Home

Manual

1. LRP electronic GmbH 2009 NEW STOGKSPEG MAGNET HVS TECHNOLOGY PRECISENSOR SYSTEM FASY TEGH FEATURES X12 cm ftockSpec USER GUIDE Ler 1 7 E ME BLUE IS BETTER LRP electronic GmbH Wilhelm Enssle Str 132 134 73630 Remshalden Germany info LRP cc www LRP cc WARNING NOTES AX Do not use aggressive advanced timing speed control profiles with X12 StockSpec motors Because of it s unique design with HVS Technology and PrecisSensor System such profiles are not required to gain same performance as normal motors with extreme speed control timing advance and with X12 StockSpec such profiles only result in higher motor temperature but not higher performance So when using an X12 StockSpec motor with our SPX StockSpec speed control we recommend not using profiles 7 and 8 No toy Not suitable for children under 14 years Keep the product out of the reach of children Pay close attention to the following points as they can destroy the product and void your warranty Non observance of these points can lead to property damage personal and severe injuries Never leave the product unsupervised while it is switched on in use or connected with a power source If a defect occurs it could set fire to the product or the surroundings Avoid incorrect connections or connections with reversed polarity of the product All wires and connections have to be well insulated Short circuits can possibly destroy the product Never allo
2. if available before you send in this product for repair If products are sent in for repair which do operate perfectly we have to charge a service fee according to our pricelist With sending in this product the customer has to advise LRP if the product should be repaired in either case If there is neither a warranty nor guarantee claim the inspection of the product and the repairs if necessary in either case will be charged with a fee at the customers Dear Customer thank you for your trust in this LRP product By purchasing a LRP VECTOR X12 StockSpec brushless motor you have chosen the highest developed competition brushless motor LRPs R amp D team took all the experience and testing results from the last 4 years of practical tests and racing with the LRP brushless motors on the highest levels of competition IFMAR World Champion Technology Please read the following instructions carefully before you start using your motor This user guide contains important notes for the installation the safety the use and the maintenance of this product Thus protecting yourself and avoid damages of the product Proceed according to the user guide in order to understand your motor better Please take your time as you will have much more joy with your product if you know it exactly This user manual shall be kept in a safe place If another customer is using this product this manual has to be handed out together with it TECHNICAL DATA 21 5T
3. 17 5T 13 5T 10 5T 9 5T Voltageinput wy TV S O Rem 1220 15840 2190 25920 28800 Specific RPM V kv 1700 2200 3o50 3600 f 4o00 Power iw us 183 2m 3 Sintered 12 45mm StockSpec 50635 Winding ssid Star Multistrand Copper Winding Compliant to IFMAR EFRA ROAR FEMCA JMRCA BRCA DNC rules Specifications subject to change without notice Measured at 7 2V GEARING A wrong gear ratio causes excessive heating and may result in motor damage or thermal shutdown of your speed control Take your kits manual to find the correct pinion Motor temperatures should be monitored when you re on a new track use a new motor or make a massive gear change Motor temperature should never exceed 100 C 210 F The following gear ratios are only a recommendation and a good starting point The actual gearing may vary due to different speed controls speedo profiles motor timings tracks track conditions and batteries USAGE Volts 21 5T 17 5T 13 5T 10 5T 9 5T Touring Car 7 4 35 1 40 1 60 1 65 1 9 6o 55 1 60 1 1 12 48 2wd 4wd Off Road 7 4 55 1 60 1 70 1 80 1 90 1 Truck Off Road 7 4 90 1 10 0 1 65 1 70 1 80 1 DISASSEMBLY Due to the maintenance free design of the Vector X12 StockSpec it is not necessary to open the motor frequently under normal conditions It is just recommended to check that all screws are still securely fastened Nevertheless it is
4. recommended that you frequently maintain clean check oil replace if needed the ball bearings in order to achieve best performance Of course you can also disassemble the motor entirely if you wish to do so Disassemble the motor 1 Loosen the center endcover screw and remove screw plastic endcover and timing insert 2 Remove PreciSensor Assembly by pulling gently at sensor connector 3 Loosen and remove the long outer 3 screws and gently slide off the front aluminium housing 4 Remove the o ring and shim from the shaft 5 Carefully pull the rotor out of the housing and place it in clean towel or designated rotor container 5 You have now access to both ball bearings for cleaning maintenance and replacement You may also use compressed air to clean the inside of the motor after you have removed the bearings Be careful with correct shim o ring position during re assembly and avoid overtightening the screws Endcover Timing PreciSensor Insert Assembly Stack Rotor Shim M2 2 x 43 M2x6 Front Housing SPARE AND OPTIONAL PARTS Spare parts 50627 50635 50622 50623 X12 StockSpec 694ZZ ABEC5 Ball Bearings 2pcs X12 StockSpec Sintered Rotor X12 Small Parts Set includes screws endcover timing inserts shims o ring X12 PreciSensor Assembly complete replacement sensor assembly ready to use Optional parts 50632 50632 50634 50625 50626 819307 819310 819315 819320 X12 Modified Tuning Rotor Sin
5. enient replacement of the power wires Nevertheless some soldering skills are required Talk to your local hobbyshop if you are concerned about soldering the wires yourself Caution Avoid soldering longer then 5sec per soldering joint to prevent possible damage to the motor due to overheating of the inner components e Install the motor in the model Caution The maximum length of the motor screws shall not exceed 8mm e Connect the power wires of the speed control to the motor Make sure that the sequence is correct by checking the color code and the letters MOT A blue wire MOT B yellow wire MOT C orange wire e f you re using a sensored speed control at tach the hall sensor wire to motor and speedo now e Finally check all the connections before using the motor Hall Sensor wire PRECISENSOR SYSTEM LRP s world exclusive PreciSensor System allows precise control for best and most efficient performace Fast simple and super accurate timing adjustment using the supplied timing inserts By altering the timing you move the powerband and alter the characteristics of the motor Three important things to remember about timing adjustments 1 Higher timing results in higher rpm but worse efficency torque and vice versa 2 Higher timing requires shorter gearing 3 Timing adjustments should be done by experienced racers only others please leave timing on standard setting To alter the timing proceed as follo
6. or repairs or exchanges the product e Shipment back to you usually by COD cash on delivery but this is subject to your national LRP distributor s general policy
7. tered 12 0mm X12 Modified Tuning Rotor Sintered 12 5mm X12 Modified Tuning Rotor Sintered 13 0mm X12 Modified Lightweight Aluminium Front Housing X12 Aluminium Endcover with cooling fins Sensor Wire HighFlex 70mm Sensor Wire HighFlex 100mm Sensor Wire HighFlex 150mm Sensor Wire HighFlex 200mm 82505 Power Wire Set Brushless 2 6mm red black blue orange yellow 82506 Power Wire Set Brushless 3 3mm red black blue orange yellow 82510 Radical Motor Heatsink and Fan unique clamp style heatsink design 65790 Works Team Tools Motor Bearing Replacer expense according to our price list A proof of purchase including date of purchase needs to be included Otherwise no warranty can be granted For quick repair and return service add your address and detailed description of the malfunction If LRP no longer manufactures a returned defective product and we are unable to service it we shall provide you with a product that has at least the same value from one of the successor series The specifications like weight size and others should be seen as guide values Due to ongoing technical improvements which are done in the interest of the product LRP does not take any responsibility for the accuracy of these specs LRP Distributor Service e Package your product carefully and include sales receipt and detailed description of malfunction e Send parcel to your national LRP distributor e Distribut
8. w this product or other electronic components to come in contact with water oil or fuels or other electrocon ductive liquids as these could contain minerals which are harmful for electronic circuits If this happens stop the use of your product immediately and let it dry carefully Avoid overtightening the motor screws Damaged threads are not covered under warranty Avoid overloading the motor due to wrong or too long gear ratios Never apply full throttle if the motor is not installed Due to the extremely high RPMs without load the motor can get damaged Always wire up all the parts of the equipment carefully If any of the connections come loose as a result of vibration you could loose control over your model Avoid soldering longer then 5 seconds per soldering joint when replacing the power wires to prevent possible damage to the product due to overheating of the components Use a high power soldering station with at least 60W for soldering The manufacturer can not be held responsible for damages which are a result of non observance of the warning notes and security advices INSTALLATION amp CONNECTIONS HALL SENSOR WIRE This bi directional multipole wire which is supplied with all LRP sensored brushless speed controls connects the speedo and the motor Do not alter or modify this cable Make sure that the plugs have a proper and tight fit and are always clean POWER WIRES The unique splitted solder tabs allow easy and conv
9. wing neon Sanene Marking Timing coon x0 ooo x5 J o o E oo X Standard insert factory recommendation Ooo X Oo l w d E Comment Loosen the center endcover screw and remove screw and plastic endcover change to desired timing insert and rotate sen sor assembly slightly re attach endcover and tighten M2 screw care fully do not overtighten this screw Finished pa The crossed out wheeled bin means that within the European Union the product must be taken to seperate collection at the product end of life Do not dispose of these products as unsorted municipal waste REPAIR PROCEDURES LIMITED WARRANTY All products from LRP electronic GmbH hereinafter called LRP are manufactured according to the highest quality standards LRP gua rantees this product to be free from defects in materials or workmanship for 90 days non european countris only from the original date of purchase verified by sales receipt This limited warranty doesn t cover defects which are a result of misuse improper maintenance outside interference or mechanical damage This applies among other things on e Overload for example unsoldered Star ring e Excessive amounts of dirt inside the motor e Rotor damage due to debris inside motor e Mechanical damage due to external causes e Rust To eliminate all other possibilities or improper handling first check all other components in your model and the trouble shooting guide

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents