Information
Contents
1. ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 27MHz HAND HELD GIGALINK TRANSMITTERS GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 and GLT2708 Features ET e Over 4 billion code combinations i e Can program any number of transmitters to a receiver e High Security Applications e Remote control of garage doors gates lights alarms rife se RA fi Description These hand held GIGALINK transmitters operate on 27MHz These GIGALINK transmitters can be programmed to the 27MHz Gigalink receivers The GLT27 series 1s available with 1 2 3 4 and 8 buttons The transmission is secure with over 4 billion code combinations The hand held GIGALINK transmitters have single and multi channel code programming system that provides flexibility in programming each channel to different receivers Each transmitter button can be programmed to different single channel receivers Multi channel Code Programming This is used to program all channels from a multi channel receiver to the multi channel transmitter To Multi channel code program a transmitter read receivers setup instructions Single Code Programming This is used for programming one channel at a time to the transmitter To single code program a transmitter read receivers setup instructions Operating Distance An operating distance in conjunction with our GLR27 series receivers of 350 metres is po2. ch is a hand held GIGALINK transmitter without the front membrane This enables the customers to fit their custom made membrane that can be a 1 2 3 or 4 channels This has the advantage of customers only stocking one model to function as a 1 2 3 and 4 channels Details of membrane dimensions are given below lt 48 0 or lt q 24 0 Center of LED hole 4 0mm GIGALINK TYPE GLT2704 GIGALINK GLT2708 Center of LED hole 4 0mm ELSEMA Customers who wish to have their own membranes can contact us with their designs on 61 2 9609 4668 You can have your own company logo and specific text printed on the membranes e g Up Down Right and Left or Start Stop etc The minimum quantity for custom membranes is 50 pieces per order ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 REGULATORY COMPLIANCE STATEMENTS American Users This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a resid
3. e 5 to 50 C Range Modulation Freq 1 8kHz 1 737kb 15 1 8kHz 0 56 ms bit 15 tolerance tolerance Necessary Bandwidth 2 5kHz Digital Coding System Microcontroller based 96 bit word Code Combination 4 294 967 296 Digital Channels 1 2 3 or 4 channels The 8 channels On board 16 pin IC type of membrane label socket Channels are addressed by determines the number of joining opposite side of the IC channels Customers can fit socket pins Elsema has a 16 pin custom made membrane 35cm ribbon cable plug available labels Dimension 81 x 56x 24mm 130 x 67 x 27mm GLT2708 pen 35g GLT2708NC ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 Connection Diagram GLT2700NC ELSEMA Controller A 27 195 Mhz Elsema PTY LTD Ghi an Cho Gh4 Gnd SERRE E F Ground Coding Socket Bottom side Connection Diagram GLT2708NC Note A Internal Socket Connection Channel 1 Crystal Controlled Elsema s Microcontroller oN Ald vWaS 13 sixteen Pin IC Socket See Note A solder taps for battery clip Channel 8 Mounting Ground Coding socket Terminal Block Mounting for DC Supply Hole ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 Customised labels Membrane is the front label with the channel etched printed to it Customers can purchase the GLT2700 whi
4. e This enables Elsema to offer everyone your own radio control Case The hand held GIGALINK transmitters are supplied with a case There is also sufficient space on the rear of the case to place additional stickers such as your telephone contact local authorities approval numbers etc The GLT2700NC and GLT2708NC are No Case versions This allows the transmitter to be integrated according to your needs Products in the Range GIGALINK GIGALINK fr i E GIGALINK TYPE GL rept NL No label The Elsema Label is absent GLT2708 GLT2716 GLT2700NC GLT2708NC 8 Channel 2 Stroke Transmitter 8 Channel 16 Channel No Case No Case Option Pin header ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 Technical Data Model GLT2701 GLT2702 GLT2708 GLT2703 GLT2704 Power Supply 9V Battery Applied to the 9V Battery Applied to the battery battery Clip Clip or 10 16VDC Only applied to amp terminals Current Consumption Max 45mA at 8VDC Only Max 70mA at 12VDC Only when when transmitting transmitting Standby Current 10uA Typical Transmission Modes Continuous Transmits as long as the channel is activated Battery Monitor LED flashes at 1Hz during transmission when battery voltage is at 6 5V flat 9V battery Operating Frequency 27 195MHz Carrier Frequency Crystal controlled 30 parts per million Tolerance Operating Temperatur
5. ential installation This device generates uses and can radiate radio frequency energy and if installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the computer and receiver e Connect the computer into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Caution Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment Canadian Users This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du Reglement sur le mat riel brouilleur du Canada European Users This information Technology Equipment has been tested and found to comply with the following European directives ETS 300 683 JETS 300 220 Australian and New Zealand Users This device has been tested and found to comply with the limits for a Class B digital device
6. pursuant to the Australian New Zealand standard AS NZ 4268 2012 set out by the Spectrum Management Agency
7. ssible The operating distance depends upon the receiver antenna and location An independent test revealed the following ranges Range Metres Receiver Type 507 250 mm Long Wire GLR27 50 1000 mm Long Wire GER27 ANT27M GLR27 Range tests were done in an open area test site with line of sight operation and the receiver antenna wire was fixed vertically away from any metal objects Applications The code programming becomes a powerful feature that allows the hand held transmitters to be used in many diverse applications such as security gate operation panic buttons multiple on off functions etc ELSEMA 1 2 3 4 8 Channel 27MHz GIGALINK Transmitter GLT2700 GLT2701 GLT2702 GLT2703 GLT2704 GLT2708 Battery or DC Supply Battery operation is optimised using the built in battery monitoring system The battery monitoring system alerts the user when the battery level falls below the low battery voltage The 1 Hz flash from the LED during a transmission indicates low battery This is an indication that replacement of a battery is necessary The GLT2708NC has the option to operate from a 9 volt battery or DC power supply DC power supply is connected to the 2 way terminal block Do not connect the supply to the 2 5 mm coding socket since connection may damage the microcontroller Also available with a 5 Pin header for inputs Unique Code System The microcontroller EEPROM allows large volume users to have a unique cod
Download Pdf Manuals
Related Search
Information information information synonym information technology information systems information security training information and software technology information technology jobs information security management system information security information ratio information literacy information security program training informational interview information society information sheet information assurance information overload information security army information is beautiful information technology jobs near me information may be cui in accordance quizlet information security program training army information gathering information and communication technology information cocoons