Table of contents
Contents
1. medicines if necessary 4 2 Attention 532nm wavelength Q switch laser should be used in the treatment ofthe brown and red pigment The 532nm wavelength laser is green light which is different from the laser with wavelength of 1064nm The hemoglobin and man made brown or red pigments absorb the laser with wavelength of 532nm Since the normal skin can also absorb it the cuticle tissue may vaporize in surface and there may be blood clots called purpura in the medical service When the brown and red pigment absorb the 532nm laser it will be demolished and pop out from body or be smashed down and expelled by metabolizing 4 2 1Side effects from the treatment of the black and blue pigments 1 Special pigments may fall off and the common pigments may precipitate since the vaporization of skin and death of cuticle 2 There may be swelling or blood clot under skin however it will recover in 20 60 days varied with individuals Low energy density small spot shall be used in the treatment of the brown or red pigment with 532nm wavelength laser Repeat the operation for several times if necessary but at least with 2 months interval 3 before starting the treatment explain to clients the possible side effect In some cases the tattoo contains iron ion which will cause the paint oxidized and make the treatment failure No washing with water and sunburn after the treatment against infection and pigment precipitation 4 Direct2. sight at 532nm wavelength laser may cause blindness All people present in the treatment room must wear protective eyewear and only the people concerned with the treatment should be allowed to access to the treatment room 4 2 2 Annex Instructions and attentions for black diamond 1 Clean face 2 Daub the whole face with black diamond 3 Aim at the treatment part by 1064nm wavelength laser Caution It is forbidden for those people who are in wound or acne Treatment frequency 5 times for a course of treatment the interval is 21 28 days 5 Configuration Main Protective Foot switch Power body glasses supply wire Power Instructions Laser output Frequency supply key head multiplier 1064nm 532nm Water filler
3. Tattoo Removal Laser Machine Operating Manual Caution Do not directly look at the hole of the laser gun otherwise the blindness will be happened Make sure the stopper must be revolved off before the water injection and then keep the water flowing normally Make sure it must be distilled water or purified water when injecting the cooling water into the machine tap water or mineral water is absolutely forbidden because it will result in water scale when heated which will cause mechanical error of the machine Make sure to check the water circulation and the joint between the machine and the hand piece before running the machine The operation should be done when everything is ready If there are any abnormal sounds please stop working immediately and lighten on again after the capacitance being charged up inside machine Make sure the machine is absolutely discharged before transportation Make sure to change the water once one month Warning The treatment handle contains delicate and fragile optical components During transportation the case shock absorbing package should be used otherwise it may cause malfunction Contents 1 Safety Items 1 1 Equipment safetyvas zn 1 2 Transporationsaleyassn tea nel 4 LESySIeHmsale riesen sehen 2 Installation amp Operation 2 lProd ct description ane ee 5 2 2 Environment condition an ann la 5 2 3 Power requirement teen Re 6 2 4 Installation and operation 240 v
4. ace of composite painting material under your skin The left pigment can be cured with green 532nm wavelength laser after 2 months interval Make the client know the situation which may happen during the course of treatment to avoid dispute caused by ignorance Better to shave the patient s eyebrow for easy operating before treatment 2 Possible situation during treatment When treating the very deep pigment tissue since the pigment would absorb laser energy in great quantity there may be burst of pigments accompanied with noisy sound The client s skin may swell for the breakage of pigments even bleed Just after the first time treatment the pigment may become very thin but it will recover in several minutes This is the regular reaction of organization It is suggested that the best time for second treatment is 2 3 months later after the first treatment Caution During the operation the eyelid board that is used for protecting the client s eyes must be used Otherwise the operation is very dangerous to the clients for the blindness caused by laser radiation cannot be cured 3 Possible situation after treatment The hair may decolorize or even fall off sometime But fresh hair will grow up in four weeks The bleeding and swelling will disappear in about one week to one months varied with individuals 4 Physician care after treatment No washing eyebrow lining with water within 3 to 7 days No sunshine Take the antibiotic
5. djust from 100mj 2000mj Temperature display and protection The system has the temperature indicating function from which the temperature of the circulating water can be checked any time When the water temperature is higher than the programmed protective temperature the excessive temperature will show on the screen with the alarming buzzer and the machine will stop working in that case when the temperature of the circulating water is lower than the enactment protection temperature the machine will run normally 4 When closing the system firstly please release the foot pedal then move away the hand piece next press the work button to quit the simmer state and then turn off the machine with the key in anticlockwise pull off the plug at last 5 Usage of the transformer with wavelength of 532nm Take off the 1064nm wavelength transformer and change with the 532nm wavelength transformer other operations are as the same Caution The light with wavelength of 532nm is harmful to your skin Please read Annex 2 before operation 2 6 Cleanness Please clean the transformer with alcoholic gauze or tampon stick before and after each treatment 3 Maintenance and troubleshooting 1 Basic maintenance e Clean the camera lens The camera lens is at the back of the laser sighting device so before or after each treatment please examine the surface of lens to see if there is any splash on it If there is please wipe the le
6. ifications Light source Q switched Nd YAG solid state laser Wavelength 1064nm 532nm 1320nm Energy level 100 2000mj Fluence lt 20mJ cm2 Pulse duration 8ns Frequency 1 10 Hz Cooling system Built in distilled water circle system Power requirement Single phase 220V 10A Size of the machine 43 X 29 X 40cm Weight 12kg Components and functions gt Vv VVVVV V Key switch general power switch to turn on the system in clockwise and to power off the machine in anticlockwise Simmer button to press down and the system come into ready for work status to press down again and the system goes back into standby status Power indicator to adjust the voltage Frequency button to adjust the speed of frequency Setting button to set the language and the system interface Foot switch port to step on the pedal for outputting laser Insurance cube port to link with 10A 5 X 20 insurance cube Power socket to exchange 110v 220v input plug with wire 2 2 Environmental conditions Normal conditions Temperature 15 C 25 C Relative humidity 70 Air pressure 860 1060hpa Power requirement single phase 110v 220vr10 10A Conducting way Continuous running with intervals at every 5 000 times pulsing 10 minute intermission is better Co
7. ite oka 2 er ere 6 2 5 Operation insttuellions an UT HER 9 2 6 Gleammessr es seen di CN qe ue 10 3 Maintenance 3 1 Basic MAME NANOS rss and retiens dresse the 11 3 2 Exception handnd u ea BEA 12 4 Accessories 4 1 Attentions for Treatment of black and blue pigment with 1064nm Q Switch TAS CT RTS ns dies ER ST SEILER IBRRE 12 l Safety Items 1 1 Equipment safety The X6 laser machine use single phase power supply of 220V and the maximum output is no more than 3A The power supply must be three wire battery outlets the spec is 10A It is dangerous to open the protective cover optionally because the high tension exists inside machine during operation even after the machine is power off some parts ofthe machine would possibly have residue pressure 1 2 Transportation safety This YAG Laser system can be moved and transported easily but since the treatment handle contains delicate and fragile optical components So during transportation the case shock absorbing package should be used otherwise it may cause malfunction 1 3 System safety For the system safety please notice the following devices Simmer button no laser can output in standby status Key switch avoid unauthorized operation 2 Installation amp Operation 2 1 System description This YAG Laser system contains optical circuit system in the treatment handle and electric circuit system computer system and cooling system in the console Spec
8. ns softly with alcoholic tampon stick e Refilling cooling water After the system running for 10 days please screw off the spillway and scupper to draw off the water Screw on the scupper after the water has been drawn off and then refill the distilled water or purified water If the water flows out from the spillway it means the tank is full and then screw on the spillway Caution the cooling water must be distilled water or purified water 2 Troubleshooting Troubleshooting Examinable parts Examine the electric circuit Examine power plug and cable No power Examine the 10A insurance cube Examine the emergency shutoff knob No laser output and buzz Examine whether the system is in simmer status when step on the pedal Examine whether the pedal switch is out of work The output of energy Examine whether the power supply is normal becomes weak or blank Examine whether the lens has been cleaned shoot happens Examine whether the cooling water is flowing in circulating 4 Accessories 4 1 Attention 1064nm wavelength Q switch laser should be used in the treatment of the black and the blue pigment 1 Preparation before treatment Make sure whether the patient s skin is keloid skin whether they have purified their eyebrows tattoo with other means Explain to clients that after the treatment there still are pigment trace left which possibly caused by sunburn or brown and red tr
9. oling system Built in distilled water circle cooling system 2 3 Power requirement Power source single phase 110v 220v 10 50hz42 10A gt Caution The power supply of this YAG Laser system must match with international standard three hole plug in order to make sure the socket well grounded gt Caution The voltage range is between 110v 220v and 240v Firm voltage device is necessary which power requirement is 800VA 2 4 Installation and operation 2 4 1 Foot switch installation e Insert the foot switch plug into the socket at the back of the case e Take off the non hole stopper and change it with the hole stopper 2 4 2 Operation The adoption of 1064nm head or 532nm head is according to the treatment e First fill the tank with distilled water or purified water by a funnel mineral water is not permitted When you add water please open the spillway and close the scupper then keeps on observing it Close the spillway when the water is full enough to outflow from the spillway e Start machine 1 Turn the key in clockwise to the ON position for simmering the system and the monitor will show as picture 1 this is the greeting interface then please press any button to enter treatment interface as picture 2 picture 2 Keystoke presentation picture 3 As we can see the screen is separated into 4 rows on the first row is working voltage of which the adjustable scope is 100 2000mj On the sec
10. ond row is operating frequency of which the adjustable scope is 1 6Hz on the third row is temperature indicator on the left and working frequency counter on the right and the counting range is 0 999999 on the fourth row is status indicator which indicates the function for each button When entered into the work platform you can press the FREQ button and VOLT button to adjust the frequency and power press the first button in the left to light up the machine when Xe light is light up successfully the keystroke state indicator will change into blank shot press working button and the state indicating area will show as OK then you can operate the foot pedal Meanwhile the system starts counting every pulse When closing the system press the working button to quit the work state press the trigger button to quit the simmer state and then turn off the machine with the key You can quit the simmer state by pressing trigger button during the treatment When you keep stepping on the foot switch all of the button will be without function Adjust the frequency Release the foot pedal press FREQ button to enter into the working frequency adjusting menu press to increase the frequency and press to decrease it Adjust the voltage Release the foot switch press VOLT button to enter into the working voltage adjusting menu press to increase the voltage and press to decrease it the step is 10V it is available to a
Download Pdf Manuals
Related Search