User Manual
Contents
1. will starts regular testing automatically Test mode at idling speed Conduct the injecting test as following Injecting RMP 750r min Pulse Width 3ms Count 2000 Timing 160s When the producer is over observe the injecting uniformity and replace or clean it if the value is more than 9 Test mode at max loading Conduct the injecting test as following Injecting RMP 2400r min Pulse width 12ms Count 1000 This program can observe the injecting volume at the max loading Test mode at high speed Conduct the injecting test as following Injecting RMP 3000r min Pulse Width 6ms Count 1000 Timing 20s This program can observe the working state at high speed Test injecting with complete procedure During this procedure Pulse width is 3ms RMP is 750r min then the RMP will up to 9975r min Pulse width will up from 3ms to 12ms then down to 1 1ms Total cycles is 5 times and running time is 20s observe for 30s after the test then the liquid will return for 30s During the automatic test press Selection to pause it as you need Test mode of editing procedure Every time press Selection key rotation speed pulse width count and timing signal lamp displays successively It indicates in current state when the signal lamp lights Press or 1 to select Suitable rotation pulse width timing and count then press Manual Use the Ultrasonic Cleaner 1 Before starting the machine put in the special cl2. Safety Guide The BulletPro V8 8 cylinder injector cleaner is specially designed for testing and upholding the electronic injector including K injector CIS and so on Safety guide lines listed below 1 Don t use petrol as test fluid 2 No fire no smoking Keep well ventilated 3 Use the special test liquid and cleaning detergent only If use other brands may damage the paint coat fuel pump and sealing ring 4 Use A C 240V 50 60 Hz 5 Use power with grand wire 6 Put the machine on well ventilated environment and keep ground dry 7 Turn off the power if don t work for a long term 8 Discharge the test liquid and cleaning detergent from the side Be careful when discharging the testing cleaning fluid and be aware that testing cleaning fluid leak will damage the internal boards N Technical Parameter Dimensions 510mm x 500mm x 450mm Weight 30kg Power 85 132vac 170 264vac 47 63Hz Fuel tank capacity 4 5L Test tube capacity 120CC Ultrasonic wave frequency 25KHz Ultrasonic wave power 100W Rotate speed 0 9975r min step 25r min Pulse width 0 30ms step 0 1ms Count 0 9975r step 25r Time 0 9975S step 5S System pressure 0 6 2kg c m variable regulated System flow 4L min Test cylinder 8 max I Specifications amp Functions BulletPro V8 Fuel Injector tester amp Cleaner mainly applies to fuel injector testing cleaning and quality analysis The functions as f
3. cleaning system lt uses environmental protective and safe test fluid and cleaning detergent accords with Montreal Agreement innocuous with no peculiar smell non volatile and can be reclaimed repeatedly and effective it s innocuous with the operators Appearance Components i 2 Fae o a serang Standard feediuelboard S Connector otier Yd i 7 rPowerswich v rPowerpugin v Cleaning tank Let out vent y gt SWARNING If use the test liquid of other brands may corrupt O ring please use the test fluid and detergent we appointed Use the Fuel Injector tester amp Cleaner 1 panel direction BulletPro V8 Low Level High Level Uftronic Cleaner Device Selection Press the key start the test mode at idling speed rotation speed pulse width timing and count signal lamp displays in proper order numeral tube shows 750 3 160 2000 successively Press again start the test mode at max loading signal lamp lights numeral tube shows 240 12 25 1000 successively Press it again start the test mode at max rotational speed numeral tube shows 3000 6 20 1000 Press again start the test mode at injecting capacity in 15S numeral tube shows 15S 2 Valve Press the key the signal lamp lights valve opens the unit begins to back drain the liquid The signal lamp turns off valve closes After 10 minutes the program stops automatically 3 Lighting Press the ke
4. eaning detergent normally the liquid level is 3 4 of the cleaning groove Don t start the machine when the groove empty 2 Program 1 Insert the power 2 Press the power key now starts working tacitly approve 10 minutes then stops automaticly If need 20 or 30 minutes press the corresponding key and the indicator lights on 3 If need change the cleaning detergent let out the liquid through the switch at the back of the machine V Installation a nE Install the connecter 1 010 6 connecters Suitable model Top feed injectors TOYOTA HONDA NISSAN MAZDA HYUNDAI FORD GM CHEVROLET 2 013 6 connecters Suitable model Top feed injectors BOSCH AUDI VOLKSWAGEN VOLVO 3 Side feed connecter Suitable model NISSAN PREVIA TOYOTA MAZDA 626 929 DAEWOO V Parameter of Fuel System Pressure prandorcar Moet System Pressure 3 3 6 9 VOLVO VOVLE 2 1 2 9 300ZX 2 06 2 55 FORD LINCOIN TOWEN 2 06 3 08 BUICK SENTURY 2 9 3 3 BUICK AVENUE 2 9 3 3 CADILLAC 5 7 2 9 3 3 D S C woonse 30 SIX CYLINDER 2 8 3 0 AUDI FOUR FIVE CYLINDER 4 5 5 0 Fuel Injector Tester amp Cleaner Packing List components um ay romans 4 Fuel Injector Tester amp Cleaner pe Couple of standard board include 8 International standard connectors 10 6 Sealed ring of International standard connectors 5x2 7 5x3 5 European standard connector
5. els 45 Sealed ring of annular connector of Mazda 929 pe 16 po 8 014 underlay of injector 011 underlay of injector Pulse line of injector Nut for fixing pole Fuel pump filter Injector support frame
6. l pump key at the front door of the machine When the fuel pump works adjust the knob as the proper pressure needed A NOTICE Ifthe oil in fuel tank is too little don t open the fuel pump or may damage it A NOTICE The main machine use test fluid Ultrasonic wave machine use cleaning detergent Never mix detergent into test liquid especially not to take detergent as test fluid otherwise it will cause damage of pump and other components 3 Selective testing and cleaning 1 Dribbling test Select the corresponding connectors and fit them on the injectors them check the breakage and distortion of the O ring of the injectors replace it if damaged Put the injectors on the test stand and then connect them well Press Fuel Pump key to start pump running Set the pressure to the manufacturer specified value 10 higher is the best by press or 1 to observe the dribbling state Replace the injector if the dribbles one more drop in 1 minute or identify it according technical standard 2 Test the injector angle and atomization states Press Selection key to start the cleaning test and observe injecting angles and atomizing states Injecting angles should be identical or identify it according to technical standard and injecting well distributed without jetting or replace the injectors 3 Test injecting volume Press Fuel Pump key to adjust the system pressure then press Selection key to start cleaning and testing p
7. ollowing ly 28 3 4 10 11 12 13 PA 14 15 To test and analyze the injecting state To test the injector dribbling To test the injecting angle and atomizing To test the injecting volume To test the injector uniformity To test conduct the physical and chemical cleaning of the blocked or trouble injector ultrasonic cleaning test cleaning and on vehicle cleaning To test the open and close injecting pressure of the injector User can clean the engine without dismantling choose matched connector User can operate the auto static test dynamic test and selective test with the injecting dribbling angles atomization uniformity of one or more 1 8 injectors can simulate any state of the vehicle to observe the complete process of injectors User can operate automatically reversely and ultrasonic cleaning with one or more injectors at different state such as high resistor low resistor electric voltage and electric current User can test by count mode and timing mode also have backlight can observe the injectors clearly If use new type injector just need choose the matched connector and replace the O ring It adopts united design of microcomputer skill and intelligent engine and suppose driving power and specified injecting protection system ensure to operate the test and clean at any mode such as high resistor low resistor electric voltage and electric current Have powerful safe and time ultrasonic
8. ress Manual key for 15S observe the injecting volume should be 38ml 42ml or test it according to technical standard or replace the injectors 4 Test injecting uniformity Press Selection key to start uniformity test the numeral tube shows 750r min pulse width 3ms timing 120s count 2000 times Press Fuel Pump key to set the pressure to system pressure of serviced vehicle press Manual key observe the injecting volume of each injectors the uniformity less than 9 in each test tube is good or test it according to technical standards replace it if the volume is more than 9 4 Automatic testing and cleaning 1 2 3 4 5 5 d Before automatic testing and cleaning press Fuel Pump key to start it and set the system pressure to the value of the serviced vehicle 10 higher is the best then press Auto key to start automatic testing and cleaning during this program press Selection key the system will back to initial state Test injecting angles atomization dribbling and automatic testing and cleaning Press Auto key keep injecting for 15s time value decreases to 0 can observe the injecting angles atomization and volume replace or clean the injector if appears gush unusual angels and unusual volume Stop injecting for 30s and observe injecting volume time value shows 30s the liquid will back to the fuel tank in the following 30s Then start dribbling testing for 60s if no dribbling the unit
9. s 013 6 Sealed ring of Benz mechanical injector ia sealed ring of European standard connectors connector 5x3 Ea Connector of Benz mechanical injector M12x1 5 pp 8 fo a Sealed ring of Audi mechanical injector connector pepe 5x2 Connector of Audi mechanical injector M10x1 5 pe 7 T T E F A E T 11 Annular injector bank plug egef 12 Sealed ring of annular injector blank plug pe 4 13 Crossboard pe 14 Crescentboard pe ft 15 Gueypost pe 16 Special line of Buickinjector pe 17 Special ine of minibus injector pe 18 Injector plate O14 flat plate pe 19 Connector of soft pipe injector pe 20 Adjustable fastener pe 21 R1 4blankpg pe 22 Fuelppe pe fe 23 Adjustablehead pe 24 Fixedscew pe 25 Fuelfeedfunnel pe 26 Dust proof cover pe ft 27 Ultrasonic cleaner sot P 28 Testud le 29 Cleaning detergent pe ft 30 Wheeled machines sot tt 31 Whee pe 32 Toolbox pe ft 33 Powerline pe 34 User manual sot 35 Cross board screw pe 36 Annular connector of Nissani pe 8 oe e 38 Annular connector of Nissan pe 39 Sealed ring of annular connector of Nissan2 pe 16 40 Annular connector of Nissans pe 41 Sealed ring of annular connector of Nissans pe 16 10 42 Annular connector of Toyota ope 8 43 Sealed ring of annular connector of Toyota pe 16 44 Annular connector of Mazda 929
10. y the signal lamp and the backlight light press it again the lamp turns off With the automatic protect function in 10 min under the stop state 4 Parameter Press the key select and set rotation pulse width timing and count Indicator shows the current parameter state 5 Auto Press the key starting working as the set up program 6 Manual Press the key operate manually press selection key firstly to set the test program press it again start working 7 Stop Press the key stop during the test only apply to manual function 8 Press the key increase or decrease the data of rotation pulse width timing and count 2 Test operation Step 1 Test the impedance Remove the serviced injectors from vehicle and mark them by sequence Measure the impedance value of each injector by the digital multimeter and the impedance difference of each nozzle should not be more than 1 Q or replace them Step 2 Connect the power Insert the power in the outlet at the back connect 240V A C power and switch on the power at the right the screen shows 2000 finally Step 3 Test the minimum liquid level When starts the machine the minimum liquid level indicator lights on now please put in the test liquid from the inlet open the top cover at the right of the machine Normally it needs 1 6L test liquid If the liquid level excessive max liquid level indicator lights please let out the excessive test liquid Step 4 Press the Fue
Download Pdf Manuals
Related Search