GSM Voice Auto Dialer& SMS sender JC
Contents
1. 4 Inquire programming password 5 7 LCD display password Remarks 1 Password must be 4 digits if less or more than 4 digits LCD will display E Remarks 2 Defaulted programming and arm disarm password both are 0999 and they can be programmed independently Remarks 3 If forget password user can press RESET button one electric board both password will be reset to 0999 Other information will not be changed 4 7 Remote control phone number programming total 4 numbers 1 Press 6 LCD display PREMOTE input X X is 1 4 optional phone number Example 6 1 15800000000 to program the first remote control number is 15800000000 display A means correct 2 Inquire numbers for remote control 6 X LCD will display the number 3 To clear the number 6 X for example 6 4 LCD will display A 4 Only numbers stored can remote control the auto dialer such as remote arm disarm by call and SMS If 4 numbers are blank means deactivate remote control operation Defaulted is deactivated Remarks User needs to fill area code for fixed phone number for remote control For example area code for NEWYORK is 212 and fixed phone number is 11110000 then number input should be 21211110000 4 8 Reset to factory defaulted setting 7 999 LCD display A 4 9 Program zone type Operation Press 8 LCD display PSAFE input 1 to set it as 24h zone or input 2 as arm disarm controlled zone Example 8 1 set it as 24h zones 8 2 set2. it as arm disarm controlled zones 4 10 Alarm delay Operation Press 9 LCD display PDELAY input 1 to set as alarm delay 0 5s or input 2 as alarm delay 30s Example 9 1 alarm delay 0 5s 9 2 alarm delay 30s Remarks alarm delay means the time between high level was triggered and dialer begin dialing 4 11 Exit programming Press to exit LCD display PgMode End 5 Record voice message and play record Recording Support 20svoice message To begin record by press REC key on dialer keypad LCD display recording user can record message by facing to MIC on dialer Play voice message to press PLAY key on dialer LCD display playing record return to programming state after play over 6 Arm disarm on keypad Arm press ARM key and then input password and LCD display ARM finish Disarm press DISARM key and then input password and LCD display DISARM A ARM delay press ARM key and then input password and 1 LCD display ARM delaying arm delay successfully delay 1min 7 Remote arm disarm by phone call 1 Use the phone numbers stored in item 4 7 to call the dialer dialer will refuse the other call 2 After get through input 1 on phone dialer will be armed and will report A R M If input 2 dialer will be disarmed and will report D I S A R M 8 SMS arm disarm 1 Use the phone stored in item 4 7 to send sh
3. GSM Voice Auto Dialer amp SMS sender JC 999 User Manual 1 Description 1 1 Main features a 2 3 4 5 6 7 8 9 10 11 12 Large LCD display integrated keypad human friendly programming Support 12 alarm receiving numbers Triggering means N C N O and voltage trigger optional Alarm delay time 0 5s and 30s optional Support to stop all alarm call on mobile phone to avoid trouble by fault alarm 20s changeable voice message Short message can be updated Phone call SMS arm disarm and arm disarm on keypad Programmable zone characteristics 24h zone or arm disarmed zone Support reset the password by RESET key Arm disarm password and programming password can be set independently High capability battery standby time more than 48h 1 2 Specification C1 2 3 4 World universal GSM band 900Mhz 1800Mhz 850Mhz 1 900Mhz Rated voltage DC12V Standby 4mA 12V Working current 300mA 12V 2 Main parts description GSM Voice Auto Dialer RE RA abi HRB REC PLAY ARM DISARM Mic Microphone face to the microphone when recording voice message 1 Wiring terminals Z Zone and signal input to connect infrared sensors door sensors panic buttons alarm panels etc Wiring terminals and near the jumpers power output provide power for sensors panic buttons if necessary Remarks battery voltage is 3 7V only for providing power to auto dialer please
4. check the 6 number 4 Delete phone numbers stored 0 X remarks X 1 12 example 0 12 to clear the 12 number 4 2 Program text short message support more than 90 letters Remarks Defaulted message is Voice auto dialer alarm 1 Press 1 LCD display PgMode PSMS and dialer will wait to receive short message about 2min 2 Send the programmed short message to auto dialer by mobile phone 3 Auto dialer will display the message text and reply message OK to mobile phone to read the message by REC and PLAY keys as up and down button 4 If dialer didn t receive message it will exit user can start again by press 1 or exit by press 4 3 Check alarm means stored 1 press 2 LCD display PgMode PALMTST 2 to press the number group No and to test For example 2 1 to test the first number 3 If test finish display means test success and return to programming mode you can continue to test others or esc 2 by press Remarks If test failures always please check if number stored is correct SIM card charge and GSM signal level 4 4 Program repeated dialing times when alarm failure 1 Press 3 gt LCD display PTRY repeated dialing times 0 9 optional gt display A and return to programming state Example 3 2 means to program the repeated dialing times as 2 2 Inquire repeated dialing times stored 3 36 LCD will display times stored Remarks 1 defaulted repeate
5. d dialing times is 3 Remarks 2 SMS alarm is not restricted by repeated dialing times dialer will send one time only 4 5 Program voice dialing stop means Option 1 defaulted value automatically stop dial the present number after answer successfully and dial according 4 4 items programming if dialing failed Option 2 after answer the alarm call you must press 9 on phone to stop all call dialer will dial according to 4 4 programming if not pressed 9 or dialing failure Remarks if hang up the call after answer means alarm successfully dialer will not dial this number in next cycle If refuse the alarm call means alarm failure dialer will dial this number next cycle Operation 1 Press 4 LCD display PSTOP input repeated dialing times 1 2 display A 2 Inquire stop means 4 45 LCD display 10r 2 and make atone Du Remarks When reply 9 after answer the call you are suggested to wait until voice message play over will hear a Di tone if reply successfully 4 6 Program the programming password and arm disarm password 1 Program arm disarm password 5 XXXX X is 0 9 optional Example To change the arm disarm password as 1234 press 5 LCD display PPASS input 1234 LCD display A 2 Inquire arm disarm password 5 7 LCD display password 3 Program programming password 5 XXXX Example To change the arm disarm password as 8118 press 5 LCD display PPASS input 8118 LCD display A
6. don t power for sensors connected when didn t connect to external power and use battery only Jumpers To choose zone triggering type please place the jumpers on the proper pins according to signal input type reference to below table DC 12V To connect to 12V power adaptor Jumper setting looking from the back side NC NO open circuit alarm short circuit alarm Voltage trigger 2 3 42 S 12 38 Ue AZZ EH sia e M e E m e M 3 Start up Auto dialer will start up automatically after connect power adaptor When use battery only please press DISARM key for about 1min until the LCD light up LCD will display JC 999 and then disappear after 2 seconds Later zone type 24 ARM DISARM and GSM signal 0 5 level will display on LCD for example DISARM 5 4 Enter programming Input 0999 LCD display PgMode Programmable items see below please means and it is only a mark in below operation description 4 1 Program alarm receiving numbers total 12 numbers 1 Press 0 to enter number programming mode LCD display PgMode PNUM 2 Input serial number 1 to 12 phone number 1 2 press 1 to choose voice alarm press 2 to choose SMS alarm Example 0 1 13888888888 1 the first phone number is 13888888888 choose voice alarm 0 2 18911111111 2 the second phone number is 18911111111 choose SMS alarm 3 Check phone numbers stored 0 X remarks X 1 12 example 0 6 to
7. ort message DISARM dialer will be disarmed and reply OK after done 2 To send short message ARM dialer will be disarmed and reply OK after done 9 Cautions please 9 1 To press to exit programming state when finish operation and to arm the dialer If didn t exit it will lead to alarm Failure if zone is programmed as arm disarmed zone 9 2 Do not use SIM card with PIN code protection function If SIM card attached with the function insert the card in other mobile phone to close the function for example using Nokia mobile phone choose Menu setting security settin gt PIN protection off
Download Pdf Manuals
Related Search