MANUAL Battery protection
Contents
1. the battery is connected to the output with protection e Off the battery is disconnected from the output 3 4 Output connector The battery protection board has one output This output must be connected to the device e g LED fixtures 1 a Note Watch out for polarity Battery protection p 7 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com 3 5 Fuses board There are three fuses on board to protect every battery input Only replace the fuse with the same type and current installed in the battery protection board Battery protection p 8 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com 4 Service and maintenance 4 1 Safety precautions Read carefully the safety information in this manual Lock out the power on the entire system and allow all electronic devices to discharge and cool down before executing any service or maintenance 4 2 Cleaning Battery protection itself Extensive dirt and particle build up degrades performance and may cause overheating This can result in damaged board and power supply s Damage by inadequate cleaning or maintenance is not covered by the product warranty Never use solvents to clean the outer housing of the card Never use water or wet cloth Enclosure in which the board is integrated Best is to use compressed air to remove2. condition of the power supply network Inadequate packaging of the product when returning it under the RMA procedure Accidents or disasters or any cause beyond the control of Lux Lumen including but not limited to lightning water fire public disturbances improper ventilation and acts of god Others It is the responsibility of the customer to backup and save any software files and programs before repair and to restore the same after such repair This warranty does not affect the consumer s statutory rights under applicable national legislation in force nor the consumer s rights against the retailer arising from the sales purchase contract In the absence of applicable national legislation this warranty will be the consumer s sole and exclusive remedy and Lux Lumen cannot be liable for any incidental or consequential damages for breach of any express or implied warranty of this product For full details of the warranty offered on this product please contact Lux Lumen s service center p 14 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com 7 2 RMA procedure To send material back to Lux Lumen you need a RMA Return Material Authorization document that you will receive from Lux Lumen Without the RMA document we cannot accept the material The procedure to obtain a RMA Step 1 Customer contacts Lux Lumen about warranty defects if material h
3. dust or soft cloth to remove the dust in the cabinet When using compressed air care must be taken not to damage the fans in the enclosure Never use solvents to clean the outer housing of the enclosure 4 3 Monitoring Three LED s are located at the side of the battery protection board Battery protection p 9 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Battery protection The LED s indicate the status of the board like shown here below Name LED Over Good voltage Status led ON The voltage of Normal the battery 16 operation to high Status led lt N A N A LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Low voltage The voltage of the battery is to low N A p 10 16 Battery protection Troubleshooting Indication Status Problem of led Low voltage On The voltage of the battery is to low Overvoltage On The voltage of the battery is to high No output N A No battery voltage connected No output N A Position of the voltage switch No output N A Fuses broken voltage LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Action Charge the battery Turn the switch to the charge position Check the connected battery Wrong voltage or the board is configured for
4. Battery protection 10060 Battery protection CONTENT 1 PICTURE 1 AAN AARUN REIP SSRERSRE 3 1 1 GENERAL a 3 1 2 TOP Ice A UC UN Ann DID M LM CRI DU LIE UE 3 2 MECHANICAL 65 4 ELECTRICAL 65 5 GENERAL bd D oc ao RE a coe gta v CD D a 5 3 2 INPUT VOLTAGE RENS teas dion TRY XY 5 3 3 INPUT CONNECTORS seisisseses xaxa Vue TX XR 6 3 4 OUTPUT CONNECTOR i cn a ecc ce a c c D CX C SO D e aie 7 3 5 FU SES ON BOARD cR NA 8 4 SERVICE AND MAINTENANCE 9 4 1 SAFETY 9 4 2 CLEANING a tet c d d aa d c C e c d CA a d a C t 9 4 3 MONITORING Clem TE e ea eru 9 5 5 11 6 5 rancid RENE 12 6 1 EUEC
5. TRICAL EY OT eee Red edat 12 6 2 ENVIRONMENTAL i seris xa ex ict RY REX a ir x care se RYE TRY RING 12 7 WARRANTY p oua uiua SR NOEDRRRNREEIRRRREEERDRARNAEESRRRAE 13 7 1 APPLICATION OF 4 aa aaa aa aaa n 13 7 2 PROGED RE 554 eur ext vias ora e t e da a Ra 15 8 USED LIST OF 65 16 p 2 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Picture 1 1 General 1 2 Top Battery protection p 3 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Battery protection Mechanical specifications Dimensions 72 x 77 4 mm Max height of electronics 28 5 mm Weight 69 5 gr LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 432 3 293 35 50 32 3 293 35 44 www lux lumen com p 4 16 H Electrical specifications 3 1 General The battery protection board is used to connect batteries to a ledstrip Features e The board protects the battery by the use of fuses e The board avoids using the battery at too low voltages e The board allows easy switching between charging the battery turning the device on and off 3 2 Input voltage The battery protectio
6. another voltage Connect the right battery to the battery input Check the position of the switch Replace the fuses with the same voltage and current p 11 16 6 Specifications 6 1 Electrical Inputs Three battery inputs Max 4 A for every battery input Inputs on Cage clamp Three position switch input Battery charger input Status LED s for low voltage or overvoltage Separated fuse for every battery input Output e 1 output Output on Cage clamp for easy connection 6 2 Environmental IP rating IP 20 Humidity 30 to 95 Ta max 40 C 104 F Ta min 15 C 5 F Battery protection p 12 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Battery protection Warranty 7 1 Application of warranty Warranty period Warranty service is valid for one year from the date of purchase by the consumer as evidenced by invoice date given out by your point of sale Warranty service Service under warranty can only be done by Lux Lumen Co rdinaties Lux Lumen Kernenergiestraat 53 A 2610 Wilrijk Belgium Any cost of secure transportation of the product to and from Lux Lumen service department will be borne by the customer Limitations Lux Lumen will not warrant the following Periodic check ups maintenance and repair or replacement of parts due to normal wear and tear Consumables e Any software Defec
7. as to be returned Step 2 Lux Lumen sends the customer a filled out RMA document using a unique RMA number Step 3 Customer sends material include a copy of the RMA document with the material Step 4 Lux Lumen evaluates the problem and informs the client if repair is done under warranty or makes an offer to the client for repair Step 5 The procedure related to lux lumen quality procedures according ISO 9001 is started up Battery protection p 15 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Used list of abbreviations PCB printed circuit board e DC Direct current DIN rail rail used in electrical installation according to Deutsche Industry Norm specifications Battery protection p 16 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com
8. n board can work at different voltages Specify the desired output voltage when ordering the battery protection board The hardware and the software of the board will be configured on the desired battery voltage Typical output voltages 7 2 V 9 6 V 12V Nominal Voltage Voltage Voltage Type of Number voltage off V battery of cells 7 2 V 7 2 6 8 5 NiMh 6 9 6 V 9 6 8 11 6 NiMh 8 12V 12 10 14 Pb 6 Note Use a charger adapted to the battery type Battery protection p 5 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com 3 3 Input connectors The battery protection board has three different inputs Battery input There are three battery inputs on the board Multiple battery units can be used on the board The inputs are parallel connected on the board Note Watch out for polarity Charger The right charger must be connected to the charger input of the board A battery charger must be used that corresponds to the specifications of the batteries Battery protection p 6 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 432 3 293 35 50 32 3 293 35 44 www lux lumen com Switch A three position switch must be connected to the battery protection board The switch can change the state of the output There are three possible positions e Charging the battery packs will be charged no output e On
9. ts caused by modifications carried out without Lux Lumen s approval e Damage resulting from the fact that a product is not conforming to country specific standards or specifications in another country that the country of purchase Costs incurred by Lux Lumen s service center in making any adoptions or modifications of a product necessary for country specific technical or safety standards or specifications or any other cost to adjust the product as a result of any specifications which have changed since the delivery of the product p 13 16 LUX LUMEN Kernenergiestraat 53A 2610 WILRIJK BELGIUM T 32 3 293 35 50 32 3 293 35 44 www lux lumen com Battery protection Warranty service is excluded if damage or defects have been caused by Improper use extensive use handling or operation of the product as referred to in the user manual or operator manual and or relevant user documents including without limitation incorrect storage dropping excessive shocks corrosions dirt water or sand damage if the product is not rated to be used in severe conditions indicated by its IP and IK degree mentioned in the product specifications in this manual Repairs modifications or cleaning carried out by a non Lux Lumen service centre Use of spare parts software or consumables which are not compatible with the product Connecting the product to equipment not intended to be used with this product Defects caused by improper
Download Pdf Manuals
Related Search