2. The main window - NCT Ipari Elektronikai Kft.
Contents
1. Del Param button Deleting macro Select a G code which you want to delete and click on the Del Macro button 5 Special keys mentioned in this help Escape Windows key Menu key Box up and box down key Break key Arrows 28 Switch page Reset key We can start numeric keyboard mode by pressing the Fn and NumLk Del keys in the same time For Stop press Fn NumLk too In this mode only the keys with the green numbers works Only on the PC size is can be used While keeping pressed the Fn key the mouse cursor can be controlled by the arrows The speed is increased while pressing the arrows 6 Information s for system administrators We can install the mouse in two modes or with a Y cable attached to the FEW unit s PS 2 output in the command chest this method disadvantage is that the cable is to short this is not recommended or with an ordered a special cable from NCT witch is attended with an transmitter receiver unit 50 m is this cable maximum long The system s files or in the WINNT or in the WINDOWS directory are in the bd_kibocs subdirectory At the Fnc exe refreshing after the stopping the Fnc exe Alt F4 keys in this directory must be copied the new files This operation is executable only after consulting with NCT s specialists In the following paragraphs always bd_kibocs_mill folder will be mentioned Bd_kibocs_mill folder is used for milling version In the case of turning lathe use bd_2. or 01234 MY PROGRAM Or 1234 You can not copy during DNC mode Press STOP key to stop DNC program and press RESET key twice Next you can do the copy action Rewrite a file if the file has already existed then you can cancel the copy with Cancel button or rewrite with Rewrite button The All button will rewrite all of the files Copy a file during editing running If you want to copy a file which is editing on NC side then you have to finish the editing and change of the Program Edit view If the program is running then you have to stop it with STOP or RESET key Program memory full 25 Delete some files from the Program Folder on NC side The file transfer could be interrupted with Cancel button 3 4 Property sheet of G120 macros Trapezoid grooving G1 21 G1211 G121 1l Area I Outer Point 4 XS 50 Machining process P Roughing X Point 3 X M Point 4 Z V 47 076 a Corner typ W Corner R Point 3 Z U Point 4 R C Y Cut start X0 130 Point 3 R C R EndpointX J 96 Cut start Z0 End point Z K 44 076 Step amnt Q gt Start point X H Start point Z Point 1 X A Point 1 7B Point 1 R C C a ALAA Point 2 X D Point 2 7 E Point 2 R C E Alkalmaz You can select among edit boxes with the box up and box down buttons Other way to push Alt underline letter For example on the above picture the Alt Z will select the
3. Cut start Z0 edit box If an edit box is selected the software show s the definite size with red on the picture or a new picture appears which show s the parameter using You can move among the property windows with the property window button The window is closed by enter key and the NC command will be generated and inserted automatically to the command window For example if a G121 command was selected on the command window before the G121 window opening then the property window will be filled with the appropriate parameters The modified parameters will overwrite the G121 command Attention Always pay attention to all property windows and after the last window push enter 26 3 5 Tool function window The appropriate tool will be placed in the spindle and the tool compensation will be turned on Cc Tool Function T x Teol Function T Work Coordinate System Coordinate Dieta Work Coordinate System Coordinate Data eGA GS GS Gh GSB e G59 z GM eGo F G4 GS G56 GS7 GSB G59 F G90 G91 Plane Selection Cutting Feed Rate Inch Metric Conversion Plane Selection Cutting Feed Rate InchMetric Conversion Gi7 c Gi c Gi Go4 r G06 Go G1 GW G18 G19 r G G95 r G20 G21 Tool change 990 G54 Gi G17 G40 GA Gel Tool change G90 G54 G80 G18 G40 G95 G21 A Tl 2000 KOMMENT T101 KOMMENT By tool change mish GO X30 Y40 MI ME Tool number 0 99 T j G92 53000 Tool number T i amp G96 250 10mm
4. Launch the New Hardware hardware update wizard follow the steps of Follow the steps of in the wizard Steps in New Driver Wizard Choose the following Ts 2 3 4 5 Install form list or specific location Advanced Next Don t search will choose the driver to install Next Have Disk Browse Choose bd_kibocs_mill nctfewkb inf in the case of keyboard installation or bd_kibocs_mill nctfewmou in the case of mouse installation Open OK Next Continuous anyway The divers of NCT are not signed by Microsoft but are very well tested by NCT Finish Launch New Hardware Wizard Hardware Update Wizard PRONETS Launch Control Panel from the Start Menu Choose System Choose the Hardware tab Press Device Manager In the case of keyboard installation a Click on the keyboard node b You can find two sub node unknown device or NCT FEW Keyboard and PS 2 keyboard Right click on unknown device or NCT FEW Keyboard choose update driver In the case of mouse installation a Click on the mouse node b You can find two sub node unknown device or NctFewMou and PS 2 or USB mouse Right click on unknown device or NctFewMou choose update driver The wizard starts 30
5. PC file selection in the FEW window You can move inside the window with the box up and box down or the navigation keys You can choose a folder with the navigation keys and the files appears on the window The file commands are available with the menu key You can select a file with the SPACE key You can select more files in case you want to copy from PC to NC with navigation keys Shift key You can select all of the files with Ctrl A keys You can use the function of clipboard with Ctrl C Ctrl V Ctri X Del keys Look irr E Bd Kibocs d E Flbootremove E wWinloz boot_setup WinIO2 dll Ba Fric Sinio SI NCTLOGO WINO XO Simple_C_ Proj E Wino File name Files of type All Files Cancel 3 2 Command window You can select the text with navigation keys Shift key If you push the menu key then you can use the functions of edit menu Useful keys Alt F Enter the file menu Alt S Enter the edit menu 21 Alt N Enter the View menu Ctrl S Save Ctrl C Copy the selected file text to the clipboard Ctrl X Cut the selected file text to the clipboard Ctrl V Paste from the clipboard Del Delete the selected object 3 3 The FEW window Functions 3 3 1 Open a file from NC to command window F1 This function is enabled if one file and no more is selected on the NC side 3 3 2 Save from command window to NC F2 This function is enabled always If we are in the Program F
6. RoundEndbaill HO 1 32000 oO G90 G4 G80 G18 G40 G95 G21 Comment ee aes General turn GC4015 T101 ROMMEND GF 52000 GO X30 Z5 M3 M8 ils Next preparing tool number T G 30 Y40 M3 ME 43 250 Fl p Spindle rotation a TET Surface Speed pe ae ghest spindle speed enabled 5 Swite Spindle Speed 5 2500 es Spindle speed S 2000 C Switch On G96 Positioning Moving X Bo Moving Y Positioning Coolant management oe 4 s C Coolant on M7 Set up the tool length compensation G43 Coolant management Moving X C M3 Coolant on M8 Z position after toolchange 50 al atl Maving Z wl Coolant off M9 Coolant on M Address H means the comp cell iil Coolant ofi Mo cot 4 Defining user G code Start the editor program with c program files nct fnc se editoreditor exe 4 1 The main window aa Hi propran ird programi Er propran Open usema gt Defa birres E dii eann hami Himas Wie aed 2 re doing iby hand sien pou can sperd all ghi plus most of the bolong day ving a bsr bo do it bor poar 21 Select the macro file in combo box beside of the open button Select user macro then press the open button to read the contents of the user macro The G codes are in the textboxes under the macro the parameters are in textboxes under the param The actually image is on the left side of the bottom region of the window The help text displayed o
7. available from the measuring cycles submenu The F1 F2 F3 buttons provide the calibrating funtions to calibrate the stylus These functions and G codes are detailed on Probe cycles and Digitalizing book Back to the measuring cycles submenu with escape key from the calibrating submenu The measuring submenu F2 This submenu available from the measuring cycles submenu This code group inserts the commands of measuring touch probe functions into the edit box These functions and G codes are detailed on Probe cycles and Digitalizing book Back to the measuring cycles submenu with escape key from the measuring submenu User G code submenu F8 User G code This code group inserts the commands of the User G code functions into the edit box Back to the main menu with escape key from the User G code submenu 2 2 Lathe OAD RILL nct Foe File Edit View Maros G todes Help Prinhty Ooch iinard Ray Menu NOW Se Ure ene ta es eee 02001 DRILL G83 698 G90 G54 i i Tool Function he 4 a T101 t o o o O ee M3 S1000 Actual phrase t T it H me l P14 a 1 i it a Peck Drilling Cycle sb ii il LE pat f 1 a4 Canned Cycle Cancel fi a ie f M30 PEt PEti 0 Help image window p Bottom pos of hole X ho a PECK DRILLING CYCLE Help text window Boom pas of hole aa ETF t Fee RE a EE Fk aes Giscea7_xX_C_ Y _R_Q_E_F_L_ Bottom pos of hole Z 20 oega MRE F GO e
8. Back to the main menu with escape key from the single submenu The multiple submenu F4 Some multiple functions are available on the Multiple submenu because of the space The dialog windows of hole are detailed on Programmer s manual book If you press one of these buttons a popup dialog will be active except F1 button it is unattached from the state of Dialog submenu of the View menu Back to the main menu with escape key from the multiple submenu Thread submenu F5 het Mesa n Some thread functions are available on the Thread submenu because of the space The dialog windows of hole are detailed on Programmer s manual book If you press the F1 button a popup dialog will be active it is unattached from the state of Dialog submenu of the View menu Back to the main menu with escape button from the thread submenu The macro submenu F6 This buttons will open the dialog windows of G100 macros They are detailed on dialog If you press one of these buttons a popup dialog will be active it is unattached from the state of Dialog submenu of the View menu Back to the main menu with escape key from the macro submenu The hole submenu F7 Other Get Gee Cad Bod 84 243 eo C86 86 1 Ge GBE eo some hole functions are available on the Other submenu because of the space The dialog windows of hole are detailed on Programmer s manual book Back to the main menu with escape key from the hole subme
9. DiNog The operations of the cycle are window poses entnesnnntnnenteentn Operation 1 rapid traverse positioning in the selected plane Approach point B 20 Operation 2 NERE an eaat aiai Operation 3 rapid traverse movement to point R Cute in value Q 3 Operation 4 eee rs w 2 2 1 The buttons on the bottom It help s using the software without mouse like NCT controllers The buttons are reachable with F1 F2 F10 keys The buttons has two state enabled disabled If a button is disabled then Its picture has gray color and ineffective 14 The actual phrase is displayed in the edit window and it has always yellow background If this phrase starts with a G code which is displayed in the bottom keys also and there is no other G code in this phrase the corresponding editboxes of these parameters will be displayed otherwise this G code does not contain parameters Beside the editboxes is displayed the corresponding image in the image window area and help text in the help window area If the dialog window is changed then editbox will be changed automatically and conversely We can restrict this duplex write method to a simplex method but we can disable it too if it is necessary It available in the CodeWizard gt heading and Heading gt editor submenu 2 2 2 The main menu Multiple Thread ale Mhe pinde Toal The submenus of main menu are reachable with the F1 F2 F10 keys Back to the main menu wit
10. NCT FEW4 User s manual Instruction book 2006 Contents l 2 OG A o PATA EE A E E E EE E E E E E AO E E E E 3 Ll oOweron oOowero ww 3 ein id 4 Me MM eres acters E te pce pete es ves nc ee ge Sones eee eee 4 ZA The buttons on the DO TON se 4 VAA T E a ES N E E E E E ene EE S 5 2a Eae ee E E ee eee 14 22l The buttons on the DOM OM ee 14 222 THEa n A 1 hc Sacco cs ease A E E 15 WO 21 mle Lite 21 JU 21 GP mmm Bo era oi chk le 1117 lt 6 ee E ne mn ne ence ee ee ee eee ee ees 22 3 3 1 Open a file from NC to command Window F1 ccccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 2A LR PA Save trom command Window to NC F2 ecenisrorieririai iirinn anana EEE AAA ERA AAR 22 3 3 3 Copy from NC to floppy hard disk network 3 7 22 3 3 4 Copy from floppy hard disk network to NC 4 22 5 2 0 File selection to DNC OU 22 3 3 6 De eC ClO MOT FC TINE CS CI axiscsias se onresntudise tales E sec asua cies ndea ie ena seies need ocean es eae eee 23 Doel Selecon TO 23 Eee 23 3 3 9 EL 23 PA OU TE oases peer E E E AA E TA 23 TL MT oncptatciensaswnsscaossvcmaneceseret A E E E A N 23 Po P S E E T A A 24 Joda Selecion of ING Ha 24 3 3 14 Error messages of FEW Wid OW vecenenscesaedonssnatedsnncdecenssdasuaderssnsseedsaseaterstesdasasussaderstedeedsaosadeisdeuses 24 34 Property sheet of G20 Macros a gai cncstctwacanarastsanopncnacinnronswnnsisleadioniiehosaits voup
11. The G25 G26 submenu F3 This submenu available from the spindle submenu This code group inserts the commands of the G25 G26 spindle speed fluctuation detection functions into the edit box These functions are detailed on Programmer s manual book Back to the spindle submenu with escape key from the G25 G26 submenu The G43 G43 submenu F5 This submenu available from the spindle submenu This code group inserts the commands of the G43 G44 tool lenght compensation functions into the edit box The F3 key only insert a G49 code tool length compensation cancel from the cursor position These functions are detailed on Programmer s manual book Back to the spindle submenu with escape key from the G43 G44 submenu The G41 G42 submenu F6 This submenu available from the spindle submenu The F1 F2 F3 buttons insert a tool radius compensation code into the edit window F1 means radius compensation cancel F2 means radius compensation left F3 means radius compensation right These functions are detailed on Programmer s manual book Back to the spindle submenu with escape key from the G41 G42 submenu Measure cycles submenu F7 Calibration Measuring These functions provide measuring and calibrating functions These functions and G codes are detailed on Probe cycles and Digitalizing book Back to the main menu with escape key from the measure cycles submenu The calibrating submenu F1 This submenu
12. This submenu available from the spindle submenu This code group inserts the commands of the G68 G69 coordinate system rotation functions into the edit box These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G68 G69 submenu The G50 G51 submenu F2 This submenu available from the spindle submenu This code group inserts the commands of the G50 G51 scaling functions into the edit box These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G50 G51 submenu The G50 1 G51 1 submenu F3 This submenu available from the spindle submenu This code group inserts the commands of the G50 1 G51 1 mirror image functions into the edit box These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G50 1 G51 1 submenu The spindle submenu F6 ia ml a C69 so Cr Ei 4a G44 GA TEHA Select a submenu with F1 F6 key These spindle functions are detailed on Programmer s manual book Back to the main menu with escape key from the spindle submenu The G96 G97 submenu F1 This submenu available from the spindle submenu This code group inserts the commands of the G96 G97 constant surface speed functions into the edit box These functions are detailed on Programmer s manual book Back to the spindle submenu with escape key from the G96 G97 submenu
13. angle submenu The circle submenu F2 SS le B C Rough Bottom fin Side fin Chanmfer Geometry This code group inserts the commands of the circle pocket machining functions into the edit box Back to the pocket submenu with escape key from the circle submenu The track submenu F3 i i Geometry Drill Rough Side hin Bottom fin This code group inserts the commands of the track pocket machining functions into the edit box Back to the pocket submenu with escape key from the track submenu The groove submenu F4 E E Geometry Rough Bottom fin Side fin j Chanter This code group inserts the commands of the groove pocket machining functions into the edit box Back to the pocket submenu with escape key from the groove submenu The submenu of the Drilling cycles and the other G codes Driling cycles submenu F4 Select a submenu with F1 F10 key The drilling cycle functions are detailed on Programmer s manual book Back to the main submenu with escape key from the drilling cycles submenu Drilling cycles other functions submenu F1 Ton Fon On on n On He Ue he He yey he Hory jf OW Of Ol i Of esc Jj Of ceo as cw a7 awe G19 This submenu available from the drilling cycles submenu This code group inserts the commands of the other drilling cy
14. cle functions into the edit box Cycle modal call cancel plane selection etc These functions are detailed on Programmer s manual book Back to the drilling cycles submenu with escape key from the drilling cycles other functions submenu The G83 G83 3 submenu F4 This submenu available from the spindle submenu This code group inserts the commands of the G83 G83 3 drilling cycle functions into the edit box These functions are detailed on Programmer s manual book Back to the drilling cycles submenu with escape key from the G83 G83 3 submenu The G84 G84 3 submenu F5 This submenu available from the spindle submenu This code group inserts the commands of the G84 G84 3 drilling cycle functions into the edit box These functions are detailed on Programmer s manual book Back to the drilling cycles submenu with escape key from the G84 G84 3 submenu The G86 G76 submenu F7 This submenu available from the spindle submenu This code group inserts the commands of the G86 G76 drilling cycle functions into the edit box These functions are detailed on Programmer s manual book Back to the drilling cycles submenu with escape key from the G86 G76 submenu The other submenu F5 Select a submenu with F1 F3 key or a programming help function with F5 F8 buttons The contour wizard not available at the moment Back to the technology submenu with escape key from the other submenu The G68 G69 submenu F1
15. displayed in the popup dialog Back to the hole submenu with escape key from the G86 G86 1 submenu The other submenu F8 This spindle functions could be inserted with F1 F2 F4 buttons The dialog windows of spindle functions are detailed on Programmer s manual book The ContourWizard not available at the moment Back to the main menu with escape key from the other submenu The G68 G69 submenu F1 This submenu available from the other submenu This code group inserts the commands of the G68 G69 mirror image for double turret functions into the edit box These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G68 G69 submenu The G51 G50 submenu F2 This submenu available from the other submenu This code group inserts the commands of the G51 G50 scaling functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G51 G50 submenu The G51 1 G50 1 submenu F3 This code group inserts the commands of the G51 1 G50 1 mirroring functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back
16. e as F4 keys You can use FEW Floppy Ethernet Winchester functions with F4 key It is detailed on dialogs The print print prev and print setup buttons is similar to Windows print functions It is enabled if a printer is installed Back to the main menu with escape key The edit submenu F2 Paste Select All The buttons of edit submenu are similar to functions of Windows edit menu The undo button is enabled if happened any edit command The cut and copy buttons are enabled if text is selected The paste button is enabled if there are any text on the clipboard The select all button will select all of the text on the command window The selection of text is detailed on dialogs Back to the main menu with escape key The submenus of G400 macro Technology submenu F3 Face Hole Pat Step Hi This buttons will open the dialog windows of technology macros Back to the main menu with escape key Face submenu F1 This code group inserts the commands of the face machining functions into the edit box Back to the Technology submenu with escape key from the face submenu Hole pattern submenu F2 E EA S Points This code group inserts the commands of the hole pattern functions into the edit box Back to the Technology submenu with escape key from the hole pattern submenu Side submenu F3 This code group inserts the commands of the side machining functions into the edit bo
17. e started The Fnc DNC window gives information about the following the content of the DNC list the name of the file which is executed state of the execution percent C DNC List CANCProgram Demo WY 2 NCT 5 Executed file CANCProgram Demo VYW 2 NCT Estimated time left hour min sec 0 0 36 M Shutdown Yindows after DNC is finished We have an opportunity here to turn up that after DNC ended Windows let him stop it automatically Closes an application running on all of them at this time Listen up Without a rescue and Windows stops it 3 3 6 Selection of PC file s F6 This is a file open window The selected files appear on the PC side of FEW window The file name window show s the files 3 3 7 Selection of PC folder F7 You can select a folder with navigation keys and press Enter or Esc key to cancel 3 3 8 Delete F8 Deletes the selected file from the DNC list 3 3 9 Select all F9 Selects all files in the File name NC windows 3 3 10 Sort F10 Adds the selected file in the File name PC windows to the DNC list 3 3 11 Measure Measurement results generated by POPEN DPRINT etc commands can be saved by this button 1 Press the Measure button in the WinFEW window 2 Inthe popup dialog select the name and the location of the file to be created 23 3 Start your NC program which contains the POPEN DPRINT PCLOS etc commands like serial port communication 4 After PCLOS
18. ers are in other books 1 1 Power on Power off The PC unit which is an integral part of the control system is launched automatically The operation system of PC unit is Windows XP The DEAK software fnc exe which establish communication is automatically launched Before Power off you must shut down the Windows XP 1 Push Alt F on the main window of Deak Fnc exe software and choose Shut down on the list This is hard reset it will close all programs without save 2 Push the Windows button and choose Shut down on the list 3 Close the all active window with Alt F4 finally choose Shut down 4 In DNC window check in a pipe Windows Shut down option Attention On the Shut down window always choose shut down 2 The main window 2 1 Mill OD LE et Foe Fie Edi West Mate Grote Hels Pearly Codeoed each Menu MUM Edi Vm Tice View y 9602001 DRILL Loy c 5o G90 G54 Actual phrase O a e vee M3 51000 lo window G83 Z 12 5 R1 Q3 E1 P1 F100 L04 aye G400 X170 120 A180 B40 C50 D30 E80 aes P F40 H950 ISO J20 K35 G80 Point 1X 170 M30 Ho Fonit 1 Y p20 Poit 2 A 1180 HOLE PATTERN POINTS Pointze Dialog window 40 x E coodinate of the position of first hole Point 3 C En Help text window Point 3 D 30 Point AE ao y a P im lin 7 re inde Cut Copy Paste Select All Fira Repeat Replace 2 1 1 The buttons on the bottom It help s using the software witho
19. h escape key The file submenu F1 The new F1 button deletes the command window and a new program frame will appear The program number and name are editable The open save save as functions are similar to Windows functions You can open a file from floppy hard disk network with the open F2 button You can save the contents of command window with save F3 and save as F4 keys You can use FEW Floppy Ethernet Winchester functions with F4 key It is detailed on dialogs The print print prev and print setup buttons is similar to Windows print functions It is enabled if a printer is installed Back to the main menu with escape key The edit submenu F2 Undo Paste Select All The buttons of edit submenu are similar to functions of Windows edit menu The undo button is enabled if happened any edit command The cut and copy buttons are enabled if text is selected The paste button is enabled if there are any text on the clipboard The select all button will select all of the text on the command window The selection of text is detailed on editwindow Back to the main menu with escape key from the edit submenu Single submenu F3 Some single functions are available on the Single submenu because of the space The dialog windows of hole are detailed on Programmer s manual book If the Dialog submenu is enabled in the View menu the parameters are displayed in the popup dialog dialogs
20. have been executed the WinFEW window is closed 3 3 12 Exit lt lt lf no Communication command is under execution the program go back to the main window In other case the PC NC communication will be broken If you press it first then a communication is broken message is sent to the NC If this message can be sent successful then the communication will be broken by the PC You can use this function to handle communication errors If the NC is not able to receive this message above then the communication error will not solved In this case press the Exit button again This method can cause further errors in the NC but the error in the PC side will be solved 3 3 13 Selection of NC files Press Space key to selection WinFEW Eg NC PC File name NC Params Measur File name PC Log file DNC List w al XK LT PC file PC Folder Del in list Select All Sort in list NC gt gt ED ED gt gt NC 3 3 14 Error messages of FEW window 1 Syntax error Program syntax e the first character is 24 the second character is O next are four number program number the seventh character is next is the name of the program it is not necessary next character is the above string does not contain space character except program name the above string does not contain new line the program end is a character True False 01234 MY PROGRAM 01234 MY PROGRAM or 01234
21. kibocs_lathe folder 6 1 Reinstallation of Windows XP 1 Plug anormal PC keyboard into the PS 2 output of the FEW card and a mouse Y cable needed 2 Install Windows XP from the install CD 3 Copy bd_kibocs_mill folder to the C drive of the FEW card You can get this folder by email or CD 4 Install the NCT keyboard and the NCT mouse divers see below 5 Launch the boot_setup exe console application This program installs the WinlO library winio sys and winio dll which is used for dual port memory file transfer You can remove the Winio library by launching boot_remove exe if you need 6 Create shortcuts for Fnc exe bd_kibocs_mill Fnc exe Use and enjoy it 6 2 Installation of NCT Keyboard and mouse 1 Launch devkb bat in bd_kibocs_mill driver folder Windows XP signs that new hardware have been founded Wait some seconds The New Hardware Wizard starts If the wizard does not start follow the steps of Follow the steps of Windows XP signs that the keyboard driver is installed and ready for use Launch devkb bat in bd_kibocs_mill driver folder Windows XP signs that new hardware have been founded Wait some seconds The New Hardware Wizard starts If the wizard does not start follow the steps of 5 Follow the steps of 6 Windows XP signs that the mouse driver is installed and ready for use 29 Use and enjoy it 6 3 Driver update for NCT keyboard and mouse 1 2
22. menu available from the spindle submenu This code group inserts the commands of the G25 G26 spindle speed fluctuation detection functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the spindle menu with escape key from the G25 G26 submenu The G12 1 G13 1 submenu F8 12 1 G13 1 This submenu available from the spindle submenu This code group inserts the commands of the G12 1 G13 1 polar coordinate interpolation functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the spindle menu with escape key from the G12 1 G13 1 submenu The G51 2 G50 2 submenu F10 P oa P Q aa ul G512 G02 This submenu available from the spindle submenu This code group inserts the commands of the G51 2 G50 2 polygonal turning functions into the edit box If the Dialog submenu of the View menu 20 is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the spindle menu with escape key from the A G51 2 G50 2 submenu 3 Dialog windows 3 1 The file open window It is used for file open save in the command window and
23. n the right side of the top region 4 2 Creating new G code Open the file which you want to modify and press the insert Mac button Add the number of the new G code in the popup dialog after the G character example G123 Click the newly added G code in the textbox under the macro and we can define the path of the image after the click on the Edit Param Use characters to add directory For example G123 G123_basic bmp If the name of the image same the name of the G code we can add it automatically with the A button on the right side In case of Ok button the change is displayed in the center of the screen Press the Default help button and write the help text into the new window Press the Insert param button if you want to add parameter address After that press the Edit param button to modify the path of the image for the parameter If there is no input the G code image will be displayed We can add the text address of the parameter by the Editbox text If we want to use combobox we can create value with Insert Before and Insert After buttons which commutable with mod button and deletable with del button We can modify the default image and default help file with the Default Bmp and Default help button and the images and helps of the parameters with the Edit Bmp and Edit help button 4 3 Deleting Deleting parameter Select a parameter which you want to delete and click on
24. nu The other submenu of hole cycles F1 This submenu available from the Hole submenu We can find here additional G codes Cancel cycle state returning point and plane selecting G codes These G codes are detailed on Programmer s manual book The G80 function will cancel the cycle state the code will be inserted to the command window Back to the hole submenu with escape key from the other submenu The G83 G83 3 submenu F4 This submenu available from the Hole submenu These G codes are detailed on Programmer s manual book These buttons insert the G codes of the G83 G83 3 cycles If the Dialog submenu of the View menu is enabled then the parameters are displayed in the popup dialog Back to the hole submenu with escape key from the G83 G83 3 submenu The G84 G84 3 submenu F5 This submenu available from the Hole submenu These G codes are detailed on Programmer s manual book These buttons insert the G codes of the G84 G84 3 cycles If the Dialog submenu of the View menu is enabled then the parameters are displayed in the popup dialog Back to the hole submenu with escape key from the G84 G84 3 submenu The G86 G86 1 submenu F7 This submenu available from the Hole submenu These G codes are detailed on Programmer s manual book These buttons insert the G codes of the G86 G86 1 cycles If the Dialog submenu of the View menu is enabled then the parameters are
25. older view on the NC side then it will not refresh automatically Change view and change back to refresh 3 3 3 Copy from NC to floppy hard disk network F3 This function is enabled if one or more files are selected on the NC side and a folder is selected on the PC side The file name will be the program number and the extension will be nct 3 3 4 Copy from floppy hard disk network to NC F4 This function is enabled if one or more files are selected on the NC side 3 3 5 File selection to DNC mode F5 Select one file and no more on PC side Press F5 key Press PC NC key Press Program button on NC side Press the action menu key Press Run button Press DNC FEW button Press gt gt start lt lt on the control panel et ee O Select one or more file on PC side by using F6 Add them to the DNC list in the right order by using the Sort button F10 Press F5 key Press PC NC key Press Program button on NC side Press the action menu key Press Run button Press DNC FEW button ie ak eal a a 22 9 Press gt gt start lt lt on the control panel 10 After the program is finished the next program in the DNC list will start if gt gt start lt lt is pressed 11 The previous step can be repeated If the end of the DNC list is reached the first program will be started again 12 Anytime RESET is pressed twice and after that gt gt start lt lt is pressed the first program in the DNC list will b
26. to the other submenu with escape key from the G51 1 G50 1 submenu The G22 G23 submenu F4 This code group inserts the commands of the G22 G23 programmable stroke check functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the other submenu with escape key from the G22 G23 submenu User G code submenu F10 User User 4 ser 5 User 7 User 9 User G code create This code group inserts the commands of the User G code functions into the edit box Back to the other submenu with escape key from the User G code submenu The spindle submenu F9 ps S G6 G97 This spindle functions could be inserted with F1 F2 F10 buttons The dialog windows of spindle functions are detailed on Programmer s manual book Back to the main menu with escape key from the spindle submenu The G96 G97 submenu F1 This submenu available from the spindle submenu This code group inserts the commands of the G96 G97 constant surface speed functions into the edit box If the Dialog submenu of the View menu is enabled the parameters of the cycles are displayed in the popup dialog These functions are detailed on Programmer s manual book Back to the spindle menu with escape key from the G96 G97 submenu The G25 G26 submenu F3 This sub
27. tskasiobavens wwoptseadhontaisawepteandeenrenent 26 3 5 Toolfuncion WindOW ee eve en enkaa aaea 27 Defming user G codes esai e ates tensions eei a ea eare rarei a ean Ka ar rani 27 dl The man widow cearensis iir E EEEE ONN EEEN SEESE E ENEEK e E E Eia 27 d2 Creatine new Godge osertertc onsntsstes dee sete nren o ESENES EENE EEEN ESEESE ESK SEEN ESPE EEEa 28 A WCNC UII r E E E E A N EEA OEE 28 Special keys mentioned in this help pp 28 Information s for System administrators 4 29 6 1 Reinstallation Of Windows XP uu cccccccccccccceseceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 29 6 2 Installation of NCT Keyboard and mouse pp 29 6 3 Driver update for NCT keyboard and mouse pp 30 Produced and developed by NCT Ipari Elektronikai kft H1148 Budapest Fogarasi ut 7 Letters H1631 Bp pf 26 Phone 36 1 467 63 00 Fax 36 1 363 6605 E mail nct nct hu Home Page www nct hu 1 Introduction Before this program selling it had been tested accurately for months The current problems solving are on the Frequently Asked Questions page This is a new product so we are glad to hear any ideas and suggestions We pay attention to the current malfunctions This introduction aim is not to describe the basic manual of the Personal Computers or the Windows XP It aim is to detail of those functions which are different from a normal PC or useful with mouse less operations The manual of NCT controll
28. ut mouse like NCT controllers The buttons are reachable with F1 F2 F10 keys The buttons has two state enabled disabled If a button is disabled then its picture has gray color and ineffective The actual phrase is displayed in the edit window and it has always yellow background If this phrase starts with a G code which is displayed in the bottom keys also and there is no other G code in this phrase the corresponding editboxes of these parameters will be displayed otherwise this G code does not contain parameters Beside the editboxes is displayed the corresponding image in the image window area and help text in the help window area If the dialog window is changed then editbox will be changed automatically and conversely We can restrict this duplex write method to a simplex method but we can disable it too if it is necessary It available in the CodeWizard gt heading and Heading gt editor submenu 2 1 2 The main menu Meascyel User s Imitator The submenus of main menu are reachable with the F1 F2 F10 keys Back to the main menu with escape key The file submenu F1 The new F1 button deletes the command window and a new program frame will appear The program number and name are editable The open save save as functions are similar to Windows functions You can open a file from floppy hard disk network with the open F2 button You can save the contents of command window with save F3 and sav
29. x Back to the Technology submenu with escape key from the side submenu The rectangle submenu F1 Geometry Rough Bottom fin Side fin Chamfer This code group inserts the commands of the rectangle side machining functions into the edit box Back to the side submenu with escape key from the rectangle submenu The circle submenu F2 Rough Bottom fin Side fin Chanter Geometry This code group inserts the commands of the circle side machining functions into the edit box Back to the side submenu with escape key from the circle submenu The track submenu F3 e Geometry Rough EE Side fin Chanter This code group inserts the commands of the track side machining functions into the edit box Back to the side submenu with escape key from the track submenu The one submenu F4 Geometry Rough This code group inserts the commands of the rectangle side machining functions into the edit box Back to the side submenu with escape key from the One submenu The pocket submenu F4 E oon Square Circle Track Groove Select a submenu with F1 F4 key Back to the technology submenu with escape key from the pocket submenu The rectangle submenu F1 mh t a e E Demen Rough Bottom Side fin Chamber This code group inserts the commands of the rectangle pocket machining functions into the edit box Back to the pocket submenu with escape key from the rect
Download Pdf Manuals
Related Search