DATOSPIR MICRO Models B and C
Contents
1. 5 gt WWW SI Once the maneuver is finished the values of the FVC and FEV1 parameters appear on the top right hand of the screen underneath the REFerence values theoretical If three or more maneuvers have been performed and the FVC and or FEV1 parameters blink on and off this indicates that repeatability criterion has been fulfilled for one or both parameters This criterion indicates that the two best FVC or FEV1 values do not differ by more than 150 ml if FVC is more than 1 liter or more than 100 ml if FVC is less than or equal to one liter The device allows us to perform any number of necessary maneuvers The DATOSPIR MICRO always stores the five best maneuvers for Forced Vital Capacity FVC and orders them according to ATS ERS criteria so that M1 is the best and M5 the worst Press on AXES to switch from one graphic type to the other Flow Volume or Volume Time Press on PARAMETERS to view the screen containing the data of the selected maneuver Press on a MANEUVER to select it This allows you to see a graphic consult parameters or print out a report Press on the GRAPHIC area to delete the regular keys and enable the magnifying key and use e or e to enlarge or reduce Press on the same area again to return to the regular keys view Press on the REFERENCE area to access the patient s data To view the second set of keys press gt and to return to the first set of keys press2. Remember that the ka key can be used to return to the menu without losing the available infor mation except if a new patient code is entered or on certain other occasions but a warning is always displayed before loosing the data If the warnings are enabled once the maneuver is finished one or more WARNINGS may appear on the screen indicating that the maneuver has not been performed according to one or more ATS ERS criteria FP This indicates that expiration did not end satisfactorily because the variation of accumulated volume during the last second of the maneuver was over 25 ml or that the maneuver lasted for less than 6 seconds in individuals 10 or older or less than 3 seconds in children under 10 EX This indicates that the expiration did not start satisfactorily because the extrapolated volume was greater than 5 of the FVC or 0 15 liters According to the ATS ERS recommendations this volume should be lower than 5 of the FVC or 0 15 liters whichever is greater WARNING The DATOSPIR MICRO always stores the five best Forced Vital Capacity FVC maneuvers and these are ordered according to ATS ERS criterion meaning that M1 is the best and M5 the worst Therefore to present the diagnosis print the report or save the maneuver for POSTbronchodilation or for the internal DataBase it is recommendable to use M1 unless the technician deems it convenient to use a different one KJ D d C 0318 Producto clase Ila seg n
3. Directiva 93 42 CEE E E i SIBEL S A Rossell 500 08026 Barcelona Spain National Sales Office Tel 93 436 00 08 E mail comercial sibelmed com TA International Sales Office Tel 34 93 436 00 07 E mail export sibelmed com SIBEL S A pertenece a b e cs After Sales Service Tel 34 93 433 54 50 E mail sat sibelmed com www sibelgroup com Fax 34 93 436 1611 www sibelmed com 511 A21 091 Rev 1 S be med quick reference guide DATOSPIR MICRO Models B and C Thank you for purchasing a SIBELMED spirometer SIBELMED is a leading manufacturer of spirometry technology SIBELMED spirometers are supplied with multiple functions that allow absolute control and maximum comfort while performing spirometry maneuvers This is a concise guide that will allow you to perform the basic functions quickly For maximum performance refer to the USER MANUAL Installation Location The DATOSPIR MICRO is totally portable and autonomous and does not require special installation Be careful not to use the equipment in places that Are not safe for the patient or can cause patient stress Can be subject to splashing of water or other liquids Are subject to strong air currents Once the batteries have been placed correctly the equipment is ready to operate Use products that are certified in accordance with directive 93 42 CEE which ensure the patient s safety and the quality of the spirometers MY F
4. IRST SPIROMETRY step by step A Perfoming a FVC Forced Vital Capacity maneuver 1 Start the equipment by pressing gt 1 second 2 The MAIN SCREEN appears 3 Press the Fue key to view the screen to enter patient parameters a numeric or alphanumeric screen will appear depending on the mode selected 4 Enter the patient s parameters and press A screen containing the axes for plotting the maneuver will appear 5 After having instructed the patient and the patient is ready for the maneuver press the a key and wait until a blinking arrow T appears on the screen THE FVC MANEUVER CAN NOW BE STARTED F eb om WWW SI O PTS E PTS Dn WARNING As soon as the technician presses the RH key the patient has 30 seconds to begin the maneuver If the patient does not begin the maneuver during this time the equipment switches to standby and the key must be pressed again B VIEWING THE RESULTS of the maneuver Press on the parameters area A screen containing the data of the maneuver and the following keys appears Return to the B screen Change the maneuver JE View the diagnostic of selected maneuver Print out the report for the selected maneuver fal Save the maneuver in the database Use or ha to view the remaining parameters that have been selected C Viewing the DIAGNOSIS 1 Press the JE key to view the screen that displays th
5. e diagnosis one of the two diagnostic screens types provided with the equipment will appear depending on the mode selected 2 Use the Re or al key to switch between diagnoses D SAVING a test to the DB internal DataBase 1 Select the maneuver you wish to save 2 Press the E key to view the message SELECT BASE 3 Press the E key in the SELECT BASE area to view the message MANEUVER N X SAVED To save a test in PREbronchodilation for comparison with POSTbronchodilation mode follow the same steps described above but at step 2 press the Ey key to view the message MANEUVER PRE N X SAVED E PRINTING a maneuver 1 Make sure that the printer is properly connected and ready to operate and select the maneuver you wish to print 2 Press the Al key and a progress bar will appear indicating that the printing process is activated F DELETING a maneuver 1 Select the maneuver you wish to delete 2 Then press le to view the message YOU ARE GOING TO DELETE THE MANEUVER ARE YOU SURE 3 If you are sure press the key to view the message MANEUVER N X DELETED indicating that the selected maneuver has been deleted G Para CAMBIAR de paciente 1 Press the tl key to access the patient data screen 2 Enter the new patient data or modify existing patient data and press the key le This option allows you to enter a new patient or modify existing patient data If you have modified existing patient data the changes wi
6. he number of cigarettes the patient smokes per day divided by 20 and multiplied by the number of years the patient has been smoking cigarettes per day x years smoking 20 This field can be omitted if desired C d Number of cigarettes smoked per day This helps to calculate the COPD index parameter Et F Between 80 and 120 The Ethnic Factor is used in populations that do not have their own reference parameters and use existing population parameters that are adjusted according to a certain percentage This factor MUST BE 100 WHEN NOT APPLIED OTHER DATA OF INTEREST The FVC and FEV1 REFerence parameters appear on the top right hand side depending on the patient data entered in the equipment Ei This indicates the maneuver selected and indicates the current maneuver ab ab 2 me
7. ll be applied and the patient s parameters will be calculated again Information regarding the STRUCTURE OF THE SPIROMETER FUNCTIONS TREE To better understand the structure of the DATOSPIR MICRO spirometer the first level of the functions tree is shown below The structure of models B and C is characterized by graphic menus Operation Mode Bronchodilation Database SPIROMETRY Customization SpO2 Calibration Maintenance Printing DO NOT use sharp To facilitate navigation through the menus the equipment is provided with instruments that may a Pointer to select the icons keys that appear on the screen damage the screen We recommend using the pointer to select the character number or letter to fill in the numeric or alphanumeric fields DESCRIPTION OF CERTAIN FIELDS Code This is a 10 character numeric or alphanumeric field depending on the customized option for the patient s code Name A 20 character alphanumeric field for the patient s name This field can be omitted if desired Age Number of years between 4 and 100 Sur A 25 character alphanumeric field for the patient s surname s This field can be omitted if desired Cm Height between 50 and 230 Kg Weight in kg between 15 and 200 Sex Male or Female Technician A 10 character numerical field for the code of the technician performing the test This field can be omitted if desired Fuma Between 0 and 200 The Smoker Index equals t
Download Pdf Manuals
Related Search