USER`S MANUAL
Contents
1. Radio channel research 5 3 LED 1 FUNCTION RED Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK 5 4 STATE OF RX2 This function allows to visualize the state of the receiver of band 2 With MODE key Fig 28 find the text like in Fig 29 Reception OK Reception OK no DMX signal Radio channel research 5 5 LED 2 FUNCTION GREEN Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK 5 6 PAIRING WITH TRANSMITTER GET PAIRING This function allows to pair the Wi DMX set as receiver with a Wi DMX set as trasmitter to avoid interactions with other unit of the same type For this operation you need a DMX signal cable connected between the two unit Remove any cable on the DMX connectors and connect the DMX signal cable between the two unit On the RECEIVER Wi DMX with MODE key Fig 29 find the text like in Fig 30 On the TRANSMITTER Wi DMX with MODE key Fig 29 find the text like in Fig 31 On the RECEIVER Wi DMX hold SET key Fig 32 until a writing appears like in Fig 33 On the TRANSMITTER Wi DMX hold SET key Fig 32 until a writing appears like in Fig 34 RECEIVER Wi DMX TRANSMITTER Wi DMX PAIRING i PAIRING l Fig 33 Fig 34 I After a few seconds a result of the operation is given if like in Fig 35 on both u2. the value Fig 11 Use MODE key to move to the next value Fig 7 When finished confirm with SET key Fig 9 Fig 10 The range of DMX channels to transmit must correspond to the chan nels used by the projectors connected to the paired receivers on band 1 You should set such projectors on consecutive DMX addresses N B If you get problem of transmission try changing the Radio channel When Hadio channel is modified receivers start searching until they find the new Radio channel 4 3 LED 1 FUNCTION RED Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK 4 4 SETTING OF TX2 This function allows to set the range of DMX channels to transmit on band 2 GREEN LED to the paired receivers and the RADIO channel to use among the ten available from OG to 9G With MODE key Fig 12 find the text like in Fig 13 To change the setting hold SET key Fig 14 until the first value starts blinking Fig 15 Use UP DOWN keys to change the value Fig 16 Use MODE key to move to the next value Fig 12 When finished confirm with SET key Fig 14 The range of DMX channels to transmit must correspond to the chan nels used by the projectors connected to the paired receivers on band 2 You should set such projectors on consecutive DMX addresses N B If you get problem of transmission try changing the Radio channel When Hadio channel is modified receivers start s
3. Next pcro b Qe a ae Wireless DMX 512 TRANSCEIVER 3 USER S MANUAL We congratulate you on your purchase of Wi DMX Before you proceed using this product read this user s manual carefully as it gives important information on safety use and maintenance FRONT PANEL Shows the state of transmission receipt of the channel 1 Shows the state of transmission receipt of the channel 2 LCD display it shows all the informations on the Wi DMX functions MODE key SET key DOWN key UP key INDEX Setting of the equipment 1 1 Unpack WI DMX 1 2 Acessories and documentation provided with the equipment Description of the side panel and installation 2 1 Description of the side panel 2 2 Making a DMX 512 signal cable 2 3 Input connection for power supply 2 4 Connection of the ac adapter to main AC Initial setting 3 1 Setting of the operating mode Use of the equipment operating modes 4 1 TRANSMITTER mode 4 2 Setting of Tx1 4 3 LED 1 function 4 4 Setting of Tx2 4 5 LED 2 function 4 6 Receiver PAIRING 5 1 RECEIVER mode 5 2 State of Rx1 5 3 LED 1 function 5 4 State of Rx2 5 5 LED 2 function 5 6 Pairing with Transmitter GET PAIRING 5 7 Pairing with Transmitter GET PAIRING using Wi D PEN 6 1 EXTENDER mode 6 2 Setting of Tx1 6 3 LED 1 function 6 4 Setting of Rx2 6 5 LED 2 function 6 6 Receiver PAIRING 6 7 Pairing with Transmitter GET PAIRING 6 8 Pairing with Trans
4. O channel to use among the ten available from OR to 9H With MODE key Fig 46 find the text like in Fig 47 To change the setting hold SET key Fig 48 until the value starts blinking Fig 49 Use UP DOWN keys to change the value Fig 5C When finished confirm with SET key Fig 48 It is advisable not to use the same Radio channel found by the receiver N B If you get problem of transmission try changing the Radio channel When Hadio channel is modified receivers start searching until they find the new Radio channel 6 3 LED 1 FUNCTION Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK N B If a Radio channel between OR and 9H is used the led is Red If a Radio channel between OG and 9G is used the led is Green 6 4 SETTING OF RX2 This function allows to visualize the state of the receiver and to change the receiver band With MODE key Fig 51 find the text like in Fig 52 To change the receiver band hold SET key Fig 53 until the value changes Fig 54 Heception OK Reception OK no DMX signal Radio channel research Radio band changed 6 5 LED 2 FUNCTION Slow blinking Receiver OK no DMX 512 signal Fast blinking Channel research Switched on Receiver OK DMX 512 signal OK N B If a Radio channel between OR and QR is used the led is Red If a Radio channel between OG and 9G is used the led is Green 6 6 RECEIVER PAIRING T
5. ac adapter electric socket If the problem persist please consult your dealer 3 7 SETTING OF THE OPERATING MODE The Wi DMX factory default mode is TRANSMITTER REGARDLESS OF THE MODE YOU MUST EXECUTE THE PAIRING OPERATIONS EXPLAINED IN THE RELATIVE CHAPTERS OF THIS MANUAL This procedure allows to change between TRANSMITTER RECEIVER EXTENDER BACKUP mode of operation Power down the Wi DMX While holding down SET key Fig 2 Power up the Wi DMX On display appears as in Fig 3 Use UP DOWN keys to change operating mode Confirm with SET key Fig 2 4 1 TRANSMITTER MODE This operation mode allows you to transmit the DMX 512 signal coming from a con troller to the paired receivers through two channels of transmission The connection must be like in Fig 4 Wi DMX analyzes the DMX 512 signal as soon as the XLR connector is inserted and shows the number of channels generated from the controller Fig 5 in absence of signal the display appears like in Fig 6 DMX coming from controller DMX to other projectors Fig 4 4 2 SETTING OF TX1 This function allows to set the range of DMX channels to transmit on band 1 RED LED to the paired receivers and the RADIO channel to use among the ten available from OR to 9H With MODE key Fig 7 find the text like in Fig 8 To change the setting hold SET key Fig 9 until the first value starts blinking Fig o Use UP DOWN keys to change
6. ard DMX 512 signal OUTPUT with a 3 5 pole cannon connector Standard DMX 512 signal INPUT with a 3 5 pole cannon connector DMX TERMINATOR 2 2 MAKING A DMX 512 SIGNAL CABLE Wi DMX has a DMX 512 input output that uses standard XLR 5 pin or XLR 3 pin connectors The connection must be put into practice with shielded cable by these characteristics 2 conductors shield 120 Ohm impedance low capacity maximum transmission rate 250 Kbaud For the connection refer to the underlying picture XLR 3 pin Common ATTENTION the shield of the cable must never be connected to the ground of the electrical system as this could cause faults during the working of the Wi DMX 2 3 INPUT CONNECTION FOR POWER SUPPLY o g Plug the connector of the ac adapter completly in the power input To disconnect it extract gently ATTENTION do not use ac adapters different from the one supplied it could cause serious damages at the internal circuitation 2 4 CONNECTION OF THE AC ADAPTER TO THE MAIN AC MAKE SURE THAT VOLTAGE AND POWER FREQUENCY CORRESPOND TO WHAT IS REPORTED ON THE AC ADAPTER PLATE The supplied ac adapter has a plug therefore you should only plug it in the Socket When Wi DMX is powered on display appears as in Fig 1 if this condition is not Nort LIIREL rc c true please check if there is power in the electric socket or check the connection Fig 1 between ac adapter controller and
7. earching until they find the new Hadio channel 4 5 LED 2 FUNCTION GREEN Slow blinking Transmitter OK no DMX 512 signal Switched on Transmitter OK DMX 512 signal OK 4 6 RECEIVER PAIRING This function allows to pair the receiver Wi D Pen to the transmitter Wi DMX to avoid interactions with other unit of the same type With MODE key Fig 1 7 find the text like in Fig 18 Connect Wi D Pen to the DMX 512 transmitter signal IN Fig 20 1 without connecting Wi D Pen ac adapter Hold SET key Fig 19 until a writing appears like in Fig 2O PAIRING WATT ve Fig 20 Fig 20 1 After a few seconds a result of the operation is given if like in Fig 21 pairing succeeded else the message of Fig 22 appears PAIRING lt Fig 21 PAIRING 5 1 RECEIVER MODE This operation mode allows you to receive the DMX 512 signal coming from a Wi DMX transmitter and provide it to the connected projectors The connection must be like in Fig 23 In this mode switch terminator to ON Wi DMX receives the Radio signal and shows the number of channels generated Fig 24 in absence of Radio or DMX signal the display m appears like in Fig 25 DMX to other Terminator projector OMX nO DATI 5 2 STATE OF RX1 This function allows to visualize the state of the receiver of band 1 With MODE key Fig 26 find the text like in Fig 27 Heception OK Heception OK no DMX signal
8. his function allows to pair the receiver Wi D Pen to the TX1 of the Extender Wi DMX Follow the instructions at v par 4 6 6 7 PAIRING WITH TRANSMITTER GET PAIRING This function allows to pair the RX2 of the Extender Wi DMX with a Wi DMX set as trasmitter Follow the instructions at v par 5 6 6 8 PAIRING WITH TRANSMITTER GET PAIRING USING WI D PEN This function allows to pair the RX2 of the Extender Wi DMX with a Wi DMX set as trasmitter using Wi D PEN Follow the instructions at v par 5 7 7 1 TX BACKUP MODE TX BACKUP mode is intended for use as an immediate backup unit in case of failure during an event This mode works exactly the same as TRANSMITTER mode but data encoding is made using the key of another transmitter In the event of faiure of the original transmitter the unit set as TX BACKUP can generate the same signal as the original and then receiver will work without having to be paired again DO NOT operate the original transmitter and a backup unit togeter as they will inter fere each other How to set TX BACKUP mode Hemove power from Wi DMX unit Press and hold SET key fig 55 Power up Wi DMX then release SET On display appears as in fig 57 Use UP or DOWN key find TX BACKUP Press SET key to confirm How to clone a transmitter When in TX BACKUP mode Wi DMX can store up to 10 different configurations so it will be Fig 57 ready to backup one of 10 original transmit ters Before cloni
9. ld appear on display fig 63 Wi DMX TX BACKUP Wi DMX TRANSMITTER GR rr LEIER NAL Ww L R Fig 60 PAIRING PAIRING Fig 61 Fig 62 After a few seconds a result of the operation is given if like in Fig 63 on both units pairing suc ceeded else the message of Fig 64 appears After cloning the transmitter you can also set T 1 and T 2 DMX range and radio channel so the TX BACKUP will be ready for use If you want to clone another unit repeat from step 1 Each clone will keep the full setting DMX range and radio channel so when needed just select the clone and it will be working immediatly Wi DMX TECHNICAL FEATURES Technical features Signal Output signal DMX512 1990 Input signal DMX512 1990 Output connector 3 5 pin cannon connector female Input connector 3 5 pin cannon connector male Max number of projectors connected to the DMX output 32 Technical features Badio Frequency range 8 4 GHz 2 483 GHz ISM Number of channels 20 Transmitter range 1000 meters 3280 ft open air Climatic condition for the use Humidity 35 80 Temperature 5 50 C Power supply Voltage current 9 Vdc 800 mA Dimensions and weight Dimension W x L x H Weight 113 x 224 x 45 mm 0 9 Kg C 01220 C FCC ID REKUGWR2USXXXX Canadian Cert No IC 5125A UGWR2US CODEM MUSIC S r l Via G Pierini 13 61100 PESARO ITALY Tel 39 0721 204357 Fax 39 0721 203554 http w
10. mitter GET PAIRING using Wi D PEN 7 1 TX BACKUP mode 1 1 UNPACK WI DMX Open the box Remove the ac adapter and the documentation Take the equipment out of the box as shown in the picture below 1 2 ACESSORIES AND DOCUMENTATION PROVIDED WITH THE EQUIPMENT Verify the contents of the packing If one of the following parts of the packing is missing or damaged please contact your dealer immediately Wi DMX User s manual Warranty Ac adapter mod 1814807 1 XLR 3 5 P male connector e 1 XLR 3 5 P female connector Head the following warnings before beginning installation e This unit is not intended for home use e Head this manual thoroughly and observe the following precautions before working with the Wi DMX e Take care not to spill liquids on to the controller and do not use it in excessively humid conditions e Do not install Wi DMX near heat sources or expose it to direct sunlight and do not install in dusty environments without suitable protection e Do not use Wi DMX unless the ac adapter cable and plug are in perfect condition replace or repair if necessary e Do not use solvents such as acetone or alcohol to clean the controller or the finish and panel lettering will be damaged e f a fault occurs consult your nearest service centre or a specialized light equipment repair service Do not attempt to repair the controller yourself 2 1 DESCRIPTION OF THE SIDE PANEL 1 34 ex n lt Stand
11. ng a transmitter select where you want to save its data Using MODE key fig 56 find SELECT CLONE Ta on display fig 58 Press SET for more than 2 seconds Ta starts blinking Using UP or DOWN key select one of Ta to Tj available settings Press SET key to confirm Now you can clone your Wi DMX transmitter unit You can do that using the origi nal transmitter or using a Wi DPen receiver that has previously been paired with it With the original Wi DMX transmitter unit Remove any DMX cable from both Wi DMX the original TX and the BACKUP Connect a DMX cable between the two units Wi DMX TRANSMITTER using MODE key find PAIR RECEIVER on display fig 6O don t press SET yet On Wi DMX TX BACKUP using MODE key find CLONE PAIRING on display then press SET for more than 2 seconds PAIRING READING appears fig 61 Wi DMX TRANSMITTER press SET for more than 2 seconds PAIRING WAIT appears fig 62 After a few seconds a result of the operation is given if like in Fig 63 on both units pairing suc ceeded else the message of Fig 64 appears With a Wi DPen receiver this way you can clone a TX even AFTER it is dead Remove any DMX cable from Wi DMX set as TX BACKUP Connect Wi DPen to DMX IN plug of Wi DMX Wi DMX TX BACKUP using MODE key fig 56 find CLONE PAIRING on display then press SET for more than 2 seconds PAIRING READING appears fig 61 After a few seconds PAIRING OK shou
12. nit pai ring succeeded else the message of Fig 36 appears PAIRING lt Fig 35 PAIRING FAILED Fig 36 5 7 PAIRING WITH TRANSMITTER GET PAIRING USING WI D PEN This function allows to pair the Wi DMX set as receiver with a Wi DMX set as trasmitter For this operation you need a Wi D PEN already paired with the trasmitter Wi DMX v par 4 6 With MODE key Fig 37 find the text like in Fig 38 Connect Wi D Pen to the DMX signal input without connecting Wi D Pen ac adapter Hold SET key Fig 39 until a writing appears like in Fig 4 HIRING Fig 38 PAIRING READING Fig 40 After a few seconds a result of the operation is given if like in Fig 41 pairing succeeded else the message of Fig 42 appears PAIRING Fig 41 PAIRING FAILED Fig 42 6 1 EXTENDER MODE This operation mode allows you to receive the DMX 512 signal coming from a Wi DMX transmitter provide it to the connected projectors and re transmit it to other receiver unit The connection must be like in Fig 43 In this mode switch terminator to ON Wi DMX receives the Radio signal and shows the number of channels generated Fig 44 in absence of Radio or DMX signal the display m appears like in Fig 45 J DMX to other Terminator projector 6 2 SETTING OF TX1 This function allows to set the range of DMX channels to transmit on band 1 RED LED to the paired receivers and the RADI
13. ww wi dmx com E mail info codemmusic com 7 3 All rights reserved No parts of this document can be copied photocopied or reproduced without the prior written permission of the CODEM MUSIC s r l No responibility is taken for possible inaccuracies or mistakes The CODEM MUSIC s r l reserves the right to make any alterations or aesthetics changes of this product that seem necessary at any time and for whatever reason The CODEM MUSIC s r l takes no responsibility for the use or for the application of this product
Download Pdf Manuals
Related Search