Wall Unit Rangehood User Manual
Contents
1. 100 If you press V button again red color percentage is displayed on the screen for example G 10 The color displayed on the screen may be set from 0 to 100 percent by pressing Tmr and Tmr buttons it may be set rapidly by pressing longer When you press V button for 5 seconds new color is recorded a beep sounds and setting mode is turned off To exit from setting mode without saving you may press Mot off or lamp buttons Control area Variant 4 hood is not operated Press V button for 5 seconds to bring the back light to always on condition Blue Red Green Color Light Turquoise Pistachio Green Green lt Purple Black and white display 10 Orange Auto ee3688 ee3688 The icon for the option currently operating on the hood shall be active and displayed in white as shown in the figure above Other icons shall not be displayed Slider screen It shall always be active with a white color This screen operates with slide and drop logic When the hood starts to operate with the 1st speed appliance shall be brought to 2nd speed when the screen is slid and dropped once and this procedure shall be repeated until the appliance reaches the required speed The reverse of this procedure shall be applied to decrease speed While setting the timer and dimmer if you press the timer inscription on the glass seven segments shall start to flash on the digital screen 88 When the user moves2. Motor switch should bi Check lamps Lamps should be firm Check outlet Outlet should be open replaced witha ne condition o lt lt e co o 5 k o g v o oO Cooker hood does not direct at places without chimney Table 1 TECHNICAL SPECIFICATIONS Feeding Voltage 220 240 V 50Hz Motor Isolation Class Isolation Class CLASS
3. appliance is plugged in the outlet and that the fuses are OK If the Lighting Does Not Operate Ensure that the appliance is plugged in the outlet and that the fuses are OK e Check the bulbs Always unplug the appliance during this check Tighten if the bulbs are loosened you may replace them if they do not turn on although you have tightened them Possible Faults and Things To Do Before Contacting the Service A If the appliance does not operate anyway Check the fuse that the appliance is connected and main fuse of your home Check whether the hood is plugged and whether the plug is fully seated on the outlet B If the performance of the appliance is not enough or operates loudly Is the outlet diameter of the flue adequate min 120 mm Are metal filters clean Check it Ensure that the carbon filters are not older than 6 months if you are using the hood flueless Make sure that your kitchen is adequately ventilated to ensure the air flow Contact authorized service if the performance of your appliance does not still satisfy you n Voltage of t cted to grounc month at norn network should be between 220 24 hood should be conne ch 2 3 months at ctio w one ea models with Carbon Filter s eck motor switch Motor switch should bi t oker 2 o fc oo oo Check aluminum filter Aluminum Casse Filter should be washed once a Check Carbon Filter Carbon filter should Check motor switch
4. appliances e g gas oil wood or coal stoves water heaters etc take the combustion air from the installation place and discharge the waste air with a waste gas system e g flue With the hood being operated air is taken from the kitchen and neighbouring rooms A vacuum is generated if adequate air supply is not ensured Poisonous gases are sucked back from the flue and discharge gas duct and re entered to the house in such a condition m Therefore you shall always ensure that clean air intake is always adequate Risk of fire Due to the sparks fluttering around Appliance is allowed to be installed over a heating appliance operated with solid fuel e g wood or coal only if there is a cover available that cannot be removed Current building codes and regulations of the local power and gas companies shall be considered for the installation work Risk of electric shock Due to damaged connection cable Do not kink or pinch the connection cable during installation Risk of injury There is a risk of injury due to the sharp edges during installation work Always use protective gloves during installation work of the appliance Risk of injury Due to the dropping of the appliance Always fix all safety bolts and safety covers properly Cleaning and protective maintenance Risk of being burnt Risk of electric shock Due to the appliance Allow the appliance to cool before any cleaning or maintenance Disconnect t
5. function of 15 minutes shall be activated if you press any of the motor operating buttons for more than 2 seconds A signal shall be given on the display when the timer starts and motor shall be turned off automatically after 15 minutes ii 5 LoL 3 speed Lamp On Off 2 speed Control area Variant 3 x pees wae og o 7 a o o a FILTER 1 mom BEBE is ite oom Filter Cleaning Warning warning Symbol Turning on the fan Variant 1 Press the On Off button Increase the fan level with button or reduce the fan level with button 1 Hood off timer If the timer is set during the operation of the motor hood is turned off i e motor is stopped lamp is turned off and buzzer sounds for 5 seconds when time set in the timer ends TMR Button This button allows setting the timer by increasing the hour digit of timer start time The hour digit on timer is increased by 1 with each press and it is increased rapidly if you press the button longer TMR Button This button allows setting the timer by decreasing the hour digit of timer start time The hour digit on timer is decreased by 1 with each press and it is increased rapidly if you press the button longer Alarm timer Alarm timer is started if the timer is set when the motor is not operated In other words buzzer sounds for 15 seconds only when timer ends motor and lamp are not turned off even if motor or lamp are opera
6. his her finger slowly to the right keeping the finger pressed on the screen the value on the screen shall increase up to 99 with increments of 1 User shall apply the reverse of this procedure to reduce the value Same procedure applies for dimmer feature OOn off Icon When you touch this icon hood starts to operate and fan icon on the digital screen 2 shall start to rotate and 93 seven segments shall be activated Timer Icon The timer icon on the digital screen shall be activated when you touch this icon 4 Lamba Simgesi Lamp Icon The lamp icon on the digital screen shall be activated when you touch this icon To activate dimmer feature user shall hold his her finger pressed on the lamp icon as in the oie products E WASH FILTER After 60 hours of operation this icon shall be illuminated on the screen User may remove this icon from the screen by pressing the on off button after cleaning the filter 88 Speed This icon shall be activated when the appliance is operated Also dimmer and timer values shall be shown here This explanation applies to models with touchscreen slider switch Control area Variant 5 OOO Q Q D a ald 74 1 2 3 4 5 1 Press this button to turn on the appliance 2 Press this button to operate the appliance in 3rd speed 3 Press this button to operate the appliance in 3rd speed 4 Press this button to operate the appliance in 3rd speed a iene this button to turn
7. where the exhaust of this appliance is placed or the device shall be of hermetic type Use pipes with a diameter of 150mm or 120 mm when you use flue connection for your appliance Pipe connection shall be as short as possible and have minimum number of elbows Do not allow your children to play with the appliance Do not allow little children to use the appliance Use MAX 6A fuses on the hood installation for your safety Keep package material away from children as they may pose a risk If the power cord is damaged it shall be replaced by the manufacturer or its authorized service or by an equally qualified technician to prevent any risky condition WARNINGS AND SAFETY PRECAUTIONS In case of any fire de energize the hood and any other cooking devices and cover the fire Do not use water to put off the fire When the cooking appliances are being operated accessible parts may become hot This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervised or instruction concerning use of the appliance by a responsible person for their safety The distance between the appliance and the stoves should not be less than 65 cm in electric stoves and not less than 75 cm in gas and other types of stoves when the hood installation is completed Exhaust of the hood shall not be con
8. e circumference of the body Figure 13 A n pp iance may have single flue on some model options In this case you may procure the inner flue suitable for your appliance from your authorized dealer 11 Operation This manual applies to several appliance variants some specifications described here may not apply to your appliance Note Turn on the hood when you start cooking and turn it off only after a few minutes later than you have finished cooking The vapor inside the kitchen is removed most effectively in this way Control area Variant 3 Fan level indicator enter ww O Z Fan On Off Fan Level Fan Level Reduction Increase Lamp On Off Turning on the fan Variant 1 Press the On Off button Increase the fan level with Hutton or reduce the fan level with button Illumination You may turn on or off the illumination irrespective of the fan Timer When you press this button for more than 2 seconds a timer function of 15 minutes shall be activated display shall signal when the timing function has started and motor shall stop automatically after 15 minutes This explanation applies to models withS speed digital switch and models with touchscreen on the glass Control area Variant 2 Fan level indicator Fan On Off 1 speed Turning on the fan Variant 1 Press the On Off 1st speed button Illumination You may turn on or off the illumination irrespective of the fan Timer A timer
9. f f Wall Unit Rangehood User Manual IK50 IK71 IK80 IK82 IK90 26 18 Charlies Way Frankton Hamilton New Zealand 3204 Ie www ikoncommercial co nz FOR BETTER LIVING i Published May 2015 TECHNICAL DRAWINGS Min 90 600 60 562 Max 90 950 60 942 WARNINGS AND SAFETY PRECAUTIONS This appliance is intended for home usage Operating voltage of your appliance is 220 240 Volt 50 Hz A grounded plug is installed on the power cord of your appliance This cord shall always be plugged to a grounded outlet Electrical installation shall be performed by a qualified electrician Installation by unqualified persons may cause operation with low performance damage to the appliance or accidents Power cord shall not be crushed or smashed during installation Do not route the power cord near the stoves cord may melt and cause fire Do not plug the appliance before installation of the appliance Make sure that the plug is easily reachable in order to unplug the appliance in case of any danger Do not touch the lamps of your appliance when they have operated for a long time Lamps may burn your hand as they may be hot Kitchen hoods are intended for home usage only with normal cooking There is a risk of fault and it shall be void of warranty when it is operated for other purposes Comply with the regulations of the authorities on the discharge of outlet air This warning does not app
10. he fuse connection or remove the plug Caution m There is a risk of damage due to the humidity ingress in electronic components Do not clean the control elements with damp cloth m Surface may be damaged due to improper cleaning Clean the stainless steel surfaces on the brushing direction only Do not use stainless steel cleaners for control elements m Surface may be damaged due to abrasive or hard cleaning materials Never use abrasive or hard cleaning materials Maintenance and repair Risk of fire risk of injury Due to improper or out of rule repairs Disconnect the fuse connection or remove the plug Repair work shall always be performed by qualified personnel electronic technicians Risk of injury In case of a fault or damage on the appliance disconnect the fuse and remove the plug and call the authorized service Risk of fire risk of injury Due to damaged connection cable A damaged connection cable shall always be replaced by qualified personnel electronic technicians Risk of being burnt Risk of electric shock In case of a faulty bulb disconnect the fuse connection or remove the plug Replace the faulty bulbs immediately to prevent overloading of other bulbs allow the bulbs to cool first Cleaning and protective maintenance m Surface may be damaged due to abrasive or hard cleaning materials Never use abrasive or hard cleaning materials Cleaning of the appliance surface Procure the proper cleaning a
11. lters on a dishwasher loosely or freely Do not allow metal oil filters to be jammed Manual cleaning Note You may use a special fat solvent for heavily soiled filters You may buy this solvent from the online sales center m Soften the metal oil filters in hot water with dish soap m Use a brush for cleaning and rinse the filters thoroughly afterwards m Metal ya filtrelerdeki s v lar n iyice akmas n bekleyiniz Operating modes You may operate this appliance with discharge air mode and circulated air mode Discharge air mode Intake air is cleaned with oil filters and discharged through a pipe system u Note Waste air shall not be discharged neither to an active smoke or waste air flue nor to a flue used for the ventilation of rooms where heating appliances are installed m f you want to discharge the waste air to a non active smoke or waste air flue you shall take permission from an authorized chimney sweep m f the waste air is discharged through an outside wall a telescopic wall case shall be used Circulated air mode Intake air is cleaned with oil filters and active carbon filter and returned back to the kitchen Note You shall install an active carbon filter to trap particles that cause odor in the circulated air mode For various possibilities to operate the appliance in circulated air mode please refer to the manual or consult your authorized dealer You may buy the accessories required fo
12. ly to flueless applications Do not cook flammable food under the appliance Operate your appliance after putting a pan pot etc on the stoves Otherwise high temperature may cause deformation of some parts of appliance Turn off the stove before removing a pan pot etc from the stoves Do not leave hot oil on a stove Pots with hot oil inside may catch fire by itself Oil may catch fire while you are frying etc watch for your curtains and linens Ensure that the filters are replaced in time Filters that are not replaced in time may cause a risk of fire due to the fat collected on them Do not use filtering material that are not resistant to flames instead of filters Do not operate your appliance without filters do not remove the filters while the appliance is operated In case of any fire de energize the hood and any other cooking devices De energize the appliance by unplugging it Your appliance may cause a risk of fire if the cleaning is not performed as per the specified periods De energize the appliance before any maintenance operations De energize the appliance by unplugging it Negative pressure inside the room when the electric stove top hood and other electrically powered devices are operated simultaneously shall not exceed 4 Pa 4X10 bar Any fuel or gas powered devices in the medium where your appliance shall be used such as room heaters shall be completely isolated from the volume
13. m cartridge filter Remove the faulty bulb and replace with a new one with the same rating Lamps may burn your hand when they are hot wait until they are cooled off In order to replace the lamp remove the glass cover on the lamp with an object that would not scratch the surface of the appliance as shown in Figure 16 Pull down and remove the faulty lamp and replace with a new one Figure 16 REPLACING THE LAMPS Disconnect the hood from mains Remove the power connection of LED lamp Press on the lamp with your hand to remove the lamps Remove the adhesive tape around the lamp frame from the body plate gt Before placing the new LED bulb remove the protective foil on the frame and stick it on its position on the appliance body Replacement of Glow Bulbs y Sen the hood from mains Remove the aluminum cartridge filter Remove the faulty bulb and replace with a new one with the same rating Lamps may burn your hand when they are hot wait until they are cooled off Figure 17 ee A 17 If the hood does not operate Before contacting the service Ensure that plug is installed on the outlet and that the power fuse in the installation is OK do not perform any operations that may damage the appliance Check your appliance as per Table 1 before contacting the service Contact your dealer or nearest authorized service if the problem is resumed 15 Before Contacting Authorized Dealer Ensure that the
14. n the hood cabinet before Figure 8 When the suspension procedure is completed tighten the suspension screws installed to the wall in Fig 6 with a screwdriver to prevent moving of the appliance Figure 9 6 Figure 9 After you have fixed your hood completely secure the body with a screw from the hole C inside the body to prevent it from moving Figure 10 Figure 10 NOTE If the hood seems skewed adjust the alignment of the hood by loosening the M5 screws that the suspension plates on the top are installed to ee l Figure 11 RN Tighten the inner flue to the flue installation plate secured on the wall from its upper external sides Figure 14 Installation of aluminum pipe Install the sa flexible aluminum pipe to the plastic flue Install the o i a P other end of the pipe to the flue hole on the wall ra Figure 12 es a W Ti Figure 12 Avoid bends and elbows as much as possible as the bends and elbows in the aluminum pipe shall reduce the air suction power Engage the flues to th
15. nd protective materials for your appliance from the authorized service Note Surface of the appliance and control units are delicate against scratches m Clean the surfaces with a soft damp cloth dish soap or a less active glass cleaning material Soften the dirt that is dried and stuck on the surface with a damp cloth Do not rub m It is not suitable to use dry clothes scratchy sponges materials that require rubbing cleaning materials with sand sodium carbonate acids or chlorine and other active agents m Clean the stainless steel surfaces on the machining direction only m Do not use stainless steel cleaners and damp clothes for control elements Cleaning metal oil filters Metallic oil filters used in the appliance traps the oil particles inside the humidity and vapour occurred in the kitchen Clean the metal oil filters every three months approximately with a normal level of operation 1 to 2 hours per day m Do not use over active cleaning materials with acid or javel solution m Clean the holding mechanisms of metal oil filters with a damp cloth while cleaning the metal oil filters m You may wash the metal oil filters with a dishwasher or manually In the dishwasher Note A light discoloration or change of color may occur when the filters are washed in a dishwasher This does not affect the function of metal oil filter m Do not wash heavily dirty metallic oil filters with other dishes m Place the metallic oil fi
16. nected to air ducts with other smoke You should be careful when the appliance is operated with other appliances that use the air in the room and their fuel e g heaters water heaters that operate with gas diesel fuel coke or wood etc Because hood may negatively effect the burning of the fuel as it exhausts the air inside the room This warning does not apply to flueless applications PPLIANCE POSITION eee SS Ln Min 65 cm Max 75 cm Figure 1 The distance between the appliance and the stoves should not be less than 65 cm in electric stoves and not less than 75 cm in gas and other types of stoves when the hood installation is completed Figure 1 Installation Removing the Appliance from its Package Check that your appliance is not deformed Report the transport issues immediately to transport operator Any faults encountered shall be reported to the dealer too Do not allow children to play with packing material INSTALLATION TEMPLATE as TAY Wes NY SS Standard accessories Optional accessories Vital risk risk of poisoning There is a vital risk of being poisoned due to the combustion gases sucked back Do not operate the appliance together with the air circulated fire appliances unless adequate air intake is ensured Air circulated fire
17. nstallation Screw these plates on M5 drive nuts on the cabinets with M5 x 40 screws before suspending the appliance Figure 2 Figure 2 Installation of the plastic flue to the hood Fix the plastic flue to the motor connection plate with a 3 5x9 5 screw Figure 3 Drilling of Suspension Holes Fix the installation template to the surface where the hood shall be suspended and drill holes in the points marked with A B C using a 8 mm drill bit Figure 4 Tap 10 mm plastic dowels to the holes you have drilled Figure 4 Drill the D E points with a 6mm drill bit to screw the flue installation plate referring to the min and max heights of the appliance Figure 5 Install 6 mm dowels to the holes you have drilled Figure 5 Tightening the suspension screws Tighten 5 5x60 suspension screws to 10 mm dowels A B you have tapped on the wall The distance between screw head and the wall shall be 5 mm Figure 6 Figure 6 Tighten the flue installation plate to the 6 dowels you have tapped to the wall using the 3 9x22 screw supplied with your hood Figure 7 10 De o eee SS a je _ EN Y a ae Figure 7 Suspending the Hood to the Wall Hold the hood from its body and suspend it to the wall on A and B points using the L plates you have fixed o
18. on lamps of the This explanation applies to models with push button switch Cleaning Periods for the Metal Filters Filters shall be cleaned every 2 to 3 weeks as per frequency of operation or when the C signal is shown on the display After cleaning and installing the filters press button when the appliance is turned off to remove signal C for more than 3 seconds E shall be indicated on the display and normal operation shall be resumed If you want to resume operation without removing the C signal active speed shall be displayed for 1 second when you press the button and C signal shall be displayed again and the motor shall resume operation C sign shall be displayed after 60 hours operation of the appliance Al explanation applies to models with djt switch 14 Control area Variant 6 Q N N A W ail AD UD UD 3 spd Push Pull Switch Positions Ais 5 spd Push Pull Switch Positions Push the button down and bring it to the desired position to select the desired speed of the appliance Replacement of Halogen Lamps A Disconnect the hood from mains To replace halogen bulbs press down from the rear side of the lamp socket and pull the lamp downwards then rotate it a little clockwise and remove it downwards Figure 15 Figure 15 Replacement of Glow Bulbs Disconnect the hood from mains Remove the aluminu
19. r this procedure from relevant Sales points authorized dealers or from the online sales center Refer to the end of operating manual for part numbers of the accessories Carbon Filter Active carbon filters shall be used for filtering the air inside the room and giving it back to the room in environments without a flue connection You may procure the active carbon filter from your authorized dealer or service De energize the appliance before replacing the carbon filter Carbon filter shall be replaced every 3 to 5 months based on the frequency of operation as it is used in kitchens without flue outlet Do not wash the carbon filter Always have oil filters installed on the appliance without respect to the availability of the carbon filter Do not operate your appliance without oil filter Replacement of carbon filterThere are 2 carbon filters on the appliance Rotate the carbon filter clockwise to install it Figure 1 Figure 1 Replacement of Aluminum Cartridge Carbon Filter Press on the upper catch and pull towards yourself to remove the carbon filter Figure 1a a E WZ Figure 1a Installation of the Appliance Installation of the suspension plate to the hood There are 2 L shaped suspension plates available in the installation accessories to suspend the appliance to the wall These plates are supplied with a screw set to provide ease of i
20. ted while the timer is set Timer clock displays the real time when the timer is not active Clock Real time is displayed continuously The colon between hours and minutes is flashed every 1 second Press the Tmr and Tmr buttons together for 2 seconds to set the clock Hours and minutes flash for 5 seconds You may set the clock by increasing organization decreasing the minutes by pressing the Tmr or Tmr 7 button while the flashing resumes Clock flashes until you press any button when the power is turned on You may set the clock by pressing Tmr or Tmr buttons while flashing resumes Settings are reset when power is Cut Filter Warning Clean filter warning is displayed after 60 hours of operation and flashes every 1 second You may reset the filter time and Clear filter icon by pressing M on off button for 3 seconds after cleaning and re installing the filters 2 Back light option Back light is turned on as factory default Optionally back light may be turned off by pressing V button for 5 seconds a beep sounds when the motor and lamp are turned off and timer is not set i e Programmable options may be set while the motor and lamp is turned off and timer is not set 1 Back light brightness settings When you press V button for 5 seconds blue color percentage is displayed on the screen for example B 00 If you press V button again red color percentage is 100 displayed on the screen for example R
Download Pdf Manuals
Related Search