Home

UCAT-40

1. EEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e A WARNING This Product is for indoor use only Not for use in wet locations IMPORTANT INFORMATION e This product is a label unwinder It is only to be used to unwind labels of the recommended dimensions and weight in an indoor dry environment e The machine has to be unplugged before any manipulation The machine is to be used on a flat surface if the surface is not flat it is to be fixed using the holes in the base plate Do not leave the power cable in a passageway The ambient light of the working area needs to be sufficient to avoid any risk The unwinder can be used in ambient temperatures of 2 C to 40 C Connection of the machine to the power source must respect local and European legislations SET UP 1 Install the Control Arm referring to the enclosed TA User Manual 2 Mount the 400 mm 16 diameter Flange Plate onto the Quick Chuck Core Holder using the screws provided 3 Slide the Quick Chuck and Flange Assembly onto the UCAT 40 Motor Shaft allowing for clearance to the Chassis and Motor Screws Tighten the Allen screw to secure the Quick Chuck and Flange Assembly onto the Motor 4 Set the UCAT 40 in place near the label entrance path of the printer 5 CAUTION AVOID ACCIDENTS THE UCAT 40 WEIGHS APPROXIMATELY 13KG SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT 6 The UCAT 4O is bi directional It can rewind labels in e
2. MAINTENANCE Your UCAT 40 requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders meals Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cu
3. ither direction 7 Verify that the DIRECTION Switch on the UCAT 40 Control Panel is in the OFF position 8 Plug the Power Plug at the end of the wire on the AC Wall Transformer into the UCAT 40 Power Input Jack Plug the AC Transformer into an appropriate AC power outlet 9 The unit is now ready for use A FOR YOUR SAFETY Switch off device before any manipulation POWER UNWINDING 1 Place the DIRECTION Switch on the UCAT 40 Control Panel in the centre OFF position 2 Slide the roll of labels to be unwound on the Quick Chuck 3 Run the labels under the UCAT 40 Control Arm and into the printer 4 Place the DIRECTION switch in the desired position to feed the labels into your printer 5 Place the REWIND SLIT Switch in the Rewind position and advance the TORQUE Control about 1 3 rotation from fully Counter Clockwise as an initial setting 6 Start your printer and observe how the labels are being fed into the printer Adjust the TORQUE Control as needed to provide more or less unwind assistance As the printer uses the labels the Control Arm will rise causing the UCAT 40 to turn on and feed more labels As the UCAT 40 feeds more labels the labels and the Control Arm will drop down turning off the UCAT 40 until more labels are needed as the Control Arm is lifted again EXTERNAL HALT CONTROL An External Halt Control jack on the UCAT 3 is for use with external devices capable of providing an open ci
4. rcuit halt command A 3 5mm control cable is necessary for use not included With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using a 3 5mm dual circuit plug the UCAT 3 will operate When the External Circuit is opened the UCAT 3 will stop 3 5mm EXTERNAL HALT CONTROL Plug Dual Circuit Plug Contact CLOSED RUN _ Contact OPEN HALT Pin 1 No connection NOT USED Pin 2 Normally Closed NC contact Pin 3 Normally Closed NC contact return 12V me a 1K Dual Circuit ea E V
5. stomer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_UCAT 40 CE 01 13 Original user manual UCAT 40 Heavy Duty UCAT On Demand Powered Label Unwinder e Dual Torque Range and Direction Controls e Constant Adjustable Torque CAT technology e Adjustable Speed Control e Precise Variable Torque Control Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e UCAT 40 Drive Unit e Power Supply Module e LABELMATE Quick Chuck Quick Locking Core Chuck e Allen Wrench e Plastic Inner Flange Plate e Control Arm with setscrews and shaft screw Retain the Shipping Container and Packaging for Storage and Transport SPECIFICATIONS Weight of the machine 12 9Kg Max Label Roll Weight 14Kg Max Label Roll Diam 400mm Start Stop ON OFF ON Direction Switch Power Supply Input 220 240VAC 50 60Hz Output 11V AC e K

UCAT-40

Contents

Download Pdf Manuals

Related Search

Related Contents