Car License Plate Camera (Effio WDR) SHR
Contents
1. 4 d 2 1 4 UNC D Lens Mount VIDEO VIDEO 1 VIDEO S R5485 GND Gs 24 This mount is used to install a CS mount lens CS adaptor ring is required when using a C mount lens 2 Camera Mounting Screw Holes Screw holes for mounting the camera 3 Mount Adaptor The adaptor can be attached onto the top or the bottom of the unit Auto Iris Lens Connector 4 pin type The lens connector supplies the auto iris lens not supplied with DC control signal 5 OSD Control Buttons ENTER button UP amp DOWN buttons LEFT amp RIGHT buttons PIN NO VIDEO DC 1 DC 12V CONTROL 2 NC CONTROL 3 IRIS DRIVE 4 GND DRIVE E 8 Gq 110906 XE224NF G D 0562 V1 Video Connector Video can be outputted via this connector 750 IRIS Mode Selection Switch Select DC or VIDEO mode according to the lens Video Connector Video can be outputted via this connector 750 Communication Connectors 1 RS485 2 RS485 3 Day amp Night External Input controlled by external infrared illuminator 4 Day amp Night Output 5 NC 6 Ground Power Input Indicator Light When the camera is conne2. MANUAL The manual adjustment mode enables a more precise adjustment Increase and or decrease the red and blue color values according to the color changes of the object to set the suitable color temperature RED color vale ranges from 000 to 255 BLUE color value ranges from 000 to 255 PUSH LOCK Follow the instructions on the screen Wait for a few seconds for the camera to set up When completed there will be a message displayed on the screen To find the optimal setting for the current luminance environment in this mode point the camera towards a sheet of white paper and press the ENTER button Whenever the condition changes readjust it 13 110906 XE224NF G D 0562 V1 4 5 2DNR amp 3DNR Dynamic Noise Reduction MAIN MENU 2DNR amp 3DNR LENS AUTO lt EXPOSURE SET lt WDR OFF WHITE BALANCE ATW 2DNR amp 3DNR SET DAY NIGHT AUTO IMAGE SET EFFECT SET lt SYSTEM SET lt EXIT lt 2DNR MIDLOW 3DNR MIDLOW RETURN Sub Menu under 2DNR amp 3DNR mode 1 When the noise level is reduced the camera performance can apparently be improved When recording digitally the image file size can be lessened by selecting the noise reduction As the level of gain changes the background noise in the low light level decreases automatically 2 Please use the UP and DOWN buttons to 2DNR amp 3DNR on the MAIN MENU and press the ENTER button to do furt
3. Car License Plate Camera Effio WDR SHR 728 User Manual Thanks for purchasing our product Before operating the unit please read the instructions carefully and keep this manual for future reference Safety Warning A 1 Read this manual carefully before installing the unit Please read this manual first for correct installation and operation A 2 Never install the camera on a ceiling that cannot hold its weight The product may fall down and cause damages A 3 Never install the camera near electric or magnetic fields Install the camera away from TV radio transmitter magnet electric motor transformer audio speakers since the magnetic fields generate from above devices would distort the video image A 4 Never install or use the camera in areas exposed to water oil or gas The water oil or gas may result in operation failure electric shock or fire Do not use this unit near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement near a swimming pool in an unprotected outdoor installation or any area which is classified as a wet location A 5 Never face the camera toward the sun Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit A 6 Power Cord Protection Touching the wet power cord with hands or touching the power cord with wet hands may result in electric shock Power supply cords should be routed so that they are not likely to b
4. RESTORE Select NO to exit or select YES to restore all the settings to the defualt value NOTE The following items will not be restored CAM ID PROTOCOL BAUD RATE and LANGUAGE 24 110906 XE224NF G D 0562 V1 4 10 Balun Function UTP A Balun s function is available for BOX cameras only It would normally require 3 terminals Video Power RS485 to succeed a connection However via Balun 1 is sufficient The cameras OSD can be used and controlled remotely via RS485 communication port The most important thing is transmission can still stay clear and true Road Surveillance Monitoring Center Color 1000ft 300m Video r B W 1600ft 500m le Power za ON 45 45 UTP 111VPD UTP 111VPD UTP Balun UTP Balum Data 4 11 EXIT Select EXIT to automatically save the settings made and exit the MENU MAIN MENU LENS AUTO EXPOSURE lt WDR OFF WHITE BALANCE ATW 2DNR amp 3DNR SET lt DAY NIGHT AUTO lt IMAGE lt EFFECT SET SYSTEM SET lt lt 25 110906 XE224NF G D 0562 V1
5. SEL 12 4 5 2DNR amp 3DNR DYNAMIC NOISE REDUCTION ttt ttt ttti 14 o odd uu up e M E LED Ef 15 Gta hc cect NU EE 18 E E E 20 STEM uL LL LESE DE Lc t CI 23 4 10 BA UN FUNCTION UIT Bu merenti eiit uie Mr Mm 25 QOEM A hore cue A okt Maa he tier Eie ag 25 3 110906 XE224NF G D 0562 V1 1 Introduction Built with Sony s latest Effio DSP and 1 3 960H Double speed CCD WD image sensor SHR 728 has the capability of achieving resolutions of over 700TVL the WDR function can produce clear and true image without noise even in tunnels an environment with very strong light and can capture vehicle license plate numbers at speed up to 200km hr 125mile hr during the day and 150km hr 90mile hr at night The most exciting feature is the Multi Shutter modes Scheduled Shutter Mode Manual Shutter Mode and Auto Shutter Mode SHR 728 supports Balun RS 485 remote control to control the OSD remotely When it comes to Car License Plate Camera SHR 728 is definitely ideal to install at any kind of car entrances and exits for capturing car license plates 1 1 Main Features 1 3 Hyper Wide Dynamic Car License Plate Camera Effio WDR 700TVL 0 03Lux F 1 2 Sense up 0 0001Lux gF 1 2 Capable of Capturing Car License Plate Numbers at High Speed Day up to200km hr 125mile hr Night up to150km hr 90mile hr with
6. WXYZ0123456789 96 amp X iiem t lt 1 CLR POS RETURN J lt _ f Select ft or 4 with the character selection cursor and click the ENTER button to move the cursor in the direction of the arrow CLR Select to clear one letter of the input POS Adjust the position of the camera ID 23 110906 XE224NF G D 0562 V1 COMM Select SET lt to enter sub menu for further settings 1 The CAM ID PROTOCOL and BAUD RATE will be displayed for the first five seconds on boot 2 Changes made to the CAM ID PROTOCOL and BAUD RATE will only take effect after you exit the COMM page This is to prevent the camera from unexpected disconnecting caused by remote access CAMERA ID 1 1024 DISP CAM ID OFF TOP LEFT TOP RIGHT BOTTOM LEFT BOTTOM RIGHT Select to hide the CAMERA ID or to adjust the CAM ID position BAUD RATE 2400 4800 9600 19200 38400 PROTOCOL PELCO D PELCO P NOTE The COMM function is available for models with RS485 only SYNC Only available to cameras with AC power input Use the LEFT amp RIGHT buttons to switch SYNC mode between NT Internal and L L Line Lock Set to L L and click ENTER to bring up submenu for further settings LANGUAGE Use the LEFT amp RIGHT buttons to select the language preference The options are ENGLISH ERAT FIRMWARE Please refer to the actual firmware The figure shown on above is for reference only
7. XE224NFG D 0562 V1 EXTERNAL EXTERNAL NIGHT INPUT BURST RETURN J Sub Menu under the DAY NIGHT EXTERNAL mode EXTERNAL mode allows the user to switch the DAY NIGHT mode with external signals For example you can synchronize the DAY NIGHT mode between the camera and the infrared LED illuminator For the camera with the light sensor it is suggested to set the DAY NIGHT mode to EXTERNAL to ensure the best result NIGHT INPUT Select input level LOW It will be the COLOR mode if the input signal is HIGH On the contrary it will be the B amp W mode HIGH It will be the B amp W mode if the input signal is HIGH On the contrary it will be COLOR mode HIGH 3 12V or OPEN LOW GND LOW HIGH COLOR B amp W B amp W COLOR 485 dei When th infrared ill en the external infrared illuminator is in use the camera can switch to COLOR or BN B W mode via DNI pin of the ALO communication connector GND 17 110906 XE224NF G D 0562 V1 4 7 IMAGE MAIN MENU LENS AUTO EXPOSURE SET WDR OFF WHITE BALANCE ATW amp 2DNR amp 3DNR SET DAY NIGHT AUTO IMAGE RESOLUTION MID SHARPNESS 019 SHARP SUP 010 CONTRAST 000 SATURATION HILL III 000 HUE MIHI 000 MIRROR NORMAL POS NEG OFF WHITE PIXEL COMP SE
8. 200 1 250 1 300 1 350 1 400 1 450 1 500 1 600 1 750 1 1 000 1 1 500 1 2 000 1 3 000 1 4 000 1 10 000 1 30 000 1 60 000 1 100 000 sec Automatic Gain Control 0 200 Levels Adjustable Level Settings White Balance ATW AWB PUSH LOCK MANUAL 3200K 6300K ANTI CR WDR BLC Fog Reduction WDR FOG REDUCTION BLC OFF High Light Compensation ON OFF AUTO Language Flickerless ON OFF Dynamic Noise Reduction 3D 2D Sense Up AUTO Limit x2 x512 OFF Digital Image Stabilizer ON OFF ENGLISH TRADITIONAL CHINESE SIMPLIFIED CHINESE E Zoom 1 256 Pan Tilt Adjustable Motion Detection Privacy ON OFF 24x16 Zones Alarm ON OFF 15 Zones Programmable Quadrangle Mosaic Automatic IRIS Connector VIDEO DC D4 IRIS Jack Lens Mount CS mount With Adaptor Ring Power Supply Consumption 12Vdc 24Vac 10 8 39Vdc 24Vac 2 0W Operation Storage Temp 10 C 50 C 20 C 60 C Operation Storage Humidity Maximum RH80 RH90 Dimensions 64 W x58 H x123 L mm Net Weight 350g 2 110906 XE224NF G D 0562 V1 2 Camera Overview 2 1 Dimensions M 110906 XE224NF G D 0562 V1 2 2 Description of Camera Parts
9. 485 DNI DNO ALO amp Connect the ALARM terminal here GND ALARM TIME Only available to cameras with Communication Connectors Alarm time can be set from 000 to 255 seconds PRIVACY MASK Options are ON OFF Set to ON and click ENTER to bring up submenu for further settings PRIVACY MASK AREA SEL MODE POSTION COLOR TRANSP MOSAIC RETURN lt AREA SEL There re 1 15 areas which can be masked MODE Options are ON OFF Choose ON to show the protected area on the screen OFF to hide the protected area on the screen POSITION Press ENTER button for further settings Adjust the area size and shape by dragging the vertices of the quadrilateral Push ENTER to switch the vertices in the sequence of left top right top left bottom and right bottom and push ENTER again to return to PRIVACY MASK submenu COLOR Use LEFT and RIGHT buttons to adjust the color of PRIVACY MASK The options are BLACK RED GREEN BLUE YELLOW CYAN MAGENTA and WHITE 21 110906 XE224NF G D 0562 V1 TRANSP Use LEFT and RIGHT buttons to adjust the transparency of PRIVACY MASK The options are 0 00 0 50 0 75 and 1 00 Note that the MOSAIC will be disabled when the transparency set to 1 00 MOSAIC Options are ON OFF Use LEFT and RIGHT buttons to display the block in mosaic or not DIS Digital Image S
10. 6 XE224NF G D 0562 V1 NIGHT 2 DAY When the camera detects the current light level is higher than the set value it ll switch from NIGHT mode to DAY mode Value 0 63 NOTE 1 The setting differences between DAY NIGHT and NIGHT DAY should be more than 5 or the camera will keep switching from DAY NIGHT and NIGHT DAY constantly 2 The infrared illuminator is not recommended to use under AUTO mode Please Switch to EXTERNAL mode when an infrared illuminator is installed DELAY TIME Sometimes there s only a sudden and short light level change Delay time can be set to avoid switching too fast The camera will switch the mode after the set DELAY TIME passed DELAY TIME can be set from 0 to 255 seconds BURST Turn the BURST function off to reduce the color noise under B amp W mode However not every DVR machines can receive video signals without the color burst signals If the camera cannot switch back to COLOR mode from B amp W mode please turn the BURST function on NOTE The BURST function is adjustable under B amp W EXTERNAL and SCHEDULE mode NIGHT OUTPUT GND 5V COLOR 5V GND B amp W GND 5V 485 485 DNI When the camera switches modes the external DNO lt components will be alerted via DNO pin of the ALO communication connector GND 16 110906
11. AUTO IRIS DC t LIII 050 When the DC LENS is in use push IRIS SWITCH on the control board to DC and the TYPE on the menu will be displayed as DC e When the VIDEO LENS is in use push IRIS SWITCH on the control board to VIDEO and the TYPE on the menu will be displayed as VIDEO SPEED The speed of DC Lens is in direct ratio to the number you set The range of the SPEED can be set from 000 255 NOTE The SPEED function will not work when the TYPE of LENS set to VIDEO 110906 XE224NF G D 0562 V1 4 2 EXPOSURE When the MAIN MENU is displayed on the screen use the UP and DOWN buttons to the EXPOSURE and press the ENTER button to do further setups MAIN MENU EXPOSURE LENS AUTO lt MODE AUTO IRIS EXPOSURE SET BRIGHTNESS tM O30 SHUT 1 50 S WHITE BALANCE ATW SHUT MAX E 2DNR amp 3DNR SET gt LOW LUX BRIGHT x1 0 DAY NIGHT AUTO IMAGE SET lt EFFECT SET lt SYSTEM SET lt lt AGC GAIN 150 SENSE UP OFF Main Menu Sub Menu MODE Two modes to select from AUTO IRIS and SHUT AUTO IRIS When in AUTO IRIS mode SHUT is activated and adjustable e When in SHUT AUTO IRIS mode SHUT MAX is activated and adjustable BRIGHTNESS When the EXPOSURE MENU is displayed on the screen use the UP and DOWN buttons to the BRIGHTNESS and use LEFT and RIGHT buttons to adjust the screen brightness from 000 to 255 SHUT SHUTTER SHUT MAX
12. External IR LEDs Self Defined Auto Shutter Speed Range Multi Language OSD Control Powerful 510X WDR High Light Compensation HLC 2D 3D Noise Reduction Sense Up 512x Functions Digital Image Stabilizer DIS E zoom Function 1 256x Advanced Motion Detection Function Quadrangle Mosaic Privacy Mask 1 2 Content List Car License Plate Camera EFFIO WDR SHR 728 B Users manual 1 110906 XE224NF G D 0562 V1 1 3 Specifications TV System PAL NTSC Image Sensor 1 3 Sony 960H EXview HAD CCD II Number of Total Pixels 1020 H x596 V 1020 H x508 V Resolution 700TVL Sony Effio WDR Minimum Illumination Color 0 03Lux gF 1 2 B W 0 005Lux gF 1 2 Sense up 0 0001Lux QF 1 2 Wide Dynamic Range 510x Normal Camera Video Output 1 0Vp p Composite 75O BNCx2 Signal to Noise Ratio S N More than 55dB AGC off Gamma Correction 0 45 Mechanical IR Cut Filter ICR Automatically Switches Switching Lux Level can be adjusted IR LED Working Distance Compatible with Infrared Illuminator Menu OSD Control or by RS485 Control Title TITLE LOCATION Synchronizing System INTERNAL LINE LOCK for DC AC and AC version Digital Day amp Night Mode COLOR B amp W AUTO EXT Electronic Shutter Auto Shutter Self Defined Auto Shutter Speed Range 20 Steps Programmable Manual Shutter 20 Steps 1 50 60 FL 1 120 100 1
13. SHUTTER MAX The shutter speed is in direct ratio to the number you set The range of the shutter speed can be set from 1 50 1 100 000 sec LOW LUX BRIGHT LOW LUX BRIGHTNESS Use LEFT and RIGHT buttons to adjust Low Lux Brightness The options are x0 25 0 5 X0 75 x1 0 AGC GAIN The bigger the number the brighter the screen can be Note that the noise will increase as well The AGC GAIN range can be set from 000 to 200 SENSE UP SENSE UP is used to maintain a brilliant vivid screen image by automatically detecting changes in the level of light under low light level conditions Select the desired item and press LEFT and RIGHT buttons to adjust the settings The options are x2 x4 x8 x16 x32 X64 x128 x256 x512 and OFF 9 110906 XE224NF G D 0562 V1 4 3 WDR 1 When the MAIN MENU is displayed on the screen use the UP and DOWN buttons to WDR and press the ENTER button to do further setups MAIN MENU LENS AUTO lt EXPOSURE SET lt WDR OFF The modes under the function are WDR BLC WHITE BALANCE ATWe 2DNR amp 3DNR SET lt and OFF DAY NIGHT AUTO lt IMAGE SET lt EFFECT SET lt SYSTEM SET lt EXITe 2 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings WDR Wide Dynamic Range When there are both bright and dark areas at the same time selecting this mode makes both areas distinctive WDR TU TU RETURN J Sub Menu u
14. T lt IMAGE SET lt EFFECT SET SYSTEM SET EXIT lt RETI IBN Sub Menu under the Image Function 1 Please use the UP and DOWN buttons to IMAGE on the SETUP MENU and press ENTER button to enter 2 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings RESOLUTION Options are HIGH MIDHIGH MID MIDLOW LOW and OFF SHARPNESS Level 000 015 The contour of the video image becomes cleaner and more distinguished as the level of SHARPNESS increases f the level goes up extremely it may affect the video image and cause noise SHARP SUP SHARPNESS SUPPRESION Level 000 015 Select to adjust the value of the sharpness in low Lux environment CONTRAST Level 032 031 Select to adjust the value of the contrast SATURATION Level 050 050 Select to adjust the value of the gain HUE Level 050 050 Select to adjust the value of the hue MIRROR NORMAL VERTICAL vertical rotated MIRROR horizontal rotated and ROTATE vertical and horizontal rotated POS NEG ON OFF Positive Negative Reversal Select ON or OFF to enable or disable this function 18 110906 XE224NF G D 0562 V1 WHITE PIXEL COMP WHITE PIXEL COMPENSATION Level 000 010 Select to enter the sub menu for further settings Click START to search for the white pixels of CCD and set MARKER to ON to display the pixels on the screen Decrease the THRESHOLD value to find more white pixels or i
15. TING INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE REFERENCE NOTE The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All specifications are therefore subject to change without notice 2 110906 XE224NFG D 0562 V1 Table of Contents ASIN TROD TION 25 iE De uL LC EL M Di E LII 1 MAIN EEATURES 5 2 once Gc toned oe Te aae a e cete 1 1 2 GONTENT BIST ipid tese ute cute eod ste AEE 1 1 3 SPECIFICATIONS 2 5 5 etes e pb te td eee eos ae do pe veo ed donee dace telo aie Gil o ee eo 2 2 CAMERA OVERVIEW eene duree csl hebetes ae 3 211 cach ette doeet ree e eee Deed terre ce dues ev esee uae Ee ode de vta dte eet baden Ae etr coded aoe recedes 3 2 2 DESCRIPTION OF CAMERA PARTS scseseee e eee e eere rhe rss hier sr re reser rre iret rre rre rese iren eterne 4 3 0SD OPERATION d iiacoe teen Ra tutes eunt 6 3 T OSD CONTROLE B TIONS tec etel Da Det e tere 6 9 22 05 D OBEBATION once p cer Foca hits es da pr d ci ce fs 7 4 CONFIGURATION 5 etie nite aes DLL LE dM E 8 hsc M ISLAM totu DUNS a etes 8 ZO BXROSUPBi Na AIR MEL ALIA pb LL A 9 AS VID isi uus tunt M DRE LAUR tfc iE E Ma SEES E 10 44 WHITE BALANCE ient utem SL pat
16. cted to a power supply the indicator light will be on RS 485 Terminal Impedance Switch Set the first and the last equipment terminal impedances as 1200 and set the rest parallel connection equipment in the middle as HiZ to obtain the best transmitting status Power Input Terminal Connect to the power supply 5 110906 XE224NF G D 0562 V1 3 OSD Operation 3 1 OSD Control Buttons Use this button to move the cursor upwards to the desired item RIGHT Use this button to move the cursor to the right to select or to adjust the parameters of the selected item The parameter increases when the right button is pressed 9 DOWN Use this button to move the cursor downwards to the desired item LEFT Use this button to move the cursor to the left to select or to adjust the parameters of the selected item The parameter decreases when the left button is pressed ENTER Use this button to display the main menu to confirm and to enter the submenus when they re available Items with lt symbol in the end contain sub menus For further settings of those items select the desired item with the button or v and press the ENTER button to bring up the sub menu and edit 6 110906 XE224NF G D 0562 V1 3 2 OSD Operation MAIN MENU LENS AUTO lt EXPOSURE SET lt WDR OFF WHITE BALANCE ATW amp 2DNR amp 3DNR SET DAY NIGHT AUTO IMAGE SET EFFECT SET SYSTEM SET EXIT lt 1 Start
17. e walked on or pinched by items placed upon or against them playing particular attention to cords and plugs convenience receptacles and the point where they exit from the appliance A 7 Attachments Do not use attachment not recommended by the product manufacturer as they may cause hazards Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind onto the product A 9 Do not operate the camera in environments where the temperature humidity or power source is beyond the specified ones Use the camera in suitable environments where the temperature is within 10 C 50 C and humidity below 80 Use the input power source as this instruction indicated 1 110906 XE224NF G D 0562 V1 A 10 Cleaning Unplug the unit from the outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning A 11 Never disassemble the camera nor put impurities in it Disassembly or impurities may result in trouble or fire A 12 Stop using when the product emits smoke or abnormal heat A 13 Servicing Do not attempt to repair this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel A 14 Retain Instructions THE SAFETY AND OPERA
18. her setups 3 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings 14 110906 XE224NF G D 0562 V1 4 6 DAY NIGHT The camera can be set in Color or B W mode in the Day Night function NOTE 1 EXT function is not available for OC version 2 Communication Connectors including RS485 are not available for all cameras Please refer to 2 2 for details MAIN MENU LENS AUTO EXPOSURE SET WDR OFF WHITE BALANCE ATWe 2DNR amp 3DNR SET The modes under the function are COLOR DAY NIGHT AUTOS B amp W AUTO EXTERNAL IMAGE SET lt EFFECT SET lt SYSTEM SET lt EXIT lt 1 Please use the UP and DOWN buttons to DAY NIGHT on the MAIN MENU and press the ENTER button to enter 2 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings COLOR The COLOR DAY mode B amp W The BLACK amp WHITE NIGHT mode AUTO DAY NIGHT AUTO LIVE LEVEL 063 DAY gt NIGHT 003 NIGHT gt DAY 025 DELAY TIME 005 BURST OFF NIGHT OUTPUT 5V RETURN J Sub Menu under the DAY NIGHT AUTO mode The camera will switch to DAY Color mode or NIGHT B amp W mode according to the set value LIVE LEVEL This indicates the current light level DAY 2NIGHT When the camera detects the current light level is lower than the set value it ll switch from DAY mode to NIGHT mode Value 0 63 15 11090
19. ncrease the value to reduce the number of white pixels 19 110906 XE224NF G D 0562 V1 4 8 EFFECT MAIN MENU LENS AUTO EXPOSURE SET WDR OFF WHITE BALANCE ATW amp 2DNR amp 3DNR SET DAY NIGHT AUTO IMAGE SET EFFECT SET lt SYSTEM SET EXIT lt EFFECT MOTION DET PRIVACY MASK DIS E ZOOM HLC RETURN 1 Please use the UP and DOWN buttons to EFFECT on the MAIN MENU and press ENTER button to enter 2 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings MOTION DETECTION Options are ON OFF Set to ON and click ENTER to bring up submenu for further settings MOTION DET DETECT SENSE 115 BLOCK DISP ON DETECT AREA SET MONITOR AREA SET ALARM OUT OFF ALARM TIME lt DETECT SENSE Sensitivity can be set from 0 to 127 The higher the number the more sensible the camera can be BLOCK DISP Set the block display to ON OFF DETECT AREA Press SET to enter the sub menu and set the detect area MONITOR AREA Press SET to enter the sub menu and set the detect area 20 110906 XE224NF G D 0562 V1 ALARM OUT Only available to cameras with Communication Connectors Choose ON to output the alarm connect the alarm device to the ALO of the communication port on the rear panel so that the alarm can be output Be sure to turn off all the power before connecting 485
20. nd press LEFT and RIGHT buttons to adjust the settings MAIN MENU LENS AUTO lt FXFOSURE Ele The modes under the function are ATW AWB WDR OFF ee ATW 3200K 6300K ANTI CR MANUAL and PUSH 2DNR amp 3DNR SET lt DAY NIGHT AUTO lt LOCK IMAGE SET lt SYSTEM SET lt EXIT ATW Auto Tracking White Balance This mode can be used within the color temperature range from 1800 K to 10500 K e g around fluorescent lights outdoors around sodium vapor lamps or inside tunnels AWB Auto White Balance Select this to allow the camera automatically adjust the white balance under all conditions 8200K Select this when the color temperature is around 3200 K when surrounded by sodium lights 6300K Select this when the color temperature is around 6300 K ANTI CR Color rolling suppression Select to set the white balance mode to the ANTI CR mode Follow the instructions on the screen Wait for a few seconds for the camera to set up When completed there will be a message displayed on the screen NOTE The White Balance can not fully function under the following conditions When the following occurred please select PUSH LOCK Mode When there s a higher temperature surrounded the object gt When there s darkness surrounded the object gt When there s a fluorescent light surrounded the object or where the light changes all the time 12 110906 XE224NF G D 0562 V1
21. nder WDR mode LEVEL Use the LEVEL function to adjust the brightness of the whole area Level 000 255 DARK Use the DARK function to adjust the brightness of the dark area Level 000 255 BRIGHT Use the BRIGHT function to adjust the brightness of the bright area Level 000 255 10 110906 XE224NF G D 0562 V1 BLC Back Light Compensation Even when there is a massive backlight behind the object bright images of the background and the object can still be captured by selecting the BLC mode BLC The modes under the function are AUTO and MODE AUTO AREA MANUAL LEVEL AUTO LEVEL 008 MANUAL RETURN J Sub Menu under BLC mode AUTO Set AUTO LEVEL to adjust the BLC automatically The range is 000 015 MANUAL Set AREA and MANUAL LEVEL to adjust the BLC value manually The default AREA is BOTTOM 1 3 and the default LEVEL is MID Stay with the default value the bottom 1 3 area will be the brighter area with the middle level of brightness AREA BOTTOM 1 8 TOP 2 3 BOTTOM 2 3 LEFT 2 8 and RIGHT 2 3 MANUAL LEVEL HIGH MID and LOW OFF When set as OFF there ll be no wide dynamic range 11 110906 XE224NF G D 0562 V1 4 4 WHITE BALANCE The screen color can be adjusted by using the WHITE BALANCE function 1 Please use the UP and DOWN buttons to WHITE BALANCE on the MAIN MENU and press the ENTER button to do further setups 2 Please select the desired item a
22. tabilizer Options are OFF and ON When set to ON the DIS function will help to prevent vibration and the E Zoom function will be disabled E ZOOM E ZOOM 004 000 001 RETURN J Sub Menu under the E ZOOM mode Select ON and press ENTER button to do further setups Options are RATIO 001 256 zoom in 1 to 256 times PAN 512 511 horizontal zoomed in viewing and TILT 001 256 vertical zoom in viewing HLC High Light Compensation HLC MODE OFF CLIP LEVEL 010 SCALE 010 RETURN J MODE Select to choose HLC mode from OFF ON and AUTO CLIP LEVEL Adjust the value of the HLC clip level from 000 to 255 SCALE Adjust the value of the HLC scale from 000 to 015 22 110906 XE224NF G D 0562 V1 4 9 SYSTEM 1 Please use the UP and DOWN buttons to SYSTEM on the MAIN MENU MAIN MENU SYSTEM LENS AUTO CAMERA TITLE E EXPOSURE COMM SET WDR OFF SYNC INT WHITE BALANCE ATWe ERE ENGLISH 2DNR amp 3DNR SET lt RESTORE DAY NIGHT AUTO lt IMAGE SET lt EFFECT SET lt SYSTEM SET4 lt 1 0 11 06 02 RETURN J 2 Please select the desired item and press LEFT and RIGHT buttons to adjust the settings NOTE The version of FIRMWARE shown on the above is for reference only The actual version varies by the production CAMERA TITLE CAMERA TITLE CAMERA ABCDEFGHIJKLMNOPQRSTUV
23. to operate the OSD menu Press the ENTER button to bring up the OSD main menu to start operating OSD menus 2 Select items with the cursor buttons e Use buttons 4 and v to move the cursor up and down e Use buttons 4 and gt to switch the modes or to adjust the parameters or the values of the settings 3 Switch to the sub menu Items with lt symbol in the end contain sub menus For further settings of those items select the desired item with the button 4 or v and press the ENTER button to bring up the sub menu and edit MAIN MENU AUTO IRIS LENS AUTO lt EXPOSURE SET lt WDR OFF WHITE BALANCE ATWe 2DNR amp 3DNR SETd gt DAY NIGHT AUTO lt IMAGE SET lt EFFECT SET lt SYSTEM SET lt EXIT lt DC tt 050 RETURN J Main Menu 4 Return to the previous page Select RETURN and press the ENTER button to return to the previous page 5 Exitthe OSD menu Select EXIT with the button 4 or v and press the ENTER button to exit the OSD menu 7 110906 XE224NF G D 0562 V1 4 Configuration 4 1 LENS When the MAIN MENU is displayed on the screen use the UP and DOWN buttons to the LENS and press the ENTER button to do further setups MAIN MENU AUTO lt lt LENS EXPOSURE WDR WHITE BALANCE 2DNR amp 3DNR DAY NIGHT IMAGE EFFECT SYSTEM lt TYPE OFF ATW amp SET lt AUTO lt SET lt SET lt SET lt
Download Pdf Manuals
Related Search