User Manual - Lehner Lifttechnik
Contents
1. 4 Error search 1 Is_the connector from the electric power supply put into the outlet Put the connector into the outlet 2 Is the outlet switch on Turn the outlet switch on 3 Electric power supply there Maybe the fuse is damaged Control the fuses and exchange them if necessary 4 Is the emergency connection on Release disconnect the emergency connection through turning the button until it jumps out 5 The platform can t drive upwards but not downwards Remove impurities on the securtiy band Control the security band if there are other obstacles 6 Is the connector connection between the electric power supply_and the platform made Put the connector on Call the company Lehner Lifttechnik if you can not solve the above mentioned defects 6 Technical data Platform Typ 1 maximun height Ofstirokesa asen naar aaa 600 mm OAC CapaclVe ne ee exes E E N geese 180 kg WIIG SPEEA 2csic cestecanceesccwecnsiddeasviaccesscaad dua eraucarergiedseuseiaccussreadseasbyaeeaiacead deaunaads 10 mm s minimum height HEACGFOOM cccccccccccecececeeeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 110 mm Weihe a E E EE EEE ea Ea E Ea r SE 52 5 kg electric power Supply ccceceeeeeeeeeeeeeeeeeeeeeees 24 V through transformer on 230 V grid inside dimension length nee aa 1170 mm Inside dimension breadth eee eeecececeeseececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 710 mm Outside dimension length een 112. passage the wheelchair user can drive on the passage Down Ab function from the top level 1 The wheelchair user dirves on the platform 2 3 When you press the button Down AB the platform drives down As long as the button is pressed this function is active When the platform has reached the level and the button is still pressed the access ramp safety rail will be lowered and the wheelchair user can leave the platform 1 2 Safety function Safety curtains The pre assembled safety curtains ensure that nobody will be jammed if the platform is in the highest position and drives down Assembly and safety curtains 1 2 3 The areas of the safety curtains are pre assembled with chain belts A broomstick or something similar should be placed on the narrow side of the shear construction The safety curtains have to be put over the upper board and have to be placed on the broomstick so that they hover freely The safety curtains are lifted and assembled Always start with the angles in the other side of the access ramp on the upper board of the platform The safety curtains have to be pressed on the hook and loop tape fastener 5 The safety curtains on the other side have to be lifted and have to be assembled on the upper board of the platform The safety curtains have to be pressed on the hook and loop fastener 6 The broomstick can be removed now 7 The safety curtains will be mounted in such a way t
3. 80 mm Outside dimesnion breadth ceecccccccccceeeceeeeeeeeeeeeeeeeeeeeeeeeesuaaauaaaaaaaaaaaaaaaaas 810 mm Platform Typ 2 maximum height ofSsiroker un ER EN IR 830 mm OAC CAD ACY ADE ERINNERTE NONE T E EL T T EITT 180 kg lifting speed ana ea E Ee e EEE E E EET EEE EA 10 mm s minimum height headroom ccccccceeececeeeceeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeees 120 mm Weight sense er ee araa 71 5 kg electric power Supply ccceeeeeeeeeeeeeeeeeeeeeeees 24 V through transformer on 230 V grid ins de dimension length ass a 1495 mm inside dimension breadth 22222220400000000000000000Rnnnnn nen nn onen nennen 785 mm outside dimension length ru444444eeenennennnn nennen seen enenennnenennnennnnnn 1505 mm outside dimension breadth cccccccsscccseeeceeeeeeeeeeeeeeeeeeeeeeeaeeaaeaasaasaaaaaaaaaas 890 mm Waranty rearen se ee anew ts 1 year In many situations it is necessary to make a special adaptation of the platform whereas the above mentioned specifications can change
4. User Manual LEHNER ae LIFT TECHNIK oe A 4724 Neukirchen W Salling 8 Tel 07278 3514 15 Fax 07278 3514 12 Email office lehner gmx at Mobil 0664 3526190 Web www lehner lifttechnik at Tabel of contents 1 210 g9eneraln gnisa el 2 1 1 PFOQUucer anne 2 1 2 UHlisationsac ae 2 1 3 Important Warnings 44 44n44 BRnnn nenn nn BRnnnnnnnn nn nun nenn anne 3 1 4 Unpacking and preparation uuuu2 an000 nn00nnnnnnnnnnnnnnnnnn 3 1 5 Assembly before starting Up 42 r4s4nBBnnnnnnnn nn nnnn nenn anne 4 1 6 Assembly disassembly fitting 42 244444 BRn0nnnnn nn Rn 5 2 Describtion of Operation 22202000 20000nnnnnnnonnnnnnnnn nn 5 1 1 Eabel au onen 5 1 2 Safety function namen 6 3 Demontage amp Transport uneeuneennnnnnnnnnennnnn nn nnnnnnnnnn nn nenun nanne 8 3 1 Transport een ae euere 8 3 2 Packing during the transport ccssceceeeeseeeeeeeeeeeeseeeneeeseaees 8 4 Attendance and Keeping cccccceeceeeeeeeeeeeeeeeeeeesseeeeeeseaeeeeees 8 4 1 GleaniNng e nee 8 4 2 Keeping and storage uuurssneuunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 8 4 3 How to prevent corrosion uuuussunnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 8 4 4 Which attendance has to be made by the owner 8 5 Attendance amp durability cccccscsssseeeeeeeeesseseeeeeeeeeaeeenensees 8 5 1 Durability and atten
5. as attendance and an annual assessment of specialized staff or the company Lehner Lifttechnik GmbH Spare part lists and drawings can be requested at the producer or the trader 5 2 Fuses If a fuse drops out the cause has to be examined by qualified staff The exchange of the fuse is only allowed by qualified staff before the platform is operating again 5 3 Assessment Allround With the Attendance it has to be recorded what has been examined and exchanged Parts which show abrasion or damages have to be replaced with new original parts 1 Visual control of the product Control if abrasion can be diagnosed Control if the product has deformations Control if the product has other forms of damages 2 Examination of the product during the normal utilization All functions of the products with our without burden Control emergency lowering device on proper function Control voltage index on proper function 3 Control of the electrical situation of the product Control cable bushing Control connection and plug Control controler unit 4 Control of the mechanic condition of the product Remove dirt and other uncleanliness Maintenance and assessment of the vital parts of the product Lubricate the product 5 Point 2 repeat control that everything is working properly Were there new problems in Point 5 If new problems emerge go back to point 2 If no problems were discovered you can finish the Attendance 5
6. dance cccccceeeseeeeeeeeeeeeeeeeeeeseeeeeeseneeees 8 5 2 FUSOS u na 9 5 3 Assessment Alround n n en en aeesnannann 9 9 4 Error Search na ee 10 6 Technical data ne 11 Platform Typus ae 11 Plator Typ A ernten entenen na Ea a PARRET TRETE AN TEARRE TEENA 11 1 In general 1 1 Producer Fa Lehner Lifttechnik G m b H A 4724 Neulirchen am Walde Salling 8 Tel 43 7278 3514 15 Fax 43 7278 3514 12 Mobil 0664 3526190 E mail office lehner gmx at www lehner lifttechnik at 1 2 Utilisation Utilisation The platform is produced for the utilisation inside and outside The platform can be used at temperatures of 20 up to 40 C At temperatures under 20 C we recommend the warming of the platform The platform is made for disabled persons who have to do height differences of 835 mm 1 6 stairs It is possible to drive in and drive out of the platform on every side In order to protect the user of the platform from falling of the platform the platform is equipped with a safety rail on both sides In order to protect the upper stop there is a rail which drives with the lift It is necessary to instruct the users and the assistants carefully 1 3 Important Warnings Please read the whole manual before the platform is operated The installation of the platform is only allowed by Lehner Lifttechnik or a qualified staff recommended by Lehner Lifttechnik The maximum load capacity of 180 kg mu
7. f Transformer 1 The connector of the transformer will be connected to the connector back at the plat form 2 The power plug has to be connected to the supply network system Put on the energy 1 6 Assembly disassembly fitting The disassembly of the platform and the fitting of the accessories are only allowed to be carried out by the company Lehner Lifttechnik or an approved qualified person The assembly has to be made according to the assembly manual The service staff gets the assembly manual either from the producer or the trader 2 Describtion of Operation 1 1 Label Company label with CE sign and fabric number placed on the platform Operation electric The manual operation can be mounted at the platform by the user of the platform Op eration buttons and the symbols are easy to understand Up Auf function from the bottom level 1 When the platform is on the bottom level and the access ramp is on the same level the wheelchair user can drive on the platform The rail that goes up with the platform is used as safety rail for the upper stop When you press the button Up AUF the access ramp drives upstairs and takes over the function of the safety rail Up AUF is not active as long as the button won t be pressed If the access ramp safety rail is in the upper position and Up AUF will be pressed furthermore the platform moves upstairs When the platform has reached the
8. hat they follow the edges of the bottom board of the platform Safety terminal strip If a person or an object will be jammed during the downward stroke of the platform the downward stroke stops immediately if the safety terminal strips will be activated In order to switch off the safety function the AUF Up button has to be pressed Now the object can be removed which has activated the safety terminal strip Emergency break The emergency break should only be activated in an emergency After using the emer gency break the platform should only be used again after consultation with the pro ducer trader The emergency break is located on a central place on the safety curbstone After using the emergency break all movements are stopped Turn the emergency break on the outside and after a short pressure on the Up Auf button the platform is operative again Emergency lowering device access ramp The access ramp is mounted with a bolt on the actuator This bolt will be screwed on an the access ramp opens Look at point 1 5 Important When the bolt of the access ramp is removed the access ramp is no longer mounted Therefore the access ramp has to be held when the bolt is removed User assistant emergency call system The function of the emergency system has to thought over for each use individually One or more responsible person s have to be educated in operating the platform right The responsible perso
9. ht swivel joint The disk will be mounted on the bush She must not be clamped The second disk will be mounted on the screw which will be mounted on the angle profile The nut will be mounted and screwed down screw it that it is fix 10 The nut on the safety cub described in point 5 will be screwed down fix Assembly of the access ramp of the actuator Attention Single components are correctly mounted at the delivery 1 2 3 The bush will be lubricated and placed on the actuator The disk will be mounted on the screw which will be mounted from the middle of the platform through the eye of the access ramp The 3 disks will be placed on the screw 4 The access ramp will be lifted up in a position in which the screw can be put through the bush of the actuator 5 A disk will be mounted on the screw 6 The nut will be screwed on 7 Lubricate the bottom and the fitting with oil or another lubricant Safety curb rail right actuator side 1 The assembly screws are pre assembled on the upper board They will be screwed off 2 The safety curb the rail will be mounted on the upper board The screws will be tightened End profile 1 Has to be mounted on the ends of the small safety curb Manual operation The manual operation will be put on the rail 1 The connector will be mounted in the connector bush in the safety curb 2 The manual operation will be screwed down and the connector is waterproo
10. n has to be available in every emergency situation The name of the responsible person has to be told the user We recommend a battery backup for the user which depend on the platform 3 Disassambly amp Transport 3 1 Transport It is possible to deconstruct the platfform for the transport and the keeping platform band ramp 3 2 Packing during the transport The company Lehner Lifttechnik recommends to transport the platform in the original packing 4 Attendance and keeping 4 1 Cleaning The lifting platform can be cleaned with a sponge or a brush and soap water The lifting platform can be hosed down with a normal water pressure but not with a pressure washer Acid base or solvent may not be used for cleaning 4 2 Keeping and storage No special requirements 4 3 How to prevent corrosion The lifting platform is made out of corrosion resist materials and therefore no corrosion protection is necessary 4 4 Which attendance has to be made by the owner Cleaning on demand 5 Attendance amp durability 5 1 Durability and attendance The platform has to be undergone an attendance at least once a year due to the na tional law The platform has a durability of about 10 years with regular daily use After this period the lifting platform has to be assessed by specialized staff in order to evaluate the fur ther application The durability is based to the conventional use a regular cleaning as well
11. st not be exceeded The platform is made for the transport of persons it is only allowed to use the plat form how it is described in the manual 1 4 Unpacking and preparation Visual controll If the packing is damaged at the receipt of the platform the parts of the platform have to be examined exactly if there are apparent damages or defects If there is suspect of damages the platform must not be used The platform has to be examined by the com pany Lehner Lifttechnik or qualified staff by Lehner Lifttechnik Tabel of content platform and safety curtain access ramp rail safety curb electric power supply application manual 1 5 Assembly before starting up Safety curb 1 rail actuator The assembly screws are pre assembled on the upper board They will be screwed off The safety curb the rail will be mounted on the upper board The screws will be tightened Fixing of the access ramp on the platform 1 2 3 T 8 9 Screws disks bush screw nuts which are on the swivel joint of the side access ramp will be removed A disk and a lubricated bush will be mounted on the let swivel joint The disk will be mounted on the bush She must not be clamped The second disk will be mounted on the screw which will be mounted through the bore of the safety curb The nut will be mounted and screwed down but not so fix A disk and a lubricated bush will be mounted on te screw which are mounted on the rig
Download Pdf Manuals
Related Search