User manual - Audio Authority
Contents
1. 3 092. Options Help Settings Macros TR devicecode Install module JV Enable status LED on IR activity JV Flash status LED on low battery level IR receiver a Note Using external IR receiver requires external powersupply ie DC 9 12Vdc eller USB SV power 1 Disconnected e If any changes are made to the configuration they need to be written to the device by pressing the SAVE button e To restore factory settings select the menu option OPTIONS gt RESTORE DEFAULT SETTINGS This will erase all custom settings and restore default values including any custom macros which may have been defined 5 1 SETTINGS TAB Enable status LED Selects if the LED should light up when receiving valid on IR activity IR commands from an IR remote Flash status LED Selects if the LED should flash briefly to indicate low on low battery level battery level IR receiver Selects if IR should be received through the internal Internal External IR receiver OR through an externally connected IR receiver both cannot be active at once If an external IR receiver is used BlueBeam must be powered by USB or DC adaptor not batteries 5 2 MACROS TAB Select macro Command The macros tab allows the user to define Power off D Jes POWERTOGGLE D Default NONE X 10 custom macros which will execute a sequence of commands by activating hoe y only one IR command The power off macro is a predefined macro which will ho
3. and date of purchase proof of purchase must be submitted with the defective unit to constitute a valid in warranty claim Units that fail after the warranty period has expired may be returned to the factory for repair at a nominal charge if not damaged beyond the point of repair All freight charges for out of warranty returns for repair are the responsibility of the customer Units returned for repair must have a Return Authorization Number assigned by the factory This is a limited warranty and is not applicable for products which in our opinion have been damaged altered abused misused or improperly installed Audio Authority makes no other warranties either expressed or implied including limitation warranties as to merchantability or fitness for a particular purpose Additionally there are no allowances or credits available for service work or installation performed in the field by the end user 7 1 WARRANTY SERVICE PROCEDURES If you suspect a product defect contact Audio Authority s Technical Service Department at 800 322 8346 or 859 233 4599 for assistance in verifying the problem If a defect or potential defect is suspected a replacement unit will be shipped immediately on a defect exchange basis and a Return Authorization Number will be issued for the return of the defective product Replacement units are sent out at the Manufacturer s Suggested Retail Price which is debited to the Customer s Credit Card at the time of s
4. receiver and wired IR input optional IR receiver available e May be powered via two AA batteries included USB connection to the PS3 or an optional 9 12V power adapter ordered separately Model 571 013 e Automatic low power mode for extended battery life e Low battery indicator e Easy battery change by removing two o rings no tools necessary e Senses PS3 power on and off via USB connection e Advanced customization possible using PC software via a USB interface e Configurable IR device code avoids conflicts with other Sony DVD players e Custom macro capability for power off etc e Firmware upgrade capable including Bluetooth firmware upgrades e Activity indicator LED for user feedback e Ultra compact case design allows small footprint and easy battery change 2 0 CHECKING PACKAGE CONTENTS Before connecting the C 1071 please make certain the following items are in the shipping carton Note Please retain the original packing material e C 1071 BlueBeam converter in case you need to return the unit If you find any items are missing contact Audio Authority e Two AA batteries immediately Have the model number and User manual invoice available for reference when you call 3 0 INSTALLATION The installation procedure described in this manual is for preparing a Logitech Harmony remote control for use with the Sony PlayStation 3 Other remotes may also be used with a similar setup procedure 4 3 1 CONFIGURING THE I
5. N is a registered trademark of Sony Computer Entertainment Inc Sony is a registered trademark of Sony Corporation All other trademarks are the property of their respective owners 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 Model C 1071 BlueBeam IR to Bluetooth Signal Converter Table Of Contents Introduction 4 Checking Package Contents 4 Installation 4 UsingBlueBeamSoftware 6 Troubleshooting 8 Specifications 9 Limited Warranty 10 Regulatory Compliance 11 Contact Information 11 1 0 INTRODUCTION Thank you for purchasing a Model C 1071 BlueBeam from Audio Authority The BlueBeam is designed to allow a Sony Playstation 3 to be integrated into an IR remote control system The PS3 accepts only Bluetooth commands but the BlueBeam allows any universal IR remote capable of learning the PS3 commands to control the PS3 This guide focusses on the Logitech Harmony remote but other learning remotes or home control systems may be used Audio Authority offers an extensive line of audio and video switchers converters distribution amps and extenders available for purchase online at www audioauthority com or through authorized dealers 1 1 FEATURES e Allows full control of DVD Blu ray playback and power on off e Infrared optical
6. R REMOTE CONTROL Using the Logitech Harmony software e Select the DEVICES tab and then ADD DEVICE e Select GAME CONSOLE gt GAME CONSOLE WITH DVD from the device selections box e Select AUDIO AUTHORITY from the manufacturer selections box e Enter the name BLUEBEAM in the model name box e Select NEXT and NEXT to finish For information on how to add the BlueBeam to Activities in the Harmony Remote see the Harmony manual 3 2 PAIRING THE BLUEBEAM WITH THE PS3 e Turn off the BlueBeam by removing the batteries and disconnecting the power supply and or USB cable e Turn on the PS3 system and use the PS3 controller to select the following option SETTINGS gt ACCESSORY SETTINGS gt REGISTER BD REMOTE e Set the BlueBeam within 30 feet of the PS3 and power on the BlueBeam insert batteries connect power supply or USB connection to power e When power is applied the red LED starts flashing to indicate that the BlueBeam is ready to be paired with the PS3 Make sure the BlueBeam is the actively selected device on the Harmony IR remote control Press and hold the 2 button on the remote do this within 20 seconds of BlueBeam power on Hold the 2 button down until the PS3 changes screen to REGISTERING e The BlueBeam is now paired with the PS3 and ready to convert IR signals to Bluetooth Which power source is best for my installation The BlueBeam can be powered from the PS3 USB port but the PS3 does not supply
7. User Manual BlueBeam IR to Bluetooth Signal Converter Model C 1071 AudioGpAuthority Audio Dauthority FE Ce WARNINGS e Read these instructions before installing or using this product This product should be installed by gualified personnel Do not expose this unit to excessive heat Install only in dry indoor locations Clean the unit only with a dry or slightly dampened soft cloth LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects Audio Authority cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use It is the responsibility of the user of the hardware to check that it is suitable for his her requirements and that it is installed correctly All rights are reserved No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical including photocopying recording or by any information storage or retrieval system without the written consent of the publisher Audio Authority reserves the right to revise any of its hardware and software following its policy to modify and or improve its products where necessary or desirable TRADEMARKS Audio Authority and the double A symbol are registered trademarks of Audio Authority Corp Copyright February 2009 BlueBeam is a trademark of Audio Authority Bluetooth is a trademark of Bluetooth SIG Inc PLAYSTATIO
8. am IR device code the BlueBeam can be configured to respond to another IR device code In order to do this connect the BlueBeam to a PC using a USB cable with a mini USB connector Open the BlueBeam software and select the IR device code tab change the device code from DVD1a to DVD2a or other in the selection box and press Save In the Harmony Remote software add a new device with the model name BLUEBEAM DVD2a to allow control of a BlueBeam with the IR device code DVD2a Logitech Harmony selection Device Game Console gt Game Console With DVD Manufacturer Audio Authority Model BLUEBEAM DVD2a BlueBeam does not respond to any IR remote commands e Make sure that power is supplied to the BlueBeam either by batteries check battery charge DC adapter or USB connection e Using an external IR receiver the BlueBeam must be set up via the BlueBeam PC software to activate the external IR port the internal IR receiver is turned off Call Audio Authority for the wired IR jack pin out e Using built in IR receiver the BlueBeam PC software must be set to INTERNAL IR the default setting if the front panel IR window is to be used The IR jack is inactive under this setting e Make sure that the IR device code specified in the BlueBeam software matches the IR remote control used Try loading the factory settings in the BlueBeam software to reset all settings to default e If using a Logitech Har
9. hipment Once we receive the defective unit back at the factory it will be evaluated under the conditions of this warranty and if found to be in warranty a full credit will be issued to the Customer s Credit Card Return freight charges for the defective unit are the customer s responsibility Please contact our Technical Service Department for complete details concerning all in and out of warranty service matters We appreciate your confidence in our products and services and will always strive to meet or exceed your needs 10 8 0 REGULATORY COMPLIANCE The C 1071 BlueBeam has been tested for compliance with CE and FCC rules and regulations The Power Adaptor Supply included has been tested for compliance with UL CUL CE PSE and GS regulations and guidelines This product and its power supply are RoHS compliant 9 0 CONTACT INFORMATION If you have questions or require assistance with this product in areas not covered by this manual please contact Audio Authority using the information below Audio Authority Technical Service 800 322 8346 M F 8 30 AM to 5 00 PM EST International 859 233 4599 Fax 859 233 4510 Send email to support audioauthority com Audio Authority Corporation 2048 Mercer Road Lexington Kentucky 40511 1071 USA 11 Audio Authority 2048 Mercer Road Lexington Kentucky 40511 1071 Phone 859 233 4599 Fax 859 233 4510 Customer Toll Free USA amp Canada 800 322 8346 www audioauthority com E 088
10. mony or other universal remote control make sure the BlueBeam device is selected as the currently activated device If problems persist contact the Audio Authority Technical Support department via email support audioauthority com or call 800 322 8346 US and Canada or 859 233 4599 6 0 SPECIFICATIONS Dimensions Unit 85x45x34mm 3 3x1 8x1 3 inch Packaging 112x69x37mm 4 4x2 7x1 5 inch Weight Unit 53g 1 870z Gross 121g 4 280z Temperature Range 0 45 Celcius Relative Humidity 15 95 Non condensing Placement Do not place in direct sunlight Optional DC Power Supply 9 12Vdc min 100mA Audio Authority Part 571 013 Batteries 2 x AA alkaline LR6 standard batteries included Expected Battery Life 6 12 months of normal use Expected battery lifetime is approximate Actual battery life depends on battery type model usage scenarios etc PC System Requirements Windows 2000 Windows XP Windows Vista 32 and 64bit or later Min 2MB free hard disk space Min 32MB free memory Min 1 free USB 1 1 or 2 0 port 7 0 LIMITED WARRANTY Ifany consumer product from Audio Authority fails due to defects in materials or workmanship within one year from the date of the original sale to the end user Audio Authority guarantees that we will replace the defective product at no cost Freight charges for the replacement unit will be paid by Audio Authority ground service only A copy of the invoice showing the item number
11. power to its USB port when it is powered off Therefore you will not be able to turn on the PS3 from your IR remote control if it does not have an additional power source If you do not wish to use an external DC adapter Model 571 013 use two AA batteries to power the BlueBeam when the PS3 is off The BlueBeam will automatically draw power from the USB port when the PS3 is on This way you can control the PS3 as normal and you do not need an external DC adapter Also battery life will be increased since power is supplied by the USB port whenever the PS3 is turned on Installing or changing batteries Batteries are not required but may be important for best functionality see above To change or remove the batteries remove the two o rings lift the top cover no tools are required and lift the batteries from the battery holder Replace them with two AA alkaline batteries or use external power as described above 4 0 USING AN EXTERNAL INFRARED RECEIVER Order the special IR receiver from Audio Authority to work with the BlueBeam if extended IR is required Other IR receivers do not function with the BlueBeam 5 0 USING BLUEBEAM SOFTWARE In order to use the BlueBeam software the BlueBeam must be connected to a PC using a USB 2 0 cable with a mini USB connector on the BlueBeam end The BlueBeam uses existing Windows drivers and does not require any additional drivers to be installed before using the software HEIR to Bluetooth v1 11 File
12. ring the code manually 5 4 INSTALL MODULE TAB Allows for future features to be downloaded as a firmware upgrade 6 0 TROUBLESHOOTING GUIDE BlueBeam will not pair with my PS3 The BlueBeam must be within 30 feet of the PS3 for operation Make sure all power supplies are completely removed DC adapter USB and batteries inside the BlueBeam case before trying to pair the BlueBeam and PS3 Also make sure that the PS3 screen says Press ENTER START to begin pairing When all power sources are removed the BlueBeam should start flashing for 20 seconds when connecting either DC adaptor USB or batteries Within 20 seconds while the LED flashes press and hold the 2 button on the Harmony remote the LED on the BlueBeam should be constant on until the PS3 says Registering If you let go of the 2 button before the PS3 has registered the BlueBeam you must start from the beginning by removing power from the BlueBeam If the above does not work try the following e Change the remote control batteries e Power the BlueBeam directly from a DC adapter or USB e Make sure the BlueBeam device is selected as the active device in the Universal Remote Control e Hold the remote control in front of the IR window of the BlueBeam with approximate three inches distance while holding the 2 button BlueBeam conflicts with my existing Sony DVD player If you have an existing Sony DVD player that conflicts with the default BlueBe
13. we H execute a power off sequence which will power off the PS3 by pressing only one button on the IR remote Selects which of the 10 macros to edit Command Selects which IR command to execute Duration Specifies the time in milliseconds to activate the current command Pause Specifies the time in milliseconds to pause until the next command should be sent Default The default button resets the currently selected macro to its default values 5 3 IR DEVICE CODE TAB By default the BlueBeam responds to IR codes from the device code Sony DVD1a but this can be changed to Settings Macros IR devicecode Install module any Sony device code For ease it is possible to select the most commonly used device codes directly from the Ets DyDla Default D selection box Make sure that you 26 73 DVD1a Default have a remote that is able to transmit lui 29 e 26 34 DVD2a the selected codes or the BlueBeam 26 250 DYD3a will not respond Custom If you have an existing Sony DVD player that conflicts with the default BlueBeam device code change the device code from DVD1a to DVD2a in the selection box and press Save In the Harmony Remote software add a new device with the model name BlueBeam DVD2a to allow control of a BlueBeam with the IR device code DVD2a MIR to Bluetooth v1 11 File Options Help A custom IR device code can be entered by selecting the Custom entry from the selection box and ente
Download Pdf Manuals
Related Search