Manual - Legend Power Systems
Contents
1. One Delivery AFN FV One Call gt One Day gt One Delivery is resistive or shorted defective ePress SELECT button momentarily AGAIN selects Capacitance function Capacitance measurement time varies with capacitance value Only a few seconds is required for measuring values of below 100uF However one minute or more is required for measuring extreme values of around 2000uF HOLD feature The Hold feature freezes the display for later viewing Press the HOLD button momentarily to toggle to the Hold feature The annunciator turns on Backlighted display model 118 only Press the SELECT button for 1 second or more to turn on or off the display backlight feature Auto Power Off APO The meter turns off intelligently after approximately 3 minutes of neither significant measurement nor button switch activity To wake up the meter from APO press any button or turn the rotary selector to OFF and back on again Always turn the rotary selector to OFF when the meter is not in use 5 MAINTENANCE WARNING To avoid electrical shock disconnect the meter from any circuit remove the test leads from the input jacks and turn OFF the meter before opening the case Do not operate with open case Trouble Shooting lf the instrument fails to operate check batteries and test leads etc and replace as necessary Double check operating procedure as described in this user s manual If the instrument voltage resistance input t2. AC 600V range has the lowest sensitivity Measuring the signal in ACV function WHILE selecting Line Level Hz function in that ACV range automatically sets the most appropriate sensitivity for higher voltage applications This can avoid electrical noises as in 110 220V line voltage applications for example If the reading shows zero due to insufficient signal levels select Line Level Hz function BEFORE making measurements at AC 6V range will set the highest sensitivity Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery A ZN FV One Call gt One Day gt One Delivery AutoCheck mode Set the slide switch function selector to the te position This innovative AutoCheck feature automatically selects measurement function of DCV ACV or Resistance Q based on the input via the test leads eWith no input the meter displays Auto when it is ready eWith no voltage signal but a resistance below 6MQ is present the meter displays the resistance value When below 2502 0 025kQ2 is present the meter further gives a continuity beep tone eWhen a signal above the threshold of 1 5 VDC 1 VDC or 2 VAC up to the rated 600V is present the meter displays the voltage value in appropriate DC or AC whichever larger i
3. ePress the jaw trigger and clamp the jaws around only one single conductor of a circuit for load current measurement Make sure the jaws are completely closed or else it will introduce measurement errors Enclosing more than one conductor of a circuit will result in differential current like identifying leakage current measurement e Adjacent current carrying devices such as transformers motors and conductor wires will affect measurement accuracy Keep the jaws away from them as much as possible to minimize influence Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery Hi Z DCV ACV amp Line Level Hz functions Set the slide switch function selector to the zY position selects common impedance Hi Z voltage measurements Input impedance is set at approximately 5MQ to minimize loading on circuits under tests DCV is the default function The DC annunciator turns on Press SELECT button momentarily to select ACV The AC annunciator v turns on Press momentarily again to activate the Line Level Hz function Note eLine Level Hz input sensitivity varies automatically with ACV range selected when Line Level Hz is selected AC 6V range has the highest and
4. readings It is an invaluable feature for precise indication of hard signals such as distinguishing between hot and open wires to ground in electrical installation applications WARNING eAutoCheck mode input impedance increases abruptly from initial 1 6kQ to a few hundred kQ s on high voltage hard signals LoZ displays on the LCD to remind the users of being in such low impedance mode Peak initial load current while probing directly to 600VAC for example can be up to 530mA 600V x 1 414 1 6kQ decreasing abruptly to approx 4mA 600V x 1 414 210kQ within a fraction of a second Do not use AutoCheck mode on circuits that could be damaged by such low input impedance Instead use slide switch function selector common input impedance voltage modes Hi Z of approx 5MQ to minimize loading for such circuits Manual or Auto ranging When the function selected has more than one range press the RANGE button momentarily selects manual ranging The meter remains in the range it was in The LCD annunciator turns off Press the button momentarily again to step through the ranges Press and hold the button for 1 second or more to resume auto ranging Note Manual ranging feature is not available to 600Q2 F A functions To use Manual ranging feature in AutoCheck mode please see Range Lock Feature as explained in footnotes of AutoCheck mode section Customer Care Australia P 13122 F 1300 303 310 E s
5. 47 2 COCA BA C Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery LIMITED WARRANTY BRYMEN warrants to the original product purchaser that each product it manufactures will be free from defects in material and workmanship under normal use and service within a period of one year from the date of purchase BRYMEN s warranty does not apply to accessories fuses fusible resistors spark gaps batteries or any product which in BRYMEN s opinion has been misused altered neglected or damaged by accident or abnormal conditions of operation or handling To obtain warranty service contact your nearest BRYMEN authorized agent or send the product with proof of purchase and description of the difficulty postage and insurance prepaid to BRYMEN TECHNOLOGY CORPORATION BRYMEN assumes no risk for damage in transit BRYMEN will at its option repair or replace the defective product free of charge However if BRYMEN determines that the failure was caused by misused altered neglected or damaged by accident or abnormal conditions of operation or handling you will be billed for the repair THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE BRYMEN WILL NOT BE LIABLE F
6. AFN FV One Call gt One Day gt One Delivery USER S MANUAL BM117 BM118 Auto Check Clamp on Multimeter Series MAX 2000A 600V CAT I L A HOLD HI C EF NCV True RMS C 118 AutoCheck Clamp D0 empr a a a E Maaja ILI MVMKAQH SELECT RANGE BRYMEN BRIGHT PEOPLE S CHOICE Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 TCA BAG One Call gt One Day gt One Delivery Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz AFN FV One Call gt One Day gt One Delivery 1 SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and maintaining the instrument in a safe operating condition If the instrument is used in a manner not specified by the manufacturer the protection provided by the instrument may be impaired The meter meets the requirements for double insulation to IEC61010 2 032 1994 EN61010 2 032 1995 UL3111 2 032 1999 Category III 600 Volts ac and dc PER IEC61010 OVERVOLTAGE INSTALLATION CATEGORY OVERVOLTAGE CATEGORY II Equipment of OVERVOLTAGE CATEGORY II is energy consuming equipment to be supplied from the fixed installation Note Examples include household office and laboratory appliances OVERVOLTAGE CATEGORY III Equipment of OVERVOLTAGE CATEG
7. OR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES BRYMEN BRIGHT PEOPLE S CHOICE BRYMEN TECHNOLOGY CORPORATION TEL 886 2 2226 3396 FAX 886 2 2225 0025 http www brymen com EO PRINTED ON RECYCLABLE PAPER PLEASE RECYCLE COPYRIGHT MMIV Btc ALL RIGHTS RESERVED P N 7M1C 0571 0000 PRINTED IN TAIWAN Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 TCA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery 12
8. ORY III is equipment in fixed installations Note Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation OVERVOLTAGE CATEGORY IV Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation Note Examples include electricity meters and primary over current protection equipment TERMS IN THIS MANUAL WARNING identifies conditions and actions that could result in serious injury or even death to the user CAUTION identifies conditions and actions that could cause damage or malfunction in the instrument Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 COCA BA C Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery WARNING To reduce the risk of fire or electric shock do not expose this product to rain or moisture The meter is intended only for indoor use To avoid electrical shock hazard observe the proper safety precautions when working with voltages above 60 VDC or 30 VAC rms These voltage levels pose a potential shock hazard to the user Inspect test leads connectors and probes for damaged insulation or exposed metal before using the instrument If any defects are found replace them immediately Do no
9. ales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 TCA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery A ZN FV One Call gt One Day gt One Delivery MAX 2000 600V CAT m HOLD C EF NCV True RMS C MAX 2000A 600V CAT IIL L a MAX COM 600v caru L A Electric Field EF Detection At any function press the EF NCV button momentarily to toggle to EF Detection feature The meter displays tr when it is ready Signal strength is indicated as a series of bar graph segments on the display plus variable beep tones eNon Contact EF Detection NCV An antenna is located along the top of the Stationary jaw See symbol on the jaw which detects electric field surrounds current carrying conductors It is ideal for tracing live wiring connections locating wiring breakage and to distinguish between live or earth connections eProbe Contact EF Detection For more precise indication of live wires such as distinguishing between live and ground connections use the Red test probe for direct contact measurements Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Deliv
10. erminal has subjected to high voltage transient caused by lightning or switching surge to the system by accident or abnormal conditions of operation the series fusible resistors will be blown off become high impedance like fuses to protect the user and the instrument Most measuring functions through this terminal will then be open circuit The series fusible resistors and the spark gaps should then be replaced by qualified technician Refer to the LIMITED WARRANTY section for obtaining warranty or repairing service Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery Cleaning and Storage Periodically wipe the case with a damp cloth and mild detergent do not use abrasives or solvents If the meter is not to be used for periods of longer than 60 days remove the batteries and store them separately Battery replacement The meter uses standard 1 5V AAA Size NEDA 24A or IEC LRO3 battery X 2 Loosen the 2 captive screws from the battery cover case Lift the battery cover case Replace the batteries Replace battery cover case Re fasten the screws Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 21
11. ery AFN FV One Call gt One Day gt One Delivery 6000 4 functions Set the slide switch function selector to the 6000 F F position 60002 Resistance range with Audible Continuity is the default function It is an extended low resistance range to complement the Resistance Q function in AutoCheck mode Audible Continuity response time is also improved drastically from that of AutoCheck mode under such stand alone range architecture Audible Continuity is convenient for checking wiring connections and operation of switches A continuous beep tone indicates a complete circuit ePress SELECT button momentarily selects Diode test function The reading shows the approximate voltage drop across the test leads When forward biased normal forward voltage drop for a good silicon diode is between 0 400V to 0 900V A reading higher than that indicates a leaky diode defective A zero reading indicates a shorted diode defective and the meter gives a continuous beep warning An OL indicates an open diode defective Reverse the test leads connections reverse biased across the diode The display shows OL if the diode is good Any other readings indicate the diode Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 TCA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt
12. n peak magnitude eOverload Alert Feature When above rated 600V is present the meter displays OL with a warning beep tone for over range indication Disconnect the test leads from the signal immediately to avoid hazards Note eRange Lock Feature When a measurement reading is being displayed in Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery AutoCheck mode press the RANGE button momentarily 1 time can lock the function range it was in The LCD annunciator NUyke turns off Range lock can speed up repetitive measurements Press the button momentarily repeatedly to step through the ranges Press and hold the button for 1 second or more to resume AutoCheck mode eAs Hazardous Alert When making resistance measurements in AutoCheck mode an unexpected display of voltage readings alerts you that the object under test is being energized eGhost voltage buster Ghost voltages are unwanted stray signals coupled from adjacent hard signals which confuse common multimeter voltage measurements Our AutoCheck mode provides low ramp up input impedance approx 1 6kQ at low voltage to drain ghost voltages leaving mainly hard signal values on meter
13. on Contact EF Detection NCV T 118F01 4 antenna position 2 Jaw marking lines for ACA position error indication 3 Hand Finger Barrier to indicate the limits of safe access to the jaws during 10 Current measurements 10 4 Push buttons for special functions amp features 5 Input Jack for all functions EXCEPT non invasive ACA current function 9 MAX 2000A 6 Common Ground reference Input a 4 Jack for all functions EXCEPT HOLD non invasive ACA current function True RMS Oo 7 Slide switch Selector to turn the power ON OFF and Select a function m fy Fee Fn a Ja pa 8 3 5 6 digits 6000 counts LCD 1 IILI aapa LD kA 4 9 Jaw trigger for opening the transformer clamp jaws y 10 Jaw center Indicators at where c ev car best ACA accuracy is specified O O 6 11 Transformer Clamp Jaws for AC current magnetic field pick up Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery AFN FV One Call gt One Day gt One Delivery 4 OPERATION MAX 2000A 600V CAT my HOLD True RMS ACA Current clamp on function set the slide switch function selector to the A position Inputs are made through the clamp jaws for non invasive ACA current measurements CAUTION
14. t touch test lead tips or the circuit being tested while power is applied to the circuit being measured To avoid accidentally short circuit of bare uninsulated hazardous live conductors or busbars switch them off before insertion and removal of the current clamp jaws Contact with the conductor could result in electric shock Keep your hands fingers behind the hand finger barriers that indicate the limits of safe access of the meter and the test leads during measurement CAUTION Disconnect the test leads from the test points before changing meter functions INTERNATIONAL ELECTRICAL SYMBOLS Caution Refer to the explanation in this Manual Caution Risk of electric shock Earth Ground Double Insulation or Reinforced insulation Fuse AC Alternating Current DC Direct Current i oe e 2 CENELEC Directives The instruments conform to CENELEC Low voltage directive 73 23 EEC and Electromagnetic compatibility directive 89 336 EEC Customer Care Australia P 13122 F 1300 303 310 E sales cabac com au W cabac com au A Distribution PI Seven Hills NSW 2147 2 CA BAG Customer Care New Zealand P 0800 966 969 F 0088 6969 E sales cabac co nz W cabac co nz One Call gt One Day gt One Delivery A ZN FV One Call gt One Day gt One Delivery 3 PRODUCT DESCRIPTION This user s manual uses only representative model s for illustrations Please refer specification details for function availability to each model 1 N
Download Pdf Manuals
Related Search