. h brackets to the wall but leave them fairly loose for adjustments later e With one installer at each end and ladders in place lift the entire assembly up into the desired location The motor end must be inserted first A Make sure that the wire on the motor end faces downwards so that water and ice S amp S will not funnel into the motor Fig 1 13 Fig 1 14 Fig 1 12 to e Take the idle end L and insert it into the bracket and move the bracket until it is secure in the slotted grove Fig 1 14 A Make sure the cotter pins are properly installed at each end to prevent the head roll assembly from falling out of the bracket Cotter pin must go through the hole with the square shaft of the motor end Step 5 Mounting the Screen e The Screen W is to roll off the front of the head roll tube e Take your SportScreen and loop it up over the front of the tube This requires 2 people to do as the weight of the screen will make it difficult to attach the Velcro by one s self e When securing the screen to the head roll tube make sure that the curtain is evenly attached and straight across the tube This ensures that when The SportScreen rolls up it does so evenly If it is not attached evenly or horizontally it will NOT roll up properly Step 6 Assembling amp Inserting Mid Bar and Bottom Bar e Join the 3 mid bar sections H and together by sliding the outer rods over the preinstalled joiner section in the m
10. id bar middle section I e Use the smaller self drilling screws J in the pilot holes to connect the rods together e Insert this newly assembled mid bar through the pocket at the center of the screen e Fit the two mid bar end caps L onto both sides of the newly assembled mid bar e Join the 3 bottom bar sections E F and G together by sliding the tapered ends into the larger diameter ends e Using the larger self drilling screws J and the pilot holes attach the bars together e Insert this newly assembled bottom bar through the pocket at the bottom of the screen e Using ahammer tap the two bottom bar end caps K onto both sides of the newly assembled bottom bar 10 Step 7 Wiring Your SportScreen e If you would like to have your wire fed through your house drill a hole into your house from your garage using a minimum 3 8 clearance drill bit Fig 1 15 e Once your SportScreen is mounted take the cord from the end of the motor and feed it through the hole into your garage Fig 1 15 Fig 1 15 A Make sure that the wire on the motor end faces downwards so that water and ice will not funnel into the motor e Once the wire is through the wall attach the yellow wall plug M wiring the green wire to the green and the other two to either end Fig 1 16 Fig 1 16 NOTE MAKE SURE THE CORDS ARE INSIDE OF THE YELLOW WALL PLUG 11 Step 8 Programming your Remote Control Your Sportscreen remote control is
11. ing behind The SportScreen A Check to make sure that there are no holes or tears in The SportScreen prior to use Section 5 Warranty Information This SportScreen product is guaranteed for 2 years from the date of original retail purchase against defects in materials and workmanship Subject to limitations and conditions described below this product if returned to us with proof of purchase within the stated warranty period and if covered under this warranty will be repaired or replaced at our option We will bear the cost of any repair or replacement and any costs of labour relating thereto The warranty is subject to the following limitations and conditions a A bill of sale verifying the purchase and purchase date must be provided b This warranty will not apply to any product or part thereof which is not working or broken or which has become inoperative due to abuse misuse accidental damage neglect or lack of proper installation operation or maintenance as outlined in the applicable owner s manual or operating instructions or which is being used for industrial professional commercial or rental purposes c This warranty will not apply to normal wear and tear or to expendable parts or accessories that may be supplied with the product that are expected to become inoperative or unusable after a seasonable period of use d This warranty will not apply to routine maintenance such as setting the limits or programming of the re
12. mation PRODUCT INFORMATION Congratulations on purchasing your brand new SportScreen We believe that you have purchased the highest quality and most durable sports screen available while allowing you to improve the skills of both yourselves and your children The SportScreen allows you to play in the safety and comfort of your own driveway The SportScreen has been engineered with safety durability and performance in mind and will protect your garage while providing hours of entertainment and exercise The SportScreen is constructed from heavy duty industrial materials and is designed to function year round and thus does not need to be removed during the winter months The SportScreen is made of flame retardant mesh that is also resistant to UV and mold The SportScreen is made of such high quality and durable materials that it is capable of stopping balls and pucks launched by both children and adults A Safe use of The SportScreen also requires adequate knowledge of setup as well as a few precautions Please read this manual thoroughly for key points of safety Misuse and abuse of The SportScreen is dangerous and could potentially cause serious injury The purchaser of this piece of equipment is assuming a degree of risk for which The SportScreen Ltd cannot be held responsible Read this information thoroughly before allowing The SportScreen to be used and also keep this manual available for your review ACCESSORIES The SportSc
13. mote controls without following the Setting Your Upper and Lower Limits and the Programming Your Remote Control sections of our Installation guide 17 e f g h This warranty will not apply where damage is caused by repairs made or attempted by others ie persons not authorized by the manufacturer This warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product unless otherwise specified in writing This warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or any repairs or alterations have been made or attempted by unauthorized persons This warranty will not apply to normal deterioration of the exterior finish such as but not limited to scratches dents paint chips or to any corrosion or discoloring by heat abrasive and chemical cleaners and This warranty will not apply to component parts sold by and identified as the product of another company which shall be covered under the product manufacturer s warranty if any Additional Limitations This warranty applies only to the original purchaser and may not be transferred Neither the retailer nor the manufacturer shall be liable for any other expense loss or damage including without limitation any indirect incidental consequential or exemplary damages arising in connection with the sale use or inability to use this product
14. reen Ltd also offers a series of high quality sports accessories to go with your new SportScreen For a current listing go to www thesportscreen ca FAQ If leave my SportScreen mounted outside during the winter will it be affected by the weather The SportScreen is designed to be able to withstand harsh weather and temperatures However we recommend removing snow buildup from the top of your SportScreen to prevent sagging and to maintain proper function How can I clean my SportScreen and or valance All SportScreens and valances can be cleaned up using a mild dish detergent and water My Sportscreen does not cover my entire 18 5 foot wide garage door opening How do install it for the best coverage and protection possible A center point should be marked on your mounting surface so that you center The Sportscreen correctly with your garage door when mounting If your Sportscreen is 18 5 feet wide that gives you 6 feet of protection on either side of a regulation hockey net and will be plenty of protection when shooting pucks or throwing balls Can program a second remote control to work with my Sportscreen Yes you can order a second or even a third remote on our website in our accessories section You can have up to 4 working remotes with one Sportscreen if you want the convenience of having them in your vehicle when you pull in to your driveway Section 2 Assembly and Installation Instructions DISCLAIMER While it is pos
15. sible to install and mount The SportScreen yourself we recommend that customers hire a professional garage door specialist or a general handyman to complete the installation to ensure proper installation and best possible operation of your SportScreen The SportScreen Ltd assumes no liability for incorrect installation by customers or third party installers PREPARATION We suggest that you assemble your SportScreen in your driveway before installation Additionally it is recommended that you sweep and clean your driveway before beginning TOOLS NEEDED e Ladders e Tape Measure e Level e Marker Pencil e Robertson square head Screwdriver Bit supplied to US customers only e Power Drill Drill Bits e Safety Glasses e Hammer e Fastening Screws ASSEMBLY Step 1 Lay Out All Materials Ensure that you have all the pieces required and laid out Fig 1 1 amp 1 2 ASY hain Cha One aa S varr LP uh Bes sib ou x i 7 r Z J ka g gt d e X Bs Nhe s seen yji i 4 Fig 1 1 DESCRIPTION HEAD ROLL TUBE MIDDLE SECTION HEAD ROLL TUBE MOTOR END IDLER END HEAD ROLL TUBE IDLER END BOTTOM BAR END SECTION BOTTOM BAR MIDDLE SECTION BOTTOM BAR END SECTION MID BAR END SECTION MID BAR MIDDLE SECTION SELF DRILLING SCREWS BOTTOM BAR END CAPS MIDDLE BAR END CAPS WALL PLUG DROP IN BRACKET PIECE AND HARDWARE MEASURING WIRE COTTOR PIN idle end le
Download Pdf Manuals
Related Search