Senza titolo-1
Contents
1. as Sensibility 4 Sensibility 1 Sensibility 2 Sensibility 3 Operating range Max current absorption Blocks schematic TECHNICAL CHARACTERISTICS from 9 5 to 18V 70 mA Operating temperature from 20 to 90 C Averange distance to begin detection 70 80 cm Central module ECU Display Power cable RF Cable Sticking material Antenna sensor PROXEL S r l Via Val Della Torre 39 10149 TORINO ITALY Tel 39 011 296022 Fax 39 011 2218053 Technical Assistance eps proxel com2. close to the bumper 10 15 cm Note The distances will vary depending on the size of the obstacle and correspond to the central zone of the bumper on the lateral edges the distances is less see Figure 6 The alert occurs only when the vehicle is approaching an obstacle a fixed object in front of the bumper is only detected after the first movement of approach WARNING 1 In presence of rain or high moisture weather the system reduces his sensibility automatically in order to eliminate a part of false alarms that could be given by movement of water on the bumper 2 As soon as the system is activated an acknowledgement of the surrounding of the bumper is made Consequently it is very important during testing operation not to switch on the system while you are very close to the central unit and antenna sensor in order not to have false information on the working capability of the system During the test you must also take into consideration the fact that after the first approach to the bumper any subsequent APPROACH without first reset the system can give false interpretations of the functionality of the sensor due to special characteristics of the EPS DUAL 2 0 with DISPLAY software specifically created to reduce false signaling in the rainy conditions ALERT SIGNAL ALARM SIGNAL RISK OF CONTACT SIGNAL Fig 6 Central module ECU
3. ENG IROXEL PROXIM LHECTRONICS INSTALLATION INSTRUCTIONS amp USER MANUAL Rear parking sensor mod EPS DUAL 2 0 wih DISPLAY EPS DUAL 2 0 with DISPLAY can be installed only on rear bumper The sistem is strictly a driver assistance device and should not be relied upon as a A security device or a substitute for safe driving practices Use common sense when reversing and always follow recommended safe driving guidelines a The installation of the antenna sensor constituted by an aluminium adhesive ribbon must be performed to the inside of the bumper It is of some importance that the zone of application on the inside surface of the bumper corresponds to the higher part as regards the ground but also the most distant from the car body Itis not advisable to install the antenna sensor too low Correct zone STARTING PROCEDURE a Identify on the car body the zone close to the extremity of the bumper and on the side where it is present the back gear lamp a possible hole of passage toward the intern of the trunk in order to carry out the RF cable from the antenna sensor b Through the individuated passage route the RF cable inside the trunk leaving the fast on terminal outside Fig 2 Thoroughly clean with alcohol or nitro solvent be carefull not to use antiadhesive detergent the inner surface of the bumper of the zone previously identified see Fig 1 on which will be applied the antenna sensor Starting
4. ead of the harness to the earth of the reversing lamp T ADVISABLE NOT TO CONNECT TO ANY OTHER POINT OF EARTH ON THE CHASSY OF THE CAR c Insert all plug in connectors into the proper position on the Central Unit ECU as per Fig 6 Some vehicles are equipped with a metal crash protection bar insert facing the inside surface of the bumper When this metal surface is too close to the inner surface of the bumper where you have placed the antenna sensor the distance signal can be reduced To adjust the distance signaling is sufficient to change the dip switch positions see schematic on next page Take care that the sensitivity No 1 is the lowest and the number 4 is the largest The sensibility that we recommend for most cars is the No 2 We suggest to carry out tests to determine the detection range pointing out that increasing the sensibility where itis not necessary can cause more false alerts MOUNTING OF DISPLAY a Take the display cable from the back of the car to the front using the appropriate steps as edges of plastic or rubber seals Fix the display above the rearview mirror using the adhesive on the back of it b Connect the display cable to the central module by the proper connector FINAL TESTING PROCEDURE a Turn on the key insert the back gear In a fraction of secon the control unit performs a check of the functionality of the system and if everything has been done correctly the transducer emits an acou
5. from the zone where there is the RF cable start applying the adhesive aluminum tape antenna sensor practicing a good pressure to make it well adhere to the inner surface of the bumper RF Cable Antenna sensor When the antenna sensor has been attached covering the whole of the bumper from left to right the excess length is cut off Place a piece of the included sticking material at either ends of the antenna sensor to ensure a secure fixing onto the bumper surface It is recommended but not essential to cover the antenna with a black anti rust protection paint of the same type that is applied to the underneath of a car chassis or similar to protect from the elements do not use silicon paste Sticking material Antenna sensor Connect the RF Cable coming from the ECU to the antenna sensor Apply a piece of sticking material on the connection and fix iton the bumper by a strong pressure If the ambient temperature is below 10 C we recommend heating both the mastic and the sticking area on the bumper It isnecessary to use the same material to fix the opposite extremity of the antenna Fig 5 Replace the bumper and pull the RF Cable inside the luggage compartment or engine compartment in order not to leave excess cable outside Sticking material RF Cable Fig 5 ELECTRICAL CONNECTIONS a Connect the red lead of the power cable to the positive cable that feeds the reversing lamp b Connect the black l
6. stic sound of OK two notes in rapid succession Once you have this signal the system becomes operational Possible problems and their solutions 1 Ifthe acoustic transducer does not emit any signal check all the connections 2 If the transducer emits an audible warning signal consisting of 2 notes one high and one low repeated 3 times check the connection of RF cable b Starting from about 1 meter away from the center of the bumper slowly approach both hands to simulate a parking maneuver At a distance of about 60 70 cm will be heard the first acoustic signals whose repetition rate will increase atthe decreasing distance to become a fast intermittent sound fast and then a contnuous higher frequency sound at about 10 15 cm from the bumper WARNING For a correct simulation be carefull to reset the system every time you approach c If the system shows to work regularly it is possible to fix definitely the bumper Note EPS DUAL 2 0 starts to give the signaling only when the vehicle is being approached to the obstacle a fixed object in front of the bumper for instance the hauls hook and a bull bar or the sides walls of a car box is not signaled and it is not bothered the normal operation of the device USER MANUAL OPERATING PRINCIPLE EPS DUAL 2 0 with DISPLAY is an innovative parking sensor that uses low energy electromagnetic waves and is able to detect the approach of any kind of obstacle The activation of the device isob
7. teined by the insertion of the back gear or by pressing the activation button if installed on front bumper and confirmed by a signal of OK Once activated the EPS DUAL 2 0 generates around the bumper on which is installed a protection zone Fig 6 When any obstacle present in the protection zone tends to approach the bumper you will hear a series of beeps WORKING EXAMPLE a As soon as the EPS DUAL 2 0 with DISPLAY is activated the control functionality of the system is carried out in a fraction os second In case of anomalies the speaker emits an audible warning signal consisting of 2 notes one high and one low repeated 3 times If this happens check the antenna connection to the ECU If the control is OK you hear a signal of two notes in rapid succession to confirm the proper functioning of the system If installed on the front bumper the OK signal consists of a single note b When approaching an obstacle the system activates the acoustic signal at a distance between the bumper and obstacle measured in the central area of the bumper of about 60 70 cm with 3 types of sounds 1 an increase in sequence of BIP alert informs the driver that an obstacle is approaching 2 intermittent sounds of fast repetition rate when the obstacle comes close to the bumper at a distance between 15 and 30 cm measured on the middle of bumper alarm 3 continuous sound at a more acute frequency risk of contact when an obstacle is very
Download Pdf Manuals
Related Search