Use and Care Manual
Contents
1. 7 Connect all of your devices to the generator 8 Turn EcoMode switch to On This will reduce the output to a level where the generator will only produce enough power for the connected devices The reduction of extra unused power saves fuel Energizer 20 4 3 Shutting Off Your Generator 1 Disconnect all devices from the generator 2 Turn EcoMode switch to Off Let generator run with EcoMode off for 2 minutes 3 Turn Power switch to Off 4 Close the fuel valve by turning it to Off Sf To stop the engine in an emergency turn the engine switch OFF Always connect the ground terminal at the front panel to the ground earth to prevent electrical shock 21 eZVseries 4 4 Using an EZV series generator with your Devices After starting your generator you can connect your devices to it Before starting make sure that you know what you are able to power with your Generator Here s how you can find out Add the watt ratings of all the loads that the generator set will be powering at the same time Make sure that total wattage will not exceed the generator rating For example A generator set rated 5000W can power two 1500W heaters a 900W circular saw a 500W drill and a 100W light at the same time 4500W combined However to operate a second 900W saw it will be necessary to dis2. Energizer EZV SERIES USER GUIDE The engine exhaust from this product contains chemicals known to cause cancer birth defects or other reproductive harm 2015 Energizer Energizer and certain graphic designs are trademarks of Energizer Brands LLC and related subsidiaries and are used under license by Midland Power Inc EZV_UG_EN_2015 06 25 Thanks for choosing the EZV Series You re excited to power up so we ll keep this brief Let s get started THIS PRODUCT MEETS ALL CERTIFICATION REQUIREMENTS FROM SEPA OZ WE VE GOT YOU COVERED Contact us by phone at 1 877 528 3772 email us at support energizergenerators com or visit us online at www energizergenerators com SAVE THESE INSTRUCTIONS This user guide contains important instructions for your product that should be followed during installation and mainteneance of the generator and batteries This user guide covers the safety operation and maintenance procedures for the EZV2200 and EZV2800 All information in this publication is based on the latest product information available at the time of print Visit www energizergenerators com for user guide updates and operation notices No part of this publication may be reproduced without written permission WARRANTY INFORMATION YOU CAN REGISTER EASILY USING OUR ONLINE FORM www energizergenerators com See Chapter 9 for more information Product registration will allow you to request wa
3. fluid can burn eyes and clothing Be extremely careful to avoid any contact If injured wash the affected area immediately with large amounts of water and seek medical attention immediately When charging a large capacity battery or totally discharged battery excessive current may force the DC breaker to turn off In this case use a battery charger 23 eZVseries Chapter 5 Maintaining Your EZV series Generator Proper maintenance ensures safe economical and trouble free operation Improper maintenance may cause the generator to malfunction and can lead to serious injuries Contact Energizer Power Customer Support if you have any maintenance questions 5 1 Maintenance Schedule Every Every Every Every Item Task Daily 20 50 100 300 Hours Hours Hours Hours Inspection Inspect Oil Level Engine Lubricants Replace Air Filter Inspection amp Cleaning Spark Plug Replacement Valve Inspection amp Clearance Adjusting Combustion Inspection amp Chamber Adjusting Fuel Tank and Cleanin Strainer 9 Fuel Line Every two months replace if necessary Exposed TER Metal Parts Lubricate with oil After every use and especially before storage For first use of the generator Le oe Energizer 24 5 2 General Inspection Tips Look for fuel leaks around the fuel tank fuel hose and fuel valve Close the fuel valve and repair leaks immediately Look and listen for exhaust leaks while the engine is runnin
4. obstructed by debris Clean according to user manual instructions on page 25 Disconnect load before starting Incorrect oil being used Please refer to the oil usage chart on page 26 in your user s manual Faulty spark plug replace with equal or greater quality plug Refer to page 31 in your user s manual for a complete list of spark plug compatibility codes Adjust choke lever according to user manual instructions on page 20 Incorrect oil being used Use oil according to oil usage chart in user manual on page 26 Air filter element obstructed by debris Clean according to user manual instructions on page 25 29 eZVseries Generator does not produce power Generator does not produce power cont Generator outputs unstable power Generator overheats Energizer No indicator lights or display on front panel Overload indicator light keeps flashing No DC output Connected device does not operate consistently Device will not start up Engine idle unusually high or low Operation is normal when generator is cool overheating occurs within moments of start up Generator circuit breaker off or tripped Remove all loads reset breaker and check device for defects Do not exceed generator rating Adjust choke lever according to instructions on page 20 When a connected device draws high startup power the overload and output indicator light may briefly iluminate but this is to be ex
5. s manual ENergizer 38 Warranty Registration Instructions Ownership must be registered with Energizer Power Equipment in order to ensure continued warranty and service support Please fill out the registration card below and mail it along with a copy of your receipt and the original UPC barcode from your product packaging The store date of purchase and product purchase should be clearly visible on the receipt copy YOU MAY ALSO REGISTER ONLINE BY VISITING OUR WEBSITE www energizergenerators com If you wish you can confirm your registration by calling customer service at or by email at support energizergenerators com Please allow one week for mail delivery and processing PLEASE MAIL ALL ITEMS TO Midland Power Inc Product Registration 376 Magnetic Drive Toronto ON 204 Canada r Existing Owner Information First Name Last Name Company Street Name and Number City Postal Zip Code Province State Phone Number Other Contact Number Fax Number Email Product Information Model Name Serial Number Initial Date of Purchase Warranty Expiration Add 2 years to initial date of purchase 4 39 eZVseries Energizer 40 Ownership and Warranty Transfer Instructions Changes in ownership must be registered with Energizer Power Equipment in order to ensure continued warranty and service support Warranty support cannot be pro
6. 2 Operating Your Generator Before using generator a ground wire must be connected to the ground terminal The Ground terminal is located on the Front Panel Before using the ground terminal consult a qualified electrician 1 Disconnect all devices from the generator 2 Open the fuel valve turn the fuel valve from off to on Make sure the valve is turned all the way on 85 2 3 Turn choke to closed position Leave the choke in the Open position if the generator is still warm from recent use or if the air temperature is higher than 50 F 10 C 4 Turn Power switch to On Make sure EcoMode switch is set to Off 19 eZVseries SS EZV2800 only for EZV2200 proceed to step 5b Turn Power switch to Start for 5 seconds to start engine engine charges the battery If the engine does not start the battery may be dead proceed to step 5b to start the engine Running the ay ee Se ee 5b Pull Recoil handle until engine starts Several pulls may be required until engine starts Do not release the pull cord at the end of a pull this will damage the recoil assembly Bring the pull handle back down to the unit by hand 6 Once the generator has started wait at least 30 seconds for it to warm up and then you may slowly open the choke lever until it is fully open
7. ZA Yar Ove YOLVINOAY SOVLION OL Tanvd nous L NAISOMOTIAA ov E A BOVLIOA HOLIMS ANONOO3 ATSWASSY YILYJANI gt NaaHOIMOTISA Wi yov a Wet NOW TS FOZ SIM LHM Owzw va lt ror eZVseries 33 Chapter 9 Learn About your Warranty Energizer Power Equipment Customer Support Center Toll Free 1 877 528 3772 E mail support energizergenerators com Online www energizergenerators com ENERGIZER POWER EQUIPMENT PRODUCTS ARE DISTRIBUTED BY Midland Power Inc 376 Magnetic Drive Toronto ON 2C4 Canada This product is warranted to be free of defects in material and workmanship for two years from date of purchase This warranty guarantees that any defective parts will be repaired or replaced at no cost including diagnosis and replacement parts LIMITED WARRANTY PERIODS Recreational and Residential use Two Years Limited e 1 Year Parts and Labor e 2 Year Parts only Commercial use 6 months limited parts and labor This limited warranty begins at the initial time of retail purchase and covers manufacturer s defects caused by a defect in components or workmanship during the three 3 Year period The warranty coverage is continual from the initial date of purchase and does not restart at anytime under any circumstances This limited warranty
8. autions to make sure you stay safe 1 1 Safety while Operating Your Generator Always perform an oil fuel and air filter check before starting the engine Properly clean and maintain the equipment Operate the generator according to instructions for safe and dependable service Before operating the generator read the user guide carefully Otherwise it may result in personal injuries or equipment damage Never run the generator in an enclosed area to avoid harm from exhaust emissions of a poisonous carbon monoxide gas The engine exhaust from this product contains chemicals known to cause cancer birth defects or other reproductive harm Be careful not to touch the exhaust system compressor pump or discharge tubing during operation due to risk of burns Pay attention to the warning labels The engine exhaust system will become heated during operation and remain hot immediately after the engine is stopped Gasoline is a highly flammable and explosive liquid Refuel in a well ventilated area with the engine stopped This portable generator is not for use with gasoline ethanol blends with over 15 ethanol When refueling the generator keep it away from cigarettes open flames smoke and or sparks Place the generator at least 3 feet away from buildings or other equipment during operation Run the generator on a level surface Tilting the generator may result in fuel spills Know how to stop the generator quickly and understand operat
9. by unscrewing the screw at the top and releasing the panel 2 Connect the Battery locate and connect the loose connectors from the battery wiring harness and the main wiring harness The battery is now connected to the unit 3 Re install the Battery Access Panel onto the unit Ensure the screw is fastened properly 4 Remove the main engine access panel from the unit by unscrewing the 4 screws at the top and middle of the unit 17 eZVseries Energizer 5 Locate unscrew and remove the Oil Dipstick exposing the internal engine compartment Be sure not to allow any dust or debris near the engine during this time 6 Pour in the full contents of the 450 mL oil bottle provided with your unit or fill to the full mark located on the dipstick 7 Re install the Oil Dipstick and fasten tightly Wipe away any excess oil For best results drain and refill the engine oil after the first 20 hrs of use and every 50 hrs thereafter Do not remove the Oil Dipstick when the engine is warm from prior use 8 Re install the Engine Access Panel onto the unit ensur ing that all 4 screws are fastened properly 9 Remove the fuel cap exposing the fuel tank Be sure not to allow any dust or debris near the engine during this time Pour 91 octane unleaded gasoline into fuel tank add Ethanol Shield to fuel tank as directed on bottle and replace the fuel cap 18 4
10. cluding diagnosis parts and labor Your emission control system may include such parts as the carburetor or fuel injection system the ignition system and catalytic converter Also included may be hoses connectors and other emission related assemblies 37 eZVseries EMISSION CONTROL SYSTEM WARRANTY PARTS Systems Covered in Parts Description Warranty Carburetor assembly includes starting enrichment system Fuel Metering Engine temperature sensor Engine control module Fuel regulator Intake manifold Fuel Tank Fuel Cap Fuel Hoses Vapor Hoses Carbon Canister Canister Mounting Brackets Fuel Strainer Fuel Evaporative cock Fuel Pump Fuel Hose Joint Canister Purge Hose Joint Air Induction Air filter housing Air filter element Flywheel magneto Ignition pulse generator ni Crankshaft position sensor Power coil Ignition coil gnition assembly Ignition control module Spark plug cap Spark plug Crankcase Emission Crankcase breather tube Oil filler Control Tubing fittings seals gaskets and clamps associated Miscellaneous Parts with these listed systems Note This list applies to parts supplied by Midland Power Inc and does not cover parts supplied by the equipment manufacturer Please see the original equipment manufacturer s emissions warranty for non Midland Power Inc parts Consumable parts are covered up to a maximum of 30 days See the Maintenance Schedule in the owner
11. connect one of the 1500W heaters 1 Turn off all devices before connecting them to your generator Power Off 2 Insert the plug of the device into your generator based on its voltage requirements Your EZV series generator includes two 120V AC outlets one 5V USB outlet and one 12V DC outlet for charging automotive batteries See Section 4 5 before using the DC outlet 3 You can now turn your devices on and use them Power On 4 5 Using an EZV series generator to Charge Automotive Batteries You can use 12V 8 3A DC output to charge automotive batteries Be sure to monitor the battery charge time Overcharging may cause explosion injury and damage to the generator ENergizer 22 1 Connect the positive red terminal of the battery to the red positive terminal the 12V 8 3A DC Output Terminal on the front panel of your generator 2 Connect the negative black terminal of the battery to the black negative terminal the 12V 8 3A DC output terminal on the front panel of your generator Do not reverse the polarity of these connec tions 3 Insert the DC plug into the DC receptacle The generator should be running and with EcoMode off After insertion EcoMode may be turned on An explosive hydrogen gas is discharged through vent holes in the battery during charging Do not allow sparks or open flames around the generator or battery during the charging process Electrolyte
12. crews Air Filter Cover 15 eZVseries Chapter 4 Using Your EZV series Generator DANGER CARBON MONOXIDE Using a generator indoors WILL KILL YOU IN MINUTES Generator exhaust contains high levels of carbon monoxide CO a poisonous gas you cannot see or smell If you can smell the generator exhaust you are breathing CO Even if you can not smell the exhaust you could be breathing CO NEVER use a generator inside a home garage crawlspace or other partly enclosed area deadly levels of carbon monoxide can build up in these areas Using a fan or opening windows and doors will NOT supply enough fresh air ONLY use a generator outdoors and far away from open windows doors and vents These openings can pull in generator exhaust Even when you use a generator correctly CO may leak into the home ALWAYS use a CO alarm in your home If you start to feel sick dizzy or weak after the generator has been running move to fresh air RIGHT AWAY and seek medical attention You could have carbon monoxide poisoning ENergizer 16 4 1 Initial Setup of Your Generator We know you re excited to get using your generator Please be sure to follow the setup operation and shut off instructions below thoroughly to ensure the best lifespan for your generator Steps 1 3 are for the EZV2800 only If you have an EZV2200 start on Step 4 or 1 Setup the Battery Remove the Battery Access Panel from the unit
13. e product was not intended unauthorized service or any other misuse neglect incorporation or use of unsuitable attachments or parts Damage to voltage regulators caused by failure to ground shorting or overloading will not be covered under this warranty Under this Warranty we do not have the obligation to bear any transportation fees of any product to from an authorized Warranty Center Unauthorized alteration installation or any cause other than defects in material or workmanship of the product will not be covered under the warranty EXCLUSIONS NOT COVERED BY THIS LIMITED WARRANTY 1 Normal engine alternator wear 2 Damage caused by lack of maintenance as described in the Energizer User Guides or negligence by using improper or impure motor oil coolant or fuel Damage caused by accidents improper installation or storage Damage caused by water ingestion submersion or external water damage Damage or non performance caused by operation of the generator set in a marine application 6 Damage caused by operation with improper fuel or at speeds loads conditions or modifications contrary to published specifications 35 eZVseries Items not supplied by Energizer including but not limited to starting batteries battery cables external wiring fuel lines filters etc refer to exclusions 8 Repairs made during the warranty period without first obtaining a case number from Energizer Batteries supplied with any ge
14. equipment that switches all conductors other than the equipment grounding conductor The frame of the generator shall be connected to an approved grounding electrode For power outages permanently installed stationary generators are better suited for providing backup power to the home Even a properly connected portable generator can become overloaded This may result in overheating or stressing the generator components possibly leading to a generator failure 1 3 Safety while Maintaining Your Generator After any maintenance is performed wash immediately using soap and clean water because repeated exposure to lubricant may cause skin irritation 9 eZVseries e Do not clean the filter element with flammable liquids like gasoline because an explosion may occur e Turn off the engine before performing any maintenance Otherwise it can cause severe personal injury or death e Allow the generator set to cool down before performing any maintenance e Always wear safety glasses when cleaning the generator set with air e Do not clean the generator set with a pressure washer because it can cause damage to the generator set e Before working with batteries ventilate the area wear safety glasses do not smoke and always disconnect the negative cable first and reconnect it last e Use rubber gloves when coming into contact with engine oil e Always stop the generator set before removing the oil filler cap e Only qualified maintenance per
15. g Have all the leaks repaired before continuing operation Check for dirt and debris and clean as necessary Check the engine oil level and add oil as necessary Do not use gasoline or low flash point solvents for cleaning They are flammable and could explode under certain conditions 5 3 Cleaning The Air Filter Using gasoline or other flammable solvents can cause a fire or explosion Do not operate this product without an air filter PD Unscrew and remove the engine access panel Unscrew and remove the air filter assembly Remove the foam filter If the foam element is dirty clean it in warm soapy water rinse and allow it to dry thoroughly or clean in non flammable solvent and allow to dry Dip the foam element in clean engine oil then squeeze out all excess oil The engine will smoke when started if too much oil is left in the filter Wipe dirt from the air filter unit and cover using a moist rag 25 eZVseries 5 4 Changing the Engine Oil Used motor oil can cause skin irritations if left in long term contact with skin Wash hands thoroughly with soap and water after handling oil Do not dispose of used oil in drains or soil Local service shops provide environmentally friendly disposal methods 1 Stop the engine and remove the oil access panel Place a pan beside the generator Remove the oil drain screw and using the oil drainage spout found in your tool kit allow the oil to completely d
16. he storage area is free of excess humidity and dust 2 Drain the fuel tank and the carburetor 3 prevent corrosion coat screws and exposed metal with antirust oil at least twice per year Draining the Fuel Tank 1 Turn OFF the engine Remove the fuel cap 1 Turn OFF the engine Remove the fuel cap and the debris screen underneath the fuel cap 2 Empty the fuel tank into an approved gasoline container using a siphon Energizer 28 6 0 Troubleshooting Common issues can be fixed by following the instructions in this guide If the unit will not function after following these instructions contact technical support before attempting to use or repair the product PROBLEM SYMPTOMS Generator will Generator will not start not start High resistance when pulling recoil starter Difficulty Engine requires starting many attempts to start Thick smoke Exhaust fumes released from thick and dark exhaust CORRECTION The power switch is in the Off position Switch to On The engine is out of gasoline add more Engine choke is in wrong position Adjust choke lever according to instructions on page 20 Faulty spark plug replace with equal or greater quality plug Refer to page 31 in your user s manual for a complete list of spark plug compatibility codes Insufficient oil add more oil Clogged fuel line inspect gas tank for debris The engine does not have enough oil add oil Air filter element
17. ing it Remove the oil filler cap and examine the oil level If the oil level is at or below the minimum oil level refill the oil to the maximum oil level mark Reinsert the oil filler cap and tighten securely Maximum Oil Level Minimum Oil Level Engine oil is a major factor affecting engine performance and service life Non detergent or vegetable oils are not recommended ENergIZer 14 Gasoline substitutes are not recommended They may be harmful to the fuel system components Gasoline is highly flammable and explosive under certain conditions Refuel in a well ventilated area with the engine stopped Do not smoke or allow open flames or sparks in the area where the generator is being refueled or where gasoline is stored Do not overfill the tank Be careful not to spill fuel when refueling Wipe up any spilled gasoline and let the area dry before starting the engine 3 2 Check the Air Filter 1 Unscrew and remove the engine access panel Remove the air filter element and observe for cleanliness 2 Clean the air filter element with soap and water or solvent Squeeze dry and then soak in clean engine oil 3 Squeeze out all excess oil and reinstall Replace the filter if it is damaged Check the air filter using the maintenance schedule Always inspect air filter before using the generator Clean Air Filter every 3 months or after 50hrs of operation according to Section 5 3 Cleaning the Air Filter S
18. ion of all the controls Never permit anyone to operate the generator without proper instructions Keep children pets and machinery with rotating parts away during ENergizer 8 operation Do not operate the generator in rain or snow Do not allow any moisture to come in contact with the generator Do not touch the spark plug while the engine is operating or shortly after the engine has been shut down 1 2 Understanding AC Safety Before connecting the generator to an electrical device or power cord Make sure that everything is in proper working order Faulty devices or power cords can lead to an electrical shock Turn off the generator immediately if the device begins to operate abnormally Then disconnect the device and investigate the problem Make sure that the electrical rating of the device does not exceed that of the generator If the power level of the device is between the maximum output power and the running power of the generator the generator should not be used for more than 30 minutes WARNING Connections for standby power to a building s electrical system must be done by a qualified electrician and must comply with all applicable laws and electrical codes National Electrical Code NFPA 70 Improper connections may cause serious injuries to electrical workers during a power outage and when the utility power is restored the generator may explode or cause fires The generator shall be connected through transfer
19. is valid for residential or recreational applications only and only when the generator receives all necessary preventative maintenance as described in the Energizer Generators User Guide The repair or replacement of a generator will take place within a reason able period of time during normal business hours All repair and replacement parts shall be warranted for 90 days after the initial date of installation or purchase ENergizer 34 LIMITATION OF REMEDIES AND DISCLAIMERS Midland International Inc disclaims any responsibility for loss of time or use of the generator in a recreational vehicle or any vehicle in which the generator is installed transportation commercial loss or any other incidental or consequential damage Any implied warranties are limited to the duration of this written warranty THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE OF AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OF ANY OTHER WARRANTY WHETHER EXPRESS OR IMPLIED Consumable parts such as oil or fuel filters fuel cut off valve brushes fuel injection nozzle valve lubricant or ignition plug are not covered under this warranty All expenses incurred in maintaining and replacing parts for generator shall fall on the purchaser This warranty coverage does not include parts affected by accident and or collision corrosion or rust normal wear incorrect fuel type or fuel contamination use in an application for which th
20. l Recoil Starter Handle Battery Access Panel Rubber Feet 11 eZVseries USB Output Overload Low Oil Outlet Light Light Light On Off Ignition Switch AC Dual 7 Outlet DC Reset 20A Circuit Breaker DC Outlet EcoMode G d Switch raun 120V 30A EcoMode Output Overload Low Oil Outlet Switch Light Light Light On Off Ignition AC Dual Switch Outlet DC Reset 20A Circuit Breaker DC Outlet 30A Circuit Breaker USB Outlet Ground ENergIZer 12 2D Part Name Quantity EZV series Generator DC Charging Cables 450mL 10W30 Oil with Funnel Make sure your generator set has everything in the table above 13 eZVseries Chapter 3 Setting Up your EZV series Generator Setup should be done every time you start up your generator these quick checks will ensure you get the most out of your generator Exhaust gas contains poisonous carbon monoxide Never run the generator in an enclosed area Be sure to provide adequate ventilation Operate the generator on a level surface If the generator is tilted fuel spillage may result Keep away from moving parts while the generator is running The generator is air cooled and may be damaged if ventilation is inadequate 3 1 Checking the Engine Oil Level 1 2 3 4 Ensure the generator is on a level surface Inspect engine oil Take out the oil filler cap and clean the dipstick Check the oil level by reinserting the oil filler cap without rotat
21. nerator product should be considered a bonus item and not covered by warranty Batteries can be damaged by shock shorting terminals heat acid spillage and a number of other factors that cannot be controlled after they have left our facility It is the customer s responsibility to take great care when handling a battery so no spillage of acid will occur and cause corrosion damage caused by battery acid is not covered under this warranty Warranty Claim Procedure Warranty service must be performed by of our authorized service dealers If you feel your generator is malfunctioning due to a defect or misuse simply contact our customer support center for technical advice a warranty claim or general information Warranty service operation assistance and product support is provided by Energizer Contact us at the following numbers PRODUCT REGISTRATION Product registration is required for product support and warranty coverage The owner s registration found in the user manual can be completed and mailed You can also register Online at www energizergenerators com Proof of purchase may be required for warranty claims Keep a copy of the original receipt UPC code and serial number with this manual Customer Service 1 877 528 3772 toll free support energizergenerators com ENergizer 36 EMISSION CONTROL SYSTEM WARRANTY Your new Midland Power Inc engine complies with the U S EPA Environmental Protection Agency reg
22. pected Once the device starts up the overload indicator light will shut off and the output light will remain green Ensure device wattage consumption does not exceed the generator s maximum peak output Disconnect battery reset breaker and test the battery for shorts Clean battery connector nodes Verify device start up requirements Wattage consumption Do not exceed the generators maximum peak output Remove all loads reset breaker and check device for defects Do not exceed generator rating Ensure device s wattage consumption does not exceed the generator s maximum peak output Carburetor in need of tuning For details on how to adjust correctly please contact your local service centre or contact Midland Power Inc at 1 877 528 3772 Atmospheric temperature high excess of 35 C Insufficient air circulation in vicinity of generator Low oil viscosity Use oil according to oil usage chart in user manual on page 26 Fouled spark plug replace with equal or greater quality plug 30 Engine idle Carburetor in need of tuning For details on how fluctuates to adjust correctly please contact your local service centre or contact Midland Power Inc at 1 877 528 3772 Missing ground reference on return side of differential analog output external Air filter element obstructed by debris Clean according to user manual instructions on page 25 Engine stops Engine idles The power switch is in the Off posi
23. rain into the pan 4 Reinstall drain screw before filling the engine with fresh oil Do not overfill oil reservoir Use a funnel to prevent spillage See chart below for recommended oil 5 Reinstall the oil filler cap and tightly fasten SAE SW 40 SAE 10W 30 SAE 15W 40 30 15 15 45 Energizer 26 5 5 Replacing and Cleaning the Spark Plug Do not rinse spark plug in water Follow guidelines and be careful not to overtighten the spark plug Tighten turn when installing new spark plug Tighten turn when re installing an old spark plug 1 Unscrew and remove spark plug access panel and screws 2 Remove ignition coil from spark plug and remove spark plug with spark plug wrench 3 Inspect the spark plug and clean any dirt from the electrodes with a wire brush If electrodes are worn or show signs of wear replace spark plug 4 Measure the electrode gap with a spark plug gauge and adjust as necessary by bending the side electrodes Ensure that the gap is between 0 7 and 0 9mm 5 Reinsert the plug carefully Tighten with a spark plug wrench 27 eZVseries 5 6 Handling and Storage Handling 1 Turn off the power switch and the fuel valve when transporting the generator set Do not touch engine until the engine has cooled down Keep the generator at a level position in order to prevent spillage Storage Before storing the generator set for an extended period 1 Ensure that t
24. rranty support in the future Product registration is required for all product support and warranty coverage Warranty support operation assistance and product support is provided by Midland Power Inc a licensed manufacturer of Energizer Generators Please contact us directly for any warranty service questions 1 877 528 3772 support energizergenerators com www energizergenerators com Energizer 6 CONTENTS Safety First 8 Safety while using your generator 8 Understanding AC safety 9 Safety while maintaining your generator 9 Other safety tips 10 Learn About Your Generator 11 Identification of componants 11 Making sure you have everything 13 Setting Up Your Generator 14 Checking the oil level 14 Checking the air filter 15 Using Your Generator 17 Initial startup of your generator 17 Operating your generator 19 Shutting off your generator 21 Using your generator with appliances 22 Using the generator to charge automotive batteries 22 Maintaining Your Generator 24 Maintainance Schedule 24 General inspection tips 24 Cleaning the air filter 25 Changing the engine oil 26 Replacing and cleaning the spark plug 27 Handling and storage 28 Troubleshooting 29 Specifications 32 Wiring Diagram 33 Learn About Your Warranty 34 7 eZVseries Chapter 1 Safety First Playing it safe when working with power equipment is always a good idea Here are some important prec
25. sonnel with knowledge of fuels electricity and machinery hazards should perform maintenance procedures e Lubricate all exposed metal parts regularly See chapter 5 1 for maintenance schedule 1 4 Other Safety Tips e To avoid breathing in poisonous carbon monoxide from the exhaust gases adequate ventilation should be provided if the generator set is running in a partially enclosed space e Ifthe generator set is stored outdoors check all the electrical components on the control panel before each use Moisture can damage the generator and can lead to an electric shock e Generators vibrate in normal use During and after the use of the generator inspect the generator as well as extension cords and power supply cords connected to it for damage resulting from vibration Have damaged items repaired or replaced as necessary Do not use plugs or cords that show signs of damage such as broken or cracked insulation or damaged blades e lf you start to feel sick dizzy or weak after the generator has been running move to fresh air RIGHT AWAY See a doctor You could have carbon monoxide poisoning Energizer 10 Chapter 2 Learn About Your Generator This section will show you how to identify key parts of your generator Going over the terminology below will make sure we re on the same page 2 1 Identification of Components Choke Lever Fuel Cap Fuel Valve Control Panel Engine Access Panel Spark Plug Access Pane
26. tion down and The engine is out of gasoline Add regular shuts off unleaded gasoline A r filter element obstructed by debris Clean according to user manual instructions on page 25 Adjust choke lever according to user manual instructions on page 20 Incorrect oil being used or insufficient oil level Always ensure high oil levels and use oil according to oil usage chart in user manual on page 26 Fouled spark plug replace with equal or greater quality plug Refer below for a complete list of spark plug compatibility codes SPARK PLUG COMPATIBILITY BRAND EZV SERIES NGK CR7HS DENSO U20FPR CHAMPION RZ10YC BOSCH U24BC 31 eZVseries Chapter 7 Specifications EZV2200 EZV2800 EICHE 2 Rated frequency Hz 0 3 80 HP Single Cylinder forced 5 3 HP Single Cylinder forced air cooling 4 stroke OHV air cooling 4 stroke OHV 91 Oct Unleaded Gasoline en Packaging Product Weight kg 35 5 33 5 38 36 ENergIZer 32 Be Transistor Controlled Transistor Controlled Ignition mode es Ignition Ignition a 2 lt a Z gt ad E a a Chapter 8 Wiring Diagram 22 VLAS 8801 wpa aay 91 ONIANNOYO vol OG amd _ 490s 90 yov a Woe NOW TE t HOLIMS 4018 702 038 HOLIMS Woz Nove Foe TANVd TONLNOOD ONIAIM 008ZAZA 00CCA
27. ulations State of California emission regulations models certified for sale in California only and Canada EPA regulations Midland Power Inc provides the emission warranty coverage for engines in the United States and its territories Midland Power Inc provides the emission warranty for engines in the 13 provinces and territories of Canada In the remainder of this Emission Control System Warranty Midland Power Inc will be referred to as Midland Power Inc YOUR WARRANTY RIGHTS AND OBLIGATIONS California The California Air Resources Board and Midland Power Inc are pleased to explain the emission control system warranty on your Midland Power Inc engine In California new spark ignited small off road equipment engines must be designed built and equipped to meet the State s stringent anti smog standards Other States U S territories and Canada In other areas of the United States and in Canada your engine must be designed built and equipped to meet the U S EPA and Environment Canada emission standards for spark ignited engines at or below 19 kilowatts All of the United States and Canada Midland Power Inc must warrant the emission control system on your power equipment engine for the period of time listed below provided there has been no abuse neglect or improper maintenance of your power equipment engine Where a warrantable condition exists Midland Power Inc will repair your power equipment engine at no cost to you in
28. vided without registration from original date of purchase and after transfer of ownership This transfer form must be completed on or before the date that ownership change takes effect Warranty coverage continues from original date of purchase and is not extended by transfer of ownership TRANSFER OF OWNERSHIP AND WARRANTY Existing Owner Information First Name Last Name Company Street Name and Number City Postal Zip Code Province State Phone Number Other Contact Number Fax Number Email New Owner Information First Name Last Name Company Street Name and Number City Postal Zip Code Province State Phone Number Other Contact Number Fax Number Email Product Information The serial number can be found on the Generator or on the exterior of the packaging Model Name Serial Number Initial Date of Purchase Warranty Expiration Date of Transfer Add 2 years to initial date of purchase NOTE Transfer of ownership does not act as a warranty extension The original 2 Year Warranty is effective as of the Initial Date of Purchase and continues after ownership has transfered New owners should be made aware of expired or remaining coverage L 4 41 eZVseries Enjoy Be sure to check energizergenerators com monthly for updates regarding your generator
Download Pdf Manuals
Related Search