Product Manual - OPTOCORE GmbH
Contents
1. 16 outputs or 8 inputs and 8 outputs can be assembled for the X6R according to the customer s requirements The microphone inputs include a high quality microphone preamp phantom power and selectable gains in 1 dB steps from 4 dB to 66 dB at a maximum input level of 22 dBu The line inputs are equipped with selectable maximum channel levels of 27 dBu 22 dBu 18 dBu 8 dBu and the line output with a selectable maximum channel level of 22 dBu 18 dBu 12 dBu 8 dBu The high quality preamps A D and D A converters make the X6R units ideal for the incorporation into audio systems even if no OPTOCORE network is present They provide a wide dynamic range with negligible distortion and extremely low noise X6R V3R TP 11 27 rev 2 4 OPTOCORE When using the X6R V3R TP as a SANE Network device the two AES EBU ports can be configured as inputs or outputs in groups of four and the AES EBU channels can be exchanged between SANE and the I O cards Word Clock input and output connections enable the synchronisation of the units to an external source and are used to pass the word clock from one unit to the next For stand alone applications the devices are equipped with an internal word clock generator Up to 8 TP devices can be used in one SANE CAT5 daisy chain to extend OPTOCORE FX fiber node with up to 64 audio inputs and 64 audio outputs and additional 100Mbit LAN ports Microphone preamps on the TP device can be controlled from any node in the fib2. OPTOCORE S Operating Manual for OPTOCORE X6R V3R TP Devices A D and D A Converter with SANE and Ethernet Copyright 2015 All rights reserved OPTOCORE GmbH Lohenstr 8 82166 Munich Gr felfing Germany X6R V3R TP A D D A Converter with SANE and Ethernet Operating Manual Rev 2 4 Page intentionally left blank OPTOCORE Important Safety Instructions Please read this manual carefully Please keep this operating manual in a safe place Heed all warnings Follow all instructions This device may only be used in accordance to the information provided in this operating manual Ensure that all recommendations detailed in this operating manual especially the safety recommendations are followed before and during use of the device Do not use this device near water and liquids for example in humid or damp rooms Clean only with a dry cloth Do not block or cover any ventilation openings Install the device in accordance with the operating manual Do not install or place the device near a source of heat Such as radiators power amplifiers or any other heat emitting devices Protect the power cord from being stepped on crushed pinched or damaged in any other way or form Pay special attention to the condition of the AC mains sockets on the device Do not place this device on an unstable table tripod cart etc The device may fall causing serious damage to the device The device can be disconnected from th
3. or even better one of them to an uninterrupted power supply UPS The power supply units operate with mains voltage of 100 240 V and frequency of 50 60 Hz Thus the device can be used throughout the world without any modifications or transformers Important The switched mode power supplies operate at very high voltages Coming into contact with the power supplies can lead to considerable electric shock which may result in death To prevent electric shock do not remove any covers of the device X6R V3R TP 16 27 rev 2 4 OPTOCORE Control All system and device parameters are set using OPTOCORE CONTROL software on a PC If the X6R V3R TP units are connected to a FX Device using SANE or DD32R E using the BI B as shown in Connection Tables the control and audio data is transmitted over SANE resp the D Sub 25 interfaces OPTOCORE CONTROL can control all X6R V3R units in a network In stand alone applications the RS232 LAN or USB port enables the configuration and monitoring of one unit attached directly to the PC Please note Please refer to the Optocore Quick Start Guide for the basic system configuration and setup For more detailed setup please refer to the Optocore Software Manual X6R TP with DD32R E X6R TP devices can work in converter mode and can be fully controlled through the Optocore network when connected to DD32R FX or DD32E device The control of the microphone preamps levels etc is enabled
4. by choosing an X6R with the appropriate card configuration in the local settings dialog of the DD32R E under Port setup Up to four X6R and eight V3R units can be connected to one DD32E using BI B Tri A or Tri B cables The I O configuration of each DD32R E port depends on the card configuration of the attached X6R device Cards Device 1 0 2 x MIC IN X6R 16Micln 16 In 2 x LINE IN X6R 16Lineln 16 In 2 x LINE OUT X6R 16LineOut 16 Out 1x E ug 1x X6R 8Micln 8Lineln 16 In 1x eoe Tx X6R 8Micln 8LineOut 8 8 Reverse TR NEO LN TX X6R 8Lineln 8LineOut 8 8 Reverse 1 x DUAL MIC X6R 8DualMic 16 In If 8 8 reverse is chosen physical channels 1 4 audio channels 1 8 of the D Sub 25 ports on the DD32R E are outputs physical channels 5 8 audio channels 9 16 are inputs The X6R AES ports are configured as eight inputs first followed by eight outputs Therefore by using the straight through BI B cable and choosing 8 8 Reverse the inputs and outputs of the DD32R E and X6R are connected correctly X6R V3R TP in SANE Network Applications X6R V3R TP devices can be connected in a SANE daisy chain and integrated with the Optocore network through any R series FX device All device parameters like gain phantom and pad can be accessed and modified using OPTOCORE CONTROL software which runs on PC connected via USB or RS232 to any FX device or via LAN to any LAN or SANE port Third Party Control Third party protocols for
5. from the port with valid incoming data with Port A having the highest priority and transmit the Preamp Control Port B can be used to re transmit the incoming signals if required Port B configuration depends on the hardware setup of the analogue I O boards in the device Word Clock Devices with Optocore SANE modules are equipped with an internal high quality low jitter clock generator as well as Word Clock inputs and outputs Any device on the network can act as the master of the network and pass Word Clock to networked Optocore SANE devices The internal networked Word Clock is available at the Word Clock output connector of each device on the network to synchronize non networked devices In standalone network configurations external synchronization is not required The Word Clock input termination can be switched on using the OPTOCORE CONTROL software s Local Settings External termination is not required to avoid cable reflections Word Clock master negotiation after any Word Clock source failure is done automatically Power Supply The device is optionally equipped with two power inputs and power supply units If one power supply fails due to malfunction of the feeding power line or the power supply unit itself the device will automatically switch over to the other power supply unit In order to make the power supply redundant both power inputs must be connected to the mains supply if possible to different phases power supply systems
6. repair work has been carried out X6R V3R TP 6 27 rev 2 4 OPTOCORE CE FCC Conformity This document confirms that the X6R V3R TP bearing the CE Communaut Europ enne label meets all requirements in the EMC directive 2004 108 EG laid down by the Member States Council for adjustment of legal requirements Furthermore the product complies with the rules and regulations of the low voltage directive 2006 95 EG and the Restriction of Hazardous Substances Recast Directive 2011 65 EU RoHS 2 This product bearing the CE label complies with the following standards ratified by CENELEC Comit Europ en de Normalisation Electrotechnique Electromagnetic compatibility Product family standard for audio video audio visual and entertainment lighting control apparatus for professional use EN 55103 1 Emission EN 55103 2 Immunity EN 60065 Safety requirements FCC notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment
7. rnit n nnns 18 Connectors and Cables RR EEEn EEEa 19 O 19 AES POS e 19 AS2I2 COMEN aR 19 Connector Hood Quality acciona o ita AA 19 USB COnNMECtiON ii ac AS Acad ee Lc LL tienes 19 Bw Lerner 19 Word Clock Connection seeeseesseeseseesseeeeee enne nenne nnn nn nen en nnnnn tenen tns ri renes tns rn tenen teste rere n nennen 19 LET BT Connection iii a a a a as 19 Hardware Connection RR 20 Example diia A a ala blade adi take 20 Exampleil no eit ee eae at 21 Connection Tables iuris Ai 22 BB Cables E 23 Technical Specifications tio aiii a li ci dai as 24 Dimensions and Weight in s E A A E 25 X6R V3R TP 9 27 rev 2 4 OPTOCORE Warranty and EBERT ida ia aida 26 SMUG Contencioso olle eed 27 Company OO A id 27 X6R V3R TP 10 27 rev 2 4 OPTOCORE Device Description Congratulations on your purchase of an X6R V3R TP A D and D A Converter Device with SANE and Ethernet The X6R V3R TP series manual will quickly demonstrate the advantages of the device and help to ease your day to day workload in a professional audio visual environment 9 in 1 the X6R V3R TP is a network converter unit for SANE with the highest degree of flexibility with regards to the I O configuration Four different card types enable the complete customis
8. standard shipment does not contain printed copy of User Manual All latest OPTOCORE user manuals can be downloaded from the website http www optocore com index php support downloads Printed version of User Manual is available on a special demand Please contact support optocore com if printed version is required Company Information Mailing Address OPTOCORE GmbH Lohenstr 78 D 82166 Munich Gr felfing Germany Telephone 49 0 89 8999640 Facsimile 49 0 89 89996455 Internet www optocore com Email Inqui optocore com X6R V3R TP 27 27 rev 2 4
9. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communication Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at his own expense Changes or modifications not expressly approved by Optocore GmbH could void the user s authority to operate this equipment Industry Canada Compliance Statement This Class A digital device complies with Canadian ICES 003 Avis de conformit la r glementation d Industrie Canada Cet appareil num rique de la class A est conforme la norme NMB 003 du Canada The authorised declaration and compatibility certification lies with the manufacturer and can be viewed on request Responsible as manufacturer is OPTOCORE GmbH Lohenstr 8 82166 Munich Gr felfing Germany represented by Marc Brunke Managing Director N B The awarding of the CE label confirms the compliance with legal directives issued for the manufacturer and marketing of electronic and electrical devices As such the CE label is not a seal of quality but rather proof that the device bearing the CE label conforms with the electromagnetic compatibility standards laid down in the above named testing regulations Munich 11 12 2013 More Kyle Marc Brunke X6R V3R TP 7 27 rev 2 4 Page intentionally left b
10. X6R available on request LINE IN LINE OUT PEAK LEVEL SIGNAL Master LED LINK 1 LED LINK 2 LED Device ID Display HEALTH LED PWR 1 LED PWR 2 LED X6R V3R TP Card in slot A and B 8 AES EBU channels 16 audio card I O switchable in groups of four 8 channel microphone input card 8 AES EBU inputs with sample rate converter 16 channel microphone input card with 8 microphone inputs and two independent preamps each 8 channel line input card 8 channel line output card Red Overflow input level exceeds max input level of OdBFS Yellow Warning level input level exceeds 10dBFS Green Signal present 2 60dBFS brightness controlled Indicates the master unit Communication is established via SANE 1 rear panel Communication is established via SANE 2 rear panel Indicates the identification number of the device Green Power supply is correctly working temperature is below the limit Power supply 1 is working correctly Power supply 2 is working correctly 13 27 rev 2 4 OPTTOCORE USB plug and LED RS232 plug LAN LINK S1 S2 LAN POWER MUTE 10 Sample rate LED X6R V3R TP USB connection for remote control via PC Green Indicates data activity D Sub 9 RS232 connection for remote control and update via PC Ethernet communication is established via SANE 1 rear panel Ethernet communication is established via SANE 2 rear panel Ethernet communication is established vi
11. a LAN rear panel Mic Card Phantom Power Output Card Mute Yellow 44 1 48 88 2 96 176 4 192 kHz 14 27 rev 2 4 OPTOCORE Rear Panel X6R TP with Analogue Input and Output Cards AES EBU PORT B OUT Jo AES EBU PORTA SANE 1 SANE2 o 0 amp 0 AES EBU PORT B WORDCLOCK Ezz OUT POWER 1 100 240V 40VA 50 60H emen AES EBU PORT A SANE SANE2 0 AES Port A and B Word Clock IN Word Clock OUT POWER 2 POWER 1 Labels GROUP SANE 1 SANE 2 LAN X6R V3R TP 2 x 8 AES data channels plus two control data channels BNC Word clock input allowing synchronization of SANE devices network from an external word clock source available on request BNC Word clock output for synchronization of external devices Mains input for power supply 2 100 240 V Mains input for power supply 1 100 240 V I O card type in the slot s and serial number Cards with Euroblock Phoenix connectors 8 channels in slot GROUP A and GROUP B at a X6R TP or in slot GROUP A only at a V3R TP SANE RJ 45 interface for data transmission 100 Mbit Ethernet SANE RJ 45 interface for data transmissi
12. ation of the I O cards It enables the conversion of analogue signals 16 inputs 16 outputs 8 inputs and 8 outputs dual microphone inputs with dual independent adjustable gains The X6R V3R TP is designed for sample rates up to 192 kHz Six different versions of X6R and tree V3R are available X6R TP 16MI 16 microphone inputs two 8 channel mic line input boards V3R TP 8MI 8 microphone inputs single 8 channel mic line input board X6R TP 16LI 16 line inputs two 8 channel line input boards V3R TP 8LI 8line inputs single 8 channel line input board X6R TP 16LO 16 line outputs two 8 channel line output boards V3R TP 8LO gt 8 line outputs single 8 channel line output board X6R TP 8MI 8LO 8 microphone inputs and 8 line outputs single 8 channel mic line input board and single 8 channel line output board X6R TP 8LI 8LO 8 line inputs and 8 line outputs single 8 channel line input board and single 8 channel line output board X6R TP 8DualMic 8 microphone inputs with two independent preamps each single 8 channel dual mic line input board What do the product names refer to V3 refers to the channel capacity of the device Where V is the Roman 5 543 8 X6 refers to the channel capacity of the device Where X is the Roman 10 10 6 16 R refers to the Optocore Revolution series hardware platform TP specifies that the device is equipped with SANE twisted pair connectivity The X6R V3R TP units can
13. be carried out without prior notification e Transport and Shipping Always ensure careful handling of the device The device should be transported and shipped in shock absorbing transport cases If these are not available we recommend well padded packaging such as the coated carton in which the device was delivered We strongly advise against the use of light weight flight cases without shock absorbing rack in rack mounting e Environments This device can be used in E1 E2 E3 E4 or E5 environments as listed below according to the harmonised European standards EN55103 1 and EN55103 2 Electromagnetic compatibility Product family standard for audio video and audio visual and entertainment lighting control apparatus for professional use E1 Residental E2 Commercial and light industrial E3 Urban outdoors E4 Controlled EMC environment e g broadcast and TV studio E5 Heavy industry The product is intended for the use in moderate climate e Ventilation Do not block or cover any ventilation openings Install the device in accordance with the operating manual Allow for sufficient space around the units at least 200 mm 7 87 free space behind the rear panel of the device and make sure to allow for air circulation near the ventilation openings on both sides of the device Keep the rear of the rack open during operation Do not operate the device close to heat emitting equipment such as power amplifiers Leave sufficient space m
14. be used together to create SANE CAT5 Network 64 audio channels Ethernet Audio channels and Ethernet can be exchanged between SANE and the OPTOCORE OPTICAL DIGITAL NETWORK SYSTEM X6R V3R TP device can be connected to any FX R series Optocore unit All parameters on the converters can be controlled and monitored with the same software application as all other Optocore devices OPTOCORE CONTROL software Every channel from TP device connected by SANE is available throughout the complete OPTOCORE fiber network The X6R V3R TP is especially designed for rack mounted applications and permanent installation All cards are equipped with Euroblock Phoenix connectors These common installation interfaces provide a simple and cost efficient connection with other audio equipment The X6R TP with the dual microphone input card removes the problem where only one of the FOH or Monitor engineers can have full gain control of a single microphone input channel Every microphone input incorporates two independent microphone preamps meaning both can be adjusted individually Therefore analogue split boxes with two stage racks to give FOH and monitor engineers the freedom to adjust their mic preamps directly at their own console can be a thing of the past The X6R V3R TP with analogue mic input line input and line output cards allow customised I O configuration per device Two one card slots can be equipped with different cards so six combinations with 16 inputs
15. device controlling can be used It is possible to control Optocore preamps directly from Yamaha Studer Soundcraft SSL Lawo and Digico consoles with Special Emulation Mode configured A Multiple Emulation Mode feature enables to control preamps in Optocore network from four different consoles X6R V3R TP 17 27 rev 2 4 OT TOCOTSE SANE bandwidth allocation The standard bandwidth allocation of a SANE link is as follows Audio 64 Channels 48 KHz Ethernet 100 MBit Fast Ethernet X6R V3R TP 18 27 rev 2 4 OPTOCORE Connectors and Cables SANE Ports Use standard fully wired twisted pair cable Cat 5 Cat 5e Cat 6 terminated with RJ 45 connectors SANE utilizes all four pairs of the Cat 5 cable two pairs for standard Ethernet transmission and two pairs for the SANE synchronous audio transport A SANE cable shall not exceed a total cable distance of 100 m AES Ports According to the RS422 RS485 hardware standard used for the transport of AES EBU standards each channel requires a twisted pair A common braided shield should enclose the pairs Standard computer data cables are sufficient for good quality AES data transmissions over the short distances typically necessary in most applications RS232 Connection Use a standard shielded RS232 cable Connector Hood Quality Locking screws for D Sub connectors should be compatible with 4 40 UNC Care should be taken in selecting the right type of connector hoo
16. ds in order to fulfil the requirements of EMl radiation directives Full metal connector hoods should be used approved acc to VDE 0871 FCC 20780 and EMC directive 2004 108 EG providing attenuation gt 40 dB between 30 MHz up to 1 GHz The shield of the cable should have contact to the connector hood USB Connection Use a USB A to USB B cable between the PC and the Optocore device LAN Connection Use a standard twisted pair cable Cat 5 Cat 6 with RJ 45 connectors Word Clock Connection Use 75 Q coaxial cable with BNC connectors Mains Connection Standard power cords with IEC C13 connectors X6R V3R TP 19 27 rev 2 4 OPTOCORE Hardware Connection Example 1 The X6R V3R TP can be used as a SANE to Optocore converter The X6R V3R FX with analog I O cards is connected with three X6R TPs with different types of cards and one V3R TP by CAT5 cables The word clock is transmitted by SANE and Optocore so there is no need to use additional 75 Q cables The following figure demonstrates the configuration of a 32 inputs and 16 returns SANE system which can be combined with a bigger Optocore ring In this example there are three Optocore X6R TP units one with two mic input cards second one works as a dual mic device third X6R TP with one input and one output analogue card There is also one V3R TP with one output card All those devices are creating a CAT5 SANE network The X6R FX device is used as a bridge between SANE and Optocore netwo
17. e level Output 2 1 Vop Zero level Referring to GND 1 7V Sense level Input 2 400 mV Remote Control Convention RS232 ElA TIA 232 57 600 Baud USB USB 2 0 Device 12 Mbit s LAN IEEE 802 3 10 100 Mbit s SANE LAN Convention Audio TIA 568A B Optocore 200 Mbit s LAN TIA 568A B IEEE 802 3 10 100 Mbit s Power supply Type Mains voltage Frequency Power consumption Security classification Security regulations Mains connector Cooling Switch mode universal input 100 240 V 50 60 Hz Depending on device 32VA Max Class 1 basic insulation connected to the protective grounding conductor Harmonised European standard EN60065 acc to IEC 950 Passive via surface and ventilation slits on both sides X6R V3R TP 24 27 rev 2 4 OP TOCORE Dimensions and Weight Front panel width 483 mm 19 inch height 44 mm 1 73 inch depth 200 mm 7 87 inch Rear panel width 438 mm 17 25 inch Weight 2 7 kg 4 41 lbs Please note Modifications that serve the purpose of technical improvement may be carried out without prior notification X6R V3R TP 25 27 rev 2 4 OPTTOCORE Warranty and Liability Summary of Warranty OPTOCORE X6R V3R TP device is warranted against defects in material and workmanship for 60 months 5 years from the date of purchase This warranty does not include mechanical damages caused by misuse This warranty covers the original registered
18. e power supply by unplugging the power cord The power cords must be freely accessible at all times The device should be disconnected during lightning storms or when the device is unused for a long period of time The device must be grounded Disconnecting the ground is strictly prohibited The internal components of the switched mode power supplies operate at very high voltages Coming into contact with the power supplies can lead to considerable electric shock which may result in death Only use attachments and accessories that are specified by the manufacturer of the device This device contains no user serviceable parts Please consult with authorised service personnel before attempting to carry out any repair or modification of the device Your warranty will be voided if you tamper with the internal components of the device X6R V3R TP 3 27 rev 2 4 OPTTOCORE Purchaser Information e Operating Manual Please read this manual If you call for technical support we will assume that you have already done so Study the operating manual carefully in order to familiarise yourself with the device and its operation The operating manual contains important information on proper use of the device It cannot be guaranteed that this operating manual will not contain typographical mistakes or misprints The operating manual is regularly revised and updated Modifications which serve the purpose of technical improvement of the device may
19. er network as well as from the console running Emulation Mode X6R V3R TP units can be set to work as high quality standalone analog to AES EBU converter in this case SANE connectivity is deactivated Up to four X6R V3R TP which are set as standalone converters can be connected to the four principle D Sub ports of one DD32R E enabling the exchange of 32 AES EBU signals 64 channels and control data The ports include two control data channels The X6R V3R TP units can be operated and controlled via the OPTOCORE network with OPTOCORE CONTROL software without the need for any external data cable For control in stand alone applications LAN USB or RS232 ports on the front rear panels can be used as well All Optocore devices are designed and built using the latest programmable microprocessors and FPGA field programmable gate array logic circuitry This allows the devices internal logic to be updated in the field ensuring a continual state of the art device Optocore devices and complete networks are configured and operated using the OPTOCORE CONTROL software The software provides access to all configuration parameters and controls needed to operate the system including naming channels setting gains and phantom power routing as well as recall and capture of partial or full system configurations The software can be operated offline as well as online with level meters for all channels on the network The LEDs on the front panel of t
20. es to OPTOCORE or your distributor dealer For a full warranty conditions refer to the Warranty Card attached to every Optocore device with a first shipment How to Obtain Warranty Service When discovering a problem with an OPTOCORE device you should contact either Optocore directly or a dealer distributor to determine and confirm a hardware fault If it is a software issue the hardware must not be returned to OPTOCORE OPTOCORE will issue a support ticket in this case If hardware service is required within the warranty period take the equipment along with warranty card to the nearest authorised OPTOCORE dealer distributor The dealer distributor will make sure that the device is serviced according to the terms of warranty by OPTOCORE or an authorised service centre If the equipment needs to be returned directly to OPTOCORE first contact support optocore com OPTOCORE requires the serial number of the equipment intended for return as well as a short description of the problem If possible you should also provide us a phone number where you can be reached during regular working hours To return a defective product please contact your distributor dealer Our web site http www optocore com provides a complete list of Optocore distributors dealers Make sure the equipment being returned is packed carefully to protect it from damage during shipment OPTOCORE requires that shipments are pre paid and insured unless specifically auth
21. ever spill liquid of any kind on the device X6R V3R TP 5 27 rev 2 4 OT TOCOTSE e Cables and Accessories Only use attachments that are specified by the manufacturer of the device Use high quality properly terminated cables to connect the device The device should only be used with optical fibre cables that are specified for use with the devices optical transceivers and within the specified power budget of the optical transceivers When not in use ensure that the optical connectors on the device and the optical fibre cables are covered with the provided caps Do not place this device on an unstable table tripod cart etc The device may fall which can cause injury and serious damage to the device Any mounting of the device should follow the manufacturers instructions and should use mounting accessories recommended by the manufacturer of the device e Servicing Do not attempt to service this device yourself The device contains no user serviceable parts components or controls The operation of an opened device is not permitted Such operation can lead to damage of the device s components due to lack of air flow through the device The device may not be serviced altered or modified without authorisation from Optocore or an Optocore authorised distributor dealer Only qualified service personnel may carry out repair and maintenance work on the device The warranty of the device will be voided if any unauthorized maintenance or
22. he X6R V3R TP units allow an instant overview regarding the status of each channel indicating if audio is present on a channel if a peak level is reached and the activation of the phantom power per channel Card Types Four types of cards with Euroblock Phoenix connectors can be incorporated into the card slots e 8 microphone inputs e 8line inputs e 8 line outputs e 8microphone inputs with two independent preamps each The X6R V3R TP is shipped preconfigured with I O cards according to the order placed with Optocore 1 The additional AES EBU and AES SRC cards for X6R TP are available upon request Please contact inquiry optocore com for details X6R V3R TP 12 27 rev 2 4 OPTOCORE Front Panel X6R TP e OPTOCORE 123456874 123456748 00000000 mx 00000000 00000000 ww 00000000 00000000 sicna 00000000 00000000 TNF 00000000 AUDIO NETWORK SYSTEM CONVERTER MODULE OPTOCORE Y Word Clock LED 5678 0000 EL 0000 0000 wr 0000 AUDIO NETWORK SYSTEM CONVERTER MODULE Indicates the selected word clock source INT Internal word clock BNC External via BNC Input DSUB External via DSUB available on request AES External via AES available on request SANE External via SANE Card and Signal Monitor for the 2 x 8 Channels 1 x 8 Channels for V3R Aand B AES only X6R available on request MIC IN SRC DUAL only
23. inimum Y RU between the device and any heat emitting devices housed in the same rack An X6R V3R device may be placed on top or beneath other Optocore products except DD32E without additional space Please note Do not populate more than 4 adjacent rack spaces with Optocore devices Maintain 1RU of empty space between each 4 RU of Optocore devices Keep the equipment rack open during operation Ensure air circulation around the devices Maintain at least 200mm 8 clearance behind the rear panel of the devices Water and Moisture etc To prevent fire or shock hazard do not expose the device to direct sunlight dust water or rain during operation or storage X6R V3R TP 4 27 rev 2 4 OPTOCORE e Cleaning Only use a dry linen cloth to clean the device If the unit is very dirty moisten a cloth using a little water and a small amount of household detergent Never use cleansing agents containing solvents to clean the device e Operating and Storage Temperature Operating temperature 20 C 50 C 4 F 122 F ensure proper ventilation Storage temperature 20 C 60 C 4 F 140 F Power Supply The device can be disconnected from the power supply by unplugging the power cord The power cords must be freely accessible at all times The device should be disconnected during lightning storms or when the device is unused for a long period of time Important The switched mode power supplies operate a
24. lank OPTOCORE X6R V3R TP A D and D A Converter for SANE Table of Contents Important Safety Instructions oomonncnnnnnicinncnnnccnnoncnnn cnc norc nn ancora 3 Purchaser oO 4 GCE Comfonmity sv id 7 Device DescriPliOmrrria ia 11 Card TYPES eresio oa 12 Front Panel Em 13 XG RTP eid E a hei le I EE E 13 VOR TP io 13 Rear Panel a ee eee ee ee 15 X6R TP with Analogue Input and Output Cards 15 V3R TP or X6R TP with Dual MicrOphON6 ococccooccccnnoncnononncnononcncnanon cnn nono nennen nennen nere nnne nnne rennen 15 BIU ADIACUI SEE M 16 SANE PONS ud ice decada 16 A Diand D A Converter dins 16 Analog INpuls e S 16 Analog OUIpUls n unt sat cao een pL rE ar a A cd restet eu Da ett edle 16 AES PONS ciat nuam UA EA m ULebusi uU i A EI A ane 16 Word Glock inen aces Se occ E etait Ei mH E T Li E E 16 POW MSU DIY 16 COMMON e PP 17 X6R TP with DDS2R E coocooncccnoncconcccnoncnononconcononcnonn cnn rca nnne nennen nnns nt nnse tns n reset rere reset neret nns en nennen nennen 17 X6R V3R TP in SANE Network Applications oooocinncnnnnnninnncnncccnoccconcnconancnnnccnnn ccoo cnn nnnm 17 Third Party Gero E E 17 SANE bandwidth allocation eene nennen nent in tnnne trennen nnne ntn en
25. on 100 Mbit Ethernet 100 Mbit RJ 45 Ethernet interface 15 27 rev 2 4 OPTTOCORE Device Details SANE Ports All TP units are equipped with two RJ45 200MBit SANE Ports for 64 bi directional channels of synchronous audio 100MBit Ethernet A D and D A Converter 24 bit converters supporting sample rates of 44 1 48 88 2 96 176 4 192 kHz ensure the high quality conversion of analogue audio signals Analog Inputs The microphone inputs include preamps with selectable gain between 4 dB to 66 dB in analogue 1 dB steps Phantom Power 48V can be activated individually on each input The maximum input level is 22 dBu It is possible to use microphone inputs for line level sources The line inputs gain controls can be individually adjusted in four steps of maximum input level 27 dBu 22 dBu 18 dBu and 8 dBu Analog Outputs The outputs gain controls can be individually adjusted in four steps of maximum output level 22 dBu 18 dBu 12 dBu and 8 dBu AES Ports According to the AES EBU standard each physical channel contains two audio channels i e with the eight digital channels on one AES Port 16 audio channels are available All X6R V3R TP units are equipped with two AES 8 channel Ports labelled A and B The ports are software adjustable for different tasks and can function as a digital split if required Both ports can operate in parallel In converter mode the X6R V3R TP will automatically take its AES EBU signals
26. orized in advance We strongly advise not to use simple flight cases without rack in rack mounting Declaration of Liability Optocore accepts no liability for damage caused to other devices through operation of the X6R V3R TP device Optocore is not liable for any damage caused by shipping accidents misuse abuse operation with incorrect AC voltage operation with faulty peripheral equipment or improper or careless installation of the device Neither OPTOCORE nor anyone involved in the production of the equipment shall be liable for any indirect special disciplinary consequential or incidental damages arising out of the use or inability to use this equipment even if OPTOCORE has been advised of the possibility of such damages In no event shall the liability of OPTOCORE exceed the purchase price of any defective equipment Optocore accepts no claims for compensation whatsoever e g cancellation of events X6R V3R TP 26 27 rev 2 4 OP TOCORE Shipping Contents The standard shipment of a X6R V3R TP unit contains the following 1 X6R V3R TP unit 1 CAT5 patch cable e 2 power cables according to the number of PSU units installed Any additionally purchased equipment such as optical wave guide cables in required lengths D Sub cables and adapters RS232 cables and international electric cables which have been supplied on your request and your purchase order cannot be listed above Please note that due to the Ecology reason
27. ps Single and Dual 4 5kQ 4 dB to 66 dB 1 dB steps Maximum input level 4 dB Gain 22 dBu 66 dB Gain 48 dBu SNR 4 dB Gain 122 5 dB A 66 dB Gain 81 5 dB A THD N 1dBFS 4 dB Gain lt 102 dB 40 dB Gain lt 100 dB Analog Audio Line Inputs ADC Impedance Gain steps 10kQ 9 4 0 10dB 4 steps Maximum input level 9 dB Gain 27 dBu 10 dB Gain 8 dBu SNR 9 dB Gain 127 5 dB A 10 dB Gain 108 dB A THD N 1dBFS 9 dB Gain lt 102 dB 10 dB Gain lt 102 dB Analog Audio Line Outputs DAC Impedance Gain steps 220 4 0 6 10dB 4 steps Maximum output level 4 dB Gain 22 dBu 10 dB Gain 8 dBu SNR 4 dB Gain 123 dB A 10 dB Gain 108 dB A THD N 0dBFS 4 dB Gain lt 100 dB 10 dB Gain lt 103 dB Reference OdBFS 18dBu Input Output Termination 150R 300R Sample Rate S 48kHz Specs noticed as typical if not otherwise stated AES Ports Convention EIA TIA 422 Channels AES EBU 2x8 Audio channels 2x16 Data rate Depending on selected sample rate Up to 30 Mbit s per channel Impedance Termination 120 O switchable 96 kQ Source lt 10 O Multi drop feature Drive level Output 2 2 Vop Zero level Referring to GND 1 7V Sense level Input 2 400 mV CM voltage at bus terminals Referring to GND 7V 412V Word clock Hardware standard BNC 75 Q Data rate Depending on selected sample rate Up to 192 kHz Impedance Output lt 50 Input 750 Driv
28. purchaser only and is not transferable This warranty does not apply to devices which have been purchased in used condition or demonstrator equipment OPTOCORE will at its discretion repair or replace a defective product providing that the defect has occurred under normal operating conditions This warranty does not cover damage from acts of God accident abuse neglect contamination unauthorised modification misuse or operation outside of the environmental specifications for the product improper site preparation or maintenance or abnormal conditions of handling This would include over voltage failures and conditions outside of the products specified ratings problems with customer supplied software or interfacing or normal wear and tear of mechanical components OPTOCORE will acknowledge the evaluation of warranty after inspection Not covered by this warranty are defects arising from electromagnetic or electrical interferences deficiency excess or surge of electrical supply air conditioning or humidity This also includes repairs made necessary by dirt abrasion moisture rust corrosion or similar conditions Devices on which the Serial Number has been removed or defaced are not eligible for warranty service OPTOCORE devices contain no user serviceable components refer to qualified service personnel for repair or upgrade The warranty will be void if you tamper with internal components Please address any questions or inquiri
29. rk 8 ANALOG INPUTS 17 24 J gL ANALOG INPUTS ANALO 25 32 16 ANALOG INPUTS G OUTPUTS 1 16 9 16 ANALOG OUTPUTS 1 8 X6R TP 16MI X6R TP 8DualMic V3R TP 8LO X6R TP8LI 8LO AES AES PORTA PORTB SANE1 SANE2 AES AES AES AES AES AES PORTA PORTB SANE SANE2 PORTA PORTB SANE1 SANE2 rm C DS T lt a A A ANALOG INPUTS ANALOG OUTPUTS SANE2 SANE 1 33 40 17 24 X6R FX 8MI 8LO WORD CLOCK OPTOCORE IN OUT LINK 1 LINK 2 Fiber links to the Optocore network Fig 1 Connection of three X6R TP units one V3R TP and one X6R FX Each of the devices in this example is an analogue converter with SANE network interface It is possible to use AES ports which are built in each TP device to input or output additional digital audio channels to from the network The configuration of the AES ports as inputs and or outputs and the routing is carried out with OPTOCORE CONTROL It is possible to route input channels from other devices in an Optocore ring to the TP outputs The same single CAT5 connection transports audio data word clock and 100 Mbit Ethernet X6R V3R TP 20 27 rev 2 4 OPTOCORE Example 2 X6R V3R TP devices are used mostly as a channel extension to main fibre optic Optocore network nodes In this example two FX devices are connected with dual ring redundant network X6R V3R TP devices are used as an analogue extension On the one end three TP device
30. s extend the channel count of X6R FX unit This group of devices can be used as a stage box with 40 microphone inputs and 16 line outputs Furthermore distance between each device can be 100m so each device can be located in a different place of the stage On the other end of the fiber loop DD2FR FX with two MADI ports is extended by two TP devices MADI ports can be connected to 3 party consoles With OPTOCORE CONTROL software Emulation Mode can be set therefore consoles may control gains for all OPTOCORE mic preamps directly without additional control unit i 46 ANALOG INPUTS ANALOG OUTPUTS 16 ANALOG INPUTS 1 16 ANALOG INPUTS ANALOG OUTPUTS 33 40 E X6R FX 16MI X6R TP 16Ml X6R TP 8MI 8LO V3R TP 8LO LINK 1 LINK 2 OUT IN OUT IN SANE 1 SANE 2 SANE 1 SANE 2 SANE 1 SANE 2 SANE 1 IN OUT IN OUT SANE 1 LINK 1 LINK 2 WORD DD2FR FX X6R TP 16MI X6R TP 16LO CLOCK MADI 1 MADI 2 ANALOG INPUTS ANALOG OUTPUTS OUT IN OUT IN OUT 1 16 ee a mM gsi Fig 2 Connection of four X6R TP units one V3R TP one X6R FX and one DD2FR FX Optocore network shown above is also capable to transport 100Mbit Ethernet without any additional equipment as well as control data e g RS485 RS422 Each X6R V3R TP device is equipped with two AES EBU ports which can be used as a additional digital I O All setup routing configuration should be performed with OPTOCORE CONTROL software OPTOCORE network in this configura
31. t very high voltages Coming into contact with the power supplies can lead to considerable electric shock which may result in death Never disconnect the main plug by pulling the cable always pull the plug itself Power supply cords should be routed in such a way that they are not likely to be walked on crushed pinched or damaged in any other way Pay special attention to the plugs and the sockets of the device Important A damaged power cable must be replaced immediately The device must be grounded Disconnecting the ground is strictly prohibited Ensure that the device is always grounded using the power connector Do not cover the ground connection of the power connector with any kind of insulation material Fuse There is no fuse in the device The power supplies contain circuitry that protects the device from overload e Lightning For additional protection of this device during lightning storms or when it is left unattended and unused for a long period of time disconnect the power cord This will prevent damage to the device due to lightning and power line surges Disconnection from the mains power supply is only possible by disconnecting the power plug from the mains socket e External objects and or liquids Never push objects of any kind into the device through openings in the casing They may come into contact with dangerous voltage points or short out parts that could result in a fire or electric shock N
32. tion example requires no additional cabling for WORD CLOCK Sync signals are transported simultaneously with OPTOCORE SANE signal X6R V3R TP 21 27 rev 2 4 OPTOCORE Connection Tables Balanced Mic Line Inputs Line Outputs Control 7 13 14 Locking system acc to 4 40 UNC ineraly bridged Use standard RS232 cable male 5VS GND female to connect to PC Locking system acc to 4 40 UNC USB Port USB Channel GND VBUS D D USB device connector rm Pte es SANE Synchronous Audio and Ethernet MAD In MAD Out In Out A device compatible with 10 100MB Fast Ethernet can be connected to a SANE port for Ethernet data communication TIT L H X6R V3R TP 22127 rev 2 4 OPTOCORE BI B Cable In order to connect a principal port of a DD32R E to an AES port of an X6R converter device a BI B cable with D Sub 25 connectors should be used DD32R E Principal Port X6R V3R AES Port A X1 X8 8 AES EBU channels X1 X8 8 AES EBU channels X9 X10 Control channels X9 X10 Control channels D Sub 25 male D Sub 25 male Fastening system 4 40 UNC Fastening system 4 40 UNC X Twisted pairs Also GND Pins 10 12 23 25 GND Shield X6R V3R TP 23 27 rev 2 4 OPTTOCORE Technical Specifications Analog Audio Mic Inputs ADC Impedance Gain ste
Download Pdf Manuals
Related Search