Home

Installation

1. 5 Pull the cable connector though the bushing body into the intercom and clip it into the motherboard connector 6 Move the sealing including the cover along the cable as far as the bushing body or add a plug if necessary 7 Replace and tighten the nut Electric Installation 2 3 2 3 Electric Installation This subsection describes how to connect 2N Helios IP Safety into your Local Area Network LAN and how to connect supply voltage and the electric lock PCB Connectors Fig 2 11 shows the lay out of connectors on the 2N Helios IP Safety printed circuit board PCB Cables accessories and other system components are connected to connectors X1 through X22 X1 l s ff e s r mo le x8 xo VA 7 J A DOOR 12V Figure 2 11 2N Helios IP Safety Connectors PCB Version 530v2 19 Electric Installation 2 3 Description of Connectors Loudspeaker X4 Camera module X5 Button 1 LAN X12 Servicing connector Keypad module X15 Left hand microphone X16 Right hand microphone X17 Relay NO and NC contact 12V 700 mA switched output X19 12V 1A DC power input X22 Tamper switch LED1 2 System status indicators LED3 LAN connection activity indicator LAN Connection 2N Helios IP Safety is connected to the LAN via a RJ 45 terminated connector X11 UTP STP cable of category Cat 5e or hig
2. 932070 932080 932090 BEFO 1211 12V 600 mA BEFO 1221 BEFO 1211MB with momentary pin with mechanical blocking Other Accesories 91341481E 932928E 9137410E 12 V 2 A adapter 12 V transformer External IP relay A stabilised power supply must be used where PoE Supply is not applied Terms and Symbols 1 4 1 4 Terms and Symbols Symbols Safety Warning m Always abide by this information to prevent injury of persons Warning m Always abide by this information to prevent damage to the device Caution m Important information for system functionality Tip m Useful advice Note A m Additional information Description and Installation In this section we describe the 2N Helios IP Safety product and its installation Here is what you can find in this section Before You Start E Mechanical Installation E Electric Installation Before You Start 2 1 2 1 Before You Start Product Completeness Check Please check the contents of your 2N Helios IP Safety delivery 1 2N Helios IP Safety selected model 1 Torx 10 Torx 20 double ended wrench 1 spare sealing for big bushing for a thick cable one hole 1 big blank with nut 1 this manual 1 mounting template 1 CD 4 screws 5x80 mm 4 intelligent 8x50 mm dowels Mounting frame is not included it is sold separately as order no 9152000 Bushing set is the same as for 2N Helios IP Force but bushings are already mounted
3. Technical Parameters 4 1 HID Proximity 125kHz 26bit Robust aluminium cast product RAL 2004 orange 40 C to 55 C 10 95 non condensing 40 C to 70 C 217x109x83 mm 242x136x83 mm incl frame netto max 2 kg brutto max 2 5 kg IP66 IP69 29 Supplementary information This section provides supplementary information on the 2N Helios IP Safety product Here is what you can find in this section m Applicable Directives Laws and Regulations 31 Directives Laws and Regulations 5 1 5 1 Directives Laws and Regulations 2N Helios IP Safety conforms to the following directives and regulations m Directive 1999 5 EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity m Directive 2006 95 EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits m Directive 2004 108 EC of the Council of 15 December 2004 on the harmonisation of the laws of Member States relating to electromagnetic compatibility m Directive 2002 95 EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment EN Regulation EC No 1907 2006 of the European Parliame
4. Technical Parameters In this section we describe the technical parameters of the 2N Helios IP Safety product 27 Technical Parameters 4 1 Technical Parameters Signalling protocol Buttons Audio Button design Count of buttons Numerical keypad Microphone Amplifier Loudspeaker Volume control Full duplex Audio stream Protocols Codecs Camera Sensor Resolution Picture frequency Sensitivity Viewing angle Infrared illumination Video stream Protocols Codecs IP camera function Interface Power supply PoE LAN Recommended cabling Passive switch Active switch output RFID card reader Supported cards SIP UDP Industrial waterproof stainless steel vandal resistant pushbutton blue backlit 1 2 on request on request 2 integrated microphones 10W class D 1W optionally 10W Adjustable with automatic adaptive mode Yes AEC RTP RTSP G 711 G 729 on request 1 4 colour CMOS 640 H x 480 V Up to 30 snaps s 1 9 V lux sec 550nm 135 H 109 V Yes RTP RTSP HTTP H 263 H 264 MPEG 4 M JPEG Yes 12V 15 1A DC or PoE PoE 802 3af Class 0 12 95W 10 100BASE TX s Auto MDIX RJ 45 Cat 5e or higher NO and NC contacts up to 30V 1A AC DC 12V 700mA DC optional EM 40XX 125Khz 4 1 28 Mechanical properties Cover Colour Working temperature Working relative humidity Storing temperature Dimensions Weight Covering level
5. and steel structures entry barrier columns etc The frame is not used Caution If there is a risk of vandalism in public garages e g use steel fixing elements instead of the dowels and screws included in the delivery Be sure to insert plugs into unused bushing holes to avoid water leakage during facade cleaning for example Never leave the holes open for even a short time one day delay between mounting and cable connection e g Eliminate the risk of accident Wall mounting is not suitable for narrow passages or places where people s attention may be distracted The manufacturer shall not be liable for injuries incurred as a result of unsafe mounting 1 Select the 2N Helios IP Safety position with respect to the supply cables Where the cables are installed inside a structure or wall use the hole at the intercom bottom 2 Drill holes of the depth of 60 mm for dowels in the wall as shown in the a figure Push or hammer the enclosed dowels into the drilled holes Use BM some suitable building adhesive if the dowels are too loose Use fixing elements of your own for steel structure surface mounting metric screws nuts e g 3 Remove the front panel from the intercom 4 2N Helios IP Safety has bushings already mounted Replace it with OD les s plugs if unused 5 Put the intercom on the wall structure while introducing cables inside Leave 1 some of the cables inside the un
6. undue application and disobedience of the recommendations and warnings in contradiction herewith Any use or connection of the product other than those included herein shall be considered undue and the manufacturer shall not be liable for any conseguences arisen as a result of such misconduct Moreover the manufacturer shall not be liable for any damage or destruction of the product incurred as a result of misplacement incompetent installation and or undue operation and use of the product in contradiction herewith The manufacturer assumes no responsibility for any malfunction damage or destruction of the product caused by incompetent replacement of parts or due to the use of reproduction parts or components The manufacturer shall not be liable and responsible for any loss or damage incurred as a result of a natural disaster or any other unfavourable natural condition The manufacturer shall not be held liable for any damage of the product arising during the shipping thereof The manufacturer shall not make any warrant with regard to data loss or damage The manufacturer shall not be liable and responsible for any direct or indirect damage incurred as a result of a use of the product in contradiction herewith or a failure of the product due to a use in contradiction herewith All applicable legal regulations concerning the product s installation and use as well as provisions of technical standards on electric installations have to be
7. 10 Mechanical Installation 2 2 2 2 Mechanical Installation Mounting Type Overview Refer to the table below for a list of mounting types and necessary components 2N Helios IP Safety is preferably intended for surface mounting For recessed mounting it is necessary to order mounting frame or other accessories Surface mounting concrete and steel structures entry barrier columns etc N What You Need panama 1 s Me DANS p CO an Just your 2N Helios IP Safety unit LSS o a E BE M Recessed mounting classic bricks What You Need Frame 9152000 A precisely cut hole or optionally the brick flush mounting box Part No 9151001 Recessed mounting thermally insulated wall What You Need Frame 9152000 Longer screws depending on the thermal insulation thickness 11 Mechanical Installation 2 2 Recessed mounting hollow bricks What You Need Frame 9152000 Brick flush mounting box Part No 9151001 Flush mounting plasterboard wall What You Need Frame 9152000 Plasterboard flush mounting box Part No 9151002 Caution The warranty does not apply to the product defects and failures arisen as a result of improper mounting in contradiction herewith The manufacturer is neither liable for damages caused by theft within an area that is accessible after the attached electric lock is switched The product is not designed as a burglar protection device e
8. 2N Helios IP Safety Installation Manual Version 1 1 0 www 2n cz The 2N TELEKOMUNIKACE a s joint stock company is a Czech manufacturer and supplier of telecommunications eguipment A A A A Dd 6 Y v v v v The product family developed by 2N TELEKOMUNIKACE a s includes intercoms GSM and UMTS products private branch exchanges PBXs and M2M solution 2N TELEKOMUNIKACE a s has been ranked among the Czech top companies for years and represents a symbol of prosperity in the field of IP intercoms Furthermore the company dedicates significant attention to operator solutions as well as to effectively providing support for our distribution network and customer service At present we export our products into over 120 countries worldwide and have exclusive distributors on all continents 2N is a registered trademark of 2N TELEKOMUNIKACE a s Any product and or other names mentioned herein are registered trademarks and or trademarks or brands protected by law ss 2N TELEKOMUNIKACE administers the FAQ database to help you quickly find information and to answer your questions about 2N products and services On fag 2n cz you can find information regarding products adjustment and instructions for optimum use and procedures What to do if C Declaration of Conformity 2N TELEKOMUNIKACE a s hereby declares that the 2N Helios IP Safety product complies with all basic reguirements and other relevant pro
9. Configuration m Control E Maintenance 23 2N Helios IP Safety Configuration 3 1 3 1 2N Helios IP Safety Configuration Use a PC equipped with any web browser to configure 2N Helios IP Safety m Launch your web browser Internet Explorer Firefox etc m Enter the IP address of your intercom http 192 168 1 100 e g m Log in using the Admin user name and 2n password You have to know the IP address of your device to log in to the integrated web server By default 2N Helios IP Safety is switched into the dynamic IP address mode i e it obtains the IP address automatically if a properly set DHCP server is available in your LAN If no such DHCP server is available you can operate 2N Helios IP Safety in the static IP address mode Refer to the 2N Helios IP Configuration Manual for configuration details If your device remains inaccessible you have forgotten the IP address or the LAN configuration has changed for example change the LAN settings using the buttons on the device Switching between Static and Dynamic IP Address m Connect 2N Helios IP Safety to the power supply or disconnect and reconnect it if already connected Wait for the first acoustic signal Press button 1 15 times The acoustic signal indicates mode switching Wait until the device is restarted automatically Note The 15 times 1 sequence must be entered within 30 seconds after the first sound signal for security reasons
10. The inter digit delay may be 2s at most The static IP address mode will be switched into the dynamic IP address mode and vice versa upon restart 24 Maintenance 3 2 3 2 Maintenance Cleaning If used frequently 2N Helios IP Safety gets dirty To clean it use a piece of soft cloth moistened with clean water We recommend you to obey the following principles while cleaning m Never use aggressive detergents such as abrasives or strong disinfectants m Use suitable cleaning agents for glass lens cleaning cleaners for glasses optic devices screens etc m Alcohol based cleaners may be applied Clean the device in dry weather in order to make waste water evaporate quickly m The 2N Helios IP Safety models of Part Nos 9151101W and 9151101CW may be cleaned with WAP high pressure washers Future Tag Replacement Programming Changes For necessary steps refer to the preceding subsections Keep the following for future changes E This manual m Unused transparent foil strips for button tags Always use the product for the purpose it was designed and manufactured for in compliance herewith The manufacturer reserves the right to modify the product in order to improve its qualities 2N Helios IP Safety contains no environmentally harmful components When the product s service life is exhausted and you would like to dispose of it please do so in accordance with applicable legal regulations 25
11. ction we introduce the 2N Helios IP Safety product outline its application options and highlight the advantages following from its use Here is what you can find in this section Product Description Upgrade 2N Helios IP Safety Components and Associated Products Terms and Symbols 1 1 Product Description 1 1 Product Description Basic Features 2N Helios IP Safety is a highly resistant and reliable IP door access intercom provided with a lot of useful above standard functions Supporting the SIP standard and being compatible with the leading IP PBX and telephone suppliers 2N Helios IP Safety can make use of all VoIP services 2N Helios IP Safety can work as a standard Or emergency door access intercom for buildings entrances to premises or garages manufacturing halls highways and so on 2N Helios IP Safety is equipped with two very sensitive microphones and an up to 10W loudspeaker Thanks to an integrated acoustic echo cancelling AEC system the product provides mutual audibility even of persons talking at the same time under normal conditions 2N Helios IP Safety can be on request equipped with a colour wide angle camera which displays the calling person on the called party s video telephone or PC monitor 2N Helios IP Safety can be provided with 1 or on request 2 pre programmed buttons You can set up to three telephone numbers and time profiles for each of the buttons to increase the accessibil
12. ember that thermally insulated walls show less strength than classic brick walls 16 Mechanical Installation 2 2 Flush Mounting Hollow Bricks Suppose you intend to install your 2N Helios IP Safety unit into a wall made of hollow bricks Note that the external side of the bricks gets damaged by cutting and the dowels cannot practically be fixed into the thin internal part of the bricks Therefore use the brick flush mounting box and follow the instructions included therein Flush Mounting Plasterboard Use the plasterboard flush mounting box and follow the instructions included therein 17 Mechanical Installation 2 2 Use of Cable Bushings The cable bushings included in the 2N Helios IP Safety delivery are designed for the following cables Big bushing for two cables of the diameter of 5 6 mm UTP cable or upon insert replacement for one thick cable tube of the diameter of up to 14 mm Small bushing for one cable of the diameter of 5 8 mm Tip m Even a LAN cable including the RJ 45 connector can go through the big bushing See below for instructions How to Pull a RJ 45 Terminated Cable through a Bushing 1 Unscrew the big bushing nut completely 2 Remove the sealing including the cover from the bushing Cut either of the components as shown in the figures 3 Put the bushing nut on the cable and insert the sealing m 4 Replace the cover onto the sealing
13. h server RTSP server for video streaming SMTP client for e mail sending TFTP client for automatic configuration and firmware update 1 1 Upgrade 1 2 1 2 Upgrade The manufacturer reserves the right to modify the product in order to improve its qualities Version Changes 2N Helios IP Safety Components and Associated Products 1 3 1 3 2N Helios IP Safety Components and Associated Products Basic Units 9152101 1 button 9152101W 1 button 10W loudspeaker IP69 2N Helios IP Safety is designed for outdoor applications and requires no additional roof W including Part Nos are intended for WAP pressure cleaning and extremely noisy environments such as highways etc 2N Helios IP Safety units can wall mounted without requiring any additional accessories Use the appropriate mounting box see below for plasterboard and flush mounting 2N Helios IP Safety Components and Associated Products 1 3 Mounting Accessories 9152000 9151001 9151002 Mounting frame Brick flush mounting box Plasterboard flush mounting box orange Stainless steel Aluminum GSM UMTS Connection Accessories 505004 505214 505612 2N VoiceBlue Lite 2N VoiceBlue Enterprise 2N UMTS Office Route 2N Helios IP Safety Components and Associated Products 1 3 VoIP Connection Accessories 91378100 91378300 91378350 PoE injector Grandstream VoIP telephone Grandstream VoIP video telephone Electric Locks
14. her The system is equipped with the Auto MDIX function and so both the straight and crossed cable versions can be used External Power Supply Connection 2N Helios IP Safety can be fed either from an external 12V 1A DC power supply or from the LAN equipped with the PoE 802 3af supporting network elements External Power Supply An external 12V power supply is connected to terminal block X19 Use a 12V 15 DC power source dimensioned to current intake of 1A at least Part No 91341481E to ensure a reliable function of your device PoE Supply 2N Helios IP Safety is compatible with the PoE 802 3af Class 0 12 95W technology and can be supplied directly from the LAN via compatible network elements If your LAN in incompatible insert the PoE injector Part No 91758100E between 2N Helios IP Safety and the nearest network element 20 Electric Installation 2 3 Electric Lock Connection 2N Helios IP Safety is equipped with an electrically isolated relay switch with NO and NC contacts terminal block X17 and 12V 700mA switched output terminal block X18 to which a standard electric lock or another compatible electrical appliance can be connected Configuration Jumpers Configuration jumpers X6 are located in the right hand upper corner of the PCB and help reset the factory default values Factory Default Resetting 1 Disconnect the device from the power supply 2 Move the short circuit jumper on connector X6 i
15. hnan 10 Mechanical installaliOA a shave 11 Mounting Type OEI ti tore cust eich dela n st cams o A bo ozon 11 CommomMounthg Principles it eee ee oe ee 13 SUNCE MOUNINO aaraa o oe ene ree 14 Flush MOUNTING ClaSSIC BIICKS bidla at Hud pon k aiii 15 Flush Mounting Thermally Insulated Wall eee eee eee ener 16 Flush Mounting Hollow Bricks 14 bass d da 17 Flush Mounting Plasterboard 0 0200000000000 000 nr nehne Annan nn 17 Js eof Cable BUSHINGS asses a odhad a leo ds 18 Electric IAStala toi 19 POB AN ea OVO arado La bo oa 19 Gontiqutation JUMPE S canas ica iodo ieee egies 21 Mounting Comple lgi serrare alaridos 22 Function and USO Zo 3 1 3 2 2N Helios IP Safety Configuration c cscsesssssssssessscssesessssssevesssssceversseeseveveseneevareens 24 A AAA O a 25 A A 25 Future Tag Replacement Programming Changes eee 25 4 Technical Parameters s c seen 27 9 4 1 Technical Parameters iaa 28 Supplementary Information s 2s2e 31 5 1 Directives Laws and Regulations lt lt s lt rrrr sserrrxesea00 nese anna aaa n en nh 32 5 2 KFoubleshootNO susu usm s Ea AA A 33 5 3 General Instructions and Cautions sceree eee aaa aaa AKASA EAAS NON KA 34 Electric Waste and Used Battery Pack Handling 2 eee een 35 Product Overview In this se
16. it as a reserve Insert the plugs in the unused bushings and tighten the bushing nuts carefully 6 Do not complete mounting until you have finished electrical installation refer to Mounting Completion Where cables lead along the surface use the bushings included in the delivery 14 Mechanical Installation 2 2 Flush Mounting Classic Bricks If you use the brick flush mounting box follow the instructions included in the box If you do not use the mounting box follow the instructions below 1 Make a hole using the template Suppose that all the required cables have been carried into the hole 2 Unpack the frame put the intercom inside and place the set onto the hole to make sure that the hole is deep enough y U and the uneven edge is perfectly covered with the frame 3 Push or hammer the enclosed dowels into the drilled holes RAMAN 2M E Use some suitable building adhesive if the dowels are too loose 4 Remove the front panel from the intercom Remove bushings 5 Select the holes for cable supply Insert the blanks into the other holes Apply the cable bushings or a suitable sealant to prevent penetration of insects or water You can also insert the small bushing in the intercom bottom hole E c SSI DON 6 Put the frame on the intercom 7 Place the intercom into the hole x oS Y while introducing the cables Leave some of the cables inside the unit as a reserve and the
17. ity of the called party 2N Helios IP Safety is equipped with an electric lock switch You can control the switch using a numerical keypad or during a call using any telephone set An additional switch module can be installed if necessary A wide range of settings allow for a variety of applications 2N Helios IP Safety is very easy to install All you have to do is connect the system into your LAN via a network cable and feed it from a 12V power supply or your PoE Supporting LAN Configure 2N Helios IP Safety using your PC via any web browser Use the 2N Helios IP Manager to manage extensive 2N Helios IP Safety systems easily and quickly Product Description Advantages of Use Uncompromising AntiVandal design High covering level up to class IP69 Variable mounting options brick plasterboard flush mounting surface mounting Sensitive microphone and powerful loudspeaker Bidirectional communication acoustic echo cancelling Integrated colour camera with wide angle lens on reguest Integrated electronic lock switches with wide setting options Optional integrated RFID card reader module LAN PoE or external 12V power supply Configuration via web interface or dedicated PC application SIP 2 0 support Up to 999 telephone directory positions Up to 20 user time profiles Video codecs H 263 H 264 MPEG 4 JPEG Audio codecs G 711 G 729 HTTP server for configuration SNTP client for time synchronisation wit
18. nt and of the Council of 18 December 2006 concerning the Registration Evaluation Authorisation and Restriction of Chemicals REACH establishing a European Chemicals Agency amending Directive 1999 45 EC and repealing Council Regulation EEC No 793 93 and Commission Regulation EC No 1488 94 as well as Council Directive 76 769 EEC and Commission Directives 91 155 EEC 93 67 EEC 93 105 EC and 2000 21 EC E Directive 2002 96 EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment E Commission Regulation EC No 1275 2008 of 17 December 2008 implementing Directive 2005 32 EC of the European Parliament and of the Council with regard to ecodesign reguirements for standby and off mode electric power consumption of electrical and electronic household and office eguipment 32 5 2 Troubleshooting se For tips concerning solutions of other potential problems see fag 2n cz 33 General Instructions and Cautions 5 3 5 3 General Instructions and Cautions Please read this User Manual carefully before using the product Follow all instructions and recommendations included herein Any use of the product that is in contradiction with the instructions provided herein may result in malfunction damage or destruction of the product The manufacturer shall not be liable and responsible for any damage incurred as a result of a use of the product other than that included herein namely
19. nto the Default setup position Reconnect the power supply and wait for a start signalling sound 4 Disconnect the device from the power supply Move the short circuit jumper on connector X6 into the Normal operation position 6 Reconnect the power supply The device will be reset to factory default Default Connector X6 operation setup Table 2 1 Configuration Jumpers X6 21 Electric Installation 2 3 Mounting Completion 1 Having connected all the wires make sure that the bushings if used are tightened properly and the RJ 45 connector is inserted in the PCB connector 2 Connect the pushbutton cable to X5 and place the front cover carefully Make sure that the connector is inserted correctly and the wires inside the device leave enough space for the board if you are installing a four button board Tighten the four screws thoroughly with the wrench enclosed Torx 20 to make the panel fit tightly to the metal chassis Caution An incorrect mounting may compromise the intercom watertightness Water leakage may damage the electronic part of the system Stainless steel screws are used for the 2N Helios IP Safety assembly Other screws than stainless steel ones corrode soon and may aesthetically deteriorate the surrounding environment 22 Function and Use In this section we describe the basic and extending functions of the 2N Helios IP Safety product Here is what you can find in this section m
20. obeyed The manufacturer shall not be liable and responsible for damage or destruction of the product or damage incurred by the consumer in case the product is used and handled contrary to the said regulations and provisions The consumer shall at its own expense obtain software protection of the product The manufacturer shall not be held liable and responsible for any damage incurred as a result of the use of deficient or substandard security software The consumer shall without delay change the access password for the product after installation The manufacturer shall not be held liable or responsible for any damage incurred by the consumer in connection with the use of the original password The manufacturer also assumes no responsibility for additional costs incurred by the consumer as a result of making calls using a line with an increased tariff 34 General Instructions and Cautions 5 3 Electric Waste and Used Battery Pack Handling A Do not place used electric devices and battery packs into municipal waste containers An undue disposal thereof might impair the environment Deliver your expired electric appliances and battery packs removed from them to dedicated dumpsites or containers or give them back to the dealer or manufacturer for environmental friendly disposal The dealer or manufacturer shall take the product back free of charge and without reguiring another purchase Make sure that the devices to be disposed of are c
21. omplete Do not throw battery packs into fire Battery packs may not be taken into parts or shirt circuited either 35 2N TELEKOMUNIKACE a s Mod ansk 621 143 01 Prague 4 Czech Republic Tel 420 261 301 500 Fax 420 261 301 599 E mail sales 2n cz Web www 2n cz DR1788 v1 1
22. rest under the intercom bottom 8 Insert the enclosed screws in the lateral mounting holes making sure they have penetrated into the dowels Tighten all the screws properly Tip The screw tightening sequence may affect the intercom position 9 You can seal the frame wall gap with a silicone or another sealant to avoid wall dampening as a result of water leakage This additional sealing is unnecessary for the intercom function 10 Do not complete mounting until you have finished electrical installation refer to Mounting Completion 15 Mechanical Installation 2 2 Flush Mounting Thermally Insulated Wall Cut out the thermal insulation layer using the template the same as for classic brick wall Caution The hole depth depends on the insulation layer thickness If the insulation layer is rather thick you may need longer screws If there are hollow bricks under the insulation make sure that your screws pass through the whole dowel 50 mm and fix the dowel reliably Make sure that the dowel holes have the required diameter If the diameter is too large the dowels may get loose Use some suitable building adhesive to keep the dowels in place Make sure that the hole depth is sufficient too The dowel length is 50 mm and the screw length is 80 mm Suppose that all the required cables have been carried into the drilled hole Now follow the instructions applicable for classic brick flush mounting However rem
23. visions of the 1999 5 EC directive For the full wording of the Declaration of Conformity see the CD ROM enclosed and at www 2n cz genie 150 9001 lt C gt gt BUREAU VERITAS i x Certification 7828 2N TELEKOMUNIKACE company is the owner of the ISO 9001 2008 certificate All development production and distribution processes of the company are managed by this Standard and guarantee high quality technical level and professional aspect of all our products Contents Product OVI VICW cceccccecccceccncsccncsccscsncscencscencsnescsnesenesces 1 1 1 1 2 1 3 1 4 Product Descrip nicas 2 a ee 2 Advantage s or US Eissii nono poli Poly 3 A ia a G a a a e ia 4 2N Helios IP Safety Components and Associated Products sscsssesssssesesseesees 5 Base MTS aaa aN 5 Mounting Accessories cccsccccccceeeeecceeeeeecaeeeeeesaeseeesaaeeesseeeeeessaeeeessaueeessaeeeeesageeeesseeeeeeas 6 GSM UMTS Connection Accessories ccccooccncccoccnncccnnnncoconcnnononcnnnnonnnnnnnonnnnononennnnoncnnnnnos 6 VoIP Connection ACCESSOMIES eiii dr dani nents eee Sa d osou dete te b t a Mea 7 Plec LOCK iets sae sete EH ROP NE O T O E senesced 7 RJM ACC Co OS acc 7 Terms ANG SYMONS ici iS 8 SIM Si oie Sate creek eal dee ie lala nl e e aia 8 Description and Installation ooocconcconnnoncnonicoanonaronar Y 2 1 2 2 2 3 Before YOU Start uzce due io tantas 10 Product Completeness Check 0000000000000 nh
24. xcept when used in combination with a standard lock which has the security function When the proper mounting instructions are not met water might get in and destroy the electronics It is because the intercom circuits are under continuous voltage and water infiltration causes an electro chemical reaction The manufacturer s warranty shall be void for products damaged in this way 12 Mechanical Installation 2 2 Common Mounting Principles Caution Make sure that the dowel holes have the reguired diameter If the diameter is too large the dowels may get loose Use some suitable building adhesive to keep the dowels in place Make sure that the hole depth is sufficient too The dowel length is 50 mm and the screw length is 80 mm Remember that dowels of poor quality may easily get loose and fall out of the wall Stainless steel screws are used for the 2N Helios IP Safety assembly Other screws than stainless steel ones corrode soon and may aesthetically deteriorate the surrounding environment Having removed the front panel make sure that no dirt gets inside the product especially onto the sealing surface and microphone sound guides The microphone covers are normally loose after the front panel is removed The screw is only used as a fall out protection during installation 13 Mechanical Installation 2 2 Surface Mounting Wall surface mounting is used where flush mounting is inapplicable in concrete

Installation

Contents

Download Pdf Manuals

Related Search

Related Contents