Home

PM Series Matrix Router Owner`s Manual

1. Audio Matrix Volume Configuration Audio Matrix volume configuration commands are for the green block Audio Matrix Router 63 AV PureLink by Dtrovision Output Audio Volume Setting 1 0dB Step Attenuation The AV is an initiation command for Audio Matrix Router s Output Audio volume setting The characters and numbers that follow the AV command tell the system set Audio volume on desired Audio Matrix Router s Output The last character is found at the end of a command code which tells the system to execute the command AF For example the command code 255AVO001V01 O03V02 can be interpreted as follows Starting the command code 255 Router ID is 255 AV set Audio volume on Audio Matrix Router s Output on 001 Output 01 to V01 1 0dB 003 Output 03 to V02 2 0dB take the command For a complete list of command characters and their functions see examples below VOO O dB Attenuation V01 1 0dB Attenuation V02 2 0dB Attenuation V98 98 0dB Attenuation V99 Mute Example Command Codes Action 255AVALLVOO Set all Output volume to 0dB attenuation 255AVO01V01 O03V02 Set Output 1 0dB and Output3 2 0dB attenuation 255AVO01 09V99 Set Output1 9 to mute Output Audio Volume Status Request The AF is an initiation command for Audio Matrix Router s Output Audio volume information request The characters and numbers that follow the AF command tel
2. Operating Distance Up to 6 600 ft when used single mode Up to 1 650 ft when used multi mode Nominal Peak Wavelength 1310 and 1490 1550 nm Transmission Power gt 5 dBm typical Maximum Receiver Sensitivity lt 20 dBm typical Optical Loss Budget 10 dB Maximum Maximum Channel Data Rate 3 4 Gbps each channel Pixel Data Bit Depth 12 bits per channel 3 channel R G B Rise and Fall Times 20 80 Resolution Range Switching Speed 75psecs Rise time fall time 1080p 1920x 1200 50 60Hz Max 200ns HDCP Compatible HDCP version 2 0 Compatible Extenders PM FT101 PM FT102 PM FT103 PM FT101 D PM FT102 D PM FT101 RF6 PM FT102 RF6 PM FT101 RF6 D PM FT102 RF6 D Single Board Weight 1 5 Ibs 0 68 kg 17 3G HD SDI Input Board PM SIS4 PureLink by Dtrovision 3G HD SDI Input Board PM SIS4 Specifications Number of Port 4 3G HD SDI ports 4 Stereo In out ports Connector Type Audio Extraction Female BNC connector Female 3 5mm stereo jack Via 3 5mm stereo Audio out ports Audio Insertion Nominal Level Via 3 5mm stereo Audio in ports 0 8 Vp p 10 Impedance 75 ohm Return Loss lt 15 dB 1 MHz to 1 5 GHz Equalization Automatic or manual Input Cable Equalization Distance SDI 150m HD SDI 100m 3G HD SDI 50m DC Offset 0 5 mV with Input at 0 offset Re clockin
3. n nn nnn nnn nnn nnn nnn 33 3 4Cable Termination n nnn nn nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn 34 PureLink by Dtrovision Chapter 4 Operation 4 1 Front Panel Button Operation 37 4 2 RS 232 422 Command Line Operation 43 General Rules for Command Codes 44 Command Acknowledge Value Response 48 Connecting Switches 49 Disconnecting Switches 51 Connection Status Check 52 Input Board Function Configuration 53 Output Board Function Configuration 58 Audio Matrix Volume Configuration 64 Router ID Check n nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn nnn nmnnmnnnnn 65 Firmware Version Check nnn nnn nnn nnn nnn nnn 65 Baud Rate Setting nnn nnn nnn nnn 65 Network Configuration 6
4. Selected Output s display device s EDID information will be displayed Select Input where selected EDID data will be saved on to Multiple Input can be selected at once Push enter button to save 3 Int M EDID Load amp 4 Int S EDID Load On this menu select an EDID from the library and save it on to the Input EEPROM PM series Matrix Router has 14 selectable most widely used EDID data pre programmed and 4 empty slots that can be used to upload and save EDID data from any external display device Select EDID using ft arrow Select Input where selected EDID data will be saved on to Multiple Input can be selected at once Push enter button to save 5 Ext EDID Save On this menu user can emulate EDID data from any display devices that are connected to Matrix Router s Output via copper cables and save it on to the EDID library for future use 38 PureLink by Dtrovision e Select Output e Selected Output s display device s EDID information will be displayed e Select empty slot on EDID library where selected EDID data will be saved on to e Push enter button to save EDID status display o Write OK EDID save process was successfully completed o N C Not connected when Output Board or monitor are not installed or detected o Write Err Write error when EDID save process was not successfully completed 2 Router ID By setting different ID to the Matrix Router up to 255 units of PM series Matrix Router can be con
5. m L DVI Output Board PM DOS4 Specifications Number of Port 4 DVI ports 4 HDMI ports 4 Stereo In out ports Connector Type Female DVI connector Female HDMI connector Female 3 5mm stereo jack Signal Type RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Supported when HDMI signal source used Audio Extraction Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Maximum Data Rate 3 4 Gbps per color R G B Maximum Pixel Clock 165 MHz Standard DVI 1 0 HDMI 1 4 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Output Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible Support Hot Plug Detection Single Board Weight HDCP version 2 0 Yes 1 Ibs 0 45 kg 22 PureLink by Dtrovision DVI Output Board with Scaling PM DOS4S a a 2 n E a o a O Hitt OKO Hitt ORNL Be Be DVI Output Board with Scaling PM DOS4S Specifications Number of Port 4 DVI ports Connector Type Female DVI connector Signal Type RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Supported when HDMI signal source used Maximum Data Rate 3 4 Gbps per color R G B Maximum Pixel
6. 53 PureLink by Dtrovision Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 For example the command code 255IVIO1A 1I02M 103S can be interpreted as follows Starting the command code 255 Router ID is 255 IV Input Video selection on 101 Input 01 to A auto mode 102 Input 02 to M HDMI SDI 103 Input 03 to S DVI CATx Fiber take the command For a complete list of command characters and their functions see examples below Input Video Source Select A Auto M HDMI SDI S DVI CATx Fiber For HDMI Input Board only M HDMI can be selected For SDI Input Board only M SDI can be selected For DVI Input Board M HDMI or S DVI can be selected For CATx Input Board M HDMI or S CATx can be selected For Fiber Input Board M HDMI or S Fiber can be selected Example Command Codes Action 255 VALLM Set all Input source to HDMI SDI 255IVI01A 1I02M 103S Set Input 1 Auto Input 2 HDMI SDI Input3 DVI CATx Fiber 255 V101 09M Set Input1 9 to HDMI SDI Input Audio Source Select The IA is an initiation command for Input Audio selection The characters and numbers that follow the IA command tell the system which Input will be set to which Audio source The last character is found at the end of a command code which tells the system to execute the command For example the command code 255IAI01A 1I02M 103S
7. Fie stiri CCCCCCCCCCCCE C a Bapsed Remaining Throughput Connected 0 03 06 Auto detect 115200 8 N 1 NUM Firmware update completion window gt Once firmware update is completed disconnect USB cable and power cycle the unit OFF ON Set baud rate back to 19200 73 PureLink by Dtrovision 5 2 Manufacturer s Warranty 2 Year Dtrovision warrants this PM series Matrix Router to be free from defects in workmanship and materials under normal use and service for a period of five 5 years parts for PM series Matrix Routers and its I O Boards and three 3 years on labor from the date of purchase from Dtrovision or its authorized resellers If the product does not operate as warranted during the applicable warranty period Dtrovision shall at its option and expense execute one of the following as necessary 1 Repair the defective product or part 2 Deliver to customer and equivalent product or part to replace the defective item 3 Refund to customer the purchase price paid for the defective product All products that are replaced become the property of Dtrovision LLC Replacement products may be new or reconditioned Repaired or replacement products or parts come with a 90 day warranty or the remainder of the warranty period Dtrovision shall not be responsible for any software firmware information or memory data loss of contained in stored on or integrated with any products returned to Dtrovision for repair unde
8. 232 330 ft PM series DVI over CATx HDBaseT Extender Transmitter RF6 Rack mountable type DVI and VGA selectable Input dual 3 5mm Audio in POE RS 232 330 ft PM series HDMI over Fiber Optic Extender Transmitter Stand alone type HDMI Loop Through single 3 5mm Audio in RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Transmitter Stand alone type HDMI and VGA selectable Input dual 3 5mm Audio in RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Transmitter Wall Plate type HDMI and VGA selectable Input dual 3 5mm Audio in RS 232 6 600 ft 28 PM FT101 D PM FT102 D PM FT101 RF6 PM FT102 RF6 PM FT101 RF6 D PM FT102 RF6 D PM CR101 PM CR102 Note PM CR103 PM CR101 D PM CR102 D Note PM CR101 RF6 PM CR102 RF6 Note PM CR101 RF6 D PureLink by Dtrovision PM series DVI over Fiber Optic Extender Transmitter Stand alone type HDMI Loop Through single 3 5mm Audio in RS 232 6 600 ft PM series DVI over Fiber Optic Extender Transmitter Stand alone type HDMI and VGA selectable Input dual 3 5mm Audio in RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Transmitter RF6 Rack mountable type HDMI Loop Through single 3 5mm Audio in RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Transmitter RF6 Rack mountable type HDMI and VGA selectable Input dual 3 5mm Audio in RS 232 6 600 ft PM series DVI over Fiber Optic Extender Tran
9. 255 255 0 gate 192 168 0 1 Ethernet 1d 7d 7f b6 Press q or Q to exit TELNET vi i IP 192 168 0 3 mask 255 255 255 0 gate 192 168 0 1 Ethernet 6 1d 7d 7f Press q or Q to exit 9991000 255s Router ID 255 HTTP Protocol with LAN TCP IP 67 PureLink by Dtrovision Control PC Search Searching data for channel configuration Character train should begin with LCD CGI to O01 108 to Output 01 Input 8 The sequence and size of the character train must be the same To RESET the Protocol a new connection to the server Switcher must be established Switching Channels http 192 168 0 2 LCD CGI 001 101 amp 002 1028 amp 8003 103 amp 004 104 amp 005 1058 amp 006 106 amp 007 107 amp 008 108 amp Submit_ BERS RESET http 192 168 0 2 LCD CGI 001 101 amp 002 102 amp 003 103 amp 004 104 amp 005 105 amp 006 106 amp 007 107 amp 008 108 amp Submit_ RESE Control PC Transmission Information from each channel that needs to be sent must be extracted to prevent the entire Explore html data from being transmitted PM 16X File Edit View Favorites Tools Help H Favorites g Bs Purelink K Suggested Sites Web Slice Gallery PM 16X A D E amp Pager Safety Toos cas PM 16X LAN CONTROL Cross Platform Modular Matrix INPUT 01 01 00 00 00 01 00 00 00 00 00 00 00 00 00 00 OUTPUT 1 2 3 4 5 6 r 8 9 10 11 12 13 14
10. Output baud rate timing Output Audio volume control Audio Matrix Router s Output command this must precede AV Audio volume set 1 0db Output and volume step attenuation eit A specification Audio Matrix Router s Output AF Audio Matrix Router s Output Audio volume information Audio volume Information request command this must precede Output 0x49 Router ID check command l Router ID check check Router s current ID 0x69 i number f Firmware version check version Firmware version check command 255 version Baud rate sting command 255 001 19200 0x40 Baud rate setting 255 002 4 38400 255 003 4 57600 255 004 4 115200 Ox4E N Networking setting Network configuration setting 47 PureLink by Dtrovision Ox6E n command IP Setting 255NIP125 135 199 004 Subnet Mask Setting 255NSM255 255 255 000 Gate Way Setting 255NGW192 168 000 001 MAC Address Setting 255NMA00 50 C2 B0 20 05 Port Number Setting 255NPN3000 Network Information 255NNI000 Router communication Connection check connection check command 1 255HOOO Audio commands are for the independent green blocks Audio Matrix Router 0x48 H 0x68 h Command Ack Acknowledge Value Response When command codes are entered into a terminal emulation program such as HyperTerminal and are accepted by the system they respond back to the termi
11. PM FR101 RF6 PM FR102 RF6 27 PureLink by Dtrovision PM FR101 RF6 D PM FR102 RF6 D PM CT101 PM CT102 PM CT103 PM CT101 D PM CT102 D PM CT101 RF6 PM CT102 RF6 PM CT101 RF6 D PM CT102 RF6 D PM FT101 PM FT102 PM FT103 PM series HDMI over CATx HDBaseT Extender Transmitter Stand alone type HDMI Loop Through single 3 5mm Audio in POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Transmitter Stand alone type HDMI and VGA selectable Input dual 3 5mm Audio in POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Transmitter Wall Plate type HDMI and VGA selectable Input dual 3 5mm Audio in POE RS 232 330 ft PM series DVI over CATx HDBaseT Extender Transmitter Stand alone type DVI Loop Through single 3 5mm Audio in POE RS 232 330 ft PM series DVI over CATx HDBaseT Extender Transmitter Stand alone type DVI and VGA selectable Input dual 3 5mm Audio in POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Transmitter RF6 Rack mountable type HDMI Loop Through single 3 5mm Audio in POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Transmitter RF6 Rack mountable type HDMI and VGA selectable Input dual 3 5mm Audio in POE RS 232 330 ft PM series DVI over CATx HDBaseT Extender Transmitter RF6 Rack mountable type DVI Loop Through single 3 5mm Audio in POE RS
12. This section is designed for programmers who wish to create their own control programs using the command code All PureLink digital Matrix Routers provide a simple character stream control used by external control devices attached to a PureLink device Command codes are used primarily for control during system installation and setup and for diagnostic purposes Command code is a set of alphanumeric characters that combine to form control commands Command code strings are entered into a terminal emulation program such as windows HyperTerminal running on an external control device The control device PC third party controller sends the commands to the system Control devices must be able to send and receive ASCII or HEXA code via an RS 232 or Ethernet port Command Code Formats A command code is a series of command characters and numbers used to send commands to the system Commands include basic formulas for creating and disconnecting switches as well as for verifying the status of switches and other functions In a command code each character is either general command e g C for connect or an identifier that indicates what the following number designates e g O and the number following it designate an Output number The command code 255C101001 Can be interested as follows Starting the command code 255 Router ID is 255 C Create connection on 101 Input 01 to 001 Output 01 take the command For a complete lis
13. baud rate at 19200 255 002 Set baud rate at 38400 255 003 Set baud rate at 57600 255 004 Set baud rate at 115200 Network Configuration User can check and set network configuration for LAN control Examples Command Codes Action 255NNI000 Check current Network Information 209NIP192 168 000 004 Set IP address at 125 135 199 004 299NSM255 255 255 000 Set Subnet Mask at 255 255 255 000 209NGW192 168 000 001 Set Gate Way at 192 168 000 001 259NMA00 00 C2 B0 20 05 Set Mac Address at 00 00 C2 B0 20 05 255NPN3000 Set Port Number at 3000 Connection Checking User can check the connection status Example Command Codes Action 255H000 4 Check connection status Front Panel Touch Screen Security Lock Unlock User can enable or disable the front panel touch screen Example Command Codes Action 255KST 4 Touch Lock Status Return 255KON Touch Lock On 255KOFF Touch Lock Off 4 3LAN TCP IP Operation TELNET Protocol with LAN TCP IP 66 PureLink by Dtrovision The PM series Matrix Router can be controlled from remote locations through the LAN port using WINDOWS XP DOS prompts hyper terminal or TELNET program TELNET v1 61 IP 192 168 0 3 mask 255 255 255 gate 192 168 0 1 Ethernet 1d 7d 7f b6 a8 Press q or Q to exit Q C W gt TELNET 192 168 000 002 TELNET vi i IP 192 168 0 3 mask 255
14. can be interpreted as follows Starting the command code 255 Router ID is 255 IA Input Audio selection on 101 Input 01 to A auto mode 102 Input 02 to M Embedded Audio 103 Input 03 to S 3 5mm stereo Audio take the command For a complete list of command characters and their functions see examples below 54 PureLink by Dtrovision Input Audio Source Select A Auto M Embedded Audio S 3 5mm Stereo Audio M Embedded Audio refers to embedded Audio from the HDMI source or inserted Audio from Extender Transmitter for CATx and Fiber Input Boards S 3 5mm stereo Audio refers to inserted Audio from Input Board s 3 5mm stereo jack Example Command Codes Action 255IAALLS Set all Input Audio to 3 5mm stereo Audio 255IAI01A 1I02M 103S Set Input 1 auto Input 2 embedded and Input 3 3 5mm stereo Audio 255IAI01 09M Set Input1 9 to embedded Input Video Preview Monitoring Select The IM is an initiation command for Input monitoring selection The characters and numbers that follow the IM command tell the system which Input Video to be Output P is found at the end of a command code which tells the system to execute the command to preview monitoring port The last character For example the command code 255IMI02 can be interpreted as follows Starting the command code 255 Router ID is 255 IM Input monitoring selection on 102 Input 02 take t
15. process can begin Installing and Removing Input and Output Board z ee mammmmmamaRaN SSS SSS RS SPF Pee Seeeeeaeeenaaa BABA BBSBSSSSESS PM 8X has total 4 horizontal Board slots 2 Input Board slots section on the top side and 2 Output Board slots section on the middle side to configure maximum of 8 Inputs and 8 Outputs Input 1 2 3 4 Output 1 2 3 4 Input 5 6 7 8 Output 5 6 7 8 Install Board as follows 1 Align the Board with metal guide rail 2 Gently slide the Board into the frame until it connects to the main frame 3 Tighten the left and right screw knobs clockwise to lock the Board to the main frame Removing Board as follows 1 Disconnect any connected cables 2 Loosen and pull the left and right screw knobs counterclockwise to unlock the Board from the main frame 3 Gently slide Board out of the main frame Installing the Matrix Router in a Rack Note When mount the Matrix Router in a rack ensure that none of the fans have restricted air flow 32 PureLink by Dtrovision PM 8X is designed to be mounted in a standard 19 48 26 cm AV rack It takes 3 RU rack space and it is recommended to have at least one empty rack unit space above and below of the Matrix Router to prevent overheating Rack Installation Tips e Write down the serial number usually located on the bottom of the unit in an easily accessible location prior to installing the unit in a rack e It is recommen
16. the next data section Please use Enter button to save the setting Note Please contact your Network Administrator for network information to avoid any IP conflict Factory default settings for LAN communication are IP Address 192 168 000 002 Gateway Address 192 168 000 001 Subnet Mask 255 255 255 000 Mac Address Matrix Router has its own MAC address and that MAC address allows user to communicate with PC network solutions without any communication conflict 5 Input Configuration 1 Input Video Select 2 Input Audio Select 40 PureLink by Dtrovision Some of the configuration applies to certain Input Board type only For example HDMI Input Board does not need to configure Video because there are no choices to make First select Input that wishes to make a change on Input section and then configure setting using Create UP Preview Down and Enter buttons 6 Output Configuration 1 Output M Audio Select 2 Output S Audio Select It displays current Output Board s Audio configuration Only Audio option can be configured on Output Boards First select Output that wishes to make a change on Output section and then use M Audio HDMI SDI and S Audio CATx Fiber section for configuration Use Create UP Preview Down and Enter buttons for setting configuration 7 Test Pattern PM series Matrix Router provides a built in Test Pattern Generator enabling easy testing from the Matrix Router to the display Use Cr
17. 00 004 19200 005 38400 006 57600 007 76800 008 115200 For example the command code 255IP101 001 type code 1 lt Please note that there should be two carriage return for this 255IPC specific command string the one right after the and the last one should go after the closing quotation mark No space in between gt can be interpreted as follows Starting the command code 255 Router ID is 255 IP Input Extender command transmission on 101 Input 01 Extender 001 at baud rate 4800 take the command Once communication port is open command 21 89 01 50 57 30 OA OD can be sent After receiving feedbacks from AV devices close the port 255IPC For a complete list of command characters and their functions see examples below Example Command Codes Action 255IP101 001 Open communication port with a device that is connected to Input 1 Extender at 9400 bps baud rate lO01 abcdefge Send command abcdefg to Input 1 255 IPC Close communication port 57 PureLink by Dtrovision 255 IPI02 O6 004 Open communication port with devices that are connected to Input 2 6 Extender at 19200 bps baud rate 255 IPI05 004 1I07 008 Open communication port with devices that are a connected to Input 5 at 19200 bps baud rate and Input 7 at 115200 bps baud rate IALL pme 4 Send command pm to all open ports l02 purelink Send command purelink to In
18. 05 255DI00003 06 Disconnects both Video and Audio Outputs 3 4 and 5 Disconnects both Video and Audio Output 3 4 5 and 6 255DALLIO Disconnects both Video and Audio all Inputs and Outputs Examples Disconnect Video only Command Codes Action 255VDI01000 Disconnect Video Input 1 to no Output 00 255VDI00003 04 05 Disconnects Video Outputs 3 4 and 5 255VDI00003 06 Disconnects Video Output 3 4 5 and 6 255VDALLIO Disconnects Video all Inputs and Outputs Examples Disconnect Audio only Command Codes Action 255ADI01000 lt Disconnect Audio Input 1 to no Output 00 255ADI00003 04 05 255ADI00003 06 255ADALLIO Disconnects Audio Outputs 3 4 and 5 Disconnects Audio Output 3 4 5 and 6 Disconnects Audio all Inputs and Outputs Connection Status Check A connection status can be checked to confirm that the switch has been correctly executed or to confirm correct routing to multiple Outputs The characters and numbers in a status command tell the system which Input or Output to check To check connection status Enter the Connection status check command below Replace the s with the Input and Output number s 52 PureLink by Dtrovision 255 1 Cor 255 0 Note For PM 128X and PM 256X input and output uses three digit format instead of two dig
19. 16 16 PURELINK G Internet Protected Mode Off fa vy R10 v a om z 6235PM ts al E 8 EN eD Z2 Run Explorer and enter the newly configured IP address to open the channel configuration window above Select desired channel and click SEND to change the channel 68 PureLink by Dtrovision Chapter 5 Additional Information 5 1 Firmware Update Instruction 1 Set PM series Matrix Router s baud rate to 115200bps using front panel LCD touch screen or control command Data bits 8bit Stop bits 1bit Parity disable 2 Connect PC to PM series Matrix Router using USB cable update cable is included in an original box v Please disconnect RS 232 cable from the Matrix Router during firmware update Confirm if PM series Matrix Router USB serial port is properly connected to the PC on PC s device manager section E Device Manager File Action View Help ese m fS B BEA RAa DTROVISIONUPS 3 Computer Se Disk drives E 2 Display adapters Floppy disk controllers gj Human Interface Devices IDE ATA ATAPI controllers jp IEEE 1394 Bus host controllers Jungo Keyboards Mice and other pointing devices E Monitors Network adapters Y Ports haart MR Processors Sound video and game controllers Storage volumes o System devices Universal Serial Bus controllers 3 Create a hyper terminal connection connect it using same com port number COM1 e Cr
20. 4 Stereo In out ports Connector Type Audio Insertion Female BNC connector Female 3 5mm stereo jack Via 3 5mm stereo Audio in ports Nominal Level 0 8 Vp p 10 Impedance 75 ohm Return Loss lt 15 dB 1 MHz to 1 5 GHz Equalization Automatic or manual Output Cable Equalization Distance SDI 150m HD SDI 100m 3G HD SDI 50m DC Offset 0 5 mV with Input at O offset Re clocking Automatic Jitter lt 0 3 Ul Rise and fall times 20 80 135psecs Rise time fall time 2970Mbps Maximum data rate 2 97 Gbps Auto Data Rate Lock Yes Data Types 8 bits or 10 bits Operation Standard SMPTE 292M SMPTE 259M SMPTE 424M ITU RBT 601 ITU RBT 1120 Single Board Weight 1 5 Ibs 0 68 kg 26 PureLink by Dtrovision 2 5 PM Matrix Boards and PM Extenders Compatibility Chart Boards Extenders PM CIS4 PM FIS4 PM COS4 PM FOS4 PM CT101 PM CT102 PM CT103 PM CT101 D PM CT102 D PM CT101 RF6 PM CT102 RF6 PM CT101 RF6 D PM CT102 RF6 D PM FT101 PM FT102 PM FT103 PM FT101 D PM FT102 D PM FT101 RF6 PM FT102 RF6 PM FT101 RF6 D PM FT102 RF6 D PM CR101 PM CR102 PM CR103 PM CR101 D PM CR102 D PM CR101 RF6 PM CR102 RF6 PM CR101 RF6 D PM CR102 RF6 D PM FR101 PM FR102 PM FR103 PM FR101 D PM FR102 D
21. 6 Connection Checking nnn nn nn nnn nnn nnn 66 Front Panel Touch Screen Security Lock Unlock 66 4 3 LAN TCP IP Operation nnn nnn nnn nnn nnn nnn 67 Telnet Protocol with LAN TCP IP 67 HTTP Protocol with LAN TCP IP 68 Chapter 5 Additional Information 5 1 Firmware Update Instruction 70 5 2 Warranty nan nn nn nnn nnn nr nn nnn 75 PureLink by Dtrovision Chapter 1 Introduction 1 1 Safety Precautions When using and installing Dtrovision PureLink product adhere to the following basic safety precautions e Read and understand all instructions before using and installing this product e The safety and operating instructions should be retained for future reference e Always use the correct external power supply indicated on the product label when operating this unit e Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning e Mishandling of this product may lead to a fire or explosion hazard e Do not place any heavy objects or equipment on top of the product e Keep away from wet magnetic and flammable surfaces or substances e Air vents should be kept clean and unobstr
22. Board PM CIS4 Specifications Number of Port 4 CATx ports 4 HDMI ports 4 Stereo In out ports Connector Type Female RJ45 connector CAT5 5e CAT6 6e CAT6a CAT7 Supported Twisted Cable Type Female HDMI connector Female 3 5mm stereo jack Digital Audio Supported when HDMI signal source used Audio Extraction Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Supported Twisted Pair Cable Length 330 ft 100m 1080p 1920x1200 50 60Hz P O E Maximum Output Watt Max 9 6Watt per channel Resolution Range 1080p 1920x 1200 50 60Hz Maximum Data Rate 3 4 Gbps per color R G B Switching Speed Max 200ns HDCP Compatible HDCP version 2 0 Compatible Extenders PM CT101 PM CT102 PM CT103 PM CT101 D PM CT102 D PM CT103 D PM CT101 RF6 PM CT102 RF6 PM CT101 RF6 D PM CT102 RF6 D Single Board Weight 1 Ibs 0 45 kg 16 Fiber Optical Input Board PM FIS4 PureLink by Dtrovision Fiber Optical Input Board PM FIS4 Specifications Number of Port 4 Optical ports 4 HDMI ports 4 Stereo In out ports Connector Type Female 2 LC connector Female HDMI connector Female 3 5mm stereo jack Mode Type Supports both single mode amp multi mode Digital Audio Supported when HDMI signal source used Audio Extraction Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports
23. Brown White TMDS Clock 12345678 8 Brown TMDS Clock RS 232 422 Cable Termination for Control Note Crossover Null modem cable must be used for the communication with PM series Matrix Router The following table shows the pinout of the RS 232 422 connector Note that in the pinout table some transmit receive functions abbreviated as Tx Rx are different for RS 232 34 PureLink by Dtrovision versus RS 422 DB9 cables are available with male to male female to female and male to female connectors PM series Matrix Router s RS 232 422 port uses a male DBY connector and therefore requires a cable with a female connector Pin RS 232 RS 422 1 Not used Not used 2 Rx Receive Rx Receive 3 Tx Transmit Tx Transmit 4 Not used Not used 5 Ground Ground 6 Not used Not used 7 Not used Tx Transmit 8 Not used Rx Receive 9 Not used Not used LAN Cable Termination for Control The following table shows the pinout of the LAN connector Note that in the pinout table some transmit receive functions abbreviated as Tx Rx are different for straight through cable and crossover LAN cable Straight through Cable for connection of PM series Matrix Router to an Ethernet network Crossover Cable for direct connection between the PC or controller and the PM series Matrix Router Crossover Cable Pin End 1 Wi
24. Clock 165 MHz Standard DVI 1 0 HDMI 1 3 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Output Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible HDCP version 2 0 Support Hot Plug Detection Yes Single Board Weight 1 Ibs 0 45 kg 23 PureLink by Dtrovision CATx HDBaseT Output Board PM COS4 CATx HDBaseT Output Board PM COS4 Specifications Number of Port 4 CATx ports 4 HDMI ports 4 Stereo In out ports Connector Type Female RJ45 connector Supported Twisted Cable Type Female HDMI connector Female 3 5mm stereo jack CAT5 5e CAT6 6e CAT6a CAT7 Digital Audio Audio Extraction Supported when HDMI signal source used Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Supported Twisted Pair Cable Length 330 ft 100m 1080p 1920x1200 50 60Hz P O E Maximum Output Watt Max 9 6Watt per channel Resolution Range 1080p 1920x 1200 50 60Hz Maximum Data Rate 3 4 Gbps per color R G B Switching Speed Max 200ns HDCP Compatible HDCP version 2 0 Compatible Extenders PM CR101 PM CR102 PM CR103 PM CR101 D PM CR102 D PM CR101 RF6 PM CR102 RF6 PM CR101 RF6 D PM CR102 RF6 D Single Board Weight 1 Ibs 0 45 kg Note Scaling Receiver PM CR102 does not support POE 24 Fiber Optical
25. Easy Firmware Update using USB port in the rear panel no software program required Three Convenient Control Methods Control via front panel touch screen Control via RS 232 422C Control via LAN TCP IP Maximum Distance up to 6 600ft As part of a complete switching system send Audio Video control signal and power up to 330ft over single CATx cable to and from the PM Matrix Router using PM series CATx Extenders and send Audio Video and control signal up to 6 600ft over Fiber Optic cable to and from the PM Matrix Router using PM series Fiber Extenders 11 PureLink by Dtrovision gt Plug N Play gt Standard 19 Rack mountable e PM 8X 3 RU gt Resolutions up to WUXGA 1920x1200 HD 1080p 60Hz and 4K2K Optional gt Integrated Noise cancellation and Error correct Logic for both Input and Output Ports to prevent any damage caused by Electrical Noise 2 2 Router Frame Specification PM 8X _ Homi Eli 36 SDI DBT PM 8X B 8x8 Cross Platform Modular Matrix Router y ae Sar 7 2S eee SOTO seem em eee eee BRS SSSA S SSAA ganana Cees sees eee eee eee WR RRS PM 8X Frame General Specifications Maximum of Input Board load 2 of any kind of Input Board Available Input Board HDMI DVI 3G HD SDI VGA Component CATx HDBaseT Fiber Optic Maximum of Output Board load 2 of any kind of Output Board Available Output Board HDMI HDMI w scaling DVI DVI w scaling 12 PureL
26. Flexible Input Output Switching with Auto Distribution Each main port on the PM series DVI CATx and Fiber I O Boards also contains a parallel HDMI port effectively doubling those Boards I O capacity On the Input Side the user can select either the main CATx DVI Fiber port or the parallel HDMI port via the front panel or control command providing a 2x1 switch within the Input and thereby double the amount of Inputs On the Output side the main DVI CATx and Fiber port and the parallel HDMI are driven simultaneously providing a 1x2 distribution amplifier with a mirrored Output for each main Output Audio Insertion Extraction Every Video port on the PM series Matrix Router I O Boards also provides a 3 5mm Stereo Audio Input and Output enabling easy extraction of 2 channel PCM Audio from HDMI or Audio from PM Extender Transmitter as well as insertion of a separate 2 channel Audio signal onto HDMI CATx and Fiber Outputs Audio Matrix Router PM series Matrix Router frame offers independent built in Balanced Unbalaned Audio Matrix Router Depending on the frame size it comes as a standard feature and some of them are optional PM 8X AD Optional Internal 8x8 Audio Matrix Router for PM 8X Audio Attenuation and Muting Every PM series Matrix Router allows volume attenuation and muting on the Audio Matrix Router s Output Test Pattern Generator Every PM series Matrix Router provides a built in Test Pattern Generator enabling easy te
27. M FR103 PM FR101 D PM FR102 D PM FR101 RF6 PM FR102 RF6 PM FR101 RF6 D PM FR102 RF6 D PureLink by Dtrovision PM series DVI over CATx HDBaseT Extender Receiver RF6 Rack mountable type Built in Scaler single 3 5mm Audio out POE RS 232 330ft Scaling Receiver PM CR102 RF6 D does not support POE PM series HDMI over Fiber Optic Extender Receiver Stand alone type Single 3 5mm Audio out RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Receiver Stand alone type Built in Scaler single 3 5mm Audio out RS 232 6 600ft PM series HDMI over Fiber Optic Extender Receiver Wall Plate type Single 3 5mm Audio out RS 232 6 600ft PM series DVI over Fiber Optic Extender Receiver Stand alone type Single 3 5mm Audio out RS 232 6 600 ft PM series DVI over Fiber Optic Extender Receiver Stand alone type Built in Scaler single 3 5mm Audio out RS 232 6 600ft PM series HDMI over Fiber Optic Extender Receiver RF6 Rack mountable type Single 3 5mm Audio out RS 232 6 600 ft PM series HDMI over Fiber Optic Extender Receiver RF6 Rack mountable type Built in Scaler single 3 5mm Audio out RS 232 6 600ft PM series DVI over Fiber Optic Extender Receiver RF6 Rack mountable type Single 3 5mm Audio out RS 232 6 600 ft PM series DVI over Fiber Optic Extender Receiver RF6 Rack mountable type Built in Scaler single 3 5mm Audio out RS 232 6 600ft 30 PureLink by Dtrovision 3 1 Package Conten
28. Output Board PM FOS4 PureLink by Dtrovision Fiber Optical Output Board PM FOS4 Specifications Number of Port 4 Optical ports 4 HDMI ports 4 Stereo In out ports Connector Type Female 2 LC connector Female HDMI connector Female 3 5mm stereo jack Mode Type Supports both single mode amp multi mode Digital Audio Supported when HDMI signal source used Audio Extraction Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Operating Distance Up to 6 600 ft when used single mode Up to 1 650 ft when used multi mode Nominal Peak Wavelength 1310 and 1490 1550 nm Transmission Power gt 5 dBm typical Maximum Receiver Sensitivity lt 20 dBm typical Optical Loss Budget 10 dB Maximum Maximum Channel Data Rate 3 4 Gbps each channel Pixel Data Bit Depth 12 bits per channel 3 channel R G B Rise and Fall Times 20 80 Resolution Range Switching Speed 75psecs Rise time fall time 1080p 1920x 1200 50 60Hz Max 200ns HDCP Compatible HDCP version 2 0 Compatible Extenders PM FR101 PM FR102 PM FR103 PM FR101 D PM FR102 D PM FR101 RF6 PM FR102 RF6 PM FR101 RF6 D PM FR102 RF6 D Single Board Weight 1 5 Ibs 0 68 kg 25 3G HD SDI Output Board PM SOS4 PureLink by Dtrovision 3G HD SDI Output Board PM SOS4 Specifications Number of Port 4 3G HD SDI ports
29. PROGRAM MODE EXIT ll rote p imwareflesWRTWPM Femwaret PM Fame Filename 1 Firmware WPM Frame WPM I6X MCU V230 r0n Browse Protocol _ Ymodem iy x Application Program Wait ROM file a A eens CCCCCCCCCCCCCCCCCCCCCC Connected 0 03 06 Auto detect 115200 8 N 1 RO CA NUM 72 PureLink by Dtrovision 8 Select firmware file rom and then gt Send S program JE HE JE HE JE JE JE HE FE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE EE EE MATRIX SOFTWARE PROGRAM MODE RIT Sen 271 Enter key Push OUTPUT SLOT f Send File PROGRAM MODE EXIT p Folder P 4Fimware files RT WPM FimwaretPM Frame Filename 1 Fimware WPM FrameWPM 16X MCU V2 20 0n Browse Protocol 3 Application Program Ymodem x Wait ROM file a Ab sena cose canca ae CCCCCCCCCCCCCCCCCCCCCC Connected 0 03 06 Auto detect 115200 8 N 1 L gt NUM 9 Firmware update progress window e i ag Dg PE aD program MATRIX SOFTWARE PROGRAM MODE MATRIX MAIN Ymodem file send for PM 16X J Z OUTPUT SLOT aE PROGRAM MODE EXIT 749 eats RE RGisey iaeena pee eee re Packet Eror checking CRC File size 485K 1 Reties 0 Total retries 0 Files 1 of 1 System BootLoad Runni Application Program Last eror Wait ROM file a Ab CCCCCCCCCCCCCCCCCCCCCCC
30. Protocols are communicated through RS 232 422 LAN or front panel touch screen USB connection is only for firmware update e Make sure any connected Extenders power are on CATx Extenders may not need power if they will be powered via POE e Turn on the power of display devices e Turn on the power of Matrix Router e Turn on the power of source devices 33 PureLink by Dtrovision Note For most of cases PureLink s Auto EDID factory default setting will result in a satisfactory image on the display It s almost plug n play system There may be cases where additional adjustment is required please refer to Auto EDID management system section pg 63 or contact PureLink technical support team for the assistance 3 4 Cable Termination e CATx HDBaseT cable e RS 232 422 cable PM Matrix e LAN cable e Audio cable e RS 232 422 cable PM Extenders CATx Cable Termination for CATx Input Output Boards PM series Matrix Router and Extenders are designed TIA EIA 566 B Standard Please ensure that each PIN layout of the cable is corresponding with the picture below before connecting the cable Please note that CATx or above level cable enables to deliver better quality and longer distance TIA EIA 568B Signal Pin Wire color Digital RGB 1 Orange White TMDS Data2 2 Orange TMDS Data2 3 Green White TMDS Data1 4 Blue TMDS Data0 5 Blue White TMDS Data0 6 Green TMDS Data1 7
31. SDI Input Board 18 PM AIS4 Analog VGA Component Input Board 19 2 4 Output Board Specifications 20 PM HOS4 HDMI Output Board 20 PM HOS4S HDMI Output Board w Scaling _ 21 PM DOS4 DVI Output Board _ 22 PM DOS4S DVI Output Board w Scaling _ 23 PM COS4 CATx HDBaseT Output Board _ 24 PM FOS4 Fiber Output Board 25 PM SOS4 3G HD SDI Output Board 26 2 5 PM Matrix Boards and PM Extenders Compatibility Chart 27 Chapter 3 Installation 3 1 Package Contents n ne 31 3 2 Installation Environments 22 nana nn nn nnn nnn nnn nnn nnn nnn 31 3 31NStallatioN nn nnn nn nn nn nn nn nn nnn nnn nnn nnn nme nnnnn 32 a Installing and Removing Input and Output Board _ 32 b Installing the Matrix Router in a Rack 32 c Installation and Setup
32. a PureLink PM Series Matrix Router Owner s Manual ee 36 SDI DBT bs E 5 a3 a nnannenn PM 8X TP 8x8 Cross Platform Modular Matrix Router PM 8X PM 8 x 8 Cross Platform Modular Matrix Router PureLink 535 East Crescent Ave For Technical Support contact us at Ramsey NJ 07446 support purelinkav com Tel 201 488 3232 Fax 201 621 6118 Website www purelinkav com E mail info purelinkav com PureLink by Dtrovision TABLE OF CONTENTS Introduction 1 1 Safety Precautions nn nnn nnn nnn nnn nnn nnn nnn nn nn nnn mmmn 4 1 2 Product Introduction nnn enn mentee 5 1 3 Front View n 2 n nn nnn nm nania 5 1 4 Rear View n ne nnn nnn nnn nn nn aaa 6 ter 2 Features and Specifications 2 1 Features nnn n ne n nnn nnn nnn nen mene mene nnn nnnmnnnnnnnmnnannnnnennnnenn 8 2 2 Router Frame Specifications 12 2 3 Input Boards Specifications nnn nnn 14 PM HIS4 HDMI Input Board 14 PM DIS4 DVI Input Board a nn 15 PM CIS4 CATx HDBaseT Input Board 16 PM F1S4 Fiber Input Board nn nn nnn 17 PM SIS4 3G HD
33. and 3 255VC101001 07 Connect Video Input 1 to Output 1 2 3 4 5 6 and 7 Examples for PM 128X and PM 256X Connect Video only Command Codes Action 255VC10010001 Connect Video Input 1 to Output 1 255VC10010008 10080002 Connect Video Input 1 to Output 8 and Input 8 to Output 2 255VC10010001 10020002 10 Connect Video Input 1 to Output 1 Input 2 to Output 2 and 50 PureLink by Dtrovision 030003 Input 3 to Output 3 255VC10010001 002 003 Connect Video Input 1 to Output 1 2 and 3 255VC10010001 007 Connect Video Input 1 to Output 1 2 3 4 5 6 and 7 Examples Connect Audio only Command Codes Action 259ACI01001 Connect Audio Input 1 to Output 1 259ACI01008 108002 Connect Audio Input 1 to Output 8 and Input 8 to Output 2 255ACI01001 I02002 103003 Connect Audio Input 1 to Output 1 Input 2 to Output 2 and ae Input 3 to Output 3 259ACI01001 02 03 Connect Audio Input 1 to Output 1 2 and 3 2559ACI01001 07 Connect Audio Input 1 to Output 1 2 3 4 5 6 and 7 Examples for PM 128X and PM 256X Connect Audio only Command Codes Action 250ACI0010001 Connect Audio Input 1 to Output 1 255ACI0010008 10080002 Connect Audio Input 1 to Output 8 and Input 8 to Output 2 255ACI0010001 10020002 10 Connect Audio Input 1 to Output 1 Input 2 to Ou
34. both Video and Audio Input 1 to Output 1 255C101008 108002 Connect both Video and Audio Input 1 to Output 8 and Input 8 to Output 2 255C101001 102002 103003 4 Connect both Video and Audio Input 1 to Output 1 Input 2 to Output 2 and Input 3 to Output 3 255C101001 02 03 255C101001 07 Connect both Video and Audio Input 1 to Output 1 2 and 3 Connect both Video and Audio Input 1 to Output 1 2 3 4 5 6 and 7 Examples for PM 128X and PM 256X Connect Video and Audio Command Codes Action 255C10010001 Connect both Video and Audio Input 1 to Output 1 255C10010008 10080002 Connect both Video and Audio Input 1 to Output 8 and Input 8 to Output 2 255C10010001 10020002 1003 o003 Connect both Video and Audio Input 1 to Output 1 Input 2 to Output 2 and Input 3 to Output 3 255C10010001 002 003 Connect both Video and Audio Input 1 to Output 1 2 and 3 255C10010001 007 Connect both Video and Audio Input 1 to Output 1 2 3 4 5 6 and 7 Examples Connect Video only Command Codes 255VCl01001 4 255VCl01008 108002 Action Connect Video Input 1 to Output 1 Connect Video Input 1 to Output 8 and Input 8 to Output 2 255VC101001 102002 103003 ya Connect Video Input 1 to Output 1 Input 2 to Output 2 and Input 3 to Output 3 255VC101001 02 03 Connect Video Input 1 to Output 1 2
35. creen 2 RS 232 422C 3 LAN TCP IP 4 1Front Panel Button Operation Turn the power switch on Once all channel indicator lights are on the first step is completed Channel View and Input Output Selection e IN OUT indicates connection status e Press the IN OUT KEY to display each channel s connection status and video resolution e Press the CANCEL KEY to return to the initial screen Create Menu e Select an INPUT channel e Press the OUT buttons to set a channel e Press the ENTER button to save or switch input channels e Press CANCEL to reverse a selection and return to the previous screen Function Select a FUNCTION button to view the sub menu Use the Create UP Preview Down buttons to control the sub menu options On the sub menu user can check and configure below settings 1 EDID 2 Preset 3 Product ID 4 RS232 5 LAN 6 Input Configuration 7 Output Configuration 8 Test Pattern 9 Monitoring Out 37 PureLink by Dtrovision 10 Firmware Version 11 Factory Reset 1 EDID 1 Ext M EDID Load Ext S EDID Load 3 Int M EDID Load Int S EDID Load 1 Ext M EDID Load amp 2 Ext S EDID Load This menu is to emulate EDID data from any display devices that are connected to the Matrix Router s Output via copper cables and save it on to Matrix Router s Input EEPROM v For CATx and Fiber Output Boards EDID emulation is not possible In this case try EDID library feature v Select Output
36. cture quality LCD Touch Screen Display w Security Lock Out Every PM series Matrix Router has front panel LCD Touch Screen for intuitive operation Security Lock Out feature prevents unauthorized user to access to the Matrix Router In lock out mode a password entered from the touch screen or special command sent from controller can disable the lock out mode Auto EDID EDID Library Emulation PureLink s EDID library and emulation features failsafe EDID capture amp storage to provide constant and continuous EDID for source devices 10 PureLink by Dtrovision Various Input Output Choices There are five Input Board types and six Output Board types to support every conceivable digital Video format HDCP Compliant Modular Field upgradeable PM Matrix Router is designed to expand upgrade and reconfigure the Matrix Router in the field by simply installing or replacing Input Output Board Preset Multiple preset switching commands can be pre programmed and saved in the memory It can be recalled in the future for easy and time saving switching use Analog Support VGA and Component PM Matrix Router supports analog VGA and component signal via PM Extender Transmitters Fan Power Supply Monitoring PM Matrix Router provides real time fan power supply units status on the front panel LCD touch screen PM Universal Input Output Boards PM Input Output Boards can be used in any size of PM Matrix Router frame USB Firmware Update
37. dard DVI 1 0 HDMI 1 4 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Input Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible HDCP version 2 0 Support Hot Plug Detection Yes Single Board Weight 0 5 Ibs 0 23 kg 14 DVI Input Board PM DIS4 PureLink by Dtrovision DVI Input Board PM DIS4 Specifications Number of Port 4 DVI ports 4 HDMI ports 4 Stereo In out ports Connector Type Signal Type Female DVI connector Female HDMI connector Female 3 5mm stereo jack RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Audio Extraction Supported when HDMI signal source used Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Maximum Data Rrate 3 4 Gbps per color R G B Maximum Pixel Clock 165 MHz Standard DVI 1 0 HDMI 1 4 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Input Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible Support Hot Plug Detection Single Board Weight HDCP version 2 0 Yes 1 Ibs 0 45 kg 15 CATx HDBaseT Input Board PM CIS4 PureLink by Dtrovision CATx HDBaseT Input
38. ded to test unit to ensure the unit is working properly prior to installing the unit in a rack e For HDMI or DVI Input and or Output Boards we recommend to use copper cable no longer than 33 ft 10meters for HD Video quality assurance Above 33 ft 10meters we recommend to use CATx or Fiber Optic extension system This will assure future with higher resolution Video transmission e For CATx Input and or Output Boards PM CATx Extenders are required PM CATx Transmitters pair with PM CATx Input Board and PM CATx Receivers pair with PM CATx Output Board See pg 35 for detail information e For Fiber Input and or Output Boards PM Fiber Extenders are required PM Fiber Extender Transmitters pair with PM Fiber Input Board and PM Fiber Receivers pair with PM Fiber Output Board See pg 35 for detail information e Use crossed RS 232 422 cable for serial control e Use crossed RJ 45 cable for LAN control Installation and Setup e Place the Matrix Router into a desired position and screw in the rack ear holes Recommended to screw all 8 holes for secure installation e Plug power cord into power supply unit on the Matrix Router For redundancy power use plug power cords into both power supply unit e Connect source devices to the Matrix Router s Input Board using appropriate cables e Connect display devices to the Matrix Router s Output Board using appropriate cables Connect control devices to the Matrix Router s communication ports Command
39. der Transmitter For example the command code 255IEIO01SP can be interpreted as follows Starting the command code 255 Router ID is 255 IE Input Extender source selection on 101 Input 01 Extender SP source to select VGA take the command For a complete list of command characters and their functions see examples below IE Input Extender Source Select SP VGA PC SH HDMI Example Command Codes Action 255IEIO1SP Set Input1 Extender source to VGA 255IEIO2SP I14SH Set Input2 Extender source to VGA Input14 to HDMI 255IEI01 O9SH Set Input1 9 Extender source to HDMI IP Input Extender Command Transmission Pass Through Mode 56 PureLink by Dtrovision The IP is an initiation command for sending command to the device that is connected to the Input Extender s rs 232 422 port The characters and numbers that follow the IP command tell the system send a command to the device through Input Extender The last character is found at the end of a command code which tells the system to execute the command In order to send control command to the AV devices that are connected to the PM Extender it needs to open the communication port and then send a command Port open command 255IP101 001 Command to the AV devices 101 21 89 01 50 57 30 OA OD 0D Port close command 255 PC 4 4 lt Carriage return in HEX format gt RS 232 Baud rate bps 001 4800 002 9600 003 144
40. dio out ports Audio Insertion Via 3 5mm stereo Audio in ports Maximum Data Rate 3 4 Gbps per color R G B Maximum Pixel Clock 165 MHz Standard DVI 1 0 HDMI 1 4 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Output Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible HDCP version 2 0 Support Hot Plug Detection Yes Single Board Weight 0 5 Ibs 0 23 kg 20 PureLink by Dtrovision HDMI Output Board with Scaling PM HOS4S a a gy Ez ao L HDMI Output Board with Scaling PM HOS4S Specifications Number of Port 4 HDMI ports Connector Type Female HDMI connector Signal Type RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Supported when HDMI signal source used Maximum Data Rate 3 4 Gbps per color R G B Maximum Pixel Clock 165 MHz Standard DVI 1 0 HDMI 1 3 Switching Speed Max 200ns Output DVI Re clocking Automatic Output Peripheral Device Power 600 mA per Output Output Equalization Automatic Max 30m 1920 x1200 50 60Hz or 1080p 8 bit color HDCP Compatible HDCP version 2 0 Support Hot Plug Detection Yes Single Board Weight 1 Ibs 0 45 kg 21 DVI Output Board PM DOS4 PureLink by Dtrovision
41. e Output Extender s rs 232 422 port The characters and numbers that follow the OP command tell the system send a command to the device through Output Extender The last character is found at the end of a command code which tells the system to execute the command In order to send control command to the AV devices that are connected to the PM Extender it needs to open the communication port and then send a command Port open command 2000PO001 001 Command to the AV devices 001 21 89 01 50 57 30 OA OD 0D Port close command 2550PC 44 lt Carriage return in HEX format gt RS 232 Baud rate bps 001 4800 002 9600 003 14400 004 19200 005 38400 006 57600 007 76800 008 115200 For example the command code 2550P101 001 type code 1 lt Please note that there should be two carriage return for this 2550PC specific command string the first one right after the and the last one should go after the closing quotation mark No space in between gt Above example can be interpreted as follows Starting the command code 255 Router ID is 255 OP Output Extender command transmission on 001 Output 01 Extender 001 at baud rate 4800 take the command Once communication port 62 PureLink by Dtrovision is open command 21 89 01 50 57 30 OA OD can be sent After receiving feedbacks from AV devices close the port 255O0PC For a complete list of command characters and their functions see exa
42. eate UP Preview Down Input and Output and Enter buttons for setting configuration Timing Input 1 1024 x 768 60Hz 2 1920 x 1200 60Hz 3 720 x 480P 60Hz 4 1280 x 720P 60Hz 5 1920 x 1080P 60Hz Test Pattern Input 1 Colorbars 2 Cross Hatch 3 16 Gray 4 256 Gray 5 4 Color Gray 8 Monitoring Out PM Matrix Router provides an HDMI preview monitoring port which further simplifies system testing by acting like an extra Video Output Select Input that needs to be checked and push enter button Selected Input will be Output to preview monitoring port 41 PureLink by Dtrovision 9 Firmware Version Matrix Router s firmware version can be checked using Up Down buttons 10 Factory Reset Factory reset will put the general setting back to the factory default mode Factory default setting value RS 232 Baud rate 19200 Bps IP Address 192 168 000 002 Gateway 192 168 000 001 Input Output Connection No Connection Product ID 255 e All Video Audio switching connection becomes clear e Serial communication setting will be restored back to the factory default Baud Rate 19200 Data Bits 8 Parity None Stop Bits 1 e LAN Communication setting will be restored back to the factory default IP Address 192 168 000 002 Gateway Address 192 168 000 001 Subnet Mask 255 255 255 000 42 PureLink by Dtrovision 4 2Command Line Operation Control Programmer s Guide Code Structure and Examples
43. eate a name ex PureLink e Bits per second 115200bps e Data bits 8 e Parity None e Stop bits 1 e Flow control None 69 PureLink by Dtrovision Disconnected Auto detect Auto detect SCROLL CAPS Num Capture Print echo 4 Hyper terminal setting Go to file gt Properties setting gt ASCII setup amp PureLink HyperTerminal oog A Connect To Settings Function arrow and ctrl keys act as Teminal keys Windows keys Backspace key sends Gate Del O Cast Space Cus Emulation Auto detect x Teminal Setup Telnet terminal ID ANSI Backscrollbufferlines 500 O Play sound when connecting or disconnecting Cx Cca Connected 0 01 19 Auto detect Auto detect SCROLL CAPS NUM Capture Printecho 70 PureLink by Dtrovision Check on Echo typed characters locally and then ok PureLink HyperTermina z mX PureLink Properties 7 x Connect To Setings i ASCII Sending Send line ends with line feeds X Echo typed characters locally mm q Line delay 0 milliseconds Emi Character delay 0 milliseconds ad ay Tel ASCII Receiving C Append line feeds to incoming line ends Force incoming data to 7 bit ASCII Wrap lines that exceed terminal width og Connected 0 03 22 A
44. ers and their functions see examples below Output CATx Fiber Ports Audio Select A Auto M Embedded Audio S 3 5mm Stereo Audio M Embedded Audio refers to embedded Audio from Input source side 59 PureLink by Dtrovision S 3 5mm stereo Audio refers to inserted Audio from Output Board s 3 5mm stereo jack Example Command Codes Action 255O0SALLM Set all CATx Fiber Output Audio selection to embedded 2550S001A 002M 003S Set CATx Fiber Output Audio on Output 1 Auto Output 2 embedded and Output 3 3 5mm stereo Audio 2550S001 09M Set CATx Fiber Output Audio on Output 1 9 embedded OT Output Test Pattern Select The OT is an initiation command for Output test pattern selection The characters and numbers that follow the OT command tell the system send test pattern to which Output The last character is found at the end of a command code which tells the system to execute the command y For test pattern command Output s resolution and pattern type selection are required For example the command code 2550TO01T02P04 can be interpreted as follows Starting the command code 255 Router ID is 255 OT Output test pattern on 001 Output 01 at T02 resolution 1920 x 1200 and P04 256 Gray pattern take the command For a complete list of command characters and their functions see examples below Resolution Table Pattern Type Table TOO Te
45. g Automatic Jitter lt 0 3 Ul Rise and Fall Times 20 80 135psecs Rise time fall time 2970Mbps Maximum Data Rate 2 97 Gbps Auto Data Rate Lock Yes Data Types Operation Standard 8 bits or 10 bits SMPTE 292M SMPTE 259M SMPTE 424M ITU RBT 601 ITU RBT 1120 Single Board Weight 1 5 Ibs 0 68 kg 18 PureLink by Dtrovision VGA Component Input Board PM AIS4 VGA Input Board PM AIS4 Specifications Number of Port 4 VGA ports 4 Stereo Input ports Connector Type Female 15 pin D Sub connector Female 3 5mm stereo jack Signal Type RGBHV or YPbPr component Video Bandwidth 170MHz 3dB Impedance 75 ohm Norminal level 0 7Vp p for RGB 1 0Vp p for YPbPr Maximum level 1 5Vp p Horizontal frequency 15KHz 100KHz Vertical frequency 30Hz 100Hz Sync Input level 3 5 5Vp p Audio Insertion Via 3 5mm stereo Audio in ports Single Board Weight 0 5 Ibs 0 23 kg 19 PureLink by Dtrovision 2 4QOutput Boards Specification HDMI Output Board PM HOS4 HDMI Output Board PM HOS4 Specifications Number of Port 4 HDMI ports 4 Stereo In out ports Connector Type Female HDMI connector Female 3 5mm stereo jack Signal Type RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Dolby Digital Plus Dolby TrueHD DTS HD Audio Extraction High Res DTS HD Master Audio up to 8ch PCM Via 3 5mm stereo Au
46. he command For a complete list of command characters and their functions see examples below Example Command Codes Action 255 IMI02 Set Input 2 to monitoring out 255 IMI00 No monitoring out Input Channel Information Request The IF is an initiation command for Input channel general information selection The characters and numbers that follow the IF command tell the system which Inputs channel information will be requested The last character is found at the end of a command code which tells the system to execute the command 55 PureLink by Dtrovision For example the command code 255IF 101 can be interpreted as follows Starting the command code 255 Router ID is 255 IF Input channel general information request on 101 Input 01 take the command For a complete list of command characters and their functions see examples below Example Command Codes Action 255IF 101 Check Input Channel 1 Information IE Input Extender Source Select The IE is an initiation command for Input Extender source selection The characters and numbers that follow the IE command tell the system which Inputs Extender source selection will be made The last character is found at the end of a command code which tells the system to execute the command v IE command only applies to the CATx Fiber Input Board with PM CT102 103 CATx and PM FT102 103 Fiber Exten
47. ink by Dtrovision 3G HD SDI CATx HDBaseT Fiber Optic Power External Power Supply DC12V 6 6A Power Consumption max 120W 120W Dual 240W Operational Temperature 32 117 F 0 to 47 C Storage Temperature Humidity 40 158 F 40 to 70 C 0 90 non condensing MTBF 50 000 hours Dimensions W x D x H 17 1 x 14 5 x 5 25 435 x 368 x 133mm Shipping Dimensions with cover box TBD Rack mounting Yes 19 standard rack 3RU Weight w o Boards installed TBD Weight with HDMI Boards fully installed TBD Shipping Weight TBD with Boards fully installed accessories hard metal case and cover box Shipping Weight of Individual Boards 2 Ibs 0 9 kg 13 2 3Input Boards Specification HDMI Input Board PM HIS4 PureLink by Dtrovision HDMI Input Board PM HIS4 Specifications Number of Port 4 HDMI ports 4 Stereo In out ports Audio Extraction Connector Type Female HDMI connector Female 3 5mm stereo jack Signal Type RGB digital Video DVI and HDMI standards or YCrCb digital component Video HDMI Digital Audio Dolby Digital Plus Dolby TrueHD DTS HD High Res DTS HD Master Audio up to 8ch PCM Via 3 5mm stereo Audio out ports Audio Insertion Via 3 5mm stereo Audio in ports Maximum Data Rate 3 4 Gbps per color R G B Maximum Pixel Clock 165 MHz Stan
48. ink by Dtrovision A Auto M Embedded Audio S 3 5mm Stereo Audio M Embedded Audio refers to embedded Audio from Input source side S 3 5mm stereo Audio refers to inserted Audio from Output Board s 3 5mm stereo jack Note For PM 128X and PM 256X input and output uses three digit format instead of two digits For example Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 Example Command Codes Action 2550MALLM Set all HDMI SDI Output Audio selection to embedded 2550MO01A 002M 003S Set HDMI SDI Output Audio on Output 1 Auto E Output 2 embedded and Output 3 3 5mm stereo Audio 2550MO01 09M Set HDMI SDI Output Audio on Output 1 9 to embedded OS Output Audio Select on CATx Fiber port The OS is an initiation command for Input Audio selection on CATx Fiber port The characters and numbers that follow the OS command tell the system which Output s CATx Fiber Audio will be set to which Audio source The last character is found at the end of a command code which tells the system to execute the command For example the command code 2550S001A 002M 003S can be interpreted as follows Starting the command code 255 Router ID is 255 OS Output Audio selection on CATx Fiber ports on 001 Output 01 to A Auto mode O02 Output 02 to M embedded Audio 003 Output 03 to S 3 5mm Audio take the command For a complete list of command charact
49. its For example Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 Examples Video status Command Codes Action 255 101 Check Video Output connection status on Input 1 250 007 4 Check Video Input connection status on Output 7 255 ALLIO 4 Check Video all Input and Output connection status Examples Audio status Command Codes Action 255A7101 Check Audio Output connection status on Audio Input 1 255A 007 4 Check Audio Input connection status on Audio Output 7 255A ALLIO 4 Check Audio all Input and Output connection status Input Board Function Configuration Input Board s Video and or Audio function can be configured via command control Configuration command can be sent to individual port or multiple ports at once Input Video source select command Input Audio source select command Input channel information request command Input Extender source select command Input Extender command transmission pass through command Input Video Source Select The IV is an initiation command for Input Video selection The characters and numbers that follow the IV command tell the system which Input will be set to which Video source The last character is found at the end of a command code which tells the system to execute the command Note For PM 128X and PM 256X input and output uses three digit format instead of two digits For example
50. l the system to request Audio volume information of selected Output The last character I is found at the end of a command code which tells the system to execute the command For example the command code 255AFO01 64 PureLink by Dtrovision can be interpreted as follows Starting the command code 255 Router ID is 255 AF request Audio volume information on 001 Output 01 take the command For a complete list of command characters and their functions see examples below Examples Command Codes Action 255AFO01 Check Audio Matrix Router Output 1 Audio volume information 255AFALLIO Check Audio Matrix Router s all Output volume information Router ID Check User can confirm the Router s Current ID setting v Universal Router ID is 999 Example Command Codes Action 9991000 Check Router s ID Firmware Version Check User can confirm Router s current firmware version Example Command Codes Action 999 version Check Router s Firmware version Baud Rate Setting User can set baud rate for RS 232 command control Enter the Baud rate setting command below Replace the s with the Input and Output number s 255 001 Baud rate at 19200 002 Baud rate at 38400 003 Baud rate at 57600 004 Baud rate at 115200 65 PureLink by Dtrovision Example Command Codes Action 255 001 Set
51. llable I O Input Output Boards The PM 8X Matrix Router can support up to 2 I O Boards of any of the above type The Matrix Router can switch any Input signal to any combination of Outputs For example HDMI Input signal can be Output to 3G HD SDI Output Fiber Optic Output and CATx Output The Matrix Router can route multiple Input Output configurations simultaneously Note 3G HD SDI is not a licensed HDCP interface and if the content received from HDMI is protected by HDCP there should be no Output from the 3G HD SDI Board PM series CATx I O Boards are used in conjunction with PM CATx Transmitter and Receiver and PM series Fiber Optic I O Boards are used in conjunction with PM Fiber Transmitter and Receiver Note For I O Boards and Extenders compatibility information see page 32 1 3 Front View The PM Matrix Router frame is mountable on a 19 standard rack Push button control panel and power switch are placed at the front panel as show in Figure 1 1 PureLink by Dtrovision HDMI 36 SDI HDBT aa OIC SEBO PM 8X 8x8 Cross Platform Modular Matrix Router Figure 1 2 Front view of PM 8X enclosure Push button control panel Power On Off switch Rack ears 1 4 Rear View Input Output Board section Audio Matrix Router communication ports and power supplies are placed on the rear panel as show in Figure 1 2 Actual rear view will vary depending on the configuration of Input Output Board type The rear
52. mmand for both 0x44 D Video and Audio this must Disconnect 1 0x64 d precede Input and Output specification Disconnect command for Video 0x56 0x44 VD Disconnect f only this must precede Input 2 0x76 0x64 vd Video only ane and Output specification Disconnect command for Audio 0x41 0x44 AD Disconnect i only this must precede Input 2 0x61 0x64 ad Audio only aie and Output specification Video connection status check 0x3F Connection status command this must precede 1 Input or Output specification Audio connection status check A Audio connection status command this must precede 2 Input or Output specification Separates the numbers within Space entries that contain multiple 1 numbers Specifies a range of numbers in Range 1 entries containing multiple 45 PureLink by Dtrovision numbers Input Video select M HDMI SDI Input Video select command IV this must ede Input and TOCATE pE ie a is s oa ideo selecti eci A Auto mode p a a eaua Input Audio select command IA a ee o must precede Input and A a aries Audio an S meee A Auto mode i Input Video preview monitoring IM Input monitoring select select command this must precede Input Input channel information IF Input channel information request command this must precede Input Input connected Extender s Input Extender Video select a ae CATx Fibe
53. mples below Example Command Codes Action 2550P001 001 Open communication port with a device that is connected to Output 2 Extender at 4800 bps baud rate O01 abcdefge Send command abcdefg to output 1 2550PC Close communication port 2550PO002 06 004 Open communication port with a device that are connected to Output 2 6 Extender at 19200 bps baud rate 2550P005 004 007 008 Open communication port with a device that is connected to Output 5 at 19200 bps baud rate and Output 7 at 115200 baud rate OALL pme 4 Send command pm to all open ports O02 purelink 4 Send command purelink to output 2 001 04 pm 256xe Send command pm 256x to output 1 4 OH 3G HD SDI Output Scaler timing select command The OH is an initiation command for 3G HD SDI Output Scaler timing selection The characters and numbers that follow the OH command tell the system set scaling timing on selected Output The last character is found at the end of a command code which tells the system to execute the command For a complete list of command characters and their functions see examples below OH command only applies 3G HD SDI Output boards T01 NTSC TO5 1920x1080i 50 TO9 1920x1080p 30 TO2 PAL TOG 1920x1080i 50 T10 1920x1080p 50 TO3 1280x720p 50 TO7 1920x1080p 24 T11 1920x1080p 60 T04 1280x720p 60 T08 1920x1080p 25
54. nal screen one at a time as noted below in the table The complete command has executed successfully when all of the entered characters including s which stands for status appear If a command character is not accepted a different character than the one entered appears and all or part of the command has not been executed Ack Acknowledge Value Response Table The following table shows ack value response characters along with their descriptions and meanings which may appear instead of the initially entered character or number If these characters appear all or part of the command has not been executed Table 5 2 Descriptions of Acknowledge ACK Signals Ack value Description Input 1 is not connected No information in channel 1 Command Code Error Indicates that system has rejected all or part of the command Router ID Error Indicates that the wrong ID number was entered Command Code Ack Value Examples 48 PureLink by Dtrovision Command Code Ack Value as appears in the Explanation of Result Entered control program The command was successfull 255C101001 255sC 101001 Was SUCCESSIUIY Executed The command was not executed 259CO001 Command Code Error because the Input number was not included The command was not executed 255C101001 Command Code Error oy because End was not included The command was not executed 300C101001 Router ID Erro
55. nected and operated in the same network either via serial or LAN communication Router ID can be set between 001 255 Factory default setting is 001 Note Router ID is associated with commend control Protocol therefore it is important to remember Matrix Router s current Router ID 3 RS232 There are four values those need to be set for serial communication baud rate data bits stop bits and parity Click and select each value using touch screen and push enter button to save Factory default recommended settings for serial communication are Baud rate 19200 Data bits 8 Parity none Stop bits 1 Flow control none and supported settings are Supported Baud Rate 4800 Bps 9600 Bps 14400 Bps 19200 Bps 38400 Bps 57600Bps 76800 Bps 115200 Bps Supported Data bit 5 bit 6 bit 7 bit 8 bit Supported Parity Non Even Odd Supported Stop bit 1 bit 2 bit 39 PureLink by Dtrovision 4 LAN PM series Matrix Router can be controlled through the 10 100 base Ethernet port using a command line interface There are four values that need to be set for LAN communication IP address Gateway address Subnet mast and Mac address Please use below button indication to configure LAN settings Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Output 1 9 Output 2 0 Output 3 COND OF WN Please use Output 3 button to mover cursor to
56. put 2 101 04 pm 256x Send command pm 256x to Input 1 4 Output Board Function Configuration Output Board s Video and or Audio function can be configured via command control Configuration command can be sent to individual port or multiple ports at once OM OS OT OF OE OP OH OM Output Audio select on HDMI SDI command Output Audio select on CATx Fiber port command Output Audio test pattern select command Output channel information request command Output Extender Scaler timing select command Output Extender command transmission pass through command 3G HD SDI Output Scaler timing select command Output Audio Select on HDMI SDI port The OM is an initiation command for Output Audio selection on HDMI SDI port The characters and numbers that follow the OM command tell the system which Output s HDMI SDI Audio will be set to which Audio source The last character is found at the end of a command code which tells the system to execute the command For example the command code 2550MO01A 002M 003S can be interpreted as follows Starting the command code 255 Router ID is 255 OM Output Audio selection on HDMI SDI ports on 001 Output 01 to A auto mode O02 Output 02 to M Embedded Audio 003 Output 03 to S 3 5mm Audio take the command For a complete list of command characters and their functions see examples below Output HDMI SDI Ports Audio Select 58 PureL
57. r Output Extender Scaler timing selection The characters and numbers that follow the OE command tell the system set scaling timing on selected Output The last character is found at the end of a command code which tells the system to execute the command For a complete list of command characters and their functions see examples below OE command only applies to the HDMI with scaling Board and CATx Fiber Output Board with PM CR102 CATx and PM FR102 Fiber Extender Receiver T00 Auto T09 1080p 50Hz T18 SXGA 1280x1024 75Hz T01 480p 60Hz 1T10 1080p 59Hz T19 SXGA 1280x1024 85Hz T02 576p 50Hz 711 1080p 60Hz T20 UXGA 1600x1200 60Hz T03 720p 50Hz T12 SVGA 800x600 60Hz T21 1360x768 60Hz T04 720p 59Hz T13 SVGA 800x600 75Hz T22 1366x768 6O0Hz T05 720p 60Hz 114 XGA 1024x768 60Hz T23 1440x900 60Hz T06 1080 50Hz 715 XGA 1024x768 75Hz T24 1920x1200 60Hz T07 1080 59Hz 716 XGA 1024x768 85Hz 61 PureLink by Dtrovision TO8 1080i 60Hz 117 SKGA 1280x1024 60Hz Example Command Codes Action 2550E001T00 Set Output 1 Extender Scaler timing to Auto 2550E002T 11 Set Output 2 Extender Scaler timing to 1080p OP Output Extender Command Transmission Pass Through Mode The OP is an initiation command for send command to the device that is connected to th
58. r because the actual Router ID and entered Router ID did not match Connecting Switches A switch is an active connection between an Input source signal and one or more Output display devices The signals connected in a switch command are either individual signals or groups of signals coming through the connectors on the rear of the unit Audio commands are for the independent green blocks Audio Matrix Router The C key initiates a Connect command for routing a switch The characters and numbers that follow the C command tell the system which Inputs and Outputs to connect The last character is found at the end of a command code which tells the system to execute the command For example the command code 255C101001 can be interpreted as follows Starting the command code 255 Router ID is 255 C Create connection on 101 Input 01 to 001 Output 01 take the command For a complete list of command characters and their functions see examples below To connect a switch Enter the Connect command below Replace the s with the Input and Output number s 255CI O Note For PM 128X and PM 256X input and output uses three digit format instead of two digits For example 49 PureLink by Dtrovision Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 Examples Connect Video and Audio Command Codes Action 255C101001 Connect
59. r only i e g OR command this must 2 SH HDMI pein p Input and Video selection Send command to the device that is connected to the Input Input Extender command l IP ee Extender CATx Fiber only this Transmission must precede Input baud rate timing Output HDMI SDI port is po Output HDMI SDI port s Audio Audio select OM M Embedded Audio select command this must edded Audio precede Output and Audio S 3 5mm Stereo l selection A Auto mode Output CATx Fiber port p 5 Output CATx Fiber port s Audio Audio select os M Embedded Audio select command this must i ed Audio l precede Output and Audio S 3 5mm Stereo selection A Auto mode Output Test Pattern Select Output test pattern select OT T01 1024 x 768 command this must precede T02 1920 x 1200 T03 720 x 480p Output resolution and pattern type 46 PureLink by Dtrovision T04 1280 x 720p T05 1920 x 1080p P01 Color bars P02 Cross Hatch PO3 16 Gray P04 256 Gray P0O5 4 Color Gray Output channel information OF Output channel information request command this must precede Output Output Extender CATx Fiber OE Output Extender Scaler only Scaler timing select timing select command this must precede Output and Video timing Send command to the device soure dee commana that is connected to the Output OP piae Extender CATx Fiber only transmission this must precede
60. r to the PM CATx Extenders Transmitter or Receiver at the remote location over the same CATx cable that transmits Audio Video and Control It eliminates the need of having a power on PM CATx Extenders Single CATx cable for Audio Video Control and Power makes installation simple Note Scaling Receiver PM CR102 does not support POE RS 232 An industry first the PM series RS 232 simplifies the control issues that have traditionally complicated system design RS 232 enables a single serial cable connecting the controller to a PM series Matrix Router to also control the system on three separate levels 1 PM series Matrix Router 2 PM series CATx and Fiber Extenders both Tx and Rx 3 Devices attached to PM series Extenders both Tx and Rx RS 232 simplifies control within most systems increasing reliability while also lowering costs by removing control design hardware and cabling Auto Scaling with Seamless Switching The PM series offers auto scaling on both the Router and Extender Receiver sides virtually eliminating latency while increasing system design flexibility The PM series HDMI Output Board PM HOS4S DVI Output Board PM DOS4S and 3G HD SDI 8 PureLink by Dtrovision Output Board PM SOS4 provides auto scaling for every PM series Matrix Router The CATx PM CR102 and Fiber PM FR102 Extender Receivers provide auto scaling directly driven by the PM series Matrix Router CATx and Fiber Output Boards
61. r warranty Customer Service Any customer service inquiries can be submitted electronically through the Q amp A form on our website at www purelinkav com For immediate assistance please contact us at 201 488 3232 to reach our customer care or tech support team 74
62. re Color End 2 Wire Color 1 Orange White Orange White 2 Orange Green 3 Green White Green White 4 Blue Blue 5 Blue White Blue White 6 Green Orange 7 Brown White Brown White LeSeeacyre 8 Brown Brown Straight through Cable Pin End 1 Wire Color End 2 Wire Color 1 Orange White Orange White 2 Green Green 35 PureLink by Dtrovision 3 Green White Green White 4 Blue Blue 5 Blue White Blue White 6 Orange Orange 7 Brown White Brown White 8 Brown Brown Audio Cable Termination for Audio Matrix Router 5 pin Phoenix connector is used for Audio Matrix Router s Input Output Please ensure to follow the picture below for Audio cable termination before connecting the cable L L RtR Pin Audio Phoenix Connector L Stereo Audio L Ground R Stereo Audio oO o n R Pinout from the left RS 232 422 Cable Termination for PM Extender Tx Rx 5 pin Phoenix connector is used for RS 232 422 communication between PM Extender Tx Rx to the devices that are attached Tx Tx Rx Rx Pin RS 232 RS 422 1 TX TX 2 Not used Tx 3 Ground Ground 4 Rx Rx 5 Not used Rx Pinout from the left 36 PureLink by Dtrovision Chapter 4 Operation PM series Matrix Router can be operated via three convenient methods 1 Front panel LCD touch s
63. smitter RF6 Rack mountable type DVI Loop Through single 3 5mm Audio in RS 232 6 600 ft PM series DVI over Fiber Optic Extender Transmitter RF6 Rack mountable type DVI and VGA selectable Input dual 3 5mm Audio in RS 232 6 600 ft PM series HDMI over CATx HDBaseT Extender Receiver Stand alone type Single 3 5mm Audio out POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Receiver Stand alone type Built in Scaler single 3 5mm Audio out POE RS 232 330ft Scaling Receiver PM CR102 does not support POE PM series HDMI over CATx HDBaseT Extender Receiver Wall Plate type Single 3 5mm Audio out POE RS 232 330 ft PM series DVI over CATx HDBaseT Extender Receiver Stand alone type Single 3 5mm Audio out POE RS 232 330 ft PM series DVI over CATx HDBaseT Extender Receiver Stand alone type Built in Scaler single 3 5mm Audio out POE RS 232 330ft Scaling Receiver PM CR102 D does not support POE PM series HDMI over CATx HDBaseT Extender Receiver RF6 Rack mountable type Single 3 5mm Audio out POE RS 232 330 ft PM series HDMI over CATx HDBaseT Extender Receiver RF6 Rack mountable type Built in Scaler single 3 5mm Audio out POE RS 232 330ft Scaling Receiver PM CR102 RF6 does not support POE PM series DVI over CATx HDBaseT Extender Receiver RF6 Rack mountable type Single 3 5mm Audio out POE RS 232 330 ft 29 PM CR102 RF6 D Note PM FR101 PM FR102 P
64. st pattern disable POO Test pattern disable T01 1024 x 768 P01 Color bars T02 1920 x 1200 P02 Cross Hatch T03 720 x 480P P03 16 Gray T04 1280 x 720P P04 256 Gray T05 1920 x 1080P P05 4Color Gray Example Command Codes Action 255OTALLT01P01 Set all Output to 1024x768 and color bars test pattern 2550TO01 002 003T02P04 Set Output 1 2 and 3 to 720x480p and 256 gray test Pattern 60 PureLink by Dtrovision 2550T001 09T05P05 Set Output1 9 to 1920x1080p and 4 color gray test Pattern 2Z55OTALLTOOPOO Disable test pattern to all outputs OF Output Channel Information Request The OF is an initiation command for Output channel general information request The characters and numbers that follow the OF command tell the system to request Output channel information of selected Output The last character is found at the end of a command code which tells the system to execute the command For example the command code 2550FO01 4 can be interpreted as follows Starting the command code 255 Router ID is 255 OF Output channel general information request on O01 Output 01 take the command For a complete list of command characters and their functions see examples below Example Action Request Output 2 information Command Codes 2550FO02 4 OE Output Extender Scaler Timing Select The OE is an initiation command fo
65. sting from the Matrix Router to the display Signal Analyzer Every PM series Matrix Router provides built in comprehensive signal analysis of both incoming and outgoing signals via the front panel LCD touch screen or control PureLink by Dtrovision command Signal information provided includes EDID HDCP transmission status and resolution Preview Monitoring Every PM series Matrix Router provides an HDMI preview monitoring port which further simplifies system testing by acting like an extra Video Output 12 5 Gbps Data Rate Frame Ensures lossless High Definition digital AV signal switching and distribution Input Boards directly compatible with PM Extender Transmitters PM CATx Fiber Input Boards can receive signal directly from PM CATx Fiber Extender Transmitter eliminating the need of matching Receiver Output Boards directly compatible with PM Extenders Receivers PM CATx Fiber Output Boards can send signal directly to PM CATx Fiber Extender Receiver eliminating the need of matching Transmitter HDMI v1 4 3D Support Adopting latest HDMI version 1 4 enables to support 3D 48 Bit Deep Color UHD 4K x 2K resolution optional and 7 1 Channel Dolby TruHD amp DTS MasterHD Standard Dual Redundant Power Every PM series Matrix Router is equipped dual redundant power supply as a standard Genlock for 3G HD SDI PM series Matrix Router s 3G HD SDI Board is equipped with Genlock feature to provide steady Video signals for optimum pi
66. t of command characters and their functions see page 67 Note For PM 128X and PM 256X input and output uses three digit format instead of two digits For example Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 Ack value Acknowledge value Response from Pure Link device will be echoed back to the terminal screen as the unit accepts them When a command is successfully executed all of the characters appear containing the character s which stands for status For example Ex 1 Command Connect Input 1 to Output 1 43 PureLink by Dtrovision 255C101001 Ack value 255sC 101001 Ex 2 Command Check Input connection status on Output 3 255 003 4 Ack Value 255s 103003 General Rules for Command Codes The commands are coded in ASCII and HEXA Please refer to Table 5 1 on pg 68 for detailed descriptions of keys and functions A basic command code setup is shown below Ex 255C101001 Start Router ID Command Input number Output number End Enter 255 C 101 001 GJ CE gt A command line allows execution of only one command Multiple commands require execution of multiple strings one command per string gt All commands begin with Start byte gt All commands end with End byte gt All commands will be executed when e Enter is entered gt The correct Router ID must be entered in a command code Systems will not react to the command if a
67. tput 2 and 030003 Input 3 to Output 3 255AC1I0010001 002 003 Connect Audio Input 1 to Output 1 2 and 3 250ACI0010001 007 Connect Audio Input 1 to Output 1 2 3 4 5 6 and 7 Disconnecting Switches The characters and numbers in a Disconnect command tell the system which Input or Output to disconnect The D key initiates a Disconnect command for routing a switch The characters and numbers that follow the D command tell the system that Inputs and Outputs to disconnect The last character is found at the end of the Command code which tells the system to execute the command For example the command code 255D101000 It can be interpreted as follows Starting the command code 255 Router ID is 255 D Disconnect on 101 Input 01 to O00 Output 00 take the command For a complete list of command characters and their functions see the command list below To disconnect a switch 51 PureLink by Dtrovision Enter the Disconnect command below Replace the s with the Input and Output number s 255DI O 4 Note For PM 128X and PM 256X input and output uses three digit format instead of two digits For example Input 01 1001 Input 05 1005 Output 01 0001 and Output 100 0100 Examples Disconnect Video and Audio Command Codes Action 255D101000 lt Disconnect both Video and Audio Input 1 to no Output 00 255D100003 04
68. ts The shipping group consists of the followings asssssassssss s SSS See Hom E 3688 Hoer nnananonn Eeee lelle sleli PMX 8x8 Cross Platform Modular Matrix Router 1 x PM series Matrix Router Main Frame Input Output Boards purchased separately AC Power Cords 1 x RS 232C Cable crossed type 1 x RJ 45 UTP Cable crossed type 1 x USB Cable for Firmware Update User s Manual vvvvvvey 3 2 Installation Environments For installation environments we recommend the following environments gt Below 30 C of ambient temperature gt Install and operate in the environment below 60 of ambient humidity Best condition gt Use it in the environment of free of vibrations and dusts and in good ventilation condition gt Avoid areas with direct sunlight heat sources or high levels of EMI EMI Electro Magnetic Interference gt Recommend stabilized AC Input power Recommend to use AVR AVR Automatic Voltage Regulator gt All physical connections to the product use industry standard connectors gt Be careful when you contact the product because some parts can be somewhat hot 31 PureLink by Dtrovision 3 3 Installation Note Before installing PM Matrix Router inspect the physical condition of the unit if there is any signs of damage If you find damage stop installing and contact your PureLink representative immediately When the unit has been inspected and found to be in good condition the installation
69. ucted at all times e Any external impact may cause damage to the operation of this unit e Be sure this product is properly grounded earthed in order to prevent the risk of electrical shock e Turn off and unplug power before adding or removing Input Output Boards e Input Output Boards may be damaged when they are replaced with power turned on e Use surge protectors and or AC line conditioners when powering this product e Only use a fuse s with the correct fuse rating in your enclosure e Make sure the product is on or attached to a stable surface If you experience any malfunctioning of product or have any question as to operation of the product please contact our customer service center Dtrovision LLC PureLink Tel 201 488 3232 Email support purelinkav com PureLink by Dtrovision 1 2 Product Introduction The PM series Matrix Router is a Cross Platform Matrix Router that supports multiple different digital interface types in a single unit PureLink s unique Cross Platform feature makes the Matrix Router most flexible and simple solution for today s sophisticated digital AV environment The PM series Matrix Router supports seven types of digital interface e HDMI v1 4 w optional scaling e DVI 1 0 w optional scaling e 3G HD SDI standard scaling e Analog VGA Component e CATx HDbaseT w optional scaling e Fiber Optic w optional scaling e Displayport Each Matrix Router is assembled from field insta
70. uto detect Auto detect CROI AP NUM 5 Type program and enter 23 a HyperTerminal BAX Fie Edit View Call Transfer Help De 58588 28 program DE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE EE MATRIX SOFTWARE PROGRAM MODE MATRIX MAIN 1 Enter key Push INPUT SLOT 2 Enter key Push OUTPUT SLOT 3 Enter key Push PROGRAM MODE EXIT E Enter key push x eK KK KK Connected 0 00 11 Auto detect 115200 8 N 1 ROL CAP NUM 6 Type 1 and enter 71 PureLink by Dtrovision a HyperTerminal Veg File Edit View Call Transfer Help De 8 al SendFie Receive File Capture Text Send Text File Capture to Printer PROGRAM MODE MATRIX MAIN 1 Enter key Push INPUT SLOT 2 Enter key Push OUTPUT SLOT 23 Enter key Push PROGRAM MODE EXIT E Enter key push xe KK System BootLoad Running 1 Application Program Download Wait ROM file a Abort ccceccc Sends a file to the remote system 7 Go to send T menu and then gt send file Select Ymodem Protocol De anr program ARAE O E E E E E E E E E E E E E E E E E EE E E E E E E HE E EEE EE EEE MATRIX SOFTWARE PROGRAM MODE MATRIX MAIN 1 Enter key Push INPUT SLOT OUTPUT SLOT csend rile nn Lig
71. view of PM 8X in Figure 1 2 is fully populated each of 3G HD SDI and CATx Input Board and Fiber and HDMI Output Board in PM 8X main frame errr see ee eee eens RRR SBH SST O MAT WR VSS PSSST Figure 1 2 Rear view of PM 8X Enclosure PureLink by Dtrovision Input Board Section 6 Board options are available Output Board Section 7 Board options are available Independent Audio Matrix Router Balanced or Unbalanced 5 pin Phoenix Connector Communication Board Audio Insertion Extraction on Input Board Audio Insertion Extraction on Output Board PureLink by Dtrovision Chapter 2 Features and Specifications 2 1 Features gt Cross Platform Switching Technology PureLink s advanced Cross Platform Switching Technology allows interchangeable switching between any Input signal formats to any Output signal formats PM Matrix Router supports HDMI v1 4 DVI 3G HD SDI VGA Component Fiber Optic amp CATx HDBaseT signal formats with various Input and Output selection Available in various I O sizes from 4x4 to 256x256 PM series Matrix Router offers a wide range of Input Output configuration to match various sized installations Total eight size of main frames are available PM 8X up to 8x8 PM 16X up to 16x16 PM 32X up to 32x32 PM 48X up to 48x48 PM 64X up to 64x64 PM 80X up to 80x80 PM 128X up to 128x128 and PM 256X up to 256x256 POE PM series Matrix Router provides powe
72. wrong Router ID is entered The factory default Router ID is set to 255 and the universal Router ID is 999 Systems will react to the command whenever universal Router ID is entered in command code gt Command codes typically are not case sensitive gt To specify multiple Inputs and Outputs enter a Comma between numbers Ex 255C101001 02 03 Connects Input 01 to Output 01 02 and 03 gt Use Hyphen for range connection EX 255C101001 04 Connects Input 01 to Output 01 02 03 and 04 Table 5 1 Command Codes Characters Table The table below shows command code characters keys which are used to generate control commands their functions and short function descriptions 44 PureLink by Dtrovision Ke 4 Function Description and Example Byte HEX ASCII 0x2A Start the command Header Code 1 0x21 End the command Tail Code 1 ODOA a Execute the command Execute the command 1 Initiates a Connect switch 0x43 C Connect command for both Video and 1 0x63 Cc Video and Audio Audio this must precede Input and Output specification Initiates a Connect Switch 0x56 0x43 VC Connect command for Video only this 2 0x76 0x63 vc Video only must precede Input and Output specification Initiates a Connect switch 0x41 0x43 AC Connect command for Audio only this 2 0x61 0x63 ac Audio only must precede Input or Output specification Disconnect co

PM Series Matrix Router Owner`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents