2014-1-14_MA300+FR1200 installation guide v2.0.cdr
Contents
1. MA300 IP65 Installation Guide N Warning No operating with power on Version 2 0 Date December 2013 ee ee 3 Lock Connection 1 The system supports NO LOCK and NC LOCK For example the NO LOCK normally open at power on is connected with NO terminal and the NC LOCK is connected with NC terminal 2 When the Electrical Lock is connected to the Access Control System you need to parallel one FR107 diode equipped 1 Equipment Installation in the package to prevent the self inductance EMF affect the system do not reverse the polarities I Share power with the lock Device share power with the lock Uocx 12V I Itock gt 1 A a DC12V 1 Post the mounting template on the wall 2 Remove the screw on the Drill the holes according to the marks on the bottom of device template holes for screw and wiring NO LOCK And the lock is near to the device Z C od penne Gnp DC12V Device does not share power with the lock A Utock 12V_I Itock 1A B Utocxk 12V C The lock is far apart from the device 4 Fix the back cover on the wall according to the mounting paper ee ee Rt Tn a a a a a a a a et a ra rr a a a Rt a ta eh a en ah he a at ea ae NO LOCK i i I device output current ULock lock voltage ILock lock current Access Co2. e installed each side of the door to control the lock and access together Notes 1 Please keep the distance between the device and Access Control or reader less than 90 meters Please use Wiegand signal extender in long distance or interference environment _ 2 To keep the stability of Wiegand signal connect the device and the Access Control or reader in same GND in any case Ce ee ee ee m Other Functions 1 Manual Reset If the device does not work properly because of mis operation or other abnormality you can use Reset function to restart it Remove the black rubber cap then stick the Reset button hole with a sharp tool the tip diameter less than 2mm f Bottom Front og obo Reset button Figure 8 1 Connect to Access Contrl 2 External USB Keyboard Refer to your own keyboard m The device supports external keyboard to offer more flexible 0 80 00 0 i O operations The keyboard need to purchase separately It s convenient to enroll users remove users recovery factory settings set the keyboard password and so on The operation Bottom Fi 8 2 please
3. ntrol System Function TCP IP i RS232 RS485 1 Ifa registered user verified the device will export the Converter signal to unlock the door 2 Door sensor will detect the on off state If the door is unexpected opened or improperly closed the alarm i signal digital value will be triggered i 3 If the device being illegally removed the device will l t export alarm signal Exit Button eg GND 4 External card reader is supported G 5 External exit button is supported it is convenient to en i 0 1 1 oor Sensor open the door inside i OO 6 Supports RS485 TCP IP modes to connect with PC Input DC 12V 500mA S0mA standby i Card Reader Exit Button 1 l oe i ae od One PC can manage multiple devices Positive is connected with 12V negative is connected with GND do not reverse the polarities i E i l Alarm Power Alarm Alarm Voltage output lt DC 12V for Alarm ee i ww www ww wwe ww www ww we ww ww www ww ww ew www wwe ww ww ww www www www www www www ww www www ww www ww ew wwe we ee ee we we ee ee ee eee eee ee eee A y OCennnenneeeeeeee m De ee ee ee ee ee ee ee ee ee ee ee ee ee mE ese ewer ess es 6 Wiegand Output TN The device supports standard Wiegand 26 output as a The device has the function of Wiegand signal input It supports reader device it has a very good compatibility to connect with an independent reader They ar
4. refer to the user manual igure Keyboard 3 Recovery Factory Settings You can use the tamper switch As figure 8 3 to recovery factory setting such as device number system password IP address RS485 address etc More information please refers to the user manual Press the tamper switch three times after the alarm being triggered 30 seconds but no more than 60 seconds Pe T Note The user data won t be cleared RS485 BUS Pe ee i 485A Back Note When installation keep the magnet on the iron plate Or it will trigger E the tamper alarm T gt Tamper Switch seen au Figure 8 4 Figure 8 3 9 Communication There re two modes that the PC software communicate and exchange information PE Seral Banc with the device RS485 and TCP IP they all support remote control 485A RS485 4 1 RS485 Mode 485B RS485 Please use specified RS485 wire RS485 active converter and bus type wiring eee et oe a ee a ne em a ne ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee a ee he hh he ee ee ee a ee To switch the communication function of the RS485 reader you need to restart the device I To prevent the interference the last device in the RS485 bus connect a 120 Euro resistor Tha
5. t time MA300 beeps once that means RS485 reader function has been disabled The MA300 communicates with the computer in RS485 mode 2 After a user swipes the management card seven times if the last time MA300 beeps twice that means RS485 reader function has been enabled The MA300 communicates with the RS485 reader Access Control Device Notes When the communication distance between the FR1200 and master is longer than 100 m the FR1200 must be powered separately 10 Cautions 1 Power cable is connected after all the other wiring If the device is working abnormally please shut down the power first then make the necessary check Kindly reminds you that any hot line work may damage the device and it is not included in the warranty 2 We recommend the 3A 12V DC Power supply Please contact our technical staff for details 3 Please read carefully the terminal description and wiring by rule strictly Any damage caused by improper operations will not under warranty 4 Keep the exposed part of wire less than 5mm to avoid unexpected connection 5 Please connect the GND before all the other wiring especially under the environment with much electrostatic 6 Do not change the cable type because of long distance between the power and the device Pay attention to the distance Warning No operating with power on ee oe ee eee ee Ea voltage decay when you choose the power cable
6. t is turning the switch 4 terminal resistor switch to ON II The RS485 device No is shown in PC software You can change it as follows The default switch state is OFF ON KE Enlargement of slide switch l 2 3 4 The printing number is the device port number Port 1 2 3 is to set RS485 address device number L ste Ton ow ow PN Wop mw O a ws Yo Yl Nos CU Nos YW v N6 v vV N7 VY vw VW The symbol VY means turning the switch to ON position ON KE No 3 machine s slide switch 1 2 3 4 2 TCP IP Mode 1 Crossover cable The device and PC connected directly As figure 9 2 ID Straight cable The device and PC connected to LAN WAN through switch Lanswitch As figure 9 3 Port 4 is to set the state of terminal resistor IP Address 192 168 1 201 Seon anewich Subnet Mask 255 255 255 0 IP Address 192 168 1 124 Subnet Mask 255 255 255 0 Figure 9 2 3 485Reader Function The MA300 supports the RS485 reader function and it can be connected to the FRI200 reader through the RS485 The RS485reader function can be switched by swiping the management card seven times 1 After a user swipes the management card seven times if the las
Download Pdf Manuals
Related Search