User`s Manual Important Information, Please Read - AV
Contents
1. One Line 212 System can be quickly and safely posi tioned on top of a vertically placed SW 215E Two Line 212 systems can be precisely arrayed on top of a horizontally placed SW 215E Horn not rotated on Horn rotated on standing Line 212 system standing Line 212 system Line 212 6 SP with Line 212 6 SP Line 212 6 SP with Line 212 9 SP Other combinations of Line 212 Systems are not recommended as they can cause unwanted interferences KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 18 of 47 User s Manual K amp F SW Series Subwoofer Systems 7 Short Circuit Fuses in the K amp F Subwoofer Systems 7 1 Risks of using High Performance Power Amplifiers In recent years power amplifiers have achieved increasingly higher levels of perform ance Some of them can be operated with low impedance loads There are therefore strong power amplifiers that can reliably work with impedances below 1 Q This devel opment has led to an increased safety risk during defective operations When there is a defect such as a short circuit in the speaker chassis or on the crossover it is possible that the power amplifier despite existing protective switches will not shut off Long cable lengths and contact resistance on the2. For using Subwoofers wi n XO set switch on ALL SPEAKONS 1 1 gt OPTIONAL REMOTE UNIT oj l1 cuz INPUT AMP MID HIGH A Do e Mm pu AMP BASS ELT ABI C O The switch XO on the connecting terminal of the subwoofer must be at XO OFF for this mode of operation or XO on e Switch on the subwoofers connecting terminal The countersunk switch Full Range Mode on the C2 Controller should not be pressed and the LED assigned to it should not light up If you are using the mid high systems in a cluster speakers in close proximity press the Top Low Cut switch on the C2 Controller Advantages of the active mod Possibility to separately adjust the level of the subwoofer The mid high systems do not receive any low frequency signals and are not as strained Higher achievable total sound power level While taking the various mid high systems the frequency response of the system can be optimised application specifically The C2 Controller optimises the operating safety through special limiters KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 25 of 47 User s Manual K amp F SW Series Subwoofer Systems 10 Operating the Speakers Switch off all equipment and turn down all level controls Connect your subwoofers in accordance with prece
3. 7 4 2 Subwoofers with Crossover XO The fuses of the subwoofers with a crossover are serially mounted on the crossover The exact position is described in the chapter Internal Wiring of Subwoofers with Low Pass Filter XO beginning on page 27 for the particular models If it happens to be a model which has already been upgraded then the fuse holder is mounted on the signal wiring behind the input connector When replacing the fuse in both cases the chassis must be removed in order to reach the fuse holder Unscrewing the connecting terminal does not enable you to reach the fuse holder When the chassis is re assembled first loosely fasten the screws diagonal from one another then tighten them By tightening the screws diagonally in two steps a defor mation of the chassis and thus a possible de centring of the voice coil can be avoided 7 5 Add On Kits for Subwoofers without Short Circuit Fuses All subwoofer systems which are not serially equipped with short circuit fuses can be if required easily and inexpensively upgraded even by yourself An instruction manual for this upgrade is delivered with the add on kit Subwoofers with a crossover that are not serially equipped with short circuit fuses can also be if necessary upgraded with fire safety fuses The crossover does not need to be replaced For this we offer an add on kit that is mounted between the crossover input and the input connector KLING amp FREITAG GM
4. plastic sliders in ST CN o D O Q D U Cc 4 Es O K amp M fixing plate M20 for stacking cavities stacking cavities KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 42 of 47 User s Manual K amp F SW Series Subwoofer Systems 15 4 SWi 115E a mou DIMENSIONS 696 1 WW OG LYS Z1 WW PSY 696 1 ww OS LV m V c o U S o D N ge D iS r N 98 v8 61 98 ww OPE WW OS c WW OVE KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 43 of 47 User s Manual 15 5 SW 118E Plastic Sliders a SES 7C WW v c S a 196 1 WW 8 67 Rigging Points allsafe Jungfalk 120030 31 Fixing Plate for a LSY 97 l WW c 9 Distance Rod M20 K amp M 24115 K amp F SW Series Subwoofer Systems DIMENSIONS RE SOC CL UJUJ OLE Z6L GC WW Qv9 KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 44 of 47 User s Manual 15 6 SWi118E 96L SZ WW O79 KLING amp FREITAG GMBH 1998 2006 K amp F SW Series Subwoofer Systems DIMENSIONS VES CC pu WW p ZAS 196 I Rigging Points WW ger Th
5. User s Manual 13 Technical Specifications 13 1 SW 112 Speaker Design Frequency range 10 dB Frequency range 3 dB Crossover frequencies Power handling Sensitivity 1 W 1m Max SPL Components Impedance nom XO ON Without crossover XO OFF Connectors Enclosure Dimensions W x H x T Weight Options Accessories K amp F SW Series Subwoofer Systems Bass reflex system with exponential tunnel geometry 35 Hz 2 5 KHZ 41 Hz 350 Hz max 110 Hz with optional low pass filter XO ON 500 W nominal 1000 W programme 92 dB 45 Hz 350 Hz 93 dB 40 Hz 110 Hz with optional low pass filter XO ON 124 dB peak 1 m free field equivalent 130 dB half room 1 x 12 long excursion chassis 100 mm voice coil internal and external ventilation 6 Q Zmin 4 Q 8 O Zmin 6 Q 2 x Speakon NLAMP 1 4 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU 1 ergonomic handle K amp M mounting plate M20 for distance rod 4 non abrasive plastic feet stacking foot grooves for stacks of identical enclosures ball proof steel grille with exchangeable black acoustic foam 470 x 370 x 520 mm 27 kg 28 7 kg with low pass filter XO switchable low pass filter terminal clamp instead of Speakon connector 100 Volt with 300 VA toroidal transformer 29 5 kg not in combination with option XO Suspension with 6 flying poin
6. 4 integrated handles K amp M mounting plate M20 for distance rod 8 non abrasive plastic feet stacking foot grooves for stacks of identical enclosures as well as for single or clustered Line 212 enclosures 4 x 100 mm rear mounted castors 2 locking profiles for optional transport cover ball proof steel grille with exchangeable black acoustic foam 480 x 1015 x 765 mm incl castors 68 5 kg terminal clamp instead of Speakon connector without 100 mm transport castors Suspension with 6 flying tracks allsafe JUNGFALK Outdoor Mobile Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 5096 duty cycle 3 2 83 Vrms free field KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 35 of 47 User s Manual K amp F SW Series Subwoofer Systems 14 Frequency Diagrams 14 1 SW 112 SWi 112 14 1 1 Without optional Low Pass Filter or XO OFF SPL dB Impedance Ohm 100 316 90 100 E 9 qp uc U ea c S go 316 E 2 E 70 10 60 3 16 20 100 1000 Frequency Hz 14 1 2 With optional Low Pass Filter XO ON SPL dB Impedance Ohm 100 316 90 100 E Q qp em U ea c SD geo 31 6 5 2 E 70 10 60
7. K amp F SW Series Subwoofer Systems Version 4 0 User s Manual Released 23 03 2006 Important Information Please Read Before Use KLING amp FREITAG GmbH E Junkersstrasse 14 MENG D 30179 Hannover FREITAG PHONE 0 049 511 969 97 0 FAX 0 049 511 67 37 94 www kling freitag de SOUND SYSTEMS User s Manual K amp F SW Series Subwoofer Systems KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 2 of 47 User s Manual K amp F SW Series Subwoofer Systems Thank you for your decision to buy a Kling amp Freitag sound system To guarantee a trouble free operating of the equipment and to allow the KLING amp FREITAG sub woofer system to achieve its full potential please read the operating instructions care fully before use With the purchase of a K amp F subwoofer system with integrated power amplifier tech nology you have acquired a speaker system with the highest possible quality and performance capabilities As the owner of this system you now have a versatile and highly professional tool which when operated properly is a true pleasure to use Symbols in User s Manual This symbol indicates the possibility of life threatening danger and a health risk for persons Not following these instructions may result in serious health problems including potentially fatal injuries Warning This symbol indicates a possibly dangerous situation Not following these instructio
8. 17 Supplied Safety and Mounting Instructions for Speakers and Accessories KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 5 of 47 User s Manual K amp F SW Series Subwoofer Systems 1 General Safety Instructions for Using Speakers Mounting the speakers To prevent injury the speakers must be securely placed on the floor or secured to the wall according to the instructions on page Fehler Textmarke nicht definiert Mounting Instructions for Speakers Please note that speakers can move as a result of vibrations To prevent them from falling from their mounted position they must be secured properly If the weight of the speaker exceeds 20 kg then it is necessary for two people to carry it Speakers may only be suspended or mounted to walls or ceilings by qualified personnel The speakers must be hung by using at least two of the designated flying points The same applies when lifting and aligning the speakers Never use signal cables or power cords for suspending aligning or securing the systems When laying the connecting cables make sure that nobody can trip Never hang more than two speakers under one another without using the designated Kling amp Freitag rigging equipment Ensure that all installation connections comply with the applicable safety guidelines and that the size and strength are sufficient Further instructions are in our user s manual for assembly equipment and in the general safety instructions
9. 80 10 70 3 16 20 100 1000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 38 of 47 User s Manual K amp F SW Series Subwoofer Systems 14 4 SW 215E SPL dB Impedance Ohm 110 316 100 100 E 9 Ww p U E E e E 80 10 70 3 15 20 100 1000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 39 of 47 User s Manual K amp F SW Series Subwoofer Systems 15 1 SW 112 allsafe Jungfalk only with option Suspension Rigging Points 120030 31 DIMENSIONS 86S C1 ww OZE E 896 1 ww OS Fixing Plate for Distance Rod M20 v 9 4 ww QOZ latr Oc ww OZS 9 TZ OL UU Q9Z KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 40 of 47 User s Manual K amp F SW Series Subwoofer Systems 15 2 SWi 112 DIMENSIONS 86S Z1 WW OZ 896 1 WW OG Rigging Points Thread Inserts M12 rm 896 1 ww OS je 896 1 999 PL ww OG WW O a ZLY OZ 629 OI WWW OZZ KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 41 of 47 User s Manual K amp F SW Series Subwoofer Systems 15 3 SW 115E DIMENSIONS
10. K amp F SW Series Subwoofer Systems 2 2 SWi 112 Short description Ultra compact high performance subwoofer for fixed installations with exponential tunnel geometry controllable with system controller direct emitting 12 long excursion chassis bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint highly permeable ball proof steel grille with exchangeable black acoustic foam The subwoofer is equipped with twelve M12 threads for flown applica tions or mounting devices Optional versions Option XO Version with integrated low pass filter 110 Hz for operations without system con troller or signal processor switchable XO On Off Option 100V 100 volts version with 300VA toroidal transformer Option Special Colour Special finish in RAL colours SWI 112 SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual 2 3 SW 115E Short description High performance subwoofer with exponential tunnel geometry controllable with sys tem controller 1 15 long excursion chassis with double centring bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint Mounting plate with M20 thread for a distance rod mounted in the top of the speaker 2 butterfly handles non abras
11. law the owner is in charge of the disposal For these we will be happy to assist and offer you proper ways of disposal Telephone number to call about the disposal of used Kling amp Freitag products 49 511 96 99 7 0 Explanation With the ElektroG law relating to electrical and electronic equipment and appliances we have complied with the EU directive on waste electrical and electronic equipment WEEE 2002 96 EC The Kling amp Freitag AG has thus labelled all products mentioned in the WEEE from 03 24 2006 onwards with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal into the domestic waste is prohibited and that the product has been put into circulation at the 03 24 2006 earliest The Kling amp Freitag GmbH has been legally registered as a manufacturer with the registration office EAR Our WEEE Registration Nr is DE64110372 For the German Registration office EAR we have accredited that our products are sole B2B products 16 2 EU Norway Island and Liechtenstein not Germany It is not allowed to dispose of used electrical equipment as domestic waste The Kling amp Freitag AG has thus labelled all products coming from EU Member coun tries as well as Norway Island and Liechtenstein except Germany mentioned in the WEEE from 08 13 2005 onwards with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal into the domestic waste is pro
12. plug connections may already have an electrical resistance of 1 Q As a result the power amplifier cannot recognise the operations as being defective and therefore delivers unacceptable high currents In the worst case scenario this may lead to fire damage hot and charred wiring connec tors as a result of overloaded conductors and connectors etc 7he current safety regu lations are lagging behind this development and are thus not up to date with this mod ern technology In order to give consideration to this development Kling amp Freitag now equips its sub woofer systems with short circuit fuses at the signal input These fuses do not offer protection for the speaker but do reduce the risk of consequential damage in the case of a short circuit For systems which are not serially equipped with a short circuit fuse Kling amp Freitag offers simple add on kits so that you can adapt your existing subwoofer systems to the current power amplifier development 7 2 Identifying the Models with Short Circuit Fuses The subwoofer systems which are serially equipped with fire safety fuses can be identi fied as follows both mentioned stipulations must be fulfilled mo she 700W all pins parallel SER NO to out 25080000070 THAT ers Sere The first two The next two digits must be at digits must be at least 25 least 08 All subwoofer systems which are not serially equipped with short circuit fuses ca
13. 2 XO SW 115D XO or SW 118E XO can be combined with K amp F top speakers by simply connecting them in parallel 9 1 1 XO ON Subwoofer with optional Crossover XO In this mode of operation you can easily realise applications where a higher bass level is needed Be sure to use only amplifiers which can handle speaker impedances down to 3 Q in Important this mode When using the mid high systems in a cluster speakers in close proximity reduce the frequencies below 300 Hz by 3 4 dB Recommended combinations of CA systems as described here with K amp F subwoofers 2 CA systems 2 4xSW 112 XO or 2xSW 115E XO or 1 2xSW 118E XO Switch To XO ON O ox Los ee OUTPUTS INPUT e g from mixer AUX or Connector Panel O o o INPUT CH 2 INPUT CH 1 Q The switch XO on the connecting terminal of the subwoofer must be at ON for this mode of operation Switch on the subwoofers connecting terminal KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 23 of 47 User s Manual K amp F SW Series Subwoofer Systems 9 2 Operations with C2 Controller The C2 Controller optimises the operating safety of speakers and power amplifiers through special peak and RMS limiters with sense technology With other universal controllers the gain of the selected power amplifiers must be known The limiter on the C2 Controller on
14. 3 16 20 100 1000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 36 of 47 User s Manual K amp F SW Series Subwoofer Systems 14 2 SW 115E SWi 115E 14 2 1 Without optional Low Pass Filter or XO OFF SPL dB Impedance Ohm 110 316 100 100 E 9 v oa C 90 31 6 3 o cD WY Q E 80 10 70 3 15 20 100 1000 Frequency Hz 14 2 2 With optional Low Pass Filter XO ON SPL dB Impedance Ohm 110 316 100 100 i 9 u v oa c 90 31 6 3 a cD N Q E 80 10 70 i M 3 16 20 100 1000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 37 of 47 User s Manual K amp F SW Series Subwoofer Systems 14 3 SW 118E SWi 118E 14 3 1 Without optional Low Pass Filter or XO OFF SPL dB Impedance Ohm 110 316 100 100 E 9 qp pm U ea c o0 31 6 z D E 80 10 70 3 16 20 100 1000 Frequency Hz 14 3 2 With optional Low Pass Filter XO ON SPL dB Impedance Ohm 110 316 100 100 E 9 qp EM U ea c SD 90 316 S F D E
15. BH 1998 2006 Version 4 0 23 03 2006 Page 20 of 47 User s Manual K amp F SW Series Subwoofer Systems The Speaker is equipped with two parallel wired Soeakon connectors Before connecting your speaker as shown in chapter 9 be sure to switch off all con nected appliances and turn down all level controls We recommend the use of high quality speaker cables provided by KLING amp FREITAG For connections from the mixing console to the power amplifier inputs please use 2 pin shielded microphone cable with high quality connectors A Avoid ground loops see chapter 8 2 Avoiding Ground Loops Please pay attention to the respective pin diagrams in this manual Make sure that the polarity between speaker and amplifier is correct When simul taneously using power amplifiers from different manufacturers be sure to use the correct specific pin configuration It may be necessary to modify the pin configuration on the power amplifiers or on the connectors leading to them To avoid loss of power the cables should have a minimum wire gauge of 2 5 mm more for longer cabled distances A minimum wire gauge can be easily calculated with the following formula required cable lenath m TE 2 minimum wire gauge mm 2 x speaker s impedance Q Important If several loudspeakers are to be connected the signal can be linked through from one loudspeaker to the next Please make sure that the to
16. RAL 9005 structured paint Highly permeable ball proof steel grille with exchangeable black acoustic foam The subwoofer is equipped with 4 butterfly handles 4 integrated han dles K amp M mounting plate with M20 thread for a distance rod locking profiles for op tional transport cover 4 x 100 mm rear mounted transport castors 8 non abrasive plas tic stacking feet and corresponding stacking foot grooves for stacks of identical enclo sures as well as for stacks and clusters of Line 212 enclosures Optional versions Option Suspension Suspendable version with 6 flying tracks allsate Jungfalk Option Outdoor Mobile Version for mobile outdoor applications under roofs Option Special Colour Special finish in RAL colours SW 215E SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 10 of 47 User s Manual Warning K amp F SW Series Subwoofer Systems 3 Notes for the Outdoor Option Speakers with the option Outdoor Mobile and Outdoor Installation have been opti mised for outdoor use They withstand temperature fluctuations in moderate climate zones and do not accumulate condensation water In order to guarantee the longevity and safety of the speakers the speakers with the option Outdoor must still be protected from direct effects of the weat
17. are shipped with a special user s manual KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 9 of 47 User s Manual K amp F SW Series Subwoofer Systems 2 6 SWi 118E Short description High performance subwoofer for fixed installations with exponential tunnel geometry controllable with system controller Direct radiating 18 long excursion chassis bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint Highly permeable ball proof steel grille with exchangeable black acoustic foam The subwoofer is equipped with 12 concealed M12 threads for flown application or mounting devices Optional versions Option XO Version with integrated low pass filter 110 Hz for applications with or without system controller or signal processor switchable XO On Off Option Outdoor Installation Version for fixed outdoor installations under roofs Option Special Colour Special finish in RAL colours SWI 118E SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual 2 7 SW 215E Short description High performance subwoofer with exponential tunnel geometry controllable with sys tem controller 2 double centred 15 long excursion chassis bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black
18. assembly of a loudspeaker network due to simple parallel wiring The sum of the output power of the individual speakers stated as VA W must not exceed the output power of the 100 V amplifier Speakers are galvanically isolated Speakers can be integrated into existing 100 V systems 4 2 Connecting Diagram of the 100V Speaker Inputs 300VA transformer 0 all pins parallel to out KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 K amp F SW Series Subwoofer Systems Important Page 12 of 47 User s Manual Warning K amp F SW Series Subwoofer Systems 5 Instructions for Suspending the Speakers The speakers may only be suspended by trained specialised personnel with proof of their qualifications Observe the prescribed safety factors Follow the safety instructions for speakers and mounting equipment as well as the respective national rules norms and safety regulations Speaker systems whether single or connected to one another must always be secured to a second separate point even if two rigging points are used for suspending the speaker system A maximum load of 73 kg may be hung below one SW 215E subwoofer This means a maximum additional load of 36 5 kg on each flying point A maximum load of 50 kg may be suspended from the two flying points of all other subwoofers This means a maximum additional load of 25 kg on each flying point Ensure that all connections are secu
19. ding connection diagrams Please pay attention to the user s manual of your power amplifier Upon completing the wiring ensure that the connected speakers are working in phase To do so use i e a phase checker A phase error can also be recognized when the connected channels are used simultaneously During simultaneous use the bass frequencies become notably quieter or the mid frequencies such as voices cannot be located Now switch on the peripheral equipment first mixing console effects etc followed by the C2 Controller and lastly the power amplifiers Always use the before men tioned switching order Otherwise switching noises may damage the system f there is interference turn off all appliances in the reverse order and check all cable connections see chapter 8 2 Avoiding Ground Loops Next turn on the C2 Controller if used and the other peripheral equipment and make sure there is no interference Important Now put a low level signal into the system and check for the correct function of the system In doing so all amplifier input controls need to be turned down again Now turn on the amplifier s level control for the left CA system and check that the correct signal is coming out of the top speaker For operations with C2 Controller The Sense LED for the top speaker i e CH 1 TOP signal of the K amp F C2 Controller will light up green at a level of at ca 40dB The other channels of
20. for speakers and assembly equipment For mobile and fixed installations use only rigging equipment from KLING amp FREITAG Make sure to observe the included safety and mounting instructions for loudspeakers and accessories Speakers and rigging equipment must be visually examined at regular intervals If there are signs of wear they must be replaced immediately Furthermore screwed connec tions of supporting parts must be checked routinely Warning Protecting the Speakers In general audio signals should not be overdriven This may be caused by mixing consoles equalizers effect equipment etc and should be indicated on this equipment When a power amplifier is overloaded at the output clipping then the amplifier should activate a clipping warning signal Power amplifiers can also be overloaded at the input circuit without the amplifier signalling the clipping i e when there is not sufficient headroom in the input cir cuit We therefore recommend turning up the power amplifiers all the way and adjusting Important the level before the power amplifier in order to avoid overloading the input circuit In any case the signal must be reduced as soon as it sounds unnaturally distorted To protect the speakers from being destroyed and to avoid fire hazard they should only be operated with professional power amplifiers with the following specifica tions integrated clipping limiter without using a Kling amp Freitag con
21. ge may be loosened at a time If both screws of an enclosure edge become loose then for safety reasons the L bracket will collapse into the enclosure If the L bracket has fallen into the enclosure the loudspeaker must on no ac count be used again until it has been repaired by an authorized repair service When mounting the speakers use only fastening mechanisms with threads that extend at least 35 mm into the speaker enclosure Take into account the permissible load ca pacity of the fastening mechanisms while considering the safety factors Mount the speakers using at least two independently operating points Secure all screws to prevent loosening NN f 35 mm minimum Always use flat was hers M12 with the customary outer dia meter of 37 mm l Loosen only one of these two screws at a time KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Warning Page 14 of 47 User s Manual K amp F SW Series Subwoofer Systems 5 3 Subwoofers with allsafe JUNGFALK Flying Points E PM f dai j Vuh m n j fA Ce Ay oU o 2 alo PA ipa lt A ii 2 A TA EPR 44 MY b f 4 4 CA 4 at t f LJ gt d D P URP o ir Single Stud Fitting Flying Point Used as fastener to the allsafe Receptacle for special fasteners JUNGFALK flying Point Take the single stud fitting in one and push the locking device up hand against the spring tension 3 4 Pu
22. ghtly Warning KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 16 of 47 User s Manual Warning Caution K amp F SW Series Subwoofer Systems 6 Mounting Instructions for Speakers Mount the speakers securely To avoid injury or damage always be sure to mount the speakers securely so that they do not fall Soeakers which are stacked must be secured with securing straps When laying the connecting cables make sure that nobody can trip The stability of stacked systems also valid for the use of stands and distance rods is contingent upon the following stability requirement These conditions must therefore be guaranteed by the user Stacked systems may not fall over even if they are inclined by 10 in each direc tion If this requirement is not fulfilled then it is necessary to take steps to achieve compliance Possible measures include strapping it to an appropriate base structure or fastening it using safety straps 6 1 Using the Mounting Equipment Distance Rod The subwoofer is equipped with a threaded flange M20 on the top of the enclosure for mounting the optionally available distance rod not on the SWi versions All K amp F top speakers with a mounting flange or stand adapter may be mounted on the distance rod Only use authentic Kling amp Freitag distance rods and stand adapters We can only guarantee safe operations when these parts are used When a top speaker is m
23. her They should be installed for example under a roof so that they also have sufficient protection from driving rain from the side and direct sunlight 3 1 Outdoor Mobile Version for mobile outdoor use under roofs Features like standard version but with the following extras multi layered temperature and UV resistant high tech PU marine primer final coating with highly resistant structured 2K paint in RAL colours waterproofed diaphragms and electronic components protected against cor rosion with protective coating 3 2 Outdoor Installation Version for fixed installations under roofs Features like standard SWi version combined with Outdoor Mobile but with the following extras stainless steel grille acoustic foam behind grille visible screws made of stainless steel stainless steel connecting terminal with single PG cable fitting 13 mm Wiring bl blue bn brown KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 11 of 47 User s Manual 4 Notes for the SW112 SWi 112 with Option 100V Kling amp Freitag speakers with 100V option are fitted with high quality toroidal trans formers This serves to minimize loss of sound Highly professional sound reinforcement results can be achieved by using 100 V Kling amp Freitag speakers 4 1 Reasons for choosing Speakers with 100 V Technology Reduction in conduction loss Easy
24. hibited and that the product has been put into circulation at the 08 13 2005 earliest Unfortunately the European directive WEEE has been complied with implementing different national provisions of law throughout all member countries which makes it impossible for us to offer consistent solutions for the disposal throughout Europe Responsible for complying with these provisions of law is the local distributor importer of each country For proper disposition of used products in accordance with these local provisions in the mentioned countries of the European Union except Germany please ask your local dealer or the local authorities 16 3 Other countries For proper disposition of used products in accordance with local provisions in other countries please ask your local dealer or the local authorities KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 47 of 47
25. ications with or without system controller switchable XO On Off Option Special Colour Special finish in RAL colours SWI 115E SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual 2 5 SW 118E Short description High performance subwoofer for mobile use with exponential tunnel geometry control lable with system controller Direct emitting 18 long excursion chassis bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint Highly permeable ball proof steel grille with exchangeable black a coustic foam The subwoofer is equipped with 2 butterfly handles K amp M mounting plate with M20 thread for a distance rod locking profiles for optional transport cover 4 all safe Jungfalk flying points for suspension 4 x 100 mm rear mounted transport castors non abrasive plastic stacking feet and corresponding stacking foot grooves for stacks of identical enclosures Optional versions Option XO Version with integrated low pass filter 110 Hz for applications with or without system controller or signal processor switchable XO On Off Option Outdoor Mobile Version for mobile outdoor applications under roofs Option Special Colour Special finish in RAL colours SW 118E SP Version with integrated power amplifier technology SP speakers
26. in 6 Q 2 x Speakon NLAMP 1 4 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU ball proof steel grille with exchangeable black acoustic foam 12 x M 12 thread inserts 600 x 672 x 640 mm 46 2 kg XO switchable low pass filter terminal clamp instead of Speakon connector Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field Version 4 0 23 03 2006 Page 34 of 47 User s Manual 13 7 SW 215E Speaker Design Frequency range 10 dB Frequency range 3 dB Crossover frequencies Power handling Sensitivity 1 W 1m Max SPL Components Impedance nominal Connectors Enclosure Dimensions W x H x D Weight Options Accessories K amp F SW Series Subwoofer Systems Bass reflex system with exponential tunnel geometry 36 Hz 1 kHz 42 Hz 250 Hz max 200 Hz 1500 W nominal 3000 W programme 98 dB 42 Hz 150 Hz 133 dB peak 1 m free field equivalent 139 dB half room 2 x 15 long excursion chassis 100 mm voice coil with double centring internal and external ventilation Demodulation ring double DDR for minimal distortions 4 Q Zmin 3 1 Q 2 x Speakon NLAMP 1 1 15 mm frame reinforced Multiplex plywood with highly resistable black structured paint PU 4 ergonomic butterfly handles
27. in combination with option XO Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field Version 4 0 23 03 2006 Page 30 of 47 User s Manual 13 3 SW115E Speaker Design Frequency range 10 dB Frequency range 3 dB Power handling Sensitivity 1 W 1m Max SPL Components Impedance nominal Connectors Enclosure Dimensions W x H x D Weight Options Accessories K amp F SW Series Subwoofer Systems Bass reflex system with exponential tunnel geometry 3 Hz 320Hz 43 Hz 150 Hz 750 W nominal 1500 W programme 95 dB 37 Hz 320 Hz 127 dB SPL Peak 1 m free field equivalent 133 dB half room 15 long excursion chassis double centred 100 mm voice coil internal and external ventilation Aluminium demodulation ring for minimal distortions 8 Q Zmin 6 2 Q XO OFF or without filter 6 Q Zmin 4 5 Q XO ON 2 x Speakon NLAMP 1 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU 2 ergonomic butterfly handles K amp M mounting plate M20 for distance rod 4 non abrasive plastic sliders stacking foot grooves for stacks of identical enclosures or SW 215E as well as Line 212 2 locking profiles for optional transport cover ball proof steel grille with exchangeable black acoustic foam 470 x 515 x 640 mm 35 kg 37 kg with
28. ith option XO XO switchable low pass filter crossover frequency at 110 Hz barrier strip instead of speakon connector Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field Version 4 0 23 03 2006 Page 32 of 47 User s Manual K amp F SW Series Subwoofer Systems 13 5 SW 118E Speaker KLING amp FREITAG GMBH 1998 2006 Design Frequency range 10 dB Frequency range 3 dB Crossover frequencies Power handling Sensitivity 1 W 1m Max SPL Components Impedance nom XO ON without filter or XO OFF Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories Version 4 0 23 03 2006 Bass reflex system with exponential tunnel geometry 30 Hz 2 5 kHz 38 Hz 300 Hz 110 Hz with optional low pass filter XO ON 700 W nominal 1400 W programme 97 dB 40 Hz 300 Hz 134 dB SPL peak 1 m free field equivalent 140 dB half room 18 long excursion chassis double centred 100 mm voice coil internal and external ventilation demodulation ring double DDR for minimised distortions 6 Q Zmin 4 Q 8 O Zmin 6 Q 2 x Speakon NLAMP 1 4 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU 4 ergonomic butterfly handles K amp M mounting plate M20 for distance rod 4 non abrasive plastic fee
29. ive plastic stacking feet and corre sponding stacking foot grooves for stacks of identical enclosures or SW215E and Line 212 enclosures Locking profiles for optional transport cover highly permeable ball proof steel grille with exchangeable black acoustic foam Optional versions Option XO Version with integrated low pass filter 110 Hz for applications with or without system controller switchable XO On Off Option Outdoor Mobile Version for mobile outdoor applications under roofs Option Special Colour Special finish in RAL colours SW 115E SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 8 of 47 User s Manual K amp F SW Series Subwoofer Systems 2 4 SWi 115E Short description High performance subwoofer with exponential tunnel geometry controllable with sys tem controller 1 15 long excursion chassis with double centring bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint Highly permeable ball proof steel grille with exchangeable black a coustic foam The subwoofer is equipped with 12 concealed M12 threads for flown applications or for mounting devices Optional versions Option XO Version with integrated low pass filter 110 Hz for appl
30. ived from Kling amp Soca Freitag to the top side of the main bar SPEAKERS WITH CUCK amp FLY MAINBARS Receipt of a written version of this manual for each Click amp Fly System User s Manual made available for the user Disposal of the old Users Manual Kling amp Freitag GmbH has made all resources necessary for supplementation including a detailed manual available free of charge to all buyers of the old CLICK amp FLY RIGGING SYSTEM If you did not receive these resources please contact your retailer KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 13 of 47 User s Manual K amp F SW Series Subwoofer Systems 5 2 Subwoofers with Flying Thread M12 SWi Versions If you want to use the SP subwoofers equipped with flying threads M12 please read the following instructions Appropriate fastening mechanisms with an external screw thread of M12 and a mini mum length of 35 mm may be screwed on to the M 12 thread inserts The internal screw threads in the speaker enclosure are fastened during production with counter sunk head screws M12 The two internal screw threads of the inner enclosure edge are on an L bracket This L bracket has the function of connecting the adjoining plates of the enclosure It provides sufficient tensile strength for flown operations To guarantee that the enclosure plates are correctly connected by the L brackets only one screw of the enclosure ed
31. mp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 4 of 47 User s Manual K amp F SW Series Subwoofer Systems Chapter Page 9 Configurations and Connecting Diagrams 23 9 1 Operating the Systems without C2 Controller 23 9 1 1 XO ON Subwoofer with optional Crossover XO 23 9 2 Operations with C2 Controller 24 9 2 1 XO OFF or Subwoofers without optional Crossover 25 10 Operating the Speakers 26 11 Internal Wiring of Subwoofers with Low Pass Filter XO 27 11 1 SW 112 XO SW 118E XO 2 11 2 SW 115E XO 28 12 Touching Up Damage to Paint Changing the Front Foam 28 13 Technical Specifications 29 13 1 SW 112 29 13 2 SWi 112 30 13 3 SW 115E 31 13 4 SWI 115E 32 13 5 SW 118E 33 13 6 SWI 118E 34 13 7 SW 215E 35 14 Frequency Diagrams 36 14 1 SW 112 SWi 112 36 14 1 1 Without optional Low Pass Filter or XO OFF 36 14 1 2 With optional Low Pass Filter XO ON 36 14 2 SW115E SWi 115E 37 14 2 1 Without optional Low Pass Filter or XO OFF 37 14 2 2 With optional Low Pass Filter XO ON 37 14 3 SW 118E SWIi 118E 38 14 3 1 Without optional Low Pass Filter or XO OFF 38 14 3 2 With optional Low Pass Filter XO ON 38 14 4 SW 215E 39 15 Dimensions 40 15 1 SW 112 40 15 2 SWI 112 41 15 3 SW 115E 42 15 4 SWI 115E 43 15 5 SW 118E 44 15 6 SWI 118E 45 15 7 SW 215E 46 16 Regulations for Disposal 47 16 1 Germany 47 16 2 EU Norway Island and Liechtenstein not Germany 47 16 3 Other countries 47
32. n be if required easily and inexpensively upgraded even by yourself An instruction manual for this upgrade is delivered with the add on kit 7 3 Specification of the Fuses The fuses in all models have the following identical specifications Bussmann S 506 8A slow When necessary these fuses may only be replaced with the aforementioned original fuse KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 19 of 47 User s Manual K amp F SW Series Subwoofer Systems 7 4 Replacement and Positions of the Short Circuit Fuses When the fuse is burned out then the chassis is most likely already ruined as the fuse just prevents consequential damage resulting from a short circuit of the chassis A disassembly of the chassis is therefore unavoidable 7 4 1 Subwoofers without Crossover XO The fuse holder of the subwoofers without a crossover XO is mounted on the signal wiring behind the input connector The subwoofers with two chassis have 2 fuses be cause the chassis are intended for parallel use When replacing the fuse the chassis must be removed in order to reach the fuse holder Unscrewing the connecting terminal does not enable you to reach the fuse holder When the chassis is re assembled first loosely fasten the screws diagonal from one another then tighten them By tightening the screws diagonally in two steps a defor mation of the chassis and thus a possible de centring of the voice coil can be avoided
33. ns may cause minor injuries or cause property damage Caution This symbol gives instructions for the proper use of the described prod ucts Not following these instructions may cause malfunctions or prop erty damage Important Information about this User s Manual User s Manual K amp F SW Series Subwoofer Systems version 4 0 23 03 2006 O by Andr Figula Kling amp Freitag GmbH 1998 2006 all rights reserved All specifications in this manual are based on information available at the time of pub lishing for the features and safety guidelines of the described products Technical specifications measurements weights and properties are not guaranteed The manufacturer reserves the right to make product alterations within legal provisions as well as changes to improve product quality All persons who use the speaker system must have this guide and all further in formation for safe operations available to them during assembly disassembly and use We appreciate any input with suggestions and improvements for this manual Please send this to us at the following address info kling freitag de or to KLING amp FREITAG GMBH Junkersstr 14 D 30179 Hannover Phone 49 0 511 96 99 70 Fax 49 0 511 67 37 94 KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 3 of 47 User s Manual K amp F SW Series Subwoofer Systems Chapter Page 1 General Safety Instructions for Using Speakers 6 2 Prod
34. option XO XO with switchable low pass filter Crossover frequency at 110 Hz barrier strip instead of speakon connector Outdoor Mobile Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 31 of 47 User s Manual K amp F SW Series Subwoofer Systems 13 4 SWi 115E Speaker Design Frequency range 10 dB Frequency range 3 dB Power handling Sensitivity 1 W 1m Max SPL Components Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 1998 2006 Bass reflex system with exponential tunnel geometry 37 Hz 320 Hz 43 Hz 150 Hz 750 W nominal 1500 W programme 95 dB 37 Hz 320 Hz 127 dB SPL Peak 1 m free field equivalent 133 dB half room 15 long excursion chassis double centred 100 mm voice coil internal and external ventilation Aluminium demodulation ring for minimal distortions 8 Q Zmin 6 2 Q XO OFF or without filter 6 Q Zmin 4 5 Q XO ON 2 x Speakon NLAMP 1 4 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU ball proof steel grille with exchangeable black acoustic foam 12 x M12 thread inserts 470 x 504 x 640 mm 35 3 kg 37 3 kg w
35. ounted on the subwoofer using a distance rod the stability of the speakers is reduced Please follow the stability requirements in chapter 6 When re positioning after set up remove the upper speaker mounted on the distance rod first Special note for the model SW 112 A top speaker with a maximum weight of 28 kg i e CA 1201 may be mounted on this speaker using a distance rod Speakers which are heavier than 28 kg may not be mounted on the distance rod flange and must be mounted on an additional speaker stand a a Distance rod 334 Distance rod 337 Distance rod 337 adjustable with stand adapter and adjustable speaker mount KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 17 of 47 User s Manual K amp F SW Series Subwoofer Systems 6 2 LINE 212 Systems on Top of SW 115E Stapelmulden f r SW 115E In addition to the stacking foot grooves for stacking the same enclosures the subwoofer SW 115E also has stacking foot grooves for the Line 212 system One Line 212 System can be quickly and safely positioned on top of the subwoofer Stapelmulden f r LINE 212 Stapelmulden f r LINE 212 und SW 115E 6 3 LINE 212 Systems on Top of SW 215E E Es x In addition to the stacking foot grooves for stacking the same enclosures the subwoofer SW 215E also has stacking foot grooves for the Line 212 system
36. read Inserts M12 196 L 9 OI UU 9 6op I WW ZOZ 9S8t 97 WW 9 250 2 mm Version 4 0 23 03 2006 Page 45 of 47 K amp F SW Series Subwoofer Systems User s Manual SW 215E 15 7 Son004b bubpeIs CLE INI JO Son004b bubpeIs DOJ DULJSIP JO e1ejd Buixi V0S 8L 7S0 S 261 Sc uw oz T WW SLOL O OQ CLT JNN 4epeads V 10 S9 0040 1 SN D S9A004b buDpeIs sJopi s Dnsejd uoisuedsns uodo ui JUO ejbunr ayesyje ype Bulls SNOISN3INIG Page 46 of 47 Version 4 0 23 03 2006 KLING amp FREITAG GMBH 1998 2006 User s Manual K amp F SW Series Subwoofer Systems 16 Regulations for Disposal 16 1 Germany It is not allowed to dispose of used electrical equipment as domestic waste But please do not dispose of them at official collecting points for recycling either All Kling amp Freitag products are plain business to business B2B products Disposal of Kling amp Freitag products labelled with a waste bin sign have thus to be disposed of by Kling amp Freitag alone Please call Kling amp Freitag at the number stated below if you have a Kling amp Freitag product to be disposed We will offer you a straightforward and professional disposal not affecting costs If there is no dustbin sign on one of your Kling amp Freitag products because they have been sold before March 2006 then by
37. red to prevent their detaching on their own and that only admissible statically tested and sufficiently sized mounts connecting devices ropes and chains are used 5 1 SW 215E and Click amp Fly Accessories The Click amp Fly rigging system is a certified and type tested rigging system for safe and comfortable rigging of SW 215E or Line 212 systems Click amp Fly Systems with the classification of CLICK amp FLY RIGGING SYSTEM may not be used with the SW 215E Systems without the supplementary measures described below This is necessary due to safety measures for the subwoofer system which have become additionally necessary Only when these new supplementary measures are observed can it be guaranteed that you will have a safe and accordingly certified product for your further use oo etiam a AP Aa At this position LINE 212 SW 215E must be Manufacturing Year 2004 visible If RIGGING SYSTEM is present at this KUNGEN SW Load 135 0kg FREITAS Weight 3 3kg position then the Click amp Fly rigging systems is only approved for use with the Line 212 sys tems Ser NOo XXXXXXXXXXX Made in Germany Supplementary measures which allow for an old Click amp Fly rigging system to be used for mounting SW 215E Systems Affix a new name plate available from Kling amp Freitag recognisable by the classi fication CLICK amp FLY LINE 212 SW 215E Affix the following additional sticker rece
38. t 4 stacking foot grooves for stacks of identical enclosures 2 locking profiles for optional transport cover ball proof steel grille with exchangeable black acoustic foam 4 flying points allsafe JUNGFALK 600 x 680 x 766 mm incl castors 49 8 kg XO with switchable low pass filter terminal clamp instead of Speakon connector without 100 mm transport castors Outdoor Mobile Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field Page 33 of 47 User s Manual K amp F SW Series Subwoofer Systems 13 6 SWi118E Speaker Design Frequency range 10 dB Frequency range 3 dB Crossover frequencies Power handling Sensitivity 1 W 1m Max SPL Components Impedance nom XO ON without filter or XO OFF Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 1998 2006 Bass reflex system with exponential tunnel geometry 30 Hz 2 5 kHz 38 Hz 300 Hz 110 Hz with optional low pass filter XO ON 700 W nominal 1400 W programme 97 dB 40 Hz 300 Hz 134 dB SPL peak 1 m free field equivalent 140 dB half room 18 long excursion chassis double centred 100 mm voice coil internal and external ventilation demodulation ring double DDR for minimised distortions 6 Q Zmin 4 Q 8 O Zm
39. t the flat head of the holding Release the locking device when bolt into the guiding of the flying the single stud fitting is located in point the middle of the flying point Make sure that the locking device clicks into place 5 Warning Check that the single stud fitting is securely fastened and cannot be pulled out KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 15 of 47 User s Manual K amp F SW Series Subwoofer Systems 5 4 SW 215E Suspension Using the allsafe Flying Track The subwoofer SW 215E with suspension option may only be suspended by using the double stud fittings available from Kling amp Freitag The allsafe JUNGFALK flying tracks are used to suspend the SW 215E system We recommend using the BGV C1 certified Click amp Fly Line 212 SW 215E rigging sys tem for suspending the SW 212E The allsafe JUNGFALK flying track can only support weights up to 73 kg on one point Please follow the accompanying safety and assembly instructions carefully Double Stud Fitting allsafe JUNGFALK Flying Track Used as fastener to the allsafe Receptacle for the double stud fit JUNGFALK Flying Point and the ting allsafe JUNGFALK Flying Track 1 Align the double stud fitting as Slide the pushed double stud fitting shown above and push it into the to the middle of the speaker until it track clicks into place Make sure that it is secured ti
40. tal impedance of the loudspeakers R Q is not lower than the minimal impedance indicated on the power amplifier VR 1 R 1 R 1 R total 8 1 Connecting the Speakon Connectors to the Connecting Terminal KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 21 of 47 User s Manual K amp F SW Series Subwoofer Systems 8 2 Avoiding Ground Loops 8 2 1 What is a Ground Loop Every component of a P A or Hi Fi System has its own internal OV reference ground This point is often connected to the protective earth connector PE Ground If two or more units are connected to one another with a line level audio cable there may be a ground connection through the ground of the power supply cable yellow green as well as through the shielding of the audio cable The voltage difference between these two ground points causes audible interference to come from the speaker 8 2 2 Avoiding Ground Loops If there is a loud humming or buzzing after the speaker has been connected then check that a ground loop has not been built into the system Some power amplifiers and system controllers facilitate a ground lift switch Set these ground lift switches to the Lift position one after the other If the noise is still audible check if 1 the noise is caused by a ground loop before the power amplifiers or controllers e g mixing console effects or equalizers 2 the system or parts of the system are connec
41. ted to an unclean power supply meaning one which is also running large motors or lighting systems An un clean supply voltage electrostatic and electromagnetic fields can cause inter ference Please observe the following basic rules Never try to avoid a ground loop by disconnecting or taping the protec tive earth contact at the mains connector Extremely dangerous Extremely dangerous f possible only use high quality audio appliances with balanced signal outputs and with power cables with PE connectors Use high quality cables with good shielding The point of ground for all connected components should merge at one central point The power connections should lead out in a radial manner from one point and not be linked from one unit to the next When installing appliances that create strong electrostatic or electromagnetic fields large transformers switch mode power supplies maintain some distance from other audio appliances In extreme cases the only solution is to create a completely independent audio ground in other cases it is sufficient to connect a filter in front of the audio equipment KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Warning Page 22 of 47 User s Manual K amp F SW Series Subwoofer Systems 9 Configurations and Connecting Diagrams 9 1 Operating the Systems without C2 Controller The K amp F subwoofers with integrated crossover SW 11
42. the other hand uses a special control circuit to determine the actual output voltage of the power amplifiers The limiter then reduces the input level only when the power amplifier actually provides more power than the speakers can handle The amplifier s gain and the position of the input level control for the power amplifiers are insignificant for the limiter function of the C2 Controller C2 Power amplifier with Controller input level control Measured value Output voltage of the power amplifier Universal Power amplifier with Controller input level control Fixed value depending on the gain and the position of input level controls of the power amplifier Additional features of the C2 Controller The use of carefully adjusted filters EQ on the system plug in cards enables the C2 Controller to optimise the feedback stability and the frequency response of the speak ers It provides a level alignment for the bass speakers and a sub mono function The following functions are available for the top speakers optional bass boost in full range mode optimisation for clustered applications Top Low Cut switch high boost for larger distances KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 24 of 47 User s Manual K amp F SW Series Subwoofer Systems 9 2 1 XO OFF or Subwoofers without optional Crossover Operations with Controller C2 in 2 way active mode
43. the system are checked in the same way If the wrong LED lights up or a wrong i e in 2 way active mode low signal from a high frequency speaker or dis torted signal occurs then there is a mistake in the wiring KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 26 of 47 User s Manual K amp F SW Series Subwoofer Systems 11 Internal Wiring of Subwoofers with Low Pass Filter XO 11 1 SW 112 XO SW 118E XO Short circuit fuse l en Bussmann S 506 8A slow IN LF Only if serially equipped with short circuit fuse DC PETIT KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 27 of 47 User s Manual K amp F SW Series Subwoofer Systems 11 2 SW 115E XO o NI NI O Short circuit fuse Bussmann S 506 8A slow O EEVT 12 Touching Up Damage to Paint Changing the Front Foam Although the PU structured paint used by KLING amp FREITAG is extremely resistant we recommend using protective covers or cases to help avoid damaging the paint during i e continuous mobile use If paint damage occurs despite these precautions it can be touched up by using commercial acrylic paint in the appropriate RAL colour of the speaker To replace the filter foam send the front grille incl foam to KLING amp FREITAG GmbH Upon payment for expenses the grille with the new covering will be returned KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 28 of 47
44. troller Integrated or preceding subsonic filter approx 20 Hz min 12 dB octave For damage caused by overloading or use with power amplifiers other than those rec ommended above Kling amp Freitag GmbH does not assume warranty and excludes liabil ity for possible consequential damage The following signals may damage the speakers permanent high pitched signals with high frequency and continuous noise from feedback permanently distorted signals with high power noises which occur when the amplifier is on while equipment is being connected disconnected or switched on Do not install devices in any of the following places where the devices are permanently exposed to direct sunlight where the devices are exposed to high moisture where the devices are exposed to strong vibrations and dust KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 6 of 47 User s Manual K amp F SW Series Subwoofer Systems Damage caused by the speakers magnetic fields Speakers are permanently surrounded by a magnetic field even when they are not oper ating Therefore during transport and placement of the speakers it is important to ensure that there is always approx 1 m between the speakers and magnetic data media Important and computer video monitors Preventing hearing damage To prevent the risk of hearing damage avoid being too close to operating speakers even if the volume level seems to be lo
45. ts allsafe JUNGFALK Outdoor Mobile Special finish in RAL colours see catalogue or visit www kling freitag de 1 Pink noise 40 400 Hz 2 h 2 as 1 but with 50 duty cycle 3 2 83 Vrms free field KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 29 of 47 User s Manual K amp F SW Series Subwoofer Systems 13 2 SWi112 Speaker Design Frequency range 10 dB Frequency range 3 dB Crossover frequencies Power handling Sensitivity 1 W 1m Max SPL Components Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 1998 2006 Bass reflex system with exponential tunnel geometry 35 Hz 2 5 kHz 41 Hz 350 Hz 110 Hz with optional low pass filter XO ON 500 W nominal 1000 W programme 92 dB 45 Hz 350 Hz 124 dB SPL Peak 1 m free field equivalent 130 dB half room 12 long excursion chassis 100 mm voice coil internal and external ventilation 6 Q Zmin 4 Q XO ON 8 Q Zmin 6 Q XO OFF 2 x Speakon NLAMP 1 1 15 mm frame reinforced Multiplex plywood with highly resistant black structured paint PU ball proof steel grille with exchangeable black acoustic foam 12x M 12 thread inserts 470 x 370 x 520 mm incl castors 27 kg XO switchable low pass filter terminal clamp instead of Speakon connector 100 Volt with 300 VA toroidal transformer 29 5 kg not
46. uct Descriptions and Versions 7 2 1 SW 112 2 2 SWI 112 8 2 3 SW 115E 8 2 4 SWI 115E 9 2 5 SW 118E 9 2 6 SWi118E 10 2 SW 215E 10 3 Notes for the Outdoor Option 11 3 1 Outdoor Mobile 11 3 2 Outdoor Installation 11 4 Notes for the SW112 SWi 112 with Option 100V 12 4 1 Reasons for choosing Speakers with 100 V Technology 12 4 2 Connecting Diagram of the 100V Speaker Inputs 12 5 Instructions for Suspending the Speakers 13 5 1 SW 215E and Click amp Fly Accessories 13 5 2 Subwoofers with Flying Thread M12 SWi Versions 14 5 3 Subwoofers with allsate JUNGFALK Flying Points 15 5 4 SW 215E Suspension Using the allsafe Flying Track 16 6 Mounting Instructions for Speakers 17 6 1 Using the Mounting Equipment Distance Rod 17 6 2 LINE 212 Systems on Top of SW 115E 18 6 3 LINE 212 Systems on Top of SW 215E 18 7 Short Circuit Fuses in the K amp F Subwoofer Systems 19 7 1 Risks of using High Performance Power Amplifiers 19 7 2 Identifying the Models with Short Circuit Fuses 19 7 3 Specification of the Fuses 19 7 4 Replacement and Positions of the Short Circuit Fuses 20 7 4 1 Subwoofers without Crossover XO 20 7 4 2 Subwoofers with Crossover XO 20 7 5 Add On Kits for Subwoofers without Short Circuit Fuses 20 8 Wiring 21 8 1 Connecting the Soeakon Connectors to the Connecting Terminal 21 8 2 Avoiding Ground Loops 22 8 2 1 What is a Ground Loop 22 8 2 2 Avoiding Ground Loops 22 KLING a
47. w enough In general volume levels over 90 dB can cause hearing damage Caution 2 Product Descriptions and Versions 2 1 SW 112 Short description Ultra compact high performance subwoofer for mobile use with exponential tunnel geometry controllable with system controller direct emitting 12 long excursion chas sis bass reflex tuning Enclosure Frame reinforced Finnish Multiplex enclosure with highly resistant black RAL 9005 structured paint highly permeable ball proof steel grille with exchangeable black acoustic foam The subwoofer is equipped with a handle K amp M mounting plate with M20 thread for a distance rod non abrasive plastic stacking feet and corresponding stacking foot grooves for stacks of identical enclosures Optional versions Option XO Version with integrated low pass filter 110 Hz for operations without system con troller or signal processor switchable XO On Off Option Suspension Suspendable version with 6 flying points allsafe Jungfalk Option 100V 100 volts version with 300VA toroidal transformer Option Outdoor Mobile Version for mobile outdoor applications under roofs Option Special Colour Special finish in RAL colours SW 112 SP Version with integrated power amplifier technology SP speakers are shipped with a special user s manual KLING amp FREITAG GMBH 1998 2006 Version 4 0 23 03 2006 Page 7 of 47 User s Manual
Download Pdf Manuals
Related Search