User Manual of “Sailfish” series Brushless Speed
Contents
1. 5 6 1 Running Mode Forward amp Backward 2 Timing Very Low Low High VHigh 3 Start up Acce Very Soft 2 8V C 4 Low Vol Cutof 2 6V C 3 2V C 3 4V C no protect Reverse High 5 Motor Div 6 Frequency STEP 4 Exit Program mode Disconnect the battery pack from the ESC to exit the program mode forcibly 2 Program the ESC with the Program Card Program card is an optional equipment for boat ESC it has 3 digital LEDs to show the programmable items and their values so the user interface is very friendly It is quite easy for programming the ESC with this small equipment Please read the user manual of program card for more information Trouble Shooting After power on motor does not work no sound is emitted The connection between battery pack and ESC is not correct Check the power connection Replace the connector After power on motor does not work such an alert tone is emitted beep beep beep beep Input voltage is abnormal too high or too low Check the voltage of battery pack The boat cannot run backward The ESC is not set to Forward and Backward in running mode The ESC cannot recognize the neutral point of throttle channel Program the ESC correctly Calibrate the throttle range again according to the instruction on page 1 The motor suddenly speed2. User Manual of Sailfish series Brushless Speed Controller for Boat Thanks for purchasing SAILFISH series Electronic Speed Controller ESC for boat High power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the correct use installation application or maintenance of our products Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation to compensation is limited to the invoice amount of the affected product Features 1 2 running modes Forward Only mode and Forward Backward mode for various of boats 2 5 steps of timing adjustment compatible with all kinds of sensorless brushless motor 3 Multiple protection features Low voltage cut off protection for lithium or nickel battery Over heat protection Throttle signal loss protection 4 Pocket sized Program Card can be purchased separately for easily setting the programmable items and online update Note 1 The program card is optional equipment for the ESC Programmable Items Note 2 The italics texts in the following form are the default settings Programmable Value Items 2 3 4 5 6 Forward 1 Running Mode Forward amp Backward Only Very 2 Timing Very Lo
3. ami 2 2 If you are using a flat Style transmitter a Move the throttle stick to the top position that is full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone can be heard that means the ful throttle position has been confirmed b If you want to set it to half range please move throttle stick to the neutral position a Beep tone can be heard that means the neutral position has been confirmed If you want to set it to full range in such a case the boat cannot run backward please move the throttle stick to the bottom position a Beep tone can be heard that means the position has been confirmed Now the throttle range setting process is finished The Normal Start Process Move the throttle stick to the neutral position or the bottom position and then turn on the transmitter Connect the battery pack to the ESC The motor emits several Beep tones to represent the cells number of your lithium battery pack Please make sure that the number is correct If only one Beep tone is emitted that means the Low voltage Cutoff Threshold is set to No protection mode for lithium battery otherwise the battery is very easy to be damaged Move the throttle stick upwards the motor begins to run and speeds up Program the ESC 1 Program the ESC with your transmitter4 Steps Enter Program mode Select programmable item Choose t
4. he new value of the selected item Exit STEP 1 Enter the program mode 1 Switch on the transmitter move the throttle stick to maximum position Full throttle position and then connect the battery pack to the ESC 2 Wait for 2 seconds the motor emits Beep Beep tone 3 The motor will Beep Beep tone repeatedly for 4 times that means the program mode is entered l STEP 2 Select the programmable item You will hear 6 groups of Beep tone circularly if you move the throttle stick to bottom position or the neutral position within 3 seconds after one kind of tones this item will be selected 1 Beep Running Mode 2 Beep Beep Timing 3 Beep Beep Beep Start up Acceleration 4 Beep Beep Beep Beep Low Voltage Cutoff Threshold 5 Beep Motor Diversion 6 Beep Beep Frequency Type l STEP 3 Choose the new value for the selected item After entering an item you will hear several tones in a loop Set the value matching to a tone by moving the throttle stick to the maximum position Full throttle position when you hear the tone then a special tone emits means the value is chosen and saved in the ESC Keep the throttle stick at the maximum position Full throttle position you will go back to step 2 and you can select other items Cut off the power directly will exit program mode directly Programmable Value Items 1 2 3 4
5. rities and high RPM if you are using High frequency the motor will run more smoothly and faster but will cause more heat and switching to ESC Begin to use The New ESC Step 1 Connect the ESC motor receiver battery and servo accordingly Step 2 Throttle Range Setting Calibration In order to make the ESC fit the throttle range you must calibrate it for the following cases otherwise the ESC cannot work properly Begin to use a new ESC Begin to use a new transmitter Change the settings of neutral position of the throttle stick ATV or EPA parameters etc 2 1 Turn on the transmitter set the EPA AVT value of throttle channel to 100 and disable the ABS brake function of your transmitter if it does has this function If you are using a Futaba transmitter please set the direction of the throttle channel to REV 2 2 If you are using a Handgun style transmitter a Move the throttle stick to the maximum position e full throttle position and then connect the battery pack to the ESC after 2 seconds Beep Beep tone can be heard that means the full throttle position has been confirmed b The Beep Beep can be heard for 4 times repeatedly during this time release the throttle stick to the neutral position a special Beep tone can be heard that means the neutral position has been confirmed Now the throttle range setting process is finished Ta Boar B
6. s down even if at the full throttle situation The ESC has entered the low voltage cutoff protection mode The ESC is over heat Replace the battery pack right away Stop running the boat for several minutes to cool the ESC The motor cannot start up but jibber only Motor wire and ESC output wire connection is incorrect ESC or motor is damaged Check if the connection of wires are correct or not Change new ESC or Motor The motor runs in the opposite direction The connection between ESC and the motor need to be changed Swap any two wire connections between ESC and motor Favourite Electronics Shenzhen Co Ltd Sa Sak RIIT E Zz DOH in Tt BRE PE AB X tele Tb J H i 86 755 61168885 61168882 amp H 86 755 61168887 JE www szfvt com IK 48 sales szfvt com 1 2 7
7. w High High 3 Start up Very Soft Accelerate 4 Low Voltage No 2 6V C 2 8V C 3 2V C 3 4V C Cutoff Protection 5 Motor Div 6 Frequency Forward Low Reverse High 1 Running Mode Forward Only Forward and Backward 2 Timing Very Low Low Middle High Very High Please select the most suitable timing value according to the motor you are just using The correct timing value makes the motor running smoothly And generally higher timing value brings out higher output power and higher speed but more heat 6 gt 3 Start up Acceleration Very Soft Soft Accelerate 4 Low Voltage Cutoff Threshold 2 6V 2 8V 3 0V 3 2 3 4 No protection 1 If you are using Lipo battery pack the ESC will automatically calculate the No of Battery cells For example if you are using a 3 cell Lipo pack and set the cutoff voltage as 3 0V cell then the cutoff value will be 3 0 3 9 0V 2 If you are using NiMH or NiCd battery they are not easy to be damaged usually you needn t worry about the over discharge problem so you can set this programmable item to No Protection 5 Motor Rotation Forward Reverse In most cases motor rotation is usually reversed by swapping two motor wires However in cases where the motor cables have been directly soldered the ESC cables motor rotation can be reversed by changing the value of setting on the ESC 6 Frequency Type Low High For motors have more pola
Download Pdf Manuals
Related Search