Design Wash LED Zoom User Manual Ver 1
Contents
1. Test Channel Manual Control Calibrate Values User Mode Edit User Mode A Edit User Mode B Edit User Mode C Select Program Edit Program Edit Scenes Record Controller ETATIO EFFECT ADJUST USER MODE SETTING EDIT PROGRAM www elationlighting com FUNCTION Set DMX Address Adjust the desired DMX address via the Control Panel 1 Press MENU to access the main menu and press ENTER 2 Press UP DOWN until Set DMX Address is displayed and press ENTER 3 Current DMX address is displayed 001 499 press UP DOWN to select desired DMX address 001 499 then press ENTER to confirm selection and exit menu FUNCTION Value Display Display the DMX 512 value of each channel 1 Press MENU to access the main menu and press ENTER 2 Press UP DOWN until Value Display is disolayed and press ENTER 3 Press UP DOWN 16 select desired value Auto Program PAN PAN Fine TILT TILT Fine Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM All Channel then press ENTER to confirm selection and exit menu FUNCTION Set To Slave Define the fixture as a slave 1 Press MENU to access the main menu and press ENTER 2 Press UP DOWN until Set To Slave is disolayed and press ENTER 3 Press UP DOWN 16 select desired mode Slavel Slave2 Slave3 then press ENTER to confirm selection and exit menu FUNCTION Auto Program Define2. SS 2 LA a ZSA SS Se 9 SZ wy ZS SY ZS SS gt 6 SS ZXZ Fy ZS O SS Geo N 4 ZA 2 lt SZ PN ZS gt gt A g Z DEAN 2 5 7 gt M E me AX WHR 1 DESIGN WASH LED ZOOM User Manual ver 1 Ae D www elationlighting com CLAMP MOUNTING The DESIGN WASH LED ZOOM provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the Omega Bracket and attach at least one properly rated safety cable to the integrated safety cable rigging point in the base assembly 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener SECURING e Secure the clamp to the bracket using a M12 screw fitted through the 13 center hole e Insert the Turn Twist Locks of the first Omega bracket into the respective holes on the bottom of the device Tighten the Twist Locks a 1 4 turn clockwise e Install the second Omega bracket on the top of the device in the same way e Pull a safety cable through the holes on the bottom of the base and over the trussing system or a safe installation TZ This is very important to p
3. Temperature Info Software Version Status Setting Service Setting Fans Control Display Setting Temperature C F Initial Effect Reset Default Reset All Reset Pan amp Tilt FUNCTION INFORMATION PERSONALITY RESET FUNCTION www elationlighting com Test Functions Fine Adjustment of Functions 000 255 Password 050 Fine Adjustment of PAN Fine Adjustment of TILT Fine Adjustment of ZOOM Edit Channel Numbers For User Modes Preset User Modes Select Auto Programs To Be Run Testing Program Program In Loop Save And Exit Save And Automatically Return Manual Scenes Edit Automatic Scenes Recorder Auto Program PAN PAN Fine TILT TILT Fine Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM Auto Program PAN PAN Fine TILT TILT Fine Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM Password XXX 000 255 000 255 000 255 Password PAN TILT ZOOM Wash LED ZOOM User Mode A User Mode B User Mode C Auto Pro Partl Program 1 10 Program 1 Auto Pro Part2 Program 1 10 Program 2 Auto Pro Part3 Program 1 10 Program Test Step 01 SCxxx Step 64 SCxxx Auto Program PAN PAN Fine TILT DESIGN WASH LED ZOOM User Manual ver 1 Program 3 Program 1 Program 10 Edit Scene 001 Edit Scene 250 XX XX
4. Auto Speed Low Speed High Speed and press ENTER to confirm selection and press MENU to return to the previous menu 26 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com PERSONALITY Display Setting Shutoff Time Shut off the Control Panel display after 02 to 59 minutes default is 05 minutes 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Display Setting is disolayed and press ENTER 3 Press ENTER and Shutoff Time XxX is displayed 4 Press UP DOWN 16 select desired time OFF 02 59 and press ENTER to confirm selection and press MENU fo return to the previous menu PERSONALITY Temperature C F Display the temperature in Celsius or Fahrenheit default is Fahrenheit 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Temperature C F is disolayed and press ENTER 3 Press UP DOWN to select desired mode Celsius Fahrenheit and press ENTER to confirm selection and press MENU to return to the previous menu PERSONALITY Initial Effect Display the initial effect position for DMX functions 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Initial Effect is disolayed and press ENTER 3 Tap UP DOWN to select desired function Auto Program PAN PAN Fine TILT TILT Fine
5. 546 85 30 Fax 31 45 546 85 96 E mail support elationlighting eu WARRANTY REGISTRATION Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support at 323 582 3322 IMPORTANT NOTICE iT There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty Damages resulting from modifications to this fixture and or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and or repairs 5 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com Qa g g LIMITED WARRANTY A Elation Professional hereby warrants to the original purchaser Elation Professional products to be free of manufactur
6. Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM and press ENTER to confirm selection 4 Press UP DOWN 16 select desired position 000 255 and press ENTER to confirm selection and press MENU to return to the previous menu PERSONALITY Reset Default Restore factory settings function ON or OFF the default is OFF 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Reset Default is disclayed and press ENTER 3 Press UP DOWN 16 select desired mode ON OFF and press ENTER to confirm selection 27 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com RESET FUNCTION Reset fixture function Reset All or Reset Pan amp tilt Press MENU to access the main menu press UP DOWN until Reset Function is displayed and press ENTER Press UP DOWN to select desired mode Reset All Reset Pan amp Tilt and press ENTER to confirm selection l EFFECT ADJUST Test Channel Test each DMX function Press MENU to access the main menu press UP DOWN until Effect Adjust is disolayed and press ENTER Press UP DOWN until Test Channel is disolayed and press ENTER Press UP DOWN 16 select desired function Auto Program PAN PAN Fine TILT TILT Fine Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM and press ENTER to confirm selection l EFFECT ADJUST Manual Co
7. Running Time Fixture Last Times Clear Timer Password 038 Clear Fixture Last time Fixture Temperature Software Version Address Via DMX Auto Run If No DMX Pan Reverse Movement Tilt Reverse Movement Fine Resolution Switch Pan Degree Select 1 2 3 Movement Feedback Select Movement Mode Sensitivity of Microphone Service Password 050 Select Fan Voltage Select Fans Soeed Mode Display Shut Off Time Temperature Switch Between C or F Initial Effect Position Restore Factory Settings Reset All Settings Reset Pan amp iilt Settings ETATIO DESIGN WASH LED ZOOM SYSTEM MENU 001 499 Auto Program PAN PAN Fine TILT Slavel Slave2 Slave3 XXXX Hours XXXX Hours XXXX Hours Password XXX ON OFF XXX C F ON OFF Close Hold Auto Music ON OFF ON OFF ON OFF 630 540 ON OFF Speed 1 4 0 99 70 Password XXX HIGH LOW 02 60m 05m DESIGN WASH LED ZOOM User Manual ver 1 Master Alone Master Alone Current Time Total Life Hours Last Run Hours Timer Password Clear Last Run Head Temperature VX X Address via DMX No DMX Status Pan Reverse Tilt Reverse Fine Resolution Pan Degree Feedback Movement Speed Mic Sensitivity Service Password Fan Voltage Auto Fans Speed High Fans Speed Low Fans Speed Shutoff Time Celsius Fahrenheit PAN XXX ON OFF Set DMX Address Value Display Set To Slave Auto Program Music Control Time Information
8. UP DOWN to select desired value PAN TILT ZOOM and press ENTER to confirm selection press UP DOWN to select desired value 000 255 and press ENTER to confirm selection and press MENU to return to the previous menu USERS MODE SET USER MODE This function allows the DMX channels assignment to be changed from the default value of 13 to either 8bit 11 channels or extended mode at 13 channels This function also allows the user to create user defined channel orders allowing the fixture to match the channel order of other fixtures on the market for easier operation A total of three user modes may be configured User Mode A User Mode B and User Mode C EDIT USER MODE This function allows the user make the actual changes in the user defined modes that are created in the previous function EDIT PROGRAM The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller 29 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com SELECT PROGRAM This function allows the user to select one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run EDIT PROGRAM This function allows the user to edit the built in programs EDIT SCENCES Thi
9. a reset test program which brings all the motors to a home position before it is ready The display may show Err channel is XX if there are problems with one or more channels XX stands for channel 1 2 3 4 5 6 and 13 which have testing sensors for positioning For example when the display shows Err channel is PAN it means there is an error in channel 1 If there are errors on channel 1 channel 3 channel 6 at the same time you may see the error messages Err channel is PAN Err channel is TILT Err channel is RED LED flash 2 times and then the fixture will go through a second reset test program If the error messages remain after performing 2 reset tests only the channels that have errors will not work properly all other channels will work normally If after the third reset test program all the errors have not been resolved the fixture cannot function properly and therefore will place itself in a stand by mode until repairs are made PAN Error PAN Yoke Movement Error This message will appear after completing the motor reset if the PAN movement is not located in the default position after the reset This error can happen if the yoke s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepper motor or its driving IC on the main PCB is defective or fails TILT Error TILT Head Movement Error This message will appear after completing the motor reset if the TILT mo
10. the fixture mode Master or Alone for running Auto Programs Select the desired internal programs under Select Program set the number of steps under Edit Program and edit the individual scenes under Edit Scenes 1 Press MENU to access the main menu and press ENTER 2 Press UP DOWN until Auto Program is displayed and press ENTER 3 Press UP DOWN to select desired mode Master Alone then press ENTER to confirm selection and exit menu 20 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com FUNCTION Music Control Define the fixture mode Master or Alone for running Auto Programs via sound activation default is Master 1 Press MENU to access the main menu and press ENTER 2 Press UP DOWN until Music Control is disolayed and press ENTER 3 Press UP DOWN 16 select desired mode Master Alone then press ENTER to confirm selection and exit menu INFORMATION Time Information Current Time Display the running time of the fixture from last power ON The counter is reset after each time the device is powered OFF 1 Press MENU to access main menu press UP DOWN until Information is displayed and press ENTER 2 Press UP DOWN until Time Information is disolayed and press ENTER 3 Press UP DOWN until Current Time is disolayed and press ENTER again and XXXh Hours is displayed and press MENU to return to previous menu INFORMATION Time Information Total Life Hours Display the total run
11. 0Hz 350W Max Power Consumption 14 F to 113 F 10 C to 45 C APPROVALS RATINGS CE P20 c us Intertek Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice DESIGN WASH LED ZOOM User Manual ver 1 35 www elationlighting com PHOTOMETRIC DATA MIN ZOOM Distance 4 7 5 24 6 T32 a3 ux e a310 200 78 Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 36 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com DIMENSIONAL DRAWINGS or nae Hi 1 a Ol a 19 EE WML Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 37 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting m ELATIS elatio g g co CIRCUIT SCHEMATIC Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 38 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com OPTIONAL ACCESSORIES ORDER CODE ITEM TRIGGER CLAMP Heavy Duty Wrap Around Hook Style Clamp EWDMXSYSTEM Wireless DMX System 1 Transmitter 1 Receiver EWDMXT Wirel
12. DMX 512 CONTROLLER CONNECTION Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the DESIGN WASH LED ZOOM Please refer to the diagram below You can chain multiple panels together through serial linking The cable that should be used is two conductor shielded DMX cable with XLR input and output connectors Always be sure daisy chain your in and out data connections never split or Y your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch 4 DMX512 Sy 120 Ohms DMxX controller Address 1 Address 15 Address 29 14 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com DMX 512 CONNECTION WITH DMX TERMINATOR A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a terminator Elation part DMX T PACK will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistan
13. ELATION DESIGN WASH LED ZOOM user manual ih A O 3 v Ii PROFESSIONAL ETATIO DESIGN WASH LED ZOOM user manual www elationlighting com 2015 ELATION PROFESSIONAL all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ELATION brands and product names are trademarks or registered trademarks of their respective companies ELATION PROFESSIONAL and all affiliated Companies hereby disclaim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe insufficient and negligent assembly installation rigging and operation of this product Elation Professional USA 6122 5 Eastern Ave Los Angeles CA 90040 323 582 3322 323 832 9142 fax www elationlighting com info elationlighting com
14. Elation Professional B V Junostraat 2 6468 EW Kerkrade Netherlands 31 45 546 85 66 31 45 546 85 96 fax www elationlighting eu info elationlighting eu DOCUMENT VERSION IE Please check www elationlighting com for the latest revision update of this manual Document Software DMX Date Version Version Channel Modes Notes 2 2015 1 gt 1 2 0 14 Updated manual format 2 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com CONTENTS General Information 4 Warranty 6 Safety Instructions 7 General Guidelines 8 Fixture Overview Fixture Installation 10 Understanding DMX 13 Fixture Menu 17 DMX Channel Values 3 Error Codes 33 Cleaning and Maintenance 34 Technical Specifications 35 Optional Accessories 39 3 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com GENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The DESIGN WASH LED ZOOM has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance UNPACKING Thank you for purchasing the DESIGN WASH LED Z
15. OOM by Elation Professional Every DESIGN WASH LED ZOOM has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully insoect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting customer support at the number listed below Please do not discard the shipping carton in the trash Please recycle whenever possible BOX CONTENTS e 1 3 Pin XLR Cable e 1 Omega Bracket Holder e 1 Safety Cable Manual 8 Warranty Card 4 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com CUSTOMER SUPPORT Elation Professionale provides a customer support line provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions For service related issue please contact Elation Professional ELATION SERVICE USA Monday Friday 8 00am to 5 00pm PST Voice 323 582 3322 Fax 323 832 9142 E mail support elationlighting com ELATION SERVICE EUROPE Monday Friday 08 30 to 17 00 CET Voice 31 45
16. RSONALITY Status Settings Pan Reverse Reverse the PAN movement default is OFF 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Status Settings is displayed and press ENTER 3 Press UP DOWN until Pan Reverse is displayed and press ENTER 4 Press UP DOWN 16 select desired mode ON OFF and press ENTER to confirm selection and press MENU to return to the previous menu 23 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com PERSONALITY Status Settings Tilt Reverse Reverse the TILT movement default is OFF Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER Press UP DOWN until Status Settings is disclayed and press ENTER Press UP DOWN until Tilt Reverse is disolayed and press ENTER l 4 Press UP DOWN to select desired mode ON OFF and press ENTER to confirm selection and press MENU to return to the previous menu PERSONALITY Status Settings Fine Resolution Select desired DMX channel operation from 8bit 12 available DMX channels NO PAN TILT Fine Control Channels or 16bit 14 available DMX channels PAN TILT Fine Control Channels Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER Press UP DOWN until Status Settings is disolayed and press ENTER Press UP DOWN until Fine Resolution is disolayed an
17. cated in the DMX chain The DESIGN WASH LED ZOOM can be controlled via DMX 512 protocol and the DMX address is set via the control menu DATA CABLE DMX Cable REQUIREMENTS For DMX and Master Slave Operation Your fixture and your DMX controller require a standard 3 pin or 5 pin XLR connector for data input and data output see figure below If you are making your own cables be sure to use two conductor shielded digital DMX cable rated at 120 ohms this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers Your cables should be made with a male and female XLR connector on either end of the cable Also remember that a DMX line must be daisy chained and cannot be split unless using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch 4 13 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com DMX Output DMX Input DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 1 Ground 2 Data 2 Data A 0 3 Data 3 Data 4 Open 5 Open Be sure to follow the above figure when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR outer casing Grounding the shield could cause a short circuit and erratic behavior
18. ce N 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture 4 5 Pin XLR DMX CONNECTORS Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The following chart details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data Compliment signal Data True signal Pin 3 Not Used Fin 4 Do Not Use 15 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com DMX ADDRESSING All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture responds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion in other w
19. clayed and press ENTER 3 Press UP DOWN until Service Password is disolayed and press ENTER 4 Press UP DOWN 16 select 3 digit password and press ENTER to confirm selection and press MENU return to the previous menu PERSONALITY Service Setting Fan Voltage Select desired Fan Voltage setting Low for normal operation or High for extreme environmental operation temperatures default is Low Voltage IS Using fans in High mode will decrease the life of the fan over time 1 Enter the Service Password by following the steps in the above section 2 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 3 Press UP DOWN until Service Setting is disolayed and press ENTER 4 Press UP DOWN until Fan Voltage is displayed and press ENTER 5 Press UP DOWN 16 select desired mode Low Voltage High Voltage and press ENTER to confirm selection and press MENU to return to previous menu PERSONALITY Fans Control Select desired Fans Control setting default is Auto Speed Auto Speed default Fans automatically switch between High Speed PAN and TILT speeds identical to original Design Wash LED Pro Low Speed Increased PAN speed 0 5 seconds faster then original Design Wash 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Fans Control is disolayed and press ENTER 3 Press UP DOWN 16 select desired mode
20. connection with this product including warranties of merchantability or fitness are limited in duration to the warranty periods set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said periods have expired The consumer s and or dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professional be liable for any loss and or damage direct and or consequential arising out of the use of and or the inability to use this product G This warranty is the only written warranty applicable to Elation Professiondl products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published 6 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting m EEATIS elatio g g co SAFETY INSTRUCTIONS The DESIGN WASH LED ZOOM is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual This device falls under PROTECTION CLASS 1 It s essential this device be grounded properly Only qualified personnel should perform all electrical connect
21. d press ENTER l 4 Press UP DOWN to select desired mode ON OFF and press ENTER to confirm selection and press MENU to return to the previous menu PERSONALITY Status Settings Pan Degree Select desired maximum degree of PAN movement 540 or 630 default is 540 Press MENU to access the main menu press UP DOWN until Personality is disolayed and press ENTER Press UP DOWN until Status Settings is disolayed and press ENTER Press UP DOWN until Pan Degree is disolayed and press ENTER l 4 Press UP DOWN to select desired mode 540 630 and press ENTER to confirm selection and press MENU to return to the previous menu 24 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com PERSONALITY Status Settings Feedback Select desired Feedback setting which allows for automatic PAN and TILT movement correction in the event either one is disrupted during normal operation default is ON 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Status Settings is disolayed and press ENTER 3 Press UP DOWN until Feedback is disolayed and press ENTER 4 Press UP DOWN 16 select desired mode ON OFF and press ENTER to confirm selection and press MENU to return to the previous menu PERSONALITY Status Settings Movement Speed Select desired Movement Speed default is Speed 1 Speed 1 default Slower than orig
22. ess DMX Transmitter EWDMXR Wireless DMX Receiver AC3PDMX5PRO 5 ft 1 5m 3pin PRO DMX Cable AC5PDMX5PRO 5 ft 1 5m 5pin PRO DMX Cable Additional Cable Lengths Available 39 DESIGN WASH LED ZOOM User Manual ver 1
23. ffect In Sequences 160 191 Shutter OPEN ALL LEDs O 192 223 Random Strobe Effect SLOW to FAST 224 255 Shutter OPEN ALL LEDs O 0 255 Intensity 0 to 100 COLOR MACROS NO Function 8 39 Color Macro 1 40 71 Color Macro 2 72 103 Color Macro 3 104 135 Color Macro 4 136 167 Color Macro 5 168 199 Color Macro 6 200 231 Color Macro 7 232 255 Color Crossfade SLOW To FAST 0 255 Zoom 31 DESIGN WASH LED ZOOM User Manual ver 1 CHANNEL 1 www elationlighting com ETATiIomw PROFESSIONAL ELATION DESIGN WASH LED ZOOM DMX Channel Values Functions 14 DMX Channels Specifications are subject to change without any prior written notice VALUE FUNCTION 0 79 Normal 80 84 ALL Motor Reset 85 87 SCAN Motor Reset 88 99 NO Function 100 119 Internal Program 1 Scene 1 8 120 139 Internal Program 2 Scene 9 16 140 159 Internal Program 3 Scene 17 24 160 179 Internal Program 4 Scene 25 32 180 199 Internal Program 5 Scene 33 40 200 219 Internal Program 6 Scene 41 48 220 239 Internal Program 7 Scene 49 56 240 255 Sound Control Scene of Program 1 32 DESIGN WASH LED ZOOM User Manual ver 1 CHANNEL www elationlighting com ERROR CODES When the fixture is powered ON it automatically enters
24. inal Design Wash LED Pro for smoother more precise movements Speed 2 PAN and TILT 5066065 identical to original Design Wash LED Pro Speed 3 Increased PAN speed 0 5 seconds faster then original Design Wash LED Pro TILT soeed is the same 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Status Settings is displayed and press ENTER 3 Press UP DOWN until Movement Speed is displayed and press ENTER 4 Press UP DOWN 16 select desired mode Speed 1 Speed 2 Speed 3 Speed 4 and press ENTER to confirm selection and press MENU return to the previous menu PERSONALITY Status Settings Mic Sensitivity Select desired Microphone Sensitivity from 0 to 99 default is 70 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Status Settings is disolayed and press ENTER 3 Press UP DOWN until Mic Sensitivity is disolayed and press ENTER 4 Press UP DOWN 16 select desired mode 00 99 and press ENTER to confirm selection and press MENU to return to the previous menu 25 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com PERSONALITY Service Setting Password The Password is 050 1 Press MENU access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Service Setting is dis
25. ing defects in material and workmanship for a period of two years 730 days and Elation Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months 180 days from the original date of purchase This warranty excludes discharge lamps and all product accessories This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the Elation Professional factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty Elation Professional will pay return shipping Charges only to a designated point within the United States If any product is sent it must be shipped in its original package and packaging material No accessories should be shipped with the product If any accessories are shipped with the product Elation Professional shall have no liability what so ever for loss and or or damage to any such accessories nor for the safe return thereof C This warranty is void if the product serial number and or labels are altered or removed if the product is modified in any manner which Elation Professional concludes after inspection affec
26. ions KEEP THIS FIXTURE AWAY FROM RAIN AND MOISTURE UNPLUG POWER BEFORE SERVICING FIXTURE NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILETIC SHOCK 5 A A e For proper operation follow the Installation guidelines described in this manual Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts brackets holders clamps safety cables included with this fixture should be used for installation Any modifications will void the original manufactures warranty and increase the risk of damage and or personal injury e Never look directly into the light source of this fixture to prevent risk of injury to your retina which may induce blindness Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times e The fan and air inlets must remain clean and never blocked Allow approx 6 15cm between this fixture and other devices or a wall for proper cooling e Always disconnect from main power source before performing any type of service and or cleaning procedure Only handle the power cord by the plug end never pull out the plug by tugging the wire portion of the cord e Do not operate this fixture if the power cord has become frayed crimped and or damaged If the power cord is damaged replace it immediately with a new one of similar power
27. l controller and power ON Set the DMX value of Channel 1 on the controller to 7 Set the DMX value of Channel 2 on the controller to 7 or 8 When set to 7 the DMX address can be set between 1 and 255 When set to 8 the DMX address can be set between 256 and 511 4 Using Channel 3 on the controller set the desired DMX address of the fixture Example 1 the desired DMX address is 57 set Channel 1 to a value of 7 set Channel 2 to a value of 7 and then set Channel 3 to a value of 57 Example 2 If the desired DMX address is 420 set Channel 1 to a value of 7 set Channel 2 to a value of 8 and then set Channel 3 to a value of 164 256 164 420 5 After setting Channel 3 to the desired DMX address value wait for approximately 20 seconds for the fixture to complete the address reset function PERSONALITY Status Settings No DMX Status Fixture runs in Auto Run if NO DMX signal is detected Options include Hold Close Shutter Music Control Auto Program default is Hold 1 Press MENU to access the main menu press UP DOWN until Personality is displayed and press ENTER 2 Press UP DOWN until Status Settings is displayed and press ENTER 3 Press UP DOWN until No DMX Status is disolayed and press ENTER 4 Press UP DOWN to select desired mode Hold Close Shutter Music Control Auto Program and press ENTER to confirm selection and press MENU to return to the previous menu PE
28. ning time of the fixture from initial power ON 1 Press MENU access main menu press UP DOWN until Information is displayed and press ENTER 2 Press UP DOWN until Time Information is disolayed and press ENTER 3 Press UP DOWN until Total Life Hours is disolayed press ENTER again and XXXh Hours is displayed and press MENU to return to the previous menu INFORMATION Time Information Last Run Hours Display the running time of the fixture from its previous cycle 1 Press MENU to access main menu press UP DOWN until Information is displayed and press ENTER 2 Press UP DOWN until Time Information is disolayed and press ENTER 3 Press UP DOWN until Last Run Hours is displayed press ENTER and XXXh Hours is displayed and press MENU to return to the previous menu 21 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com INFORMATION Time Information Timer Password Display the timer password 038 Press MENU to access main menu press UP DOWN until Information is displayed and press ENTER Press UP DOWN until Time Information is disolayed and press ENTER Press UP DOWN until Timer Password is disolayed and press ENTER l 4 Press UP DOWN to select 3 digit password and press ENTER to confirm selection and press MENU to return to the previous menu INFORMATION Time Information Clear Last Run Clear the last run time of the fixture default is OFF A correct password m
29. ntrol Manual control of each DMX function Press MENU to access the main menu press UP DOWN until Effect Adjust is disolayed and press ENTER Press UP DOWN until Manual Control is disolayed and press ENTER Press UP DOWN to select desired function Auto Program PAN PAN Fine TILT TILT Fine Move Speed Red LED Green LED Blue LED White LED Strobe Dimmer Rainbow ZOOM and press ENTER to confirm selection Press UP DOWN 16 select desired value 000 255 and press ENTER to confirm selection and press MENU to return to the previous menu 28 DESIGN WASH LED ZOOM User Manual ver 1 1 www elationlighting com EFFECT ADJUST Calibrate Values Fine adjustments to PAN TILT and ZOOM A correct password must be entered in order to make adjustments The Password is 050 This function should only be performed by a technician familiar with the operations of this fixture This function allows small adjustments to be made to the motor alignments to compensate for wear Improper use of this function can result in undesired operation Please contact Elation Customer Support for further instructions 1 Press MENU access the main menu press UP DOWN until Effect Adjust is displayed and press ENTER 2 Press UP DOWN until Calibrate Values is disolayed and press ENTER press ENTER again and Password is displayed press UP DOWN to select 3 digit password and press ENTER fo confirm selection 3 Press
30. ords changing the settings of one channel will affect all the fixtures simultaneously listen to the a different DMX address each unit will start you set each fixture channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture In the case of the DESIGN WASH LED ZOOM which is a 14 Channel fixture you should set the starting DMX address of the first unit 1 the second unit to 15 1 14 the third unit to 29 15 14 the fourth unit to 43 29 14 and so on Note During start up the DESIGN WASH LED ZOOM will automatically detect whether a DMX data signal is being received or not If DMX data signal is being received the display will show Addr XXX XXX representing the actual DMX address If the fixture is not receiving a DMX signal the display will flash If your fixture is connected to a DMX controller and the display is flashing not receiving a DMX signal please check the following The 3 PIN or 5 PIN XLR input plug cable with DMX signal from controller is not connected or is not inserted completely into the DMX input jack of the fixture The DMX controller is switched off or defective The DMX cable or connector is defective A DMX terminator has been inserted into the last fixture in your DMX chain 16 DESIGN WASH LED ZOOM User Manual
31. rating 7 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com GENERAL GUIDELINES NEVER OPEN THIS FIXTURE WHILE IN USE During the initial operation of this fixture a light smoke or smell may emit from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time This fixture is a professional lighting effect designed for INDOOR DRY LOCATIONS ONLY on stage in nightclubs theatres etc Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating to prevent any fire hazard The fixture must be installed in a location with adequate ventilation at least 1 5 feet 5m from adjacent surfaces Be sure no air ventilation slots are blocked DO NOT attempt installation and or operation without knowledge how to do so DO NOT permit operation by persons who are not qualified to operate this type of fixture Most damages are the result of operations by nonprofessionals Consistent operational breaks may ensure the fixture will function properly for many years to come DO NOT shake fixture avoid brute force when installing and or operating fixture Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environment always use mounting hardware that is no less than M10 x 25 mm also be sure the hard
32. re to any surface make sure the installation area can hold a minimum point load of 10 times the weight of the fixture 210 Ibs 95 kg e Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable e Never stand directly below the device when mounting removing or servicing MOUNTING The DESIGN WASH LED ZOOM is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface see illustration on the next page Be sure this fixture is kept at least 1 5 feet 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails 10 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com MOUNTING POINTS Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure the fixture is kept at least 0 5m 1 5 feet away from any flammable materials decoration etc SESE SES 1 A ZON ZN X znz We af _ SI Ss JY 2 v SZ ZS ZN lt lt S Se af S
33. revent the fixture from dropping if the clamp fails 12 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com UNDERSTANDING DMX DMX 512 DMX is short for Digital Multiplex This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactures to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and data OUT XLR terminals located on the fixtures most controllers will only have output jacks DMX LINKING To ensure proper DMX data transmission always use proper DMX cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a starting DMX address of 1 may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is lo
34. s function allows the user to edit or define the actual scenes that are stored in the user defined built in programs that are accessed in the previous step REC CONTROLLER The DESIGN WASH LED ZOOM features an integrated DMX recorder Pre programmed scenes can be transmitted to the fixture via any DMX compliant controller This function allows those scenes to be stored in to the fixture s built in memory and then subsequently used to create the user defined programs 30 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com ETATIomw DMX CHANNEL FUNCTIONS AND VALUES ELATION DESIGN WASH LED ZOOM DMX Channel Values Functions 14 DMX Channels Specifications are subject to change without any prior written notice VALUE FUNCTION PAN MOVEMENT 8 Bit PAN Movement PAN MOVEMENT 16 Bit 0 255 0 255 Fine Control Of PAN Movement O 8 B 0 255 TILT Movement TILT MOVEMENT 16 Bit Fine Control Of TILT Movement SPEED PAN TILT MOVEMENT 0 255 0 225 Max To Min Speed 226 235 Blackout By Movement 236 255 NO Function RED LEDs 39 Total RED 0 Black 255 100 GREEN LEDs 29 Total 0 255 0 255 GREEN 0 Black 255 100 B D 0 Tota 0 255 BLUE O Black 255 100 WHITE LEDs 10 Total 0 255 WHITE O Black 255 100 0 31 shutter CLOSED ALL LEDs OFF 32 63 Shutter OPEN ALL LEDs O 64 95 Strobe Effect SLOW to FAS 96 127 Shutter OPEN ALL LEDs O 128 159 Pulse E
35. ting e Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall e Check for any deformations on the housing color lenses rigging hardware and rigging points ceiling suspension trussing Deformations in the housing could allow for dust to enter into the fixture Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person s e Electric power supply cables must not show any damage material fatigue or sediments Never remove the ground prong from the power cable 34 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com ETATIomw TECHNICAL SPECIFICATIONS FEATURES High Output Pro Grade Zoom Wash LED Luminaire 5 500 Total Lumens 6 23 Motorized Zoom RGBW Color Mixing and Color Macros Flicker Free Operation for Broadcast TV and FILM SOURCE 108 3W Osram LEDs 40 Red 28 Green 30 Blue and 10 White 50 000 Hour Average LED Life EFFECTS RGBW Color Mixing and Color Macros Dimming 0 100 Strobe 1 18fps CONTROL CONNECTIONS 14 DMX Channels 4 Button Control Panel LCD Menu Display 8 16 Bit Resolution Adjustable Movement 3pin and 5pin DMX In Out SIZE WEIGHT Length 13 4 341mm Width 8 7 220mm Vertical Height 17 5 445 Weight 21 0 Ibs 9 5 kg ELECTRICAL THERMAL AC 100 240V 50 6
36. ts the reliability of the product if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional if the product is damaged because not properly maintained as set forth in the product instructions guidelines and or user manual D This is not a service contract and this warranty does not include any maintenance cleaning or periodic check up During the periods as specified above Elation Professional will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of Elation Professional All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that effect E Elation Professional reserves the right to make changes in design and or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with the products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professional in
37. ust be entered in the Timer Password menu in order to clear last run time Press MENU to access main menu press UP DOWN until Information is disolayed and press ENTER Press UP DOWN until Time Information is disolayed and press ENTER Press UP DOWN until Clear Last Run is disolayed and press ENTER Press UP DOWN to select desired mode ON OFF and press ENTER to confirm selection and press MENU to return to the previous menu l INFORMATION Temperature Info Head Temperature Display the temperature of the fixture default is Fahrenheit Press MENU to access main menu press UP DOWN until Information is displayed and press ENTER Press UP DOWN until Temperature Info is disolayed and press ENTER and Head Temperature is displayed Press ENTER and XXXF degrees is displayed Press MENU fo return to the previous menu l 3 4 INFORMATION Software Version Display the software version of the fixture Press MENU to access main menu press UP DOWN until Information is displayed and press ENTER Press UP DOWN until Software Version is displayed and press ENTER and the display will show VX X software version 8 Press MENU 16 return to the previous menu 22 DESIGN WASH LED ZOOM User Manual ver 1 l www elationlighting com PERSONALITY Status Settings Address Via DMX When ON define the desired DMX address via an external controller 1 Connect the fixture to the externa
38. vement is not located in the default position after the reset This error can happen if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor or its driving IC on the main PCB is defective or fails 33 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com CLEANING AND MAINTENANCE 6 A U T O N Disconnect power before cleaning or maintenance CLEANING Frequent cleaning is recommended to insure proper function optimized light output and an extended life The frequency of cleaning depends on the environment in which the fixture operates damp smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture s optics e Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt debris accumulation e Never use alcohol solvents or ammonia based cleaners MAINTENANCE Regular inspections are recommended to insure proper function and extended life There are no user serviceable parts inside this fixture please refer all other service issues to an authorized Elation service technician Should you need any spare parts please order genuine parts from your local Elation dealer Please refer to the following points during routine inspections e A detailed electric check by an approved electrical engineer every three months to make sure the circuit contacts are in good condition and prevent overhea
39. ver 1 www elationlighting com FIXTURE MENU ON BOARD SYSTEM MENU The DESIGN WASH LED ZOOM comes with an easy to navigate system menu The next section will detail the functions of each command in the system menu LCD MENU CONTROL PANEL The DESIGN WASH LED ZOOM control panel see image below located on back of the fixture offers several features select form such as setting the DMX address running pre programmed macros changing display options and resetting the fixture to factory defaults There are 4 buttons which are explained below MENU Press this button to enter the fixture menus and to return exit to the previous menu The display will automatically exit the fixture menus in 10 seconds from the last button press UP DOWN Press these buttons to navigate through the different menu functions and access sub menu selections ENTER Press this button to select a menu item and press again to confirm your selection NOTE To access the LCD Menu Control Display via the internal battery when the fixture is not powered press either the UP or DOWN buttons The LCD Menu Control Display will shut OFF automatically about 10 seconds from the last button press DESIGN WASH ZOOM 17 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com Default Settings Shaded DMX Address Setting DMX Value Display Slave Setting Auto Program Music Control Power On Running Time Fixture
40. ware is insert in the pre arranged screw holes in the bracket of the fixture Use the original packaging and materials to transport the fixture in for service DO NOT TOUCH the housing bare hand during its operation Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving 8 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com 1 LED Assembly 2 Yoke Assembly 3 LCD Menu Control Display 4 MENU Button INN roman 5 UP Button e 6 60 OS Te AS 6 DOWN Button 7 ENTER Button 8 Microphone 9 3 Pin DMX OUT 10 3 Pin DMX IN 11 5 Pin DMX OUT 12 5 Pin DMX IN 13 Power Switch 14 Fuse Holder 15 Power Cord 9 DESIGN WASH LED ZOOM User Manual ver 1 www elationlighting com FIXTURE INSTALLATION FLAMMABLE MATERIAL WARNING Keep fixture at least 5 0 ft 1 5m away from any flammable materials decorations pyrotechnics etc ELECTRICAL CONNECTIONS A qualified electrician should be used for all electrical connections and or installations iS CAUTIONS e For added protection mount the fixture in areas outside walking paths seating areas or in areas were unauthorized personnel might reach the fixture e Ambient operating temperature range for this fixture is 5 F 113 F 15 C to 45 C Do not use the fixture under or above this temperature e Before mounting the fixtu
Download Pdf Manuals
Related Search