SPP-R300 - Barcodeyes
Contents
1. 1 Label Function Setting Label paper and black mark paper available at the label mode e Setting Operations 1 Turn on the printer power 2 Open the paper cover and press and hold down the paper feed button for longer than two seconds 3 After the buzzer tone is emitted insert paper and close the cover 4 Repeat the steps above to return to receipt mode e Setting Via Memory Switch Please refer to the memory switch changing section of the Commands Manual 5 2 Auto Calibration Function The label printing function requires the recognition of label paper gaps and black mark paper black bar in order to print If label paper gaps are not properly recognized use the auto calibration function e Auto Calibration Instructions 1 Turn the printer power off while in label print mode 2 Press and hold down the paper feed button and then press the power button 3 After the following printout is outputted press the power button to perform auto calibration Select the mode Auto Calibration Power Button Self Test Feed Button 4 Three pages of label paper are outputted when performing auto calibration Rev 1 00 24 6 Peripherals Connection SPP R300 This product can communicate with peripherals by using Bluetooth wireless LAN or external interface cable USB or serial cable 6 1 Bluetooth amp Wireless LAN Connection 6 2 Interface Cable Connection Rev 1 00 1 The printer can be connected t2. 5 Open the paper discharger when using the printer as shown in the figure e hr Rev 1 00 17 SPP R300 3 6 Shoulder Strap Usage 1 Connect the clips of the shoulder strap to the printer as shown in the figure on the left 2 Connect the clips of the leather case as shown in the figure on the left Rev 1 00 18 SPP R300 3 7 Car Cradle Optional Usage 1 Insert the printer as shown in the figure on the left and then press it in the direction of the arrows 2 To remove the printer pull the lever under the car cradle forward Rev 1 00 19 SPP R300 3 8 Control Panel Usage e Power Button This button is used to turn the printer on off 1 To turn the printer on press and hold the button for approximately two seconds when the printer is off 2 To turn the printer off press and hold the button for approximately two seconds when the printer is on e Paper Feed Button This button is used to feed paper manually take the self set and dump hexadecimals QQ 1 To feed paper manually press this button 2 For information on the self test refer to 4 Self Test 3 For information on the dump of hexadecimals refer to Service Manual e Battery Status Lamp Blue or Red BATT 1 If three blue lamps are lit the battery is fully charged 1 REY N 2 If two blue lamps are lit the battery is half charged E 7 lt N 3 If one blue lamp is lit t
3. _ 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ pacer ea Na 23456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W _ 3456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ B78 lt gt PQABCDEFBHI KL HNOPQRSTUVIXYZIW A a _ abcd abcde _ abcdef abcdefg abcdefgh abcdefgh 6789 lt gt 0ABCDEFGH I JKLMNOPQRSTUVWWXYZ W 789 lt gt QABCDEFGH I JKLMNOPQRSTUVWXYZ W 89 gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 9 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W _ l lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W PC437 LA on on Cu adaaac eitiAAEeAdsotuuyOU Ee Ptf U adaac eiTiAAEwA SoouuyOU E Pifa aaaac eitiAAEx A ooo0uyOU E Ptfaio aaac 6siiiAAESeHooo0uyOU E Ptfaidu aac eitiAAExA6ooduyOU E Ptfaioun ac eiiiAAExeA6o00uyOU EeE PtfaiouAN liiAA a E6660 0y g yxyPtfa R a TiiAA 2 F6660 y g gvyPtfa aso TiiAA 2 F66600y O g vxvpPtfa n ao ii S A oooduyOU GE PtfaiouAN g y iTAAE ce A O600UVOUGE PtFaloufiNeg r 1 iHA A 2F66600yO g vpPtf a Gu aos r 7 IAAF A O000UYOUGE PIfaioufiN r q AAE A6600uyOUGE PtfaiduAN s p qi AExA660uuyOU GE PtfaiduiN g p q i lt Ex A 6ooduyOU GE PtfaiduAiN s Pq Y2 Va j lt gt eEGO00UVO
4. are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user iS encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Rev 1 00 29
5. later Sensor Cutter Type Language User language supported Paper Type Thermal paper Width 79 5 0 5 mm 3 13 0 2 Paper Diameter Max 250 mm 1 97 Thickness 0 07 0 003 mm RENADIIY Batter Rechargeable up to 500 times Communication Serial USB Bluetooth Class2 V2 0 EDR Wireless LAN Interface 802 11 b g ipit Voltage 100 250 VAC P Current 0 5A Max at 110VA Voltage 8 4 VDC Current 0 8A The charging current and the charging time may vary Battery Charger Output Cell Voltage Battery r 2600mAh Charging Time Within four hours Usage Temperature 10 50 C 14 122 F Conditions Humidity 10 80 RH No condensation 110mm x 1627mm x 58 3mm Printer 4 33 x 6 38 x 2 30 Weigh am Printer 463g 1 02lbs Printer Battery 565g 1 25lbs Printer Battery Paper 698g 1 54lbs Shipping Package Approximately 13000 Basic Package Battery Battery charger Belt strap Battery protective case clean pen charger for vehicle Accessories Sold Separately shoulder strap cigarette lighter jack charger interface cable Quad charger 4 U Rev 1 00 27 SPP R300 8 2 Certification 1 WEEE Waste Electrical and Electric Equipment This mark shown on the product or its literature indicates that the x corresponding item should not be discarded at the end of its working life with asa other household waste To prevent possible harm to the environment or human health from uncontr
6. manual for instructions concerning insertion removal of batteries into from the product 2 As the battery is slightly charged upon factory shipment use it to confirm proper product operation upon purchase If product operation cannot be confirmed or longer use of the product is required use the exclusive charger to charge the battery 3 To avoid improper use of the battery review the product user manual carefully 4 Do not charge the battery for long times in excess of the normal charging time indicated in the user manual 5 If the battery is not to be used for a long period of time remove it from the product and store in a location with low humidity If the battery is stored while still inserted in the product in a highly humid location oxidization may occur along with a decline in battery performance 6 After product usage make sure to turn power off Neglecting to do so can cause a decline in battery performance 7 A battery that has not been used over a long period of time may not be sufficiently charged Even if the battery is not to be used charge the battery to the status recommended by the manufacturer once every six months Neglecting to do can cause a decline in battery performance and product life 8 If the battery terminal is dirty use a dry cloth to wipe clean prior to use Neglecting to do so can result in poor connection with the product causing power stoppages or failed charging 9 Each battery has a life c
7. strange smell and overheating on first use after purchasing the product contact your local dealer immediately If a child must use the battery the child s parent or legal guardian should clearly explain the instructions from the user manual prior to use In addition the parent or legal guardian should periodically confirm that usage is being conducted in accordance with user manual instruction during use Store the battery in a location that is out of the reach of small children During usage make sure to also place the charger and or product out of the reach of small children If the battery is leaking electrolytic solution and the solution comes in contact with the skin or clothing immediately wash thoroughly with clean water Contact with skin can result in skin disorders Make sure to review the user manual and precautions carefully prior to use In addition after carefully reviewing the user manual and precautions place them in a secure location for future reference when needed 10 There is a risk of explosion when replacing with an incorrect battery Only exchange it for another one of the same or equivalent model specified by BIXOLON Insulate the used battery by attaching insulation tape to its port and then dispose of the battery according to local regulations 11 If using the printed side of preprinted paper this may cause malfunction Rev 1 00 SPP R300 A Recommended 1 Review the user
8. 1 Do not place the battery within the reach of small children to prevent any swallowing accidents Ifa small child has swallowed the battery consult a physician immediately Do not place the battery in a microwave oven or a high pressure unit Doing so may cause sudden overheating of the battery and or the destruction of its seal resulting in battery overheating combustion and or explosion Do not use the battery with primary batteries like dry cells or other batteries of different capacity or type Doing so may cause excessive discharge in use or excessive charge when charging it resulting in an abnormal chemical reaction within the battery that can cause battery overheating combustion and or explosion There is a potential risk of overheating combustion and or explosion due to adverse chemical reaction in the battery If the battery starts to emit strange smells or if you find unusual symptoms such as overheating discoloration and deformation remove the battery from the product or the charger and discontinue use of the battery The use of the battery in abnormal status may result in battery overheating combustion and or explosion If the battery is not charged during a certain time when trying to recharge discontinue charging There is a potential risk of overheating combustion and or explosion If battery leaks its electrolyte or gives off a strange smell keep the battery away from open flames immediatel
9. 300 1 Content Confirmation The following items should all be contained in the printer package Contact the dealer from which the purchase was made if any item is damaged and or missing X Basic items X Optional items LA sy de Cigarette Lighter Interface Cable Protective Case Shoulder Strap Jack Charger Car Cradle Cleaning Pen Quad Charger Battery Rev 1 00 10 SPP R300 2 Product Part Names e Front Paper Cover Paper Feed Button MSR Cover e Rear Shoulder Strap Connection Holes Belt Strap Hole Power Connection Rev 1 00 11 3 Installation amp Usage 3 1 Battery Installation 3 2 Battery Charging 3 2 1 Battery Charging Usage Rev 1 00 SPP R300 1 Insert the battery on the rear side of the printer aligning the battery hook properly 2 Push the battery into the slot until a snapping sound is heard NOTE As the battery is not charged at the time of purchase charge the battery before use 1 Turn off the printer power 2 Connect the power cord 2 to the battery charger 1 and then connect AC power 3 Open the external interface cap in the direction of 4 Connect the battery charger to the power connector amp CAUTION The printer may be seriously damaged if a battery charger not provided by BIXOLON is used BIXOLON is not liable for such damage amp WARNING Turn off the power before charging the battery for the
10. BIXOLON User s Manual SPP R300 Mobile Printer Rev 1 00 http www bixolon com SPP R300 II Table of Contents X Manual Information amp Usage Precautions aaa a ura alas 3 1 Content Confirmation eeteetrnrnn enero 10 2 Product Part Names e a e um R a Ww w S wa a a Ww an RR a m S Wi a awia ma aaa 11 3 Installation amp Usage Sua gu pawa RET g s aa Was RS Bi Sa w ea S a gas aq EEC ee qe aS eC TE as a aku S a Ram Cer rere rr a S a Rw a W centric 12 3 1 Battery Installation laa aa ee ae ee ae ee ae ek aaa a i zs 12 3 2 Battery Charging selec cents abe inden ature oqka E nm fn atcha a rade aba A pad etapa pani pusaspa niwarqa 12 3 2 1 Battery Charging Usage SS 12 3 2 2 Cigarette Lighter Jack Charger Optional Usage a lle 13 3 2 3 Quad Charger Optional Usage A 13 3 3 Paper Installation A A Rp alc cael Rd lao ta Sha a Sica as 15 3 4 Belt Strap Usage O RO RE O 16 3 5 Protective Case Optional Usage mica 17 3 6 Shoulder Strap Usage See lc O O RR RR RR NANA RARA 18 3 Car Cradle Optional Usage e kata wa Pata Sala taa Oe awe DA eas Ota Tua saa Saa ata aa e Gae 19 3 8 Control Panel Usage ah hap at at ea en bateo rebase 20 3 9 MSR Usage A O aaa ysam imay RINA AA q a Wata qta Wa S A Qha acute 21 4 Self Test apa redada 21 5 Label Printing FUNCTION rre 24 5 1 Label Function Setting ts td ido aii cere ne Sec aaa aaa dave cere ee us eae ee ee 24 5 2 Auto Calibration Function m pz aun pz Sua s masma a a aha SS uY 24 6 Peripherals Co
11. RSTUVWXYZ W _ 56789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 6789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 789 lt POAC DEE OHI JK MNOPORSTUVWXYZIWIA s abcd abcde _ abcdef abcdefg abcdefgh abcdefgh 89 ae gt ABCDEFGH JKLMNOPQRSTUVWXYZ W 9 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W lt gt 20ABCDEFGH UJKLMNOPQRSTUVWXYZ W ie PC437 Cu adaac GitiAAEeAbo00uyOU E Ptf U aaaac eiTiAAEweA sooduyOU E Ptfa aaaac eitiAAEx HA oo00uyOU E Ptfaio aaac 6eiiiAAESHooonuuyOU E Ptfaidu aac eitiAAExAs6ooduyOU E Ptfaioun A TiiAA a E66060 y g vxvPtfa TiiAkA 2ae E666 00y g gvyPtfa R a TiiAKA 2 E6660 y g vyvPtfa nR ase ssimiAA z 00000 yOU CE YPIFA GUAN 4 O a iMAAE AddoduyOUGE PtfaloufNes J TIAAES A O600uUVYOUEGE PtfaiouAN 1 2 IAA 226F6660 0y g xvPtfA G as p 6 4 AA 2F66600y O g vPIf a as p qi AAy gEYPt f i b p q i lt Ex A 6ooduyOU GE PtfaiouAiN s Pq AR eEGO00UVOUGE PtFAIOUAN y 4 vic E AO600UVYOUGE PtfaidUAN p aA en 6660 yO g yptf a G a y 1 4 noe OOdUVOUGE PtfaiduAN s p q 1 4 ie 55 OQ y g vPtfAi G n as p q Wie xD GUYOUGE PtfaiouAN s p qo UyVOUGE PtfFaiouUAN e p 1 1 4 lt 50 9O vPtfa 6 ae r Y ne Completed SPP R300 9 Label Printing Function 5
12. UGE PtFAiOUAN y 4 YY ico PB E06600 yOUg vPtf ai F ee 6d00UVYOUGE PtfaioufiN g p 7 ie OOdUVOUGE PtfaiduAN s p q 1 4 lt 55 oduUyOUGEY PtfaiOuAN p q Wie xD GUVOUGENPtFaiOUAN g p q ie UyOUGEXPIFAT UAN 04 5 Vi re yOUGE PtfaiouAN py YY gt Completed e Self Test Sample For Wireless LAN Boot loader version VER v2 02 20100817 Firmware version V01 00 STOB 042211 Not available bluetooth WLAN firmware version Ver 0 1 wi cc7a00010877 System Name SPP R300 Network Mode Adhoc Encryption None ESSID BIXOLON_ adhoc DHCP Disabled IP 192 168 1 1 Netmask 255 255 255 0 Gateway 192 168 1 2 Port 9100 HTTPS Disabled Telnet Disabled FTP Disabled SNMP Disabled Butter Capacity 128K Bytes Print Density 100 Bluetooth Interface Baud rate 115200 bps Serial Interface Baud rate 115200 bps Data bits 8 bits Parity None Stop bit 1 bit or more Handshaking DTR DSR Default Codepage PC437 Print Speed 100mm s Double byte character mode Off Font 12 x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min Idle mode time 60 Sec MSR data including sentinel Character mode None MSR read mode Auto TRACK1 2 3 Memory switch setup status Memory S W1 12345678 ON A A OFF Hi HH HH Memory S W2 12345678 ON OFF MEA ENA Memory S W3 12345678 Memory S W5 Power off
13. d a fire e If the plug is wet or dirty dry or wipe it before usage e If the plug does not fit perfectly with the outlet do not plug in e Be sure to use only standardized multi outlets PROHIBIT gt 5 Do not pull the cable to unplug e This can damage the cable which is the origin of a fire or a breakdown of the printer PROHIBIT Do not plug in or unplug with your hands wet You can be electrocuted PROHIBIT Rev 1 00 You must use only the supplied adapter e It is dangerous to use other adapters ONLY SUPPLIED ADAPTER PROHIBIT Keep the plastic bag out of children s reach If not a child may put the bag on his head Do not bend the cable by force or leave it under any heavy object e A damaged cable can cause a fire PROHIBIT SPP R300 CAUTION Violating following instructions can cause slight wound or damage the appliance If you observe a strange smoke odor or noise from Keep the desiccant out of children s reach the printer unplug it before taking following measures If not they may eat it e Switch off the printer and unplug the set from the mains e After the disappearance of the smoke call your dealer to repair it a TO UNPLUG PROHIBIT Install the printer on the stable surface Use only approved accessories and do not try to disassemble repair or remodel it for yourself e If the printer falls down it can be broken and you can hurt p y yourself e Call
14. ff Font 12 x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min Idle mode time 60 Sec MSR data including sentinel Character mode None MSR read mode Auto TRACK1 2 3 Memory switch setup status Memory S W1 12345678 ON a a OFF EE OH UN Memory S W2 12345678 ON OFF BERHEEEE Memory S W3 12345678 Memory S W5 Power off time 12345678 Memory S W6 Idle time 12345678 ON EH OFF Ti Ea Memory S W7 Memory S W8 12345678 ON OFF BERHEEEE Memory S W Serial condition 12345678 ON OFF BERHEEEE Rev 1 00 29 gt SPP R300 SS S SS SS If ue want to continue LF TEST printing please press FEED button ASCII 1 8 0123456789 lt gt ABCDEFGH JKLMNOP 8 0123456789 lt gt ABCDEFGHI JKLMNOPQ 8 amp 0123456789 lt gt ABCDEFGH I JKLMNOPQR amp 0123456789 lt gt ABCDEFGH I JKLMNOPQRS amp 0123456789 lt gt ABCDEFGH JKLMNOPQRST amp 0123456789 lt gt 0ABCDEFGHI JKLMNOPQRSTU 0123456789 lt gt 0ABCDEFGH JKLMNOPQRSTUV 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVW 0123456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWX x 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXY 0123456789 lt gt 0ABCDEFGHI JKLMNOPQRSTUVWXYZ _ 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W
15. h ully Charged Within four hours Battery Defective or Poor Red Lamp Blinking nstalisti n amp CAUTION 1 If the red lamp of the charger blinks install the battery again 2 If the red lamp continues to blink despite several attempts 4 5 times to install the battery contact your local dealer 3 The charging time may vary depending on the type of the charger or ambient temperature Rev 1 00 14 SPP R300 3 3 Paper Installation 1 Press the Open button to open the paper cover 2 Insert the paper as shown in the image Remove any remaining core of a fully used paper roll 3 Take care to align the paper correctly 4 Pull the paper out as shown in the image and close the paper cover 5 Tear off any excess paper in the direction of the side of the printer Rev 1 00 15 SPP R300 3 4 Belt Strap Usage 1 Insert the belt strap screw into the belt strap hole 2 Use a coin to tighten the belt strap screw as shown in the image 3 Undo the belt strap Velcro 4 Fasten the belt strap to a belt D 5 Close the Velcro as shown in the image Z Belt Rev 1 00 16 SPP R300 3 5 Protective Case Optional Usage 1 Open its top cover 2 Insert your printer into the protective case as shown in the figure on the left 3 Close the Velcro 4 Using the clip in the rear of the leather case affix the case to a belt in the same way as using a belt strap
16. he card the recommended swiping speed is 100 1200 mm sec 4 Self Test Run the self test when first setting the printer or when encountering a problem and check the following Control Circuit Mechanisms Print Quality ROM Version and Memory Switch Settings If no issue is found with the printer after running the self test examine the other devices or peripherals and software This function is independent of such other devices and software e Self Test Instructions 1 Turn the printer power off and close the printer paper cover 2 Pressing the paper feed button and power button simultaneously turns the printer on 3 The printout is produced after releasing the two buttons 4 To add a printout of the ASCII pattern press the paper feed button once more 5 After the ASCII pattern is printed out the self test is automatically terminated Rev 1 00 21 e Self Test Sample For Bluetooth Boot loader version VER v2 02 20100817 Firmware version V01 00 STOB 042211 BT embedded Bluetooth firmware version 3 0 0 Bluetooth BD addre 001901223194 Auth amp Encry are enable Connection Mode 2 Not available WLAN Butter Capacity 128K Bytes Print Density 100 Bluetooth Interface Baud rate 115200 bps Serial Interface Baud rate 115200 bps Data bits 8 bits Parity None Stop bit 1 bit or more Handshaking DTR DSR Default Codepage PC437 Print Speed 100mm s Double byte character mode O
17. he battery is at the lowest charge level 4 If the red lamp is lit the battery must be charged or replaced e Error Lamp Left sided 1 If the red lamp is lit the paper cover is open 2 If the red lamp is blinking either the paper has been fully used or ERROR the print head is overheated Fill with paper or turn the printer off for at least 10 minutes 3 If the red lamp continues to blink it may indicate a more serious problem with the product and thus an authorized service dealer should be consulted e Bluetooth amp Wireless LAN Lamp Right sided 1 When using Bluetooth If the printer is ready for wireless communication with any Nari Bluetooth the green lamp as well as the battery status lamp is turned on 2 When using wireless LAN The right indicator shows the signal strength from wireless LAN The green lamp blinks for acceptable signal strength while the red lamp blinks for weak signal strength e In power save mode only the Status lamp is lit NOTE The power saving mode is activated after the first communication with the default time interval being 60 seconds Rev 1 00 20 SPP R300 3 9 MSR Usage 1 Press the MSR cover to open 2 Insert the card as shown in the image and swipe in the direction of the arrow can be done in both directions 3 When finished using press the MSR cover to close it NOTE If the card does not register first check to see if it is properly aligned When swiping t
18. nnection Tee a a w a aa m u a u w a aq w a a CE EEE a ua a aq a aS wa a awa aS wa aa EE ET ee s Swa S ee 25 6 1 Bluetooth amp Wireless LAN Connection Sei lath at lara E 25 6 2 Interface Cable Connection A din 25 7 Printer Cleaning Sci aa o E E Waq uu Gane cans dacs cues aa q aa sS um S um aus a u asta sura wS sta a wt S ata ara a aaa 26 8 Appendix E aa a paq awak de a aa 27 8 1 Specifications DRAE hE wanu RA Aaa A SN A A E ha cit Pana e am oe inne uama atan U 27 8 2 Certification Samana imapas smua E upam a apa Ya RA ad sd E BRASS eR Sa eae 28 8 3 Label Types uama kukaa y Nesconset ph qt nat cl aha ru fg ole gt hs nal teat apuka as gh tat 28 Rev 1 00 2 SPP R300 E Manual Information This user s manual contains basic information for product usage as well as for emergency measures that may be required Xx The following separate manuals provide more detailed content on various technological issues and areas 1 Windows CE Module Program Manual This manual provides information on the dll files required for Windows CE application program development 2 Windows Driver Manual This manual provides information on installation and main functions of the Windows Driver for this product 3 Unified Utility Manual This manual provides information on the software used to select functions of this product modify operation conditions etc e VMSM Virtual Memory Switch Manager As a function that sets the basic operation conditions of the pr
19. o devices equipped with Bluetooth communication capacity PDAs PCs etc 2 Use the Bluetooth connection function supported by the device to connect to the printer 3 The printer can be connected to other stations such as PDAs and PCs supporting wireless LAN communication in Ad hoc mode and AP in Infrastructure mode NOTE Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection You can check the bluetooth environment authentication encryption connection mode and the wireless LAN environment IP SSID authentication encryption via the self test page 1 Open the external interface connector protection cap in the direction of the arrow 2 Connect the external communication cable option to the connector NOTE Only use USB or serial cable option provided by BIXOLON 3 Connect the interface cable to the USB port of the device PDAs PCs etc NOTE The interface cable that can be connected with the printer is available in both USB and Serial type Refer to the service manual for detailed interface cable specifications 25 SPP R300 7 Printer Cleaning If the interior of the printer is dusty print quality can decline In such a case follow the instructions below to clean the printer Ah CAUTION e Make sure to turn the printer power off prior to cleaning e As the print head gets very hot during printing if intending to clean the print head turn the
20. oduct the use of non hardware control software based virtual switches is explained e NV Image Download Manager The downloading of image files such as logos intended for repetitive printing is explained e Firmware Download Manager The downloading and installation of the latest Firmware which is subject to ongoing modification for the enhancement of product performance are explained 4 Bluetooth amp Wireless Manual e Bluetooth This manual describes how to connect terminals PDAs PCs etc with Bluetooth functionality e Wireless LAN This manual describes how to connect wireless LAN in infrastructure or ad hoc mode 5 Commands Manual This manual provides information on the protocol and functions of the control commands that can be used with this product 6 Code Pages Manual This manual provides information on each character code page that can be used with this product We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products In following product specifications and or user manual content may be changed without prior notice Rev 1 00 3 W Safety Precautions SPP R300 In using the present appliance please keep the following safety regulations in order to prevent any hazard or material damage WARNING Violating following instructions can cause serious injury or death Do not plug several products in one multi outlet e This can provoke over heating an
21. olled waste disposal please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can conduct environmentally safe recycling of such items Commercial users should contact their suppliers and check the terms and conditions of purchase contracts This product should not be combined with other commercial waste for disposal 2 This equipment is indooruse and all the communication hiring are limited to inside of the building 3 The switch is the disconnecting device Turn off switch from any hazard A Warning Lithium lon Battery pack lt Warning gt The battery has the potential risk of overheating fire and or explosion To avoid such risks observe the following instructions e A visibly swollen battery may be dangerous Contact BIXOLON or your local dealer Only use an eligible charger e Keep away from open flames Do not place in a microwave e Do not leave the battery pack inside a vehicle in summertime e Do not store or use in a hot and humid place like a sauna with sleeping rooms e Do not place the battery pack on a quilt an electric blanket or a carpet for a long time e Do not store the battery pack switched on in an enclosed place for a long time e Do not allow the battery port to touch metal items s
22. printer 12 SPP R300 3 2 2 Cigarette Lighter Jack Charger Optional Usage 1 Turn off the power to the printer 2 Connect the cigarette lighter jack charger 1 to your car s cigarette lighter jack 3 Open the external interface protection cap in the direction of 4 Connect the battery charger to the power connector amp CAUTION The printer may be seriously damaged if a battery charger not provided by BIXOLON is used BIXOLON is not liable for such damage amp WARNING Turn off the power before charging the battery for the printer 3 2 3 Quad Charger Optional Usage 3 2 3 1 Connecting the cables 1 Connect the power cord to the adaptor and Connect the adaptor to the power connector of the Quad Charger 2 Plug the power cord into a power Outlet Input power is 100 240VAC 50 60Hz 1 4A 3 When power is supplied the amber and green Lamp turn on for two seconds amp WARNING Use only designated AC DC adaptor 12VDC 5A Rev 1 00 13 SPP R300 3 2 3 2 Battery Charging 1 Insert the battery into the Quad charger as shown in the figure on the left 2 Gently slide the battery until it reaches the bottom of the charger 3 Charging starts as soon as the battery is completely inserted 4 After charging remove the battery from the Quad charger NOTE Battery charging status descriptions are as follows Charge Status Charge Time Red Lamp On Charging L Fully C
23. printer power off and wait approximately 10 minute before commencement e When cleaning the print head take care not to touch the heated portion of the print head The print head is susceptible to damage from static electricity etc e Take care not to allow the print head to become scratched and or damaged in any way n S 1 Open the paper cover and remove any paper that may be present 2 Wipe the print head with a cleaning pen 3 Use a cloth moistened with an alcohol solution to clean the paper sensor are and remove any paper remnants and or dust 4 Insert paper into the printer 1 2 minutes after completing the cleaning process and close the printer cover Rev 1 00 26 SPP R300 8 Appendix 8 1 Specifications tem Description Printing Method Thermal printing Printing Speed 100 mm sec Resolution 203 DPI ones Easy paper loading Font A 12 x 24 Character Size Font B 9 x 17 Font C 9 x 24 Characters Font A 48 Per Line Font B C 64 English 95 Expanded Graphics Standard ENG 128 x 30 pages Character Set Others KOR CHN JPN 128 x 20 pages International 32 1 Dimension UPC A UPC E CODE 39 CODE 93 Barcode Code 128 EAN 8 EAN 13 ITF Codabar 2 Dimension PDF417 DATAMATRIX MAXI QR Emulation BXL POS Bauer Windows 98 ME 2000 NT4 0 XP WEPOS 2003Server VISTA 2008Server 7 Windows 98 ME 2000 NT4 0 XP WEPOS SDK 2003 Server VISTA 2008Server 7 Windows CE 3 0 and
24. r subject it to strong shock If the safety mechanism in the battery is damaged the battery may be overcharged and consequently an adverse chemical reaction may be generated in the battery There is a potential risk of battery overheating combustion and or explosion Rev 1 00 6 10 SPP R300 Do not pierce the battery with a pointed object such as nail or awl or strike with a heavy object such as a hammer and take care not to step on the battery There is a potential risk of battery overheating combustion and or explosion caused by an internal short circuit 11 Do not solder the battery directly Doing so may melt the insulating materials and or damage the safety mechanism or safety equipment resulting in battery overheating combustion and or explosion 12 Do not disassemble and or modify the battery The battery contains safety equipment and a safety mechanism to prevent danger There is a potential risk of overheating combustion and or explosion caused by disassembly 13 Do not charge the battery near open flames and or under direct sunlight Because exposure to high temperatures triggers the operation of the safety mechanism the battery may not charge or may overcharge due to destruction of the safety mechanism There is a potential risk of overheating combustion and or explosion 14 Do not expose the battery to high temperatures over 60 C and do not use or store it in a hot or humid place amp Warning
25. rheating combustion and or explosion of the battery Charging the battery with a modified charger may result in overheating combustion and or explosion of the battery by abnormal chemical reaction caused by incorrect polarity Do not directly connect the battery to an electrical power outlet not specified by BIXOLON or an automobile s cigarette lighter jack Doing so may result in overheating combustion and or explosion of the battery by over current and or over voltage Do not heat the battery or place it near a fire Doing so may melt insulation materials damage the safety mechanism equipment and or ignite the electrolytic solution There is a potential risk of battery overheating combustion and or explosion Always observe correct polarity when using the battery Charging the battery with incorrect polarity may cause an abnormal chemical reaction and discharging the battery may generate an unexpected over current There is a potential risk of battery overheating combustion and or explosion Do not allow the battery s or pole to come into contact with any metal In addition do not carry or store the battery with metallic items such as necklaces and hairpins Doing so may cause a short circuit of the battery generating an over current There is the potential risk to overheat ignite and or explode the battery or overheat the metallic items such as necklaces hair pins etc Do not throw the battery o
26. time 12345678 Memory S W6 Idle time 12345678 EH OFF Ti AR Memory S W7 12345678 ON EH OFF MENA E Memory S W8 12345678 ON OFF MERES EEE Memory S W Serial condition 12345678 ON OFF MEREEN EE Rev 1 00 93 SPP R300 S SS If de want to continue LF TEST printing please press FEED button ASCII 1 8 0123456789 lt gt ABCDEFGH JKLMNOP 4 8 0123456789 lt gt ABCDEFGHI JKLMNOPQ 8 amp 0123456789 lt gt ABCDEFGH I JKLMNOPQR amp 0123456789 lt gt ABCDEFGH JKLMNOPQRS amp 0123456789 lt gt ABCDEFGH JKLMNOPQRST amp 0123456789 lt gt 0ABCDEFGHI JKLMNOPQRSTU 0123456789 lt gt 0ABCDEFGH JKLMNOPQRSTUV 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVW x 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWX x 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXY 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ _ 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W _ 0123456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W 0123456789 lt gt 0ABCDEFGH I JKLMNOPQRSTUVWXYZ W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ psc maa Ge eC ea 23456789 lt gt ABCDEFGH I JKLMNOPQRSTUVWXYZ W _ 3456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 456789 lt gt ABCDEFGH JKLMNOPQ
27. uch as necklace coin key or clock etc e Use the lithium secondary cell guaranteed by mobile phone manufacturer or BIXOLON e Do not disassemble compress or pierce the battery pack e Do not drop the battery pack from a high place or subject it to strong shock e Do not expose the battery to high temperatures over 60 C e Do not expose to humidity Disposal Directions e Do not dispose of waste battery packs recklessly e Do not burn or throw in fire to dispose of the battery pack There is a risk of fire and or explosion e How to dispose of battery packs may vary depending on countries or regions Dispose of it in the correct method Recommendation for Charging e Do not charge your battery pack in a way not mentioned in the instruction manual Doing so may result in fire or explosion 8 3 Label Types The labels used on this product are composed of the following materials e BIXOLON logo label PC e Rating Label PP e Other labels PET Rev 1 00 28 SPP R300 FCC compliance Information This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Information to the user NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits
28. y The leaked electrolyte may catch fire There is a potential risk of overheating combustion and or explosion If the battery is leaking electrolytic solution and any of the solution enters the eyes immediately wash out with clean water and then consult a physician to receive treatment Neglecting to do so can cause permanent eye injuries Rev 1 00 SPP R300 A Caution 1 Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight such as within an automobile Doing so can cause battery overheating and or combustion In addition battery performance and product life may be reduced The battery contains a safety mechanism to prevent danger Do not use the battery in a location that is prone to static electricity above the amount covered by the manufacturer s product warranty that can cause damage to this safety mechanism Damage to the safety mechanism can result in battery overheating combustion and or explosion The temperature ranges for battery usage are as follows Any usage outside of these ranges can result in battery overheating and or damage In addition battery performance and product life may be reduced Charging 0 40 C Product Usage 20 60 C Storage 20 60 C 30 days Long Term Storage 20 40 C 90 days Please review the exclusive charger manual carefully for charging instructions If you observe any abnormal symptom such as
29. ycle If the usage time of the produce is shortened replace with a new battery Insulate the used battery by attaching insulation tape to its port and then dispose of the battery according to local regulations E Other Precautions The copyright for this user manual and various other manuals is property of the BIXOLON Co Ltd Any copying or conversion into electronic firm and saving of this material without the express written permission of BIXOLON Co Ltd is strictly prohibited Use of the information contained in this manual is not subject to any patent liability This manual has been prepared with utmost care and attention to detail but may contain certain errors and or omissions BIXOLON Co Ltd is not legally liable for any damages resulting from the use of the information in this manual BIXOLON Co Ltd and its affiliates are not legally liable United States excluded for any damages loss costs and or expenses that result from the breakdown malfunction and or misuse of the product due to violation or neglect of the operation and maintenance information and instructions provided by the BIXOLON Co Ltd as well as from the unauthorized alteration repair and or modification of the product by the user and or third party BIXOLON Co Ltd is not legally liable for any damages and or issues resulting from the use of options and or parts that are not authentic BIXOLON products or authorized products Rev 1 00 9 SPP R
30. your dealer when you need these services Do not touch the blade of auto cutter DISASSEMBLING PROHIBIT PROHIBITED Do not let water or other foreign objects in the Do not use the printer when it is out of order This printer can cause a fire or an electrocution e If this happened switch off and unplug the printer before e Switch off and unplug the printer before calling your dealer calling your dealer PROHIBIT W TO UNPLUG Rev 1 00 5 SPP R300 W Battery Safety Precautions Make sure to review the user manual carefully prior to product use Neglecting to heed the following instructions can result in battery overheating combustion explosion damage and or decline in performance and product life amp Danger 1 Do not allow water seawater or moisture to enter or leak into the battery If the safety mechanism within the battery becomes oxidized the battery may overcharge with abnormal electrical current and or voltage so that it may overheat ignite and or explode Do not place the battery near open flames or heating devices such as stoves Exposure to excessive heat may cause damage to the resin case and or insulating materials thus causing a short circuit within the battery that may result in battery overheating combustion and or explosion Charge the battery only with the exclusive charger specified optionally provided by BIXOLON The use of an incorrect charger may result in ove
Download Pdf Manuals
Related Search