HoopMaster Printed Instructions
Contents
1. the base with a 1 4 drill bit Position the mounting base over the pre drilled holes and secure it to the table with 4 1 4 20 x 2 1 2 bolts washers and wing nuts not provided The washers should go on the underside of the table Page 2 of 5 HOOPING INSTRUCTIONS HOOPING ON THE STATION First place the HoopMaster fixture on the station as shown in Figure 1 Notice the number that the document hole in the fixture circles You can use this number to document placement for repeat orders Number 19 is a good starting point for the fixture Adjust the outer ring of your hoop for the thickness of material you are hooping Next place the outer ring in the HoopMasiter fixture Lift the magnetic flaps and place the backing material over the outer ring Lower the flaps to hold the backing material in place If more or less holding is needed on the backing turn the screw in the center of the magnet out 1 4 turn for more holding and in 1 4 turn for less holding A little adjustment is all that is needed EEECAUTION THE MAGNETS ON THE FLAPS ARE VERY STRONG KEEP COMPUTER DISKS AWAY FROM THE MAGNETS Next pull the garment over the station The garment should be over the lower ring but under the flexible arms of the fixture Straighten the garment on the station Take note of the letter reference guide at the top of the station to repeat the same garment position next time you hoop Place the tubular hoop on the top of the support2. way to visualize the finished product Placement for this guide provided by Helen Hart Momsen For more information on placement go to www helenhart com Here you will find information on two books written by Helen Hart Momsen These books are true reference books that will be welcome on the shelf of any embroidery business large or small new or established One entire chapter of Stitching by Design is devoted to logo placement on almost any type of garment you will embroider Page 2 of 2
3. HoopMaster Instructions Midwest Products Inc W194 N11665 McCormick Dr Germantown WI 53022 www hoopmaster com Station Adjustment The HoopMasier station is pre assembled when you receive it It can be adjusted to three different angles for hooping When you receive the station it will be flat This position can be used for hooping items like towels and blankets You would load the garments onto the station like a silk screen press operator Position the station on your table so that the top of the station is closest to you Then pull the garment over the Station It may take some time to get used to hooping this way but this saves a lot of extra motion in the hooping process because you do not have to reach up and over the Station to pull the shirt on To adjust the station angle simply remove the wing nut and thumb screw from each side of the station bottom You may find this easier if you flip the station over so that it is upside down Then adjust the bracket to the new position and replace the thumb screw and wing nut If you do not want to hoop flat then the best setting is the middle angle To hoop this way you would position the station on the table so that all of the markings are right side up The high angle is not as good because it makes you bend your wrists to far back to push the hoop down This will cause more strain on your wrists over time We only offer this angle for a few customers that like to hoop this w
4. W194 N11665 McCormick Dr Germantown WI 53022 Phone 262 257 0930 Fax 262 257 0934 www hoopmaster com E a E 10 23 01 T E HoopMaster Logo Placement Here are some starting numbers know some of our customers use Please remember these are only a starting point for the fixture Placement will change for different brands and sizes of garment as well as different sizes of logos Ladies Mens Small C 11 C 15 Medium C 11 C 15 Large C 15 E 19 XL C 15 D or E 20 2XL E 20 F 20 3XL E 20 F 24 We suggest that you use the guide on the next page to figure out where the logo should be placed on your first shirt Then put a chalk mark or piece of tape on your first shirt where you want the logo Next put the inner ring amp backing material in your fixture Then pull your shirt over the station until your seams hit the top of the station Adjust your fixture so the center of the hoop is over the mark when you push the hoop down Then look at the number the fixture is circling and the letter the top of the collar is pulled down to The letter is very important because it sets the height of the logo on the shirt You can then document the letter and number for future jobs You can usually use this same setting for three sizes of shirts Start with the middle size for your setup and then you can usually go to one size larger and one size smaller Example if you have Medium Large and XL shirts Make your mark on the Large and get your fixture s
5. ay If you have any questions or problems please give us a Call Midwest Products Inc W194 N11665 McCormick Dr Germantown WI 53022 Phone 262 257 0930 Fax 262 257 0934 Website www hoopmaster com Page 1of5 Assembly of the FreeStyle Arm Mounting Base There are two different ways to use the FreeStyle Arm Mounting Base You can mount it to the portable base hardware provided or mount it directly to a table Hardware not provided Assembly on the Portable Base Figure 1 Place the sides of the portable base on the table with the bends towards the inside Then place the mounting base on top of the sides Use the 1 25 1 4x20 bolts and nuts to attach the top to the sides Hand tighten the nuts on the bottom Then use a phillips head screw driver to tighten the bolts from the top If the nut spins on the bottom use a 7 16 wrench to hold it Mount to Table hardware not provided This is an alternate way to mount the base Most customers use the portable version shown above To install the freestyle arm mounting base Select a desired position on your worktable For best results the worktable should have at least a 1 1 2 overhang edge Position the mounting base along the front edge of your worktable with the black knob to the back Make sure the mounting bolts and wing nuts will have clearance underneath the table before drilling Use the base as a template to locate the holes on the table Drill through the holes of
6. e hoop down against the garment and use the grid to accurately align the pocket or stripe It is also a great tool for lining up text to existing logos The pocket guide is only available for some hoop sizes at this time The T square is used on the fixture when it is on the freestyle arm The T square is to assist you in measuring the horizontal distance from the edge of a garment to where the center of a logo is to be embroidered It is screwed into the 2 brass thread inserts on the fixture Adjust the T Square by sliding it from side to side Place the desired measurement that you want to use over the center line of the fixture Then tighten the two thumb screws to hold the T square in place Do not over tighten To use the T square pull the part of the garment you want to measure from to the end of the T square by the zero Then pull the edge of the garment parallel to one of the fixture lines Backing Material Size We suggest using pre cut backing with your HoopMaster fixture To find the correct size backing Maximum Size for your fixture you will have to measure for the minimum and maximum size you can use For the maximum size open the magnetic flaps then measure from one side of the fixture to the other and from the hinge of one flap to the hinge of the other flap These dimensions are the maximum size you should order The minimum size is figured by measuring between the magnets You want to make sure the backing will be able to c
7. et up You should be able to do the Medium and the XL at the same placement If you go up or down 2 sizes from where you started you will probably want to mark a shirt and check the placement again 19 is a good starting point for a lot of shirts but you really have to check the first set Once you have the placement for a logo on a certain brand of shirt it is very easy to setup You can not make a generic chart that will fit all brands of shirts and all logos Shirts and logo size vary to much as well as customer preference lf you need any more information please give us a call Midwest Products Inc 1 800 900 0741 For more information on placement go to www helenhart com Here you will find information on two books written by Helen Hart Momsen These books are true reference books that will be welcome on the shelf of any embroidery business large or small new or established One entire chapter of Stitching by Design is devoted to logo placement on almost any type of garment you will embroider Page of 2 Left Chest Placement Measure down in a straight line from where the shoulder seem and the collar or ribbing meet 7 9 Distance from join of shoulder for men and 5 7 for women s garments Measure seem and collar is 5 7 women over from the center of the shirt to that line usually 7 9 Men 4 5 Place the center of the design at the intersection For a child s garment measure down about 5 AN over about 3 When the
8. he unit s or part s is are returned to us with transportation charges prepaid Replacement parts supplied during the product warranty period are warranted only for the balance of the original product warranty period In no event Shall Midwest Products Inc be liable for any loss profits incidental indirect special or consequential damages under any circumstances or for expenses occasioned by the use of any defective product This warranty does not cover damages resulting from accident misuse or abuse lack of reasonable care the affixing of any attachment not provided by Midwest Products Inc any alterations to the product or improper handling installation and or maintenance This warranty is VOID unless any repair necessary is made by Midwest Products Inc by one of its authorized distributors or by a third party under the express written permission of Midwest Products Inc The obligation of Midwest Products Inc under this warranty is limited to repair or replacement of the product in accordance with the terms of this warranty If repair or replacement is not a viable alternative Midwest Products Inc s liability shall be limited to reimbursement of the original invoice price of any goods that it does not repair or replace There are no warranties offered by Midwest Products Inc other than those herein described Coverage under this limited warranty does not include incidental or consequential damages Midwest Products Inc
9. ing arms making sure that the hoop locks in the center position on the arms You may have to slide the hoop slightly back and forth to get it to lock in Press the hoop downward with your palms near the center section of the hoop Not on the ends of the hoop arms When pressure is released the hoop will lift out of the bottom of the fixture Remove the garment by grasping the hoop and lifting it off of the arms towards the top of the station USING THE FIXTURE ON THE FREESTYLE ARM First loosen the black thumbnut on the mounting base a few turns it is not necessary to remove it all the way Place the freestyle arm on the mounting base with the slotted part under the black knob The freestyle arm should then drop into place on the locating pin see Figure 2 Next place the fixture on the freestyle arm as shown in Figure 3 You are now ready to use the freestyle arm for cap backs sleeves bags and other small Items The engraved lines on the fixture are used to measure the vertical distance from the edge of a garment to the center of the hoop The lines are also used to make sure the garment is straight while hooping Freestyle Arm On Mounting Base Page 3 of 5 Pocket Alignment Guide The pocket alignment guide is to assist you in aligning logos with pockets horizontal Stripes or vertical stripes This is done by placing the pocket guide inside of the top hoop The pocket guide should lock in place square with the hoop Then press th
10. over all of the magnets See Figure 4 Please watch our online videos for more detailed instructions If you have any other questions feel free to contact us at 1 800 900 0741 or 262 257 0930 Visit our web site at www hoopmaster com for new product releases 9 2 11 Page 4 of 5 Part names These are pictures of parts that may have been included in your kit Use this sheet if you need to call and discuss parts that you have or need to get These parts are not included with every order most are optional Optional Items 4 1 4 20 x 1 25 Bolts for Mounting Base and 4 nuts e Ze Station Full Front Fixture Mighty Hoops 5 5 shown F a fo Ao a fof Online Video Training go to www hoopmaster com and www mightyhoop com If you do not have high speed internet please call for a copy of our DVD Normal HoopMaster systems do not include hoops you use your existing hoops lf you ordered Mighty Hoops then you can use them with special fixtures or without fixtures 7 22 13 Page 5 of 5 7 HoopMaster E Limited Warranty Midwest Products Inc warrants this product to be free from any defects in material and or workmanship for a period of one 1 year from the date of the original sale This warranty is only valid to the original retail purchaser Midwest Products Inc agrees to repair and or replace any part found to be defective by us without charge provided that t
11. shirt has no placket or other structure measure down the center of the shirt parallel to the first line Then measure to the vertical line usually 4 5 You can make a template of a placket out of cardboard or plastic to use as a marker Use the snaps or button on jackets as a guide Between the second and third snap button works well Use the bottom of a V neck as a guide To place a design on the left and right chest use the document grid on your HoopMaster First find the placment on one side then note the number the fixture is circling and the letter the shirt is pulled down to Then use the same number and letter on the other side of the garment when hooping Center Back Back placement is dictated by the size of the designs and the jacket Close the jacket and place it face down on the worktable Measure 3 to 4 inches from the seam at the bottom of the collar Add half the height of the design to find the center It will usually turn out to be 8 to 10 inches down from the center back collar seam to the center point of the design 8 10 to For a child s jacket the center will usually fall between 5 and 8 inches down from the collar A distance of 2 5 inches from the collar to the top of the design is a good rule of thumb Add half the height of the design to find the center of the embroidery As with any design placement use a model or a mannequin to verify your decisions An actual size sew out placed on the back is a good
Download Pdf Manuals
Related Search