Long Range Infrared Housing Instruction Manual
Contents
1. the spacer from the accessory pack and stick it right by the outlet Fig A or 2 use the three glands cover and let the power cable and video cable pass through the hole of glands cover Fig B Fig A Fig B INSTALLATION 3 4 Open the side cover and you can see the housing inner part There are two installation types Inner Part Definition power connector board only IR LED driver board in AC90 260V housing Hb Power 2B Adpator only in AC90 260V housing Heater board Camera position mal Hn T le eater li H id PTC INSTALLATION 3 4 1 Inner Part Installation MESSOA SCB261 SCB265PRO SCB282PRO 3 4 1 1 Install the camera to the camera position as illustrated 3 4 1 2 Enable the day night sync funciton connect the day night sync cable to P203 and the to the BW GND port pin side BW brown line GND black line of the camera back SCBZB5FRO SCB282PRO Camera Back IR LED driver board BROWN BLACK day night sync cable INSTALLATION 3 4 1 3 Enable the video sync funciton connect the video sync cable to P202 and to the to the video output port of the camera se al g x O Ello T OGA U f N SCB265PRO SCB282PRO M H Cy Camera Back IR LED driver board a _ L video sync cable INSTALLATION 3 4 1 4 Be sure to switch the S203 mode on the IR LED driver board to the Middle position2. Long Range Infrared Housing Instruction Manual ZEIM 4000224G A 5 070 CONTENTS m SAFETY INFORMATION nu 1 m PART DESCRIPTION amp DIMENSION sra aia 3 MINS BHO rancia 4 MSPECIFICADO Nc pitan 15 Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use SAFETY INFORMATION Safety Information 1 co Read this Instruction Manual Before using the product please carefully read through the safety information and operation instructions Keep this Instruction Manual Safely store the Instruction Manual for future reference Follow instructions When operating the unit please follow instructions on the Instruction Manual Cleaning Before cleaning the unit please first unplug the power Peripheral accessories Do not place the unit on an unstable cart tripod or on a tabletop as personal injury and damage to the unit may occur due to a fall Please use officially certified support frames and accessories included with the product Follow the instructions in this Instruction Manual during installation to ensure the quality and maintain safety Power Please follow the labeled specifications on the unit and supply with the correct power If unsure of the actual power requirements please contact the distributor and do not connect the power at will Power cable The power cable must be properly secured as improper connections may
3. P201 i gm P203 Orm B Middle Down 6 g INSTALLATION 3 4 2 Inner Part Installation MESSOA NIC836i and Other Brands 3 4 2 1 Install the camera to the camera position as illustrated 3 4 2 2 Enable the day night sync funciton connect the day night sync cable to P203 and the to the AL GND port pin side AL I brown line GND black line of the camera back Nl 836 Camera Back IR LED driver board BROWN BLACK day night sync cable INSTALLATION 3 4 2 3 Be sure to switch the S203 mode on the IR LED driver board to the Up position P201 a ee EB P203 ju O 3 p OS SB Se Up 88 middie z B Down O INSTALLATION 3 5 Connect the power cable to the power port of the AC24V camera and to the A section L power N power as below Connect the outside AC24V power supply to the section B L power N power P507 P502 Partial heater board Note For the AC90 260V housing type connect the power cable to the power port of the AC90 260V camera and to A section L power N power Connect the outside AC90 260V power supply to the section B L power N power Partial power connector board 12 INSTALLATION 3 6 Then close the side cover and use the provided screws to fix the housing on the bracket with hexagon screw driver 3 7 Loosen the pan and tilt adjustment screw of the bracket to modify the angle of the hou
4. cause a short circuit fire hazards or serious damage and hazards Lightning strike During prolonged inactivity please unplug the power cable and the video cable to avoid damage from lightning strike and power surges Foreign objects and fluids Please do not insert any objects into the unit or spill liquids to avoid short circuits 10 Warning High voltage circuitry contained within the unit Do not disassemble to avoid electric shock All maintenance operations must be handled by qualified maintenance staff SAFETY INFORMATION 11 Maintenance When the following occurs please first power off the unit and then perform maintenance by qualified maintenance staff a Damaged power cable or socket b Liquid spills or foreign objects in the unit c Inoperable unit when proper instructions are followed d Dropped unit or damaged shell e Other anomalies 12 Component replacement Replaced components by the maintenance staff must be official certified parts of identical specifications Using unauthorized components can cause fire hazards and electric shock damage 13 Safety inspection After the unit maintenance has been completed the maintenance staff must perform safety inspection to ensure proper operation The triangle symbol with lightning arrow indicates that ungrounded Hazardous Voltage exists within the unit The voltage level may cause personal electric shock hazards The triangle symb
5. ol with exclamation mark indicates that there are important operation and maintenance instructions in the Instruction Manual PART DESCRIPTION amp DIMENSION 1 Structure Illustration 1 TOP COVER 2 TEMPERED GLASS 3 BOTTOM COVER 4 BRACKET 5 TILT ADJUSTEMT SCREW 6 PAN ADJUSTEMT SCREW The figure above is the illustration of the housing which may be used with most of ICR real Day and Night cameras 2 Dimension and Accessory ACE j _ 366 ij LO Accessory Pack 1 Video sync cable 7 Spacer 2 Day night sync cable 8 2 Screws for tripod stand 3 Camera power cable 9 User manual 4 BNC connector 5 3 Glands 6 Hexagon screw driver INSTALLATION 3 How to install the camera and bracket 3 1 Take the bracket from the box and put the power cable and video cable through the bracket then fix the bracket to the wall Loose the screws of the bracket for easy assembly if necessary 3 2 Secondly take out the housing and open the side cover with hexagon screw driver N INSTALLATION 3 3 Put the power cable and video cable through the bottom of the housing and let them pass from the hole Attention Two solutions are available for waterproof 1 User can take out
6. sing and then tighten the screw INSTALLATION 3 8 Replace the side cover and tighten the screws A B SPECIFICATION R LED lt 210 x 70 x 90 mm 8 3 x 2 7 x 3 5 174 x 422 x 145 mm 6 9 x 16 6 x 5 7 30 C 50C 22 F 122 F 30 90 RH 40 C 60C 40 F 140 F Yes amd NOTE The specification is subject to change without notice Sn
Download Pdf Manuals
Related Search