User Manual - Neuation.com
Contents
1. 2 f12UOCIOri 4 1 Swix Vortex Mixer PRODUCT USER MANUAL TABLE OF CONTENTS 1 Product 1 1 1 Introduction 1 2 Intended Use 1 3 Features 1 4 Technical Specifications 1 5 Accessories 2 Safety PFECAUEIONS 00 reinen 3 299 Installato anne anna es ee 4 3 1 Location 3 2 Connecting Power Adaptor 4 Standard Parts Listing ccscsccccscsscsccccscccceccccsceccscecesceccecsceess 5 5 User Interface and 6 6 Optional Attachments amp its 7 4 ODAO 11 7 1 Connecting power adaptor 7 2 Setting Speed 7 3 Standby Touch amp Continuous mode 7 4 Touch mode operation 7 5 Continuous mode operation 8 Maintenance and 15 9 Warranty Statement ccccccccccccccecccccccccccceccsssssssssssssesscseceeecs 16 10 Product DISD OS AN ids nun en 17 1 PRODUCT DESCRIPTION 1 1 INTRODUCTION Congratulations You are using the essential Vortex Mixer The product is designed for your everyday laboratory mixing needs The silent easy to use vortex comes with unparallel reliability amp safety It has a variable speed setting which allows low rpm start up for gentle s2. Removing Universal Attachment Note Do not rotate standard attachment or any attachments attached to modified shaft body g 6 ATTACHMENTS amp ITS INSTALLATION To attach the microtube or microplate foam attachment first install the universal attachment then place the foam attachment as shown in image below Ensure universal attachment is securely fixed Universal gt ANE Place the microplate microtubes first in the foam attachment amp then place the foam attachment on the universal attachment attached to vortex mixer To avoid spillage of samples match the cut out in foam with plastic extension universal attachment To attach flask first attach universal attachment then please flask on its center Fix one side of the rubber on the extended portion of universal attachment holding flash Press the center hole through the neck of flask Stretch the other end amp lock if firmly on the other end of extension of universal attachment 10 7 OPERATION 7 1CONNECTING POWER ADAPTOR amp SWITCH Always connect the power cord pin to the mains socket then turn ON the switch Before connecting to mains ensure that the vortex mixer is in STANDBY mode amp cup head attachment is firmly tighten with modified shaft body Below is the image showing the STANDBY mode of the vortex mixer OFF Rear Side Connecting Power cord to Mains Socket Standby mode 7 2 SETTINGSPEED Rotate the spee
3. business to business sphere to which this product is assigned may no longer be disposed off in municipal or domestic waste They are marked with the following symbol to indicate this As disposal regulations within the EU may vary from country to country please contact your supplier if necessary 17 om ge ge ge a sir 7 Cf Cf 2 Neuation Technologies Pvt Ltd Plot no 16 Part of 15 A GIDC Electronics Park SEZ 0 SC Kolavada Road Sector 26 29 2042 Gandhinagar Gujarat India 6 27 Ph 91 2764 248241 21 Fax 91 2764 248243 www neuation com info neuation com o ge Ae oF se 2 23 er 4 st 2 2 Zs Ze P 28 P 7 sf PA 2 ZN
4. well as any supervision required for safety If requested the products must be returned to the distributor in well packed and insured manner and all shipping charges must be paid Some states do not allow limitation on the length of implied warranties or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights This warranty is given expressly in lieu of all other warranties expressed or implied Products received without proper authorization will not be entertained All items returned for service should be sent postage prepaid in the original packaging or other suitable carton padded to avoid damage We will not be responsible for damage incurred by improper packaging All items returned for service should be set postage prepaid in the original packaging or other suitable carton added to avoid damage This warranty is valid only ifthe warranty is registered with the supplier within 30 days from the date of purchase 16 10 PRODUCT DISPOSAL Incase the product isto be disposed of the relevant legal regulations are to be observed Information on the disposal of electrical and electronic devices in the European Community The disposal of electrical devices is regulated within the European Community by national regulations based on EU Directive 2012 19 EU on waste electrical and electronic equipment WEEE According to these regulations any devices supplied after 13 06 05 in the
5. d setting knob to select speed value The maximum speed of Vortex mixer is 2800 RPM The maximum speed indication for different attachments is shown in product sticker Speed Setting knob with arrow allows to set recommended speed for specific attachments Note Ensure not to use attachments beyond indicated maximum speed 11 7 OPERATION 7 3 STANDBY TOUCH amp CONTINUOUS MODE Placingthe 3 way switch in STANDBY position will keep the vortex mixer in OFF state 1 6 it will not operate as TOUCH or CONTINUOUS mode Below is the position of 3 way switch showing the vortex mixer is in STANDBY mode It is recommended to use STANDBY mode while replacing attachments or when not in use It is recommended to use STANDBY mode while setting operation speed OFF Press the 3 way switch up towards the Touch side to enable the TOUCH mode The TOUCH mode is generally used while using standard attachment In TOUCH mode vortex action will start only when cup head is pressed Below isthe position of 3 way switch showingthe vortex mixer isin TOUCH mode TOUCH Press the 3 way switch down towards side to enable the CONTINUOUS mode In CONTINUOUS mode the vortex action start automatically without pressing cup head at set speed Below is the position of rocker switch showingthe vortex mixer in CONTINUOUS mode Note 1 CONTINUOUS mode is generally uso ith attachments 2 STANDBY mode i
6. entilation Keep the unit away from heat amp direct sunlight to avoid sample temperature issues 3 2 CONNECTING POWER ADAPTOR Power cord cable Rear Side Power cord cable is pre installed to the rear side of the unit and another side is the power cord pin which needs to connect to main supply as shown in the above figure Make sure that mains switch is not ON until cord is connected to the mains socket Note Designed for 220 240 VAC 50 Hz 4 4 STANDARD PART LISTING Cup Head Control Panel 3 Way Switch Speed setting knob with indication arrow Power cable gt Base Mount 5 USER INTERFACE amp DISPLAY Name Symbol Power Led showing the status of vortex action 1 Power LED Glowing when vortex action 15 in process Not Glowing No Vortex action Speed setting knob to set different speed 2 Speed Rotate clockwise to increase amp anticlockwise to decrease speed value Max Speed Indication for Specific Attachement Attachments position with reference to speed setting knob for Max allowed speed indication Rocker switch is use to select different mode in vortex mixer OFF stand by Continuous amp touch operation mode 3 way switch Mode selection 6 ATTACHMENTS amp ITS INSTALLATION Standard attachment cap is used for vortexing sample in individual tubes The vortex mixer can accommodate optional attachment
7. haking and high speed mixing for vigorous vortexing of samples 1 2 INTENDED USE The Vortex Mixer is a general laboratory vortex mixer It is indented for application where vortexing of single or multiple tubes is required 1 3 FEATURES Continuous amp touch operation Adjustable speed ranging upto 2800 rom Long life Brushless AC motor with ball bearing Inbuilt counter balance for steady and safe operation Orbital diameter of 4mm Broad range of Accessories optional Robust construction for stable operation Sf 755 22 20 122 Silentoperation 1 PRODUCT DESCRIPTION 1 4 TECHNICAL SPECIFICATIONS Orbital Diameter Maximum Load Capacity Different modes Protection Rating Ambient Temperature Dimensions LxBxH Weigh Power Consumption 70W 1 5 ACCESSORIES 1 Standard cup head pre installed 2 Universal attachment amp separate attachment heads for Microplate Microtubes foam amp Flask Optional 3 Product user manual amp warranty card 2 SAFETY PRECAUTIONS 1 10 11 Do not use the vortex mixer in hazardous atmosphere or with hazardous material for which the unit is not designed Always use the vortex mixer on level amp stable surface for best performance and maximum safety Do not lift vortex mixer with the attachments as every attachment including the standard attachment cup head are designed to be pulled up for interchanging Do not rotate or give full rotation to the attachme
8. low figure GF an G Universal Attachment Flexible Rubber Attachment Make sure the flask is held in place firmly By stretching the rubber attachment and fixing it with universal attachment Note The 250ml flask used with these rubber attachment can be operated with maximum speed as indicated by knob marking Care needs to be taken while attaching or filling the flask with the sample to avoid liquid spillage damage to user or unit 6 ATTACHMENTS amp ITS INSTALLATION To remove the standard attachment pull up the standard attachment with one hand as shown in below figure You can then attach the cup or universal attachment as shown below Center press the attachment as shown in below figure until it snaps Ensure that it attach firmly with modified shaft body Center Press to attach AR Standard NG s ment Modified shaft body Removing Standard Attachment Attaching Standard Attachment Note Do not rotate universal attachment or any attachments attached to modified shaft body To attach place the universal attachment on modified body shaft amp center press the attachment as shown in below figure until it snaps Ensure that it attach firmly with modified shaft body To remove the universal attachment pull up the universal attachment with both hands as shown in below figure Center Press to attach AR Universal Atachment ss 0 Modified shaft body Attaching Universal Attachment
9. nts cup head universal attachment etc attached to the modified shaft body Clean the unit with damp cloth using mild detergent only Do not use chemical cleaning agents If liquid spills on the unit first disconnect unit from external power supply and then clean the unit with adamp cloth Do not use the unit if it shows any sign of electrical or mechanical damage Don t use the accessories which are not recommended by manufacture it may affect the performance The instrument is designed be used in the laboratory environment Do not fill microtubes microplate or flask while they are attached with vortex mixer liquid spillage may harm the unit The maximum speed for each attachment is marked do not run at higher speed than those indicated 3 INSTALLATION The Vortex Mixer is supplied in a box Open the box open the inner packaging and gently take the vortex mixer out of the box Before 1st usage ensure that all the packaging is removed amp cup head is firmly tightened press down to confirm The user manual and accessories should be kept with the unit and keep all packaging in safe storage for atleast two years for warranty purpose 3 1 LOCATION Take the unit out and place it on the leveled amp stable surface near the grounded electrical outlet The surface should be clean and free from dust to ensure that the feet grip the surface firmly Keep the clearance of 10 side of the unit for proper v
10. s Optional attachment include universal attachment which combining with other foam rubber attachments can be use for mixing samples in microplate microtubes amp flask Standard Attachment Universal Attachment The below additional foam attachments combining with universal attachment can be use for mixing sample in microplate amp microtubes 1 5 2 0ml First attach the universal attachment place tubes in foam sheet amp then combine it with universal attachment 495 Universal Attachment Microtube Foam attachment Note The microtube foam attachment can be operated with maximum speed of microplate indication is Product sticker with the fill not more than 75 of sample Do not fill tubes while they are in foam attachment liquid spillage might harm the attachment or unit P P Universal Attachment Microplate Foam attachment Note The Microplate foam attachment can be operated with maximum speed of Microplate Indication in Product sticker with the fill not more than 75 of well of microplate Do not fill microplate while they are in foam attachment liquid spillage might harm the attachment or unit 6 ATTACHMENTS amp ITS INSTALLATION The below additional rubber attachments combining with universal attachment be use for mixing sample in 250ml flask First always attach the universal attachment then place flask on the universal attachment amp tighten it with rubber attachment as shown in be
11. s generally used while setting parameters or when not in use 12 7 OPERATION 7 4 TOUCH MODE OPERATION Before operating check that the upper cup head is firmly tighten to the modified shaft body Set the require speed using knob in STANDBY mode amp select the TOUCH mode using 3 way switch For touch mode operation gently press amp hold the cup head using tube as long as you want to run Release to stop operation Below is the images showing the operation in touch mode Press Down 13 7 OPERATION 7 5 CONTINUOUS MODE OPERATION Before operation keep the vortex mixer in standby mode and set required speed Check attachment you wish to use is firmly tightened with modified shaft Select the mode to start continuous mode operation In CONTINUOUS mode the vortex action start automatically without pressing cup head at set speed In continuous mode at any time user can modify speed by rotating knob For universal attachment make sure to fill the liquid or samples before placing the attachments Microtubes Foam Microplate Foam Flask rubber attachment on vortex mixer 14 8 MAINTENANCE amp CLEANING 1 The vortex mixer and its accessories should be cleaned regularly with a moist cloth 2 Ensure that while cleaning the unit is not plugged in 3 The brushless AC motor in the vortex mixer requires no routine maintenance Any required service should be performed by the authori
12. zed qualified personnel only Repairs performed by unauthorized personnel may void the warranty 4 Always keep the vortex mixer amp its accessories in the safe storage amp clean periodically with moist cloth After cleaning ensure that all parts are dried 5 Do nottry to pull the vortex mixer with attached accessories 6 Do nottryto rotate the attachments attached to modified shaft body 7 Do not use the vortex mixer amp its accessories in direct sunlight or under water 15 9 WARRANTY STATEMENT This products is warranted to be free from defects in material and workmanship for a period of two 2 years from date of purchase Your product will be duly repaired upon prompt notification in compliance with the following conditions This warranty is valid only if the product is used for its intended purpose and within the guidelines specified in this instruction manual This warranty does not cover damage caused by accident neglect misuse improper service natural forces or other causes not arising from defects in original material or workmanship This warranty does not cover any incidental or consequential damages commercial loss or any other damages from the use of this product The warranty is invalidated by any non factory modification which will immediately terminate all liabilities on us for the products or damages caused by its use The buyer and its customer shall be responsible for the product or use of products as
Download Pdf Manuals
Related Search