Home

Speco D8HS, D16HS

1. DISK INFO Hard drive information Displays the following information ENE EE MODEL NAME ibid GOOD NOR AL BAD ST3500411SV 40 C 104 F GOOD OK DETAIL Reallocated Current Pending Uncorrectable Spin Retry RECORDING Enable disable recording limit LIMIT RECORDING Set the recording limit days 1 90 days LIMIT DAYS If the RECORDING LIMIT DAYS are set to 1 the data will be overwritten after 24 hours 49 4 9 Setup CONFIG Mode In the SETUP menu select the CONFIG tab Then the configuration menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control O 799999 O 0 0 Ed n e Y CONFIG EXPORT TO USB IMPORT FROM USB AN LOAD DEFAULT a LOAD FACTORY DEFAULT AN SOFTWARE UPGRADE TEEN APPLY CANCEL Figure 4 9 1 CONFIGURATION Setup Screen Table 4 9 1 CONFIGURATION Setup Item Description EXPORT TO User can save the current configuration Setting values of the DVR to the USB USB flash drive Plug in the USB flash on the front panel and press the button to start the saving process IMPORT FROM User can upload the configuration of the DVR to another DVR using the USB USB Flash drive Plug in the USB flash drive on the front panel and press the button to start the loading process LOAD DEFAULT Press the button to reset the system to the default settings The following
2. EJE e ooo So Figure 4 1 2 IP CAMERA Setup Screen 192 168 0 79 Camera Scanning has been completed REFRESH PROFILE NAME RESOLUTION FRAME RATE Profiled 1920 A 1080 30 640 X 360 30 Profile Scanning has been completed REGISTER CANCEL IP 192 168 0 79 Camera Scanning has been completed REFRESH REGISTER CANCEL Main APPLY CANCEL Figure 4 1 4 ONVIF Protocol Profile SCAN Image S50060 proper operation and updated using the ONVIF setup menu ONVIF Setup Menu may not be accessible depending on the ONVIF version used by the IP camera 4 1 2 ONVIF SETUP Menu VIDEO NETWORK SYSTEM After registering the basic information is displayed Select the protocol used by the IP Camera and then click the scan button Select the IP Camera from the list and then click the register button IP cameras using ONVIF protocol require ID Password and Profile to be correctly entered for SPECO protocols only require ID and Password to be correctly entered for proper operation IP cameras using ONVIF protocol can have their Video Network and System settings accessed Table 4 1 2 Menu Items in ONVIF Setup Screen Menu Item Description VIDEO Video Encoder to view and change to audio settings 21 VIDEO RESOLUTION 1920 X 1080 FRAMERATE 30 BITRATE Kbps 2500 ENCODER IFRAME INTERVAL 30 H 264 PROFILE Main AUDIO CODEC SUPPORTS ONLY G 711
3. 17 2 4 3 EZ NETWORK setting Not using internet connection 172 16 2 62 255 255 0 0 172 16 1 254 168 126 63 1 168 126 63 2 3 3 3 3 a frist BANGED Figure 2 4 3 EZ NETWORK Setup Manual Configuration Screen Select NO if the HS is not using an internet connection Select Auto Configuration DHCP or Manual Configuration STATIC and then click TEST button when ready Input the Network Settings if Manual Configuration STATIC was selected and click TEST Select OFF for ENABLE DDNS and click NEXT button Click Finish to save the setup YO w amp 18 2 4 4 EZ Record setting i lt lt PREV NEXT D gt caNCEL Figure 4 2 4 EZ RECORD Setup Procedure Select EZ Record for Date Time and Record Setup Click NEXT to proceed Description of EZ Record Setup is displayed Click NEXT to proceed Set up the Date Time settings and click NEXT to get to the record setup Select Recording mode setup for Continuous Motion and Setup click NEXT button OOWwWHO Select Record video quality setup for Resolution and Setup click NEXT button 19 2 5 IP Camera SETUP through SpecoTech Web Viewer HS Series allows remote access to the IP Cameras through IP Camera Setup menu in SpecoTech Web Viewer 2013 11 1
4. APPLY CANCEL NETWORK View and change Network settings NETWORK INTERFACE NAME f4fca9d5 b223 45d4 9bd8 43c62e12 INTERFACE TYPE STATIC IP 172 16 2 81 _ SUBNET MASK 255 25500 n n GATEWAY 172 16 1 254 RTSP PORT Ea WEB PORT EN HTTPS 0 APPLY CANCEL SYSTEM System information and change your password factory reset and the camera is rebooting SYSTEM DEVICE INFORMATION el z ee USER PASSWORD admin I FACTORY DEFAULT e MANUFACTURER Probe MODEL PIN H2000A CAMERA REBOOT 4 FIRMWARE VERSION 1 00 04 SERIAL NUMBER 2000beff21 HARDWARE ID PIN H2000A APPLY CANCEL 28 4 1 3 SCAN Menu PORT WEB PORT 192 168 78 11 554 T P m T KA Figure 4 1 2 IP CAMERA Setup Screen Figure 4 1 3 Search IP Camera Screen Select the IP Camera protocoland then on click the scan button Select the ip camera on the list and then click the register button 3 After the registration is completed the basic information is to be displayed 4 2 Setup SYSTEM In the SETUP menu select the SYSTEM tab Then the SYSTEM menu is displayed as pictured below Navigate through the menu items using the mouse or the remote control and change the value of the menu i T eet e A ke T f i Ye E i F i y E9 m e Figure 4 2 1 SYSTEM Setup Screen 29 Table 4 2 1 Menu Items in SYSTEM Setup Screen Item Description DESCRIPTION Press the
5. Indicates the DVR is locked Note to unlock right click on the live view screen and click on Unlock Indicates audio is muted on all channels Indicates that alarm is set To set the alarm function press the Alarm button on the front panel CoN Indicates that alarm output is activated Event indicator When there is an event motion recording video loss HDD fail S M A R T this icon will be highlighted Indicates that a network client is connected to the DVR Op B Indicates that sequencing mode is enabled 05 29 2013 15 42 10 Displays the current date and time 52 Remote control ID display If a remote ID is not set the message ALL is displayed Displays the amount of recording on the hard disk from 0 99 Indicates that HDD is recycled Continuous recording in progress Manual recording in progress To set the Manual recording mode press the Record button on the front panel Motion alarm recording in progress 5 Sensor recording in progress Right click the mouse and the quick operation window will be displayed as below SUPER EZ COPY ENABLE MANUAL RECORD INSTANT PLAYBACK ADVANCED MENU EZ SETUP AUDIO MUTE CAMERA PTZ ENABLE MAIN MONITOR SEQUENCE DISABLE ALARM OUT MANUAL DIGITAL DETERRENT SITE INFORMATION SYSTEM INFORMATION EXPORT HELP SYSTEM LOCK SYSTEM SHUTDOWN Figure 5 1 2 Quick Operation Window Ta
6. Put the cursor of the mouse on the channel which is connected to the site and right click on the mouse to open the submenu Then the following window is displayed as below Select the REMOTE SETUP Se A REN EX speco technologies Be e ng D16HS IP 172 16 2 57 SPECO Multi Client SPECO Multi Client Ver 3 1 3 8 Ver 3 1 3 8 Disconnect High Quality Normal Quality z IFrame Only High Quality d a AR Normal Quality IFrame Only Full Screen SPECO Multi Client SPECO Multi Client SE Aspect Ratio Ver 3 1 3 8 Ver 3 1 3 8 setup Exit Remote Setup Camera Setup Lock EN r SS Site Information SPECO Multi Client SPECO Multi Client SPECO Multi Client Ver 3 1 3 8 Ver 3 1 3 8 Ver 3 1 3 8 l Full Screen Aspect Ratio Then the setup window is displayed The specified menu screen is displayed on the upper left of the screen Enter the password of the DVR when prompted NOTE The default password is 1111 Setting is the same as with the DVR menu setting Refer to the corresponding pages for details on the setting items 17 SPECO WEB SETUP GC D 172 16 2 62 cgi bin websetup cg SPECO WEB SETUP PASSWORD LoGIM NOTICE Web Setup is prohibited when DVR is in local Setup Menu SPECO WEB SETUP Ce D 172 16 2 62 cgi bin websetup cg SPECO WEB SETUP PASSWORD LOGIN THE SYSTEM IS NOT IN THE LIVE MODE REMOTE SETUP IS PROHIBITED AT THIS TIME 7 7 1 IP Camera Select IP Ca
7. speco technologies User s Guide ver 1 0 Models D8HS D16HS 8 16 Channel IP amp Analog 960H Hybrid DVR About This User s Guide Before operating the unit please read this user s guide thoroughly and retain it for future reference Cautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of Graphical Symbols This symbol indicates the presence of important operating and maintenance servicing instructions in the literature accompanying the product This symbol indicates the presence of dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock property damage personal injury or death WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture CAUTION Changes or modifications not approved by the manufacture will void the warranty of the product Using an incompatible battery may increase the risk of fire or explosion Replace only with the same or equivalent type battery recommended by the manufacture Discard used batteries according to manufacturer s instructions These precautions MUST be followed for safety reasons Warning e Do not use if the unit emits smoke e Do not disassemble the unit e Do not place a
8. Figure 5 3 1 5 Play Mode Screen 1 When the EZSearch menu is selected the user can see a calendar which displays recorded dates with highlights Select a specific date on a calendar Select a channel from Channel Selection Screen Then 24 Hourly Thumbnail Search screen displays Select the hourly thumbnail Then Minute Thumbnail Search screen displays Select the thumbnail of seconds amp minutes that you want to playback 57 5 3 2 Time Line Search The CALENDAR Search window is used to find the stored video by using the time line bar Jan 2014 17 24 lt PREV NEXT gt CLOSE Figure 5 3 2 1 Calendar Screen 01 10 2014 00 00 00 0 3 6 9 12 15 vititizitizitizi ike ake lke alk mike aie ale alte mike OONOUPLWNE Channel ALL CH1 CH2 CH3 CH4 CH5 CH6 CH7 CHS8 CH 9 CH 10 CH 11 CH 12 CH 13 CH 14 CH 15 CH 16 lt PREV CLOSE Figure 5 3 2 2 Time Line Search Screen PLAY When the Timeline menu is selected the user can see a calendar which displays recorded dates with highlights Select a specific date and time Click and drag the red time indicator bar to the desired hour User can select a specific minutes using a button in the above red box Press the PLAY button after selecting the specific time Press the PREV to return to the SEARCH window 5 3 3 Event Search The Event Search window is used to find stored video CHANNEL 45 CH6 CH7 CH8 CH9 CH
9. Mo o j2 1 j2 j2 2 2 jaja 3 la a ja o Js js je je je 7 7 E COPY SCHEDULE _ 1 CH 1 O CH 2 OG CH 5 CH 6 CH 9 C CH 10 O CH 13 CH 14 38 4 4 2 Keyboard Controller amp PTZ Setup To control the PTZ functions of the camera connect the PTZ controller to the RS 485 port on the back of the chassis with CAT5 or equivalent cable D Connect the RS 485 cables of PTZ camera to the RS 485 port on the rear panel i Sensor Inputs Alarm Output Figure 4 4 2 1 Device Mode Setup Screen 2 Open the PTZ sub menu by selecting the submenu button CONTROLLER SPEED ID CHANNEL CAMERA SPEED ID i Figure 4 4 2 2 PTZ Control Setup Screen Note Connect PTZ cameras that support RS 485 directly to the RS 485 port If the camera is controlled through an RS 232C interface use an RS 232C to RS 485 to RS 232C signal converter Use the PTZ setup screen to select the following options for the camera PTZ controller CHANNEL Channel connected to a PTZ device CAMERA Protocol Type SPEED 19200 14400 9600 4800 2400 Baud rate ID 0 63 Controller Keyboard Controller If a PTZ controller is used select a controller protocol from Controller menu Set SPEED Baud Rate and ID number 39 CONTROLLER SPEED ID VC PROTOCOL CHANNEL CAMERA SPEED ID WTX 1200A Figure 4 4 2 3 Controller Selection Screen 4 4 3 Spot Out SPOT ON EVENT SPOT EVENT DWELL TIME SE
10. Table 4 1 1 Menu items in IP CAMERA mode setup Item Description CHANNEL E To manually connect each camera click on the to get this window 3 PROTOCOL IP PORT WEB PORT OTHERS s SPECO Y 172 16 2 66 HO 10 0 0 0 0 B0 ONVIF 11 SPECU 0 0 0 0 80 12 SPECO 0 0 0 0 ao 13 SPECO 0 0 0 0 55 ao 14 SPECO 0 0 0 0 ao 15 SPECO 0 0 0 0 i go 16 SPECO 0 0 0 0 B0 Under the column labeled Type Select IP Camera Protocol PROTOCOL Double Click to Scan 10 SPECO ONVIF 11 SPECU 25 SCAN Double click the empty box to search IP camera on the local network CON A 192 168 78 11 994 Camera Scanning has been completed IP Enter the address of IP camera to connect or select from scanned list PORT Enter the port number of IP camera to connect WEB PORT Enter the web port number of IP camera to connect OTHERS Change the IP camera setting Double click the empty box and then Log In box will be pop up Enter ID and PASSWORD of IP Camera ID PASSWORD PROTOCOL Select the protocol for the IP Camera SCAN Searches the network for IP Cameras using the specified protocol IP Enter the IP Address of the desired IP Camera PORT Enter the IP Camera stream Port Number default 554 WEB PORT Enter the IP Camera Web Port Number default 80 OTHERS IP Camera Video Setup Resolution Frame rate and Bitrate 4 1 1 SCAN Menu Scan for IP Cameras on network using ONVIF SPECO protocols
11. name and select OK using the mouse The name can be made up to 36 characters COVERT Enable disable display of the specified video channel in live display COLOR TUNING BRIGHTNESS CONTRAST HUE SATURATION Brightness Change the brightness value 0 100 Contrast Change the contrast value 0 100 Hue Change the hue value 0 100 Saturation Change the saturation value 0 100 VIDEO OUTPUT Select 1280x720 or 1920x1080 4 6 Setup NETWORK Mode Select the NETWORK tab Then the network menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control TEE E Je T T Figure 4 6 NETWORK Setup Screen 43 Table 4 6 Menu Items in NETWORK Setup Screen Item Description NETWORK TYPE DHCP DVR will automatically retrieve an IP address STATIC Network information must be manually configured IP Enter IP address that is assigned for the DVR SUBNET MASK Enter Subnet Mask that is assigned for the DVR GATEWAY Enter Gateway that is assigned for the DVR DNS PRIMARY Enter Primary DNS address that is assigned for the DVR DNS SECONDARY Enter Secondary DNS address assigned for the DVR DDNS Dynamic Domain Name System DDNS allows a DNS name to be constantly synchronized with a dynamic IP address In other words it allows using a dynamic IP address to be associated with a static domain name so others
12. 5 Go To Last Time You can access from the last minute recorded data on the DVR hard drive by selecting GO TO LAST TME on the SEARCH window Press the PREV to return to the SEARCH window 5 3 6 Go To Specific Time User can search for video data from a specific instance by setting the date and time in the GO TO SPECIFIC TIME menu Use the mouse or the remote control to change the date and time value and press the PLAY button after setting If there is no video data in the set date and time No Data Exist message displays 5 3 7 Archive List The ARCHIVE Search window is used to find previously stored video or images oe ATE PLAY BMP SPLIT 41 15 2013 13 45 49 11 15 2013 13 55 44 2 log s found lt PREV DISPLAY CLOSE Figure 5 3 7 Archive Search Screen When the Archive menu is selected the user can see a calendar which has recording data Select a specific date and then the archived data will be displayed Press the Display button to view the still image or the first frame of the selected video then the user can save the selected data 59 5 3 8 Log List You can access the LOG list search screen by selecting LOG on the SEARCH window Setup Exit Setup Exit 06 23 2014 00 13 14 Network ADMIN Connect from 172 16 5 220 06 23 2014 00 13 57 Network ADMIN Disconnect from 172 16 5 220 06 23 2014 00 14 01 5 log s found BACKUP CLOSE Figure 5 3 8 Log List Screen When the Log menu is selected the user c
13. Codec G 711 G 711 Sensor Local 27 4 Remote eal comes rima a is ooo o o IP Resolution B 1920x1080 240 200fps 480 400fps B Rate Co o IET Recording Mode Continuous Motion Sensor Continuous Motion Sensor Schedule Manual Continuous Schedule Manual Continuous Sensor Continuous Motion Sensor Continuous Motion Pre Recording Max 20 Minutes Max 20 Minutes Post Recording Max 60 Seconds Max 60 Seconds Playback Search Quick Search Date Time Quick Search Date Time Event Archive Log Event Archive Log Playback Speed x0 25 x0 5 x2 x4 x8 x16 x0 25 x0 5 x2 x4 x8 x16 X32 x64 X32 x64 Backup Meda o USB drive External HDD USB drive External HDD File Format BMP AVI Proprietary Format BMP AVI Proprietary Format Huge Backup Yes Max 24 hours Yes Max 24 hours Storage HDD Capacity of 1 3TB 3 1 2 1 U HD Internal HDDs sara A ar A User I F Input Method Front Buttons IR Mouse Front Buttons IR Mouse Mud Network Interface 10 100 1000 Base T 10 100 1000 Base T rev James ome S M A R T e S es S e Network Mobile viewer Speco Player Live Search Speco Player Live Search Access PTZ 2 Way Audio PTZ 2 Way Audio PC Web Viewer Windows Windows IE Chrome Firefox Safari IE Chrome Firefox Safari PC Client SecureGuard CMS and secureGuard CMS and SpecoTech Multi Client Viewer Power Supply Voltage 12V 5A Temperature Operat
14. INFORMATION OVERWRITE O ON 0 OFF DISK INFO HDD SIZE 435 GB FREE 42 GB HDD LAST TIME 01 10 2014 20 51 00 HDD 2 MODEL NAME ST3500411SV TEMPERATURE 41 Celsius 105 Fahrenheit HEALTH GOOD NORMAL BAD GOOD REALLOCATED SECTORS CURRENT PENDING SECTORS UNCORRECTABLE SECTORS SPIN RETRY SECTORS RECORDING LIMIT OFF v RECORDING UIMIT DAYS 30 DAY S e OVERWRITE Select on to continue recording by overwriting when the hard disk becomes full e DISKINFO Hard drive information e RECORD LIMIT Sets whether to limit or not the recording data storage period 7 7 9 Remote Upgrade IP CAMERA SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE INFORMATION Model Name DIHS Current Software Ver 4 1 0 20740611 UPGRADE RELOAD apro Shows the current Firmware version installed on DVR o Browse Select BROWSE to locate the firmware file eo Upgrade Select UPGRADE to upgrade the firmware of the DVR 7 7 10 Information SPECO WEB SETUP ses IP CAMERA SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE MODEL NAME D16HS SOFTWARE VERSION Ver 3 9 3 20131206 STORAGE SIZE 435 GB NETWORK TYPE DHCP IP ADDRESS 172 16 2 41 MAC ADDRESS 00 02 69 FF FO0 9E DVR ID HYBRID REMOTE CONTROLLER ID 0 Displays general information about the HS 86 7 8 Operation 7 8 1 Addition Delete and Modify of DVR Sites 7 8 1 1 Addition of Sites 1 Click SITE ADDITION button And then the fol
15. MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CANCEL RESOLUTION Select 960H D1 or CIF for analog cameras using the mouse or the remote control FRAME RATE _ Set the frame rate for the specified channel The sum of the frame rate values from each channel cannot exceed the maximum frame rates for a specific recording resolution 34 QUALITY Select the recording quality for the selected channel Options are Level 1 Low Level 2 Level 3 Level 4 and Level 5 High RECORDING Assign the recording mode for the selected channel MODE Options are Continuous Motion Sensor Schedule or Disable SENSOR Select the sensor setting for the selected channel RECORDING PRE RECORD Enable disable pre event recording Pre event recording is limited to 20 minutes POST EVENT Set the post event recording time duration for the specified channel RECORD 10 60 seconds AUDIO Enable disable audio recording for the specified channel SCHEDULE To setup a recording schedule select SCHEDULE in the RECORD menu Navigate through the menu items or change the settings using the mouse or the remote control Select CHANNEL gt select NONE CONTINUOUS MOTION or SENSOR gt Highlight area To copy a schedule to a different channel select the channel from the COPY SCHEDULE menu CHANNEL p NONE CONTINUOUS MOTION SENSOR CLEAR COPY SCHEDULE OCH 1 O CH 5 O CH 9 O CH 13 Figure 4 3 2 Schedule Recording
16. PC Requirements CPU Intel Core i3 Resolution 1280x720 OS Windows 2000 XP Professional XP Home Vista 7 NOTE Not all versions of Vista and 7 are supported Direct X 9 0c or Higher Recommended PC Requirements C Intel Core i5 2Ghz or higher V PU 1GB DDR3 or higher 512MB or higher S O Windows 2000 XP Professional XP Home Vista 7 NOTE Not all versions of Vista and 7 are supported 10 100 1000Base T Direct X 10 or higher Before installing the program check the PC specifications The DVR remote software may not perform correctly if the PC does not meet the minimum requirements 67 7 3 Installation of the Program 1 Insert the provided CD in the CD drive and double click SpecoTech Multi Client XXXX exe specotech_multi_ client 3 1 3 1 13 0830 2 Select a destination folder and click Next InstallShield Wizard Choose Destination Location Select folder where Setup will install files Setup will install SpecoT ech Mult Client in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder EA Speca Technologies SpecoT ech Multi Client Browse 3 Select the program folder and click Next InstallShield Wizard L Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below ou map type a new folder na
17. VGA Output LOOP Out Password to secure installation authorization Network software supports 10 100 1000Base T USB 2 0 port for video clip exporting and easy firmware upgrade via USB Flash Drive Exclusive File Format Backup and Player Variety of Ways Network Access via SecureGuarde CMS SpecoTech Multi Client Software Web Viewer and Mobile Viewer E S M A R T Self Monitoring Analysis and Reporting Technology for HDD 10 2 Initial Boot up Process 2 1 Initial Boot up and Basic Time Setup 1 During the first boot up the following logo will be displayed speco technologies 2 After the logo select the language and set date and time as specified below CHOOSE LANGUAGE ENGLISH cf Prev NEXT gt CLOSE initializing system it may take a few seconds or minutes to check the system Initialize Network Done Select EZ Setup EZ Setup will help you to setup your NVR Please select one of the options below EZ Network for Network Setup EZ Record for Date Time and Record Setup EZCamera for Camera Setup NEXT gt gt CANCEL EZ Setup Page Reference Page 16 19 11 2 2 Setting up Daylight Savings Time To enable Daylight Saving feature NTP synchronization take the following steps 1 Enter the SETUP mode The default Username is ADMIN and Password is 1111 LOGIN SETUP USER PASSWORD sot 119994 SEND EMAIL SETUP UN H MWE 0 O 0 Ez Y TIME
18. applies to an individual channel FRAME RATE Sets the recording rate QUALITY Sets the image quality in 5 levels RECORDING Sets the recording mode RECORDING MODE CONTINUOS SCHEDULE MOTION SENSOR PRE RECORD Sets whether to perform or not pre recording POSE EVENT RECORD Sets the duration of the event recording AUDIO Sets whether to perform or not audio recording SECHDULE Sets the schedule recording These settings apply to all channels e EZRECORD O O O O O RESOLUTION Sets the resolution for the recordings The set value applies to an individual channel FRAME RATE Sets the recording rate QUALITY Sets the image quality in 5 levels RECORDING MODE Sets the recording mode RECORD DAYS By the setting value the Recording Days will change accordingly 81 7 7 4 Device Select Device to set Spot Out Enable Disable CVBS Out motion zone SPECO WEB SETUP ni DISPLAY METWORK USER MANAGEMENT STORAGE UPGRADE INFORMATION lt O El IE Br lt i lt lt 8 v S iv SONOS i oe oe a A m N a Hd noQ oa Pra J us no cfa C oe oe ab w in ah a oe NE ao ho e ALARM OUT Set the sensor motion and video loss for triggering alarm relay HDD Error and Video Loss can be set for triggering a beeping sound The following settings can be changed to trigger an alarm output o ALARM DURATION e DIGITAL DETERRENT The schedule of digital deterrent can be set and a sound file c
19. button to view the system information Software Version Storage Size IP Address MAC Address and DDNS Status MODEL NAME D16HS SOFTWARE VERSION Ver 3 9 3 20131206 STORAGE SIZE 435 GB IP ADDRESS 172 16 2 41 MAC ADDRESS 00 02 69 FF FO 9E DDNS STATUS DDNS OFF LANGUAGE Select the display language using the mouse or the remote control Once a language is selected the display language will change DATE DISPLAY FORMAT Select the date display format using the mouse or the remote control Options are MM DD YYYY YYYY MM DD DD MM YYYY YYYY MM DD MM DD YYYY DD MM YYYY DATE amp TIME TUP Select the display date and time using the mouse or the remote control and press OK button to set the present date and time TIME DISPLAY FORMAT 24 HOUR FORMAT TIME ZONE GMT 5 00 Montreal New York DAYLIGHT SAVING USA A ar C SET DATE amp TIME 2013 42 v s zz U 8B OK CANCEL select DAYLIGHT SAVING using the mouse or the remote control and select the appropriate daylight saving time zone The available options are OFF Daylight saving is turned off USA Applies the USA daylight saving time EU Applies the EU daylight saving time Select the GMT AREA using the mouse or the remote control Set the time difference with the standard time using the mouse or the button OTHERS If the time zone is neither USA nor EU set the date and time of the daylight saving period Select BEGIN or END using the remote and press the SE
20. files Disk Info Total space 465 GB Disk full Stop recording 19 7 6 4 Display You can select the OSD On Screen Display to be displayed OSD Site Site 4 Fl All site 4 Event search a ee te Racord Display network statistics Alarm fe Disk 7 Date Time 2 Motion B Display W Sensor Language Record bou Y About W Video Loss Display F Secondary monitor image correction Please use this option only on the PC when having a shattered image on the secondary monitor during use of multi monitor If option is enabled the performance ofthe program may drop 7 6 5 Language English French and Spanish is selectable E General Event Language nglish ES Event search French AB Record English Ld Disk Spanish Display o Language Y About OK J Cancel 76 7 6 6 About About provides network client version information General Event SPECO Multi Client Version 3 0 4 4 Build 110524 ES Event search ES mi Record Copyright C 2011 He This product licensed to isplay E Warnino this computer program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may resultin severe civil and criminal penalties and will be prosecuted to the maximum extent possible under the law OK Cancel 7 7 Remote Setup The menu settings for the DVR unit can be set over network
21. for the VS HS DS RS WRS and HD series DVRs SPECO VIEWER is not compatible with the T Series DVR s TH TN or TL or the PC Series 9 2 1 Live 1 Open the installed Speco Player App and select the Live Preview Then click the menu button of the phone to add a remote device 2 Select the registered device and select LIVE VIEW and select up to 4 channels to monitor Then click START button speco player Live View Playback E ScreenShot Viewer Speco Player 3 The app will display the selected channel s Double tap the channel screen to switch 1 channel display to 4 channels split display ipecotedhnologic speco tedi noloo Mi ok lt PTZ gt FOCUS ZOOM L y NADA 101 9 2 2 Playback 1 Select the registered device and select PLAYBACK and select up to 4 channels to search Then click START button As soon as setting the date and time to search the app will start the playback Set Time 10 minutes later exit 2 The app will display the selected channel s Double tap the channel screen to switch 1 channel display to 4 channels split display Playback 9 2 3 PTZ Control To control the PTZ function of the camera tap the channel screen then the channel name will be highlighted in Yellow Using the PTZ menu icons on the screen control PTZF 11 01 18 29 27 A A FOCUS ZOOM NO N 102 APPENDIX Network Connection LAN 1 Install the network client softwar
22. open Select a number 1digit using a number key then press SEL to start the tour Press the left lt key to stop the tour Preset the number of the tour group in the OSD menu NUMBER For the TOUR and PRESET menu NN Press ESC to return to the main menu 55 5 2 Digital Zoom in Live and Playback Screen DS series supports Digital Zoom feature during live and playback mode 1 Double click the target channel 5 3 SEARCH Screen To enter the search screen menu select SEARCH menu on the screen using the mouse or press SEARCH icon on live screen EZSearch O TIME LINE o EVENT o GO TO FIRST TIME o GO TO LAST TIME o GO TO SPECIFIC TIME o ARCHIVE eo LOG NEXT gt CLOSE Figure 5 3 Search Screen There are 8 search options available such as EZSEARCH TIME LINE Calendar EVENT GO TO FIRST TIME GO TO LAST TIME GO TO SPECIFIC TIME ARCHIVE LIST and LOG LIST on the screen 96 5 3 1 EZSearch The EZSearch window is used to find stored video with ease using the thumbnail playback screen Jan 2014 01 10 2014 pa ms mos ate mos ate i i i i i i Aja ja OONIOURWNE e 1 r 11111111111111311131717 PWNHRO O LEE hhh Ou CHANNEL OCHT CH2 MA E CH4 cCH5 MA A cCHS8 26 27 28 29 30 31 lt PREV NEXT gt CLOSE Figure 5 3 1 1 Calendar Screen Figure 5 3 1 3 24 Hourly Thumbnail Screen Figure 5 3 1 4 Minute Thumbnail Screen
23. periodically DAILY or WEELY or MONTHLY HDD TEMPERATURE HDD BAD SECTOR HDD ALMOST FULL VIDEO CLIP SETUP Setting the duration for pre and post recording EVENTS AND NOTIFICATION HEALTH CHECK RESTART SHUTDOWN PANIC RECORD Enable Email Notification in the event a problem occurs with the VS ALARM IN Enable Email Notification when the camera detects sensor MOTION DETECTION Enable Email Notification when the camera detects motion VIDEO LOSS Enable Email Beep and Alarm output Notification when the camera signal is lost HDD TEMPERATURE Enable Email Beep and Alarm output Notification when the HDD reaches the maximum temperature HDD BAD SECTOR Enable Email Notification when the HDD has bad sectors HDD ALMOST FULL Enable Email Notification when the HDD is almost full HDD FULL Enable Email Notification when the HDD is full HDD FAILURE Enable Email Beep and Alarm output Notification when the HDD fails 80 7 7 3 Record Select RECORD tab to set the recording conditions SPECO WEB SETUP 0 IP CAMERA SYSTEM RECORTE DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE INFORMATION SITE RESOLUTION FRAME RATE QUALITY V H v SENSOR RECORDING AUDIO ON O OFF SCHEDULE NONE v 4 IR 42 13 3 15 OG SE ee 2 24 22 These settings apply to the specified channel only e Recording Setup O O O 0 0 0 O O RESOLUTION Sets the resolution for the recordings The set value
24. previous step 12 Digital Zoom Window in Live and Playback Only available in Single Channel Viewing 7 6 Setup of SpecoTech Multi Client Click the setup icon to setup the configuration of Multi Client software The SETUP window is displayed as below 7 6 1 General Security Option Set a password for security options Select security options and set a password Then when you access any of selected functions you need to enter the password You can also set the save path for capturing and backup Save Path Specify the location to save captured still image for Capture and Backup data Miscellaneous Automatic Reconnection If enabled the software will automatically try to reconnect to the last successful IP address But when CLIENT ACCESS is OFF on the DVR the software will not try to reconnect even if it is enabled Always On Top If enabled the software display will be continuously on the top of other windows Time Format Change the way the Client software displays the time General Security Option F Startup C Shutdown E Setup Event search A Local Playback Remote Playback a Record fel Disk a Display save Path Language Capture CistoragelCapturel amas P About Backup CAStorage Backup Miscellaneous W Automatic reconnection Always On Top Time Format YYYY MM DD 73 7 6 2 Event Event log can be archived and searched Event Log Specify the location to save event logs and sel
25. settings such as Language DVR ID Security User Authentication Security User P W Date format DLS settings Network settings HDD overwrite Limit recording HDD serial number and HDD ERROR time will not be included LOADFACTORY Press the button to reset the system to the factory default settings DEFAULT SOFTWARE Upgrade softeware to the latest version UPGRADE After connecting USB flash drive to USB port on the DVR click SEARCH It will automatically find the upgrade file 90 4 9 1 Firmware Upgrade 1 Create a new folder named upgrade in the USB flash drive root directory 2 Create sub folder for each model under upgrade folder and copy each firmware e For D16HS Models Folder name d16hs File name main _D16HS_speco_ 201 bin e For D8HS Models Folder name d8hs File name main _D8HS_speco 201 bin SD en a i AA Ciganize Shue wath e Eurn New folder z DD i ar Fao E Marne Cute modiied Type Size Hi Desktop dioss 13 19 7011 849 AM File fodder JB Downloads dies 12 15 2011 8 55 AM File folder Plug in the USB flash drive on the rear panel Navigate to CONFIG menu of SETUP select SOFTWARE UPGRADE Follow the procedure from Figure 4 9 2 to Figure 4 9 4 Oy Ol A p MODEL NAME D16HS MODEL NAME D16HS CURRENT SOFTWARE Ver 3 9 3_20131206 CURRENT SOFTWARE Ver 3 9 3 20131206 USB CHECK FOUND USB MOUNT OK F
26. 10 CH11 CH12 CH13 CH14 CH15 CH1 2 EVENT MOTION SENSOR MANUAL CONTINUOUS Mir y2B CHANNEL roa DATE CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS CONTINUOUS 351 log s found 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 00 00 01 01 10 2014 01 00 01 01 10 2014 01 00 01 BACKUP lt PREV PLAY CLOSE Figure 5 3 3 1 Event Search Screen When the Event menu is selected the user can see a calendar which has recorded data Select a specific date and the event log will be displayed Press the PLAY button to playback the data or the SAVE button to save the data after selecting the specific data User can find a data of the specific channel and event using a button in the above red box as following Figure 5 3 10 Press the PREV to return to the SEARCH window 58 Channel vy ALL Y CH1 v CH2 v CH3 vi CHS v CH6 x CH7 v CH9 v CH10 v CH11 x CH13 v CH14 v CH15 Event Y ALL x MOTION vi SENSOR MANUAL CONTINUOUS OK CANCEL Figure 5 3 3 2 Event Search Screen 5 3 4 Go To First Time You can access from the oldest recorded data on the DVR hard drive by selecting GO TO FIRST TIME on the SEARCH window Press the PREV to return to the SEARCH window 5 3
27. 4 164304 2013 11 14 16 53 03 2013 11 14 16 53 03 2013 11 14 16 52 56 Click the mouse right button Select IP Camera Setup Select Channel Number 6000 It launches the camera s web setup page In order for the web pages to launch from the IP Camera Setup menu when accessed from the WAN Ports 59011 to 59254 on the router must be port forwarded to the HS The local address of the HS can be found in the system information 2 6 Dual Streaming e High Quality Main Profile Video Stream is used for both Recording and Live Display e High Quality Main Profile Video Stream can be viewed through the network when selected e Normal Secondary Quality Video Stream is used by default when viewing through the network Monitoring High Normal Selection Network Clients I h d High Quality Video Stream Full HD HDD o enmena Normal Quality Video Stream D1 CIF 20 3 Front and Rear Panels 3 1 Front Panel HS Desktop Front Figure 3 1 1 DVR Front panels Table 3 1 1 Front LED and Ports of Desktop Models D16HS D8HS O neme gt OOO OO POWER LED light is on when power is applied to the system HD LED light is on when the system is recording video data USB Port This USB port for archiving footage into a USB device USB 2 0 connector Table 3 1 2 Front Buttons D16HS D8HS CO name OO oon O O Buttons 1 16 Select a channel from CH1 to CH16 Butto
28. 7 08 54 33 192 188 1 12 5445 Ink connected 2011 04 27 08 54 33 97 9 Network Access Using the Smart Phone Viewer Notice Data Usage applied without Wi Fi connection Please check with your Phone Carrier 9 1 App Viewer for iPhone 1 Enter the Apple App Store 2 Search Speco Player in the App Store Notice SPECO Player is for the HS ZS NS DS RS WRS and HD series DVRs SPECO VIEWER is not compatible with the T Series DVR s TH TN or TL or the PC Series 9 1 1 Live 1 Open the installed Speco Player App and click button to add a remote device 2 Enter the site name IP or DDNS address Network Port number default 5445 ID default admin and Password default 1111 Then click Save button Edit Device List DI6BHS Note Network Port and Web Port must be forwarded before adding a new site 3 Select a registered device and select LIVE Then click CONNECT button Device D16H5 Edit mb Connect Sims EN 98 4 The app will display the selected channel s Double tap the channel screen to switch 1 channel display to 4 8 10 16 channels split display depending on the DVR DI6HS LVE 03 10 14 0347 08 lt DI6HS LIVE 00 10 14 0047 27 5 Toselect the display mode 1 4 9 10 or 16 split display tap the arrow menus button D16H5 LIVE 03 10 14 0047 8 6 Drag and drop channels Touch and drag one channel to the other channel to swap t
29. 9 A A EE A E AE E ta A O T EAE E A A E T E A 40 4 44 Motion Zone UD da 41 Be SCUD DISPLAY MOG nean E A nienre eaannataaacumamenrecs 42 4 6 Setup NETWORK Mode isre a a e a OE 43 A O is NEIWOTK IY OCS via iii E e Aera iban 44 462 DDN So 45 o NE WOIK I OMG WED PON erresire Aar a EE In E N 45 4 6 4 Network SUC Alisa AA EENOK 46 4 7 Setup USER MANAGEMENT Mod ocoococccoccoccccccoccoccoccononccocoocoocconnnononnonnnnnnonnnnonnnnnnonnnaninonos 47 4 0 CUP S TORAGE MOC 00 A a 48 4 9 SCD CONFIG MOE ui aaa 50 4 9 1 Firmware Upgrade nasser e ia cia 51 LIVE Search and PIlayDaACK da E 52 Sl EVE VIEW prame AAA ee er 52 AO a ls 55 5 2 Digital Zoom in Live and Playback Screen oocooccccccocccococoncocononcononcnnononnnnonnnononnnnnnnnnnnannoninaninos 56 DE ARO O o eat 56 I A EZ SEAC q PO ee ee ee eee 57 Ds 9 2 IM UNS ea Cata o o e eo 58 o ae Re eC SM ero nc eee Oe a ene ee ee 58 9 94 50 TO FISTIME dada dia 59 o CA nee ee Ne nen Pe tee ee 59 5 3 0 G0 10 SPECIE MM aa 59 POLANC ANO A O ence ene ree er 59 DO OLO EIS osere eee eee ee EE E E 60 gae Pay MOIE ee e 550 e A 60 6 Back DU E Madan dnne aon oiaiaueaimtas ane wasewednaeuuneeanees 61 6 1 Still Image Backup onto USB Flash DriVe ooccocccocccocconconccononnccononnconncoononnncononnonanconenaninns 61 6 2 Video Backup onto USB Flash Drive during playback oocccoccccccoccocnconcococoncnconancnoncncnnannnos 62 6 3 EZCopy Video Backup onto USB Fl
30. AUDIO IN Audio inputs connections for channels 5 8 or 5 16 through external cable USB USB terminal for video export or firmware upgrade IP CAM Network Second Terminal No Internet access ETHERNET RJ 45 Connector for LAN Connection used for Internet Connection SENSOR IN ALARM OUT RS 485 External sensor terminal External alarm out terminal amp RS 485 for PTZ Camera control POWER DC12V input 22 3 3 Remote Control 60060 0 0A 0000 Typical Remote Control ID To set the remote control ID REC To start and stop manual recording SEARCH To go to SEARCH menu F ADV e During playback To move the playback position 60 seconds forward e During Pause To move the playback position moves 1 frame forward F REW e During playback To move the playback position 60 seconds back e During Pause To move the playback postion 1 frame back FF To fast forward the recording PLAY PAUSE To play or to pause the recording in playback mode REW To rewind the recording ESC During setup To retun to the preivous menu screen During Playback To exit playback mode System lock To lock a system when pressing ESC button for 5 seconds System unlock To unlock a system when pressing ESC button for 5 seconds SETUP To open the SETUP menu Direction buttons To move menu items or select a channel SEQ To start auto sequencing the screen in full screen mode Toggle BACKUP To start a
31. Copy and Setup Easy Search by Thumbnail Preview Easy Network Easy IP Camera Setup Recording Rate D16HS 480fps 960H D8HS 240fps 960H Digital Deterrent audio message output upon event H 264 High Profile compression saves HDD space Simultaneous live view playback while continuing to record network transfer or backup Remote monitoring recording playback configuration and control via internet Wi Fi access point for remote viewing and configuration Audio Recording D16HS 16 Channels D8HS 8 Channels Switch between low and high quality stream during simultaneous Continuous Motion or Continuous Sensor recording modes for storage optimization NOTE Under federal law The Fourth Amendment to the U S Constitution Title III of the Omnibus Crime Control and Safe Streets Act of 1968 as amended by the Electronic Communications Privacy Act of 1986 18 U S C 2510 et seq and the Foreign Intelligence Surveillance Act of 1978 50 U S C 1801 et seq permit government agents acting with the consent of a party to a communication to engage in warrantless interceptions of telephone communications as well as oral and electronic communications Automatic camera detection Plug amp Play Covert camera operation provides enhanced security and administrator control Dynamically programmable recording priority motion detection alarms and scheduling Simple and Easy Graphic User Interface Simple Schedule Recording HDMI Output
32. DD Large Backup to back up from 1 hour to 24 hours PLEASE SELECT MEDIA TYPE O USB DRIVE o USB HDD LARGE BACKUP CALCULATION lt PREV NEXT gt CLOSE 62 3 Once you select the channel and duration the system will start to archive the data to the USB drive EZCopy 2014 01 10 00 00 06 2014 01 10 00 00 07 ALL Y CH 1 ECH 2 CH 3 O CH 5 CH 6 CH 7 CH 9 CH 10 CH 11 CH 13 CH 14 CH 15 FREE CAPACITY REQUIRED CAPACITY 4 The following image shows the progress of archiving the data 5 The following shows the image to complete the backup Select lose to return to the previous screen COMPLETE 6 3 EZCopy Video Backup onto USB Flash Drive during playback Using EZCopy feature Video can be easily archived onto the USB flash drive or a hard drive In playback mode press the ez EZCOPY button to launch the backup function 1 Press EZCOPY button on the selected channel or all channels ad a mad 2 Then EZCOPY START time will display 11 18 2013 11 51 00 PLAY ORO To mA Tee 11 18 2013 11 50 49 63 3 Move Tine bar cursor to the time of end of backup and press EZCOPY button Then EZCOPY STOP time will display 11 18 2013 11 52 27 PLAY 4 EZCOPY window will display The DVR will ask whether to archive a Still Image a NSF or AVI EZCopy 2014 01 10 00 00 06 2014 01 10 00 00 07 SELECT FILE FORMAT _ NSF PROPRIETARY FORMAT AVI INTEGRATED SUBT
33. DISPLAY FORMAT TIME ZONE DAYLIGHT SAVING L SET DATE TIME 12 2 3 Setting NTP Network Time Protocol 1 SETUP gt SYSTEM gt NTP SETUP gt ON SYSTEM DESCRIPTION LANGUAGE ENGLISH DATE DISPLAY FORMAT DATE amp TIME SETUP CLIENT ACCESS NTP SETUP SEND EMAIL SETUP UNIT NAME SYSTEM RESTART SYSTEM SHUTDOWN EZ SETUP SYSTEM EVENT NOTIFICATION HYBRID SETUP o de ma e O 0 0 ld 1 e CANCEL 2 Select the proper TIME ZONE time PRIMARY SNTP SERVER Pool ntp org A SECONDARY SNTP SERVER Time nist gov A TIME ZONE GMT 5 00 Montreal New York CONNECTION MODE TIME CONNECTION PERIOD 03 00 AM OK CANCEL Table2 3 1 GMT Time Zone OO se andar time Daylight Saving Time 13 1 Hawaii GMT 10 oho ara E mw O o A o o Ne Nebraska mam Te Nebraska oma G Tw Neves Se nH Newempsnie oms oma es IT T y no torta ome oms no North Dakota oma O ome on omo ms o oa o Oviehoma ma S OR own ma mr IN AECI E BE R so TN Tennessee E GMT 5 GMT 4 Tennessee W NOTE If you want the unit to automatically synchronize the local time the Time Zone must be properly set according to your local time zone 15 2 4 EZ SETUP Quick installation Menu for HS and IP Camera Easy installation Right Click on the Main Screen Figure 2 4 EZ Setup Screen 2 4 1 Setup DATE amp TIME IP CAMERA configurations SETUP PROFILE amp PREVIE
34. ESS 172 16 2 46 SEND EMAIL SERVER TYPE MANUAL E MAIL SERVER a MAIL PORT 25 lt H SECURE OPTION NONE X ID EN PASSWORD ai MAIL TO re MAIL FROM Pa 2 SERVER TYPE Select GMAIL HOTMAIL AOL YAHOO or MANUAL MAIL SERVER Enter the appropriate mail server information MAIL PORT Assign Mail Port number SECURE OPTION Select the secure mail server connection method SSL or TLS 31 ID Enter the appropriate mail server ID PASSWORD Enter the appropriate mail server PASSWORD MAIL TO Enter the appropriate email address to enable sending e mail reports using a virtual keyboard MAIL FROM To set the email address sent to the destination host TEST E mail settings sent a test mail to the registered account UNIT NAME Name the DVR e g Factory Library Store Location etc This is to used to identify the name of each DVR under the same network SYSTEM RESTART Restart the system SYSTEM Shut down the system SHUTDOWN EZ SETUP Helps user to easily setup NETWORK RECORDING and IP CAMERA SYSTEM EVENT NOTIFICATION DISK EVENT SETUP HEALTH CHECH VIDEO CLIP SETUP PRE RECORD SSD BAD SECTORS HDD TEMPERATURE 60 140F HDD ALMOST FULL 3 SECOND S POST RECORD EVENT AND NOTIFICATION HEALTH CHECK RESTART SHUTDOWN PANIC RECORD ALARM IN MOTION DETECTION VIDEO Loss HDD TEMPERATURE HDD BAD SECTORS HDD ALMOST FULL HDD FULL HDD FAILURE ALA
35. ILE CHECK main_d16hs speco 3 9 3 20131206 bin 0 0 SCAN CANCEL UPGRADE CANCEL Figure 4 9 2 Figure 4 9 3 MODEL NAME D16HS CURRENT SOFTWARE Ver 3 9 3 20131206 USB CHECK FOUND USB MOUNT OK FILE CHECK main_di6hs speco 3 9 3 20131206 bin 100 UPGRADE SUCCESS RESTART NOW Figure 4 9 4 NOTICE If selecting REBOOT NOW when the USB flash drive is plugged the following message will pop up Remove the USB flash drive and select OK 91 5 Live Search and Playback 5 1 Live View In the Live screen video inputs from the cameras are displayed as they are configured in the Display Setup screen Various On Screen Display OSD symbols which indicate the status of the DVR are described in Table 5 1 1 CH1 CH2 CH3 CH4 NO VIDEO NO VIDEO NO VIDEO NO VIDEO CH5 SEARCH SETUP CHT CH8 DISPLAY NO VIDEO NO VIDEO NO VIDEO CH9 NO CONNECTION NO CONNECTION 172 16 2 66 0 0 0 0 CH13 SNAPSHOT SUPER EZ COPY ENABLE MANUAL RECORD INSTANT PLAYBACK es SETUP CH12 ADVANCED MENU ect i CAMERA PT2 YO CONNECTION ENABLE MAIN MONITOR SEQUENCE 0 0 0 0 DISABLE ALARM OUT x MANUAL DIGITAL DETERRENT CHi4 SITE INFORMATION CH16 SYSTEM INFORMATION NO CONNECTION NO CONNECTION EXPORT HELP NO CONNECTION 0 0 0 0 0 0 0 0 SYSTEM LOCK 0 0 0 0 Figure 5 1 1 Live Screen and Quick Operation Window Table 5 1 1 Status Indicator Icons in Live Viewing Screen Icon Description
36. ITLE AVI SEPARATED SUBTITLE MAC COMPATIBLE NEXT gt CLOSE 5 After backup format is selected also select media type and channel s to archive the data to the media 64 6 4 Transferring Still Images or Video from the ARCHIVE List The stored data in the hard drive can be found in the ARCHIVE list in the SEARCH window User can back up still images or video into the storage device from the ARCHIVE list 1 Select the date to begin searching and navigate through the days using the mouse or the remote control Once you have selected the date press the NEXT button to open the list of stored data Use the mouse or the remote control to scroll through the archive list Select a list of stored events in the archive list A A e Once the desired event has been selected press the DISPLAY button to view the still image or the first frame of the selected video 6 Press the BACKUP button to launch the archiving function in playback mode 7 Press the CLOSE button to return to the SEARCH window PLAY BMP SPLIT 11 15 2013 13 45 49 11 15 2013 13 55 44 NO DATA Backup _ _ _J _ gt 2 log s found PLAY BMP SPLIT MEDIA use X 11 15 2013 10 25 39 lt PREV DISPLAY CLOSE Backup CLOSE Figure 6 3 1 Archive Search Screen 6 5 Playback of Backup Video 6 5 1 AVI Format AVI format AVI format video can be played back by Window Media Player or other media player that is compa
37. L button Caution Do not set the start time to 23 00 for DLS DLS cannot be applied if the date of BEGIN and END is the same CLIENT ACCESS Enable Disable remote access through the network NTP SETUP NTP Network Time Protocol which synchronizes the time of the computer systems over variable latency data networks 30 PRIMARY SNTP SERVER Pool ntp org lt A SECONDARY SNTP SERVER Time nist gov a TIME ZONE GMT 5 00 Montreal New York CONNECTION MODE TIME CONNECTION PERIOD 03 00 AM PRIMARY SNTP SERVER Input the address of the primary NTP time server SECONDARY SNTP SERVER Input the address of the secondary NTP time server TIME ZONE NTP synchronizes with GMT Greenwich Mean Time regardless of geography user must set their own time difference CONNECTON MODE Select the NTP time server connection mode from TIME INTERVAL and ONCE CONNECTION PERIOD TIME Refresh the time at the designated time e g 1AM INTERVAL Every 1 hour 24 hours ONCE Synchronizes time only once NTP will not synchronize unless the Connection Mode is changed sends E MAIL Notification when the NTP server time is faster than the system time with bellow message NTP server time is faster than the system time In this case NTP server time is ignored to protect the user data User must set the time manually SYSTEM TIME Mon Oct 10 13 46 49 2011 SERVER TIME Mon Oct 10 13 33 12 2011 DVR ID DVR IP ADDR
38. LIENT CAPTURE Click this icon to capture a still image i _ LIST Opens list of events logged by the Multi Client PAUSE Click this icon to play pause live video aN ARM ON Click this icon to turn on off alarm outputs Enable or disable recording of live video to local disk which has set in RECORD ON setup menu Use the volume control bar to set the audio level AUDIO Use the microphone volume control bar to set the micro phone level ae Os User can control PRESET TOUR SCAN MENU PRESET TOUR SCAN MENU E EM EN E To select the numbers of display channel channels Single quad 9 channels and 16 channels of highlighted site To select the numbers of DVR DVRs 1 DVR 4 DVRs 9 DVRs 16 DVRs on main display screen 70 7 5 Search and Playback Window 7 5 1 Main User Interface You can access to search window by clicking the search icon Local Playback Remote Playback on the upper right of the Live Window speco technologies SPECO Multi Client Ver 3 1 3 8 7 5 2 Main Control Panel fe _ ti viniatninema niin Click this icon to run a playback window to search and play videos that Click this icon to run a playback window to search and play videos that D16H5 ES THUMBNAIL REFRESH Click this icon to refresh and renew IP 172 16 2 57 thumbnail image of the connected sites Ey SITE ADDITION Click this icon to open Site Addition window E SITE DELETE Click this icon to delete site from the ind
39. O DEA asco eo 87 7 8 1 Addition Delete and Modify of DVR Sites oocooccoccccnconconconconconcononcocononnconcononcnononconnnnoos 87 1 9 2s CONNEC and DISCOS Clon dia 89 7 8 3 Still image Capture During LiVE occcoccconcccnconcococcnconoccnnononononnnnononnnnnnnnnonanonnonanencnnnninanenes 89 7 8 4 Recording Video on Local PC During Live ocooccccccccncociconconcccncononcnonnonanonnnnononnnnnnnncnnannnos 90 7 8 5 Local Playback and Remote Playback occoocconcoccocccccoccococcooconcnonncoconconnnonnonnnnnnnnnnnnanonoos 91 T O OAV BACkUD GUNNO PA VDACK citeaiicia iia tiociicccids 93 8 Network Access Using the Web Browser Viewer oocoocooccoccccnconconconoonooncononnoncnnnnnnnonnnnnonnnononnonnnnns 96 9 Network Access Using the Smart Phone Viewer oocccoocccoccocncocoocnconcococoncncnnnnonononnnnononnnnancnnonannnoos 98 9 12 ADD Viewer TORINO Cra 98 A eer ere ace eh eee eee Cen emery earn Ten ee ee re ene Men AN Te ee eee neon 98 9 12 PTZ CONTO A eo PP o nn A 102 A E E chat A E EA ohne Malaancisebangne E E 102 9 2 App Viewer for Android PRONG iii id 102 eM B E E A E E E eee ete cee came E E T E E E E E L A 102 22 23 PA DA ii 102 AAA A A 102 o os cccsscecceccussussuseuusursursussasccussuusursassasersarsascesccsccersarsascess 103 APPENDIX Network Connection Internet and DDNS ocooccocconccnccoccoccococccociocooccocnconconoononnonononnnos 105 po A 107 1 Main Features Easy Record
40. QUENCE SEQUENCE DWELL TIME SPOT CHANNEL ALL al a a sid E 1 al Be ee Figure 4 4 3 SPOT OUT Setup Screen Table 4 4 3 Menu Item in SPOT OUT Setup Screen Item Description SPOT ON EVENT Enable disable channel change if an event occurs on a channel SPOT EVENT Set the dwell time for the display of the event activated channel DWELL TIME 3 10sec SEQUENCE Enable disable sequential display of spot channel in full screen If select ON the selected channel will be displayed on the monitor periodically SEQUENCE Set the dwell time for the spot channel display 3 10sec DWELL TIME SPOT CHANNEL Select a channel for spot monitoring using the mouse or the remote control and press OK button 40 4 4 4 Motion Zone Setup Select MOTION ZONE using the mouse or the remote control and select either PARTIAL ZONE or FULL ZONE using the mouse control The default value is FULL ZONE If FULL ZONE is selected the motion zone grid screen is not displayed Only set the level of sensitivity for MOTION SENSITIVITY FULL ZONE The motion sensor is active on the whole screen PARTIAL ZONE The motion sensor is active in the set detection frame Select the motion detection position using the mouse or the remote control Then left click on the mouse or left click and drag the mouse pointer to select or deselect the area Highlighted area indicates the partial motion detection zone Press the ESC button or right click on t
41. RM OUT La i i i i a j j J HEALTH CHECK OFF ON Allows the user to set MAIL STATUS periodically DAILY or WEELY or MONTHLY 32 DAILY z FIRST SUN z lo H x VIDEO CLIP SETUP Setup the duration of video clip for PRE RECORD and POST RECORD EVENT AND NOTIFICATION OFF ON Allows the user to set EVENT NOFICIATION ON or OFF HEALTH CHECK RESTART SHUTDOWN PANIC RECORD Enable Email Notification in the event a problem occurs with the VS ALARM IN Enable Email Notification when the camera detects sensor MOTION DETECTION Enable Email Notification when the camera detects motion VIDEO LOSS Enable Email Beep and Alarm output Notification when the camera signal is lost HDD TEMPERATURE Enable Email Beep and Alarm output Notification when the HDD temperature HDD BAD SECTORS Enable Email Notification when the HDD has bad Sectors HDD ALMOST FULL Enable Email Notification when the HDD is almost full HDD FULL Enable Email Notification when the HDD is full HDD FAILURE Enable Email Beep and Alarm output Notification when the HDD fails HYBRID SETUP HYBRID SETUP SELECT THE NUMBER OF ANALOG CHANNEL S OTHER CHANNEL S WILL WORK AS THE IP CHANNEL S THE NUMBER OF ANALOG CHANNEL S 8 THE NUMBER OF IP CHANNEL S CANCEL Each channel can be configured to be Analog or IP Camera However Analog channels take priority to ip cameras when it comes to c
42. SPLAY FORMAT 12 HOUR FORMAT TIME ZONE GMT 5 00 Islamabad DAYLIGHT SAVING EU GMT AREA 04 00 IITTI IIIIITITITTTTTTIIITTIITTITTTITTTTIIITITTIITITIIIIITIIIIIIITTITTTIIIIIIIIIIITITITTTI ry SET DATE amp TIME EEE Oe ORE Ne RENE e CLIENT ACCCESS Enable Disable remote access through network client software e NTP SETUP Sets whether to synchronize the time using NTP server or not 79 O O O Primary SNTP Server Input the NTP primary server address Secondary SNTP Server Input the NTP secondary server address Time Zone Select the time zone Connection Mode Select the connection mode to NTP time server SEND E Mail SETUP Sets whether to enable disable e mail sending function O O O SEVER TYPE Select GMAIL HOTMAIL AOL YAHOO or MANUAL MAIL SERVER Input the SMTP server name as well as the user ID and password MAIL PORT Mail port setting SEURE OPTION Select a secure mail server connection SSL or TLS ID Email User ID PASSWORD Email User Password MAIL TO Input the appropriate email address to enable sending e mail reports MAIL FROM Return Mail Address Set the source e mail address to be notified to the destination SEND MAIL TEST E mail settings sent a test mail to the registered account UNIT NAME Name the HS SYSTEM RESTART Restart the system SYSTEM EVENT NOTIFICATION Allows the user to set EVENT NOFICIATION ON or OFF O HEALTH CHECK Allows the user to set MAIL STATUS
43. Setup Screen e NONE Disable recording during selected timeframe Highlighted in White e CONTINUOUS CONTINUOUS recording Highlighted in Green e MOTION MOTION recording Highlighted in Yellow e SENSOR SENSOR recording Highlighted in Red CLEAR Clears the schedule 35 4 4 Setup DEVICE Mode In the SETUP menu select the DEVICE tab Then the device menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control Y DEVICE ALARM OUT BEEP DURATION DIGITAL DETERRENT CONTROLLER PTZ SPOT OUT SITE CH 1 Vv MOTION ZONE FULL ZONE U EA A A MOTION SENSITIVITY KEY TONE REMOTE CONTROLLER ID SENSOR TYPE VIDEO INPUT TRIMMING APPLY CANCEL Figure 4 4 DEVICE Setup Screen Table 4 4 Menu Items in DEVICE Setup Screen Item Description ALARM OUT Only one Alarm out is available BEEP DURATION Set alarm dwell time from 5 to 60 seconds or infinite ALARM OUT 1 F ALARM DURATION Man ox ANGEL DIGITAL DETERRENT Setup schedule and audio recordings for Digital Deterrent CONTROLLER amp PTZ Set the PTZ baud rate protocol and ID SPOT OUT Display the channels triggered by an event Refer to 4 4 4 SITE Select specified channel for motion zone setup MOTION ZONE Select either Full Zone or Partial Zone for motion detection MOTION SENSITIVITY Set the motion sensitivity for the selected channel Control the mot
44. System allows a DNS name to be constantly synchronized with a dynamic IP address It allows using a dynamic IP address to be associated with a static domain name Once the setting is completed the DDNS address will be http hostname ddns specoddns net For example if you enter the host name as D16HS then the address will be http D16HS ddns specoddns net Select NETWORK gt DDNS The menu displays as below ENABLE DDNS HOST NAME hostname SUBMIT UPDATE ezDDNS APPLY CLOSE Figure 4 6 3 NETWORK Setup Screen DDNS Table 4 6 2 DDNS Item Description ENABLE DDNS Turn DDNS on off HOST NAME This item allows the user to setup a domain name manually using virtual keyboard displays as shown SUBMIT UPDATE When manual host name input is done move the cursor to this item and select ON to submit the settings ezDDNS Enable disable ezDDNS to register the host name automatically 4 6 3 Network Port and Web Port Connecting DVR DVRs through a common IP sharing device each DVR must be assigned a unique TCP port number for access from outside the LAN This port number is displayed on NETWORK gt NETWORK PORT Setup MENU NOTE If you access the DVR only within the same LAN the TCP port number does not need to be changed 45 Network access beyond a router To access DVR beyond a router firewall you must open the proper TCP ports for live playback streaming for commands for remote backup and for aud
45. W are not available in the setup menu 3 3 3 3 3 3 192 168 78 11 SETUP PROFILE amp PREVIEW are not available in the setup menu Figure 2 4 1 EZ CAMERA Setup Procedure Select EZ Camera for Date Time and Camera Setup Click NEXT to proceed Configure individual cameras in the EZ Camera Setup e Select the Channel to configure e Select the Camera Protocol and then click on the scan button this will scan the network for any ip cameras using the specified protocol e Select the desired Camera from the list and then click on register e If necessary click on Preview to Preview the camera or Setup to change camera settings 16 2 4 2 EZ NETWORK Using an internet connection Figure 2 4 2 EZ NETWORK Setup Procedure Select YES in case of setting the network using an internet connection Select Auto Configuration DHCP or Manual Configuration STATIC and then click TEST Button It will automatically setup the network for the system G Setup DDNS setting DDNS Dynamic Domain Name System allows a DNS name to be constantly synchronized with a dynamic IP address It allows using a dynamic IP address to be associated with a static domain name Refer to the full version manual for more information 4 Click Finish to save the setup
46. a is recorded as set in Record and Disk setup These video data can be searched and play backed with Local Playback 90 fe NCO1 DER File Edit View Favorites Tools Help Ha Q Back gt Dd A Search eer Folders l XxX mg EE de Address C C Storage H NCO1 v Go Name Size Type Date Modified 20090608 File Folder 6 8 2009 4 00 PM 320090610 File Folder 6 10 2009 3 16 PM co 20090317 ndl 4 275 KB NDL File 3 17 2009 6 24 PM E 20090317 _0 ndb 102 402 KB NDB File 3 17 2009 5 35 PM 1 20090317_1 ndb 102 403 KB NDB File 3 17 2009 5 44 PM Sf 20090317_2 ndb 102 402 KB NDB File 3 17 2009 5 52 PM i 20090317_3 ndb 73 845 KB NDB File 3 17 2009 6 23 PM 7 8 5 Local Playback and Remote Playback 7 8 5 1 Playback of Recorded Video on a Local PC 1 Click A LOCAL PLAYBACK And then Playback Window will be displayed over the Live Window speco technologies SPECO Multi Client Ver 3 1 3 8 2014 07 08 00 00 00 EZSearch 2 Select site sites to connect from the directory window A E 3 Click UE CONNECT button And then Green bar displays on Search calendar and timeline scale window ma TETES CODE 4 gt Ve A a A i i P 6 T 3 9 40 11 2013 5 J 13 14 15 16 17 18 May Bao 21 22 23 24 25 GE 27 28 29 30 31 6 Move the marker on the timeline scale to where there is video data and press the PLAY button 16 16 91 7 Video data that is recorded on local PC will be play back
47. a selected channel INFORMATION SYSTEM Press the button to view the system information INFORMATION MODEL NAME D1GHS EXPORT HELP Displays window with instructions for exporting video SYSTEM Locks the HS from unauthorized user access LOCK SYSTEM Select this option to shutdown system SHUTDOWN 54 5 1 1 PTZ Control Table 5 1 3 Menu Items in PTZ Control Window INITIALIZE Initialize the PTZ settings of the selected camera PAN TILT ZOOM FOCUS AUTOSCAN PRESET TOUR Select PAN TILT using the AV 4 and p button then press SEL Adjust the tilt UP DOWN pan LEFT RIGHT position using the AV dand P gt buttons Select ZOM FOCUS using theaw lt dq and P gt buttons then press SEL Adjust the zoom UP DOWN focus LEF T RIGHT position using the AV 4 and buttons Select OSD to enter the menu Control keys are Right Left UP Down Select Far REW KEY and Near FF KEY Press the ESC button to return to the previous menu Press the PTZ button to close the OSD menu Press the right key gt to start auto scan Press the left key lt to stop auto scan Select PRESET then press the left key 4 A number input window will appear Set the number 3digits using the number key then press the SEL to confirm the preset number for the current position Press the right key gt and enter the number 3digits to go to the preset position Select TOU and press the right key A number input window will
48. all channels OSD Sets whether to display or not date and time as well as channel number on the screen OSD CONTRAST Adjust the character contrast on the screen MAIN MONITOR SEQUENCE Setting for automatically switching the displayed video SEQUENCE DWELL TIME Sets the interval for automatically switching the screens SITE Name Covert Brightness Contrast Hue Saturation These settings apply to the specified channel only 83 7 7 6 Network SPECO WEB SETUP srna IP CAMERA SYSTEM RECORD DEVICE DISPLAY ETWORK USER MANAGEMENT STORAGE UPGRADE INFORMATION NETWORK TYPE IP SUBNET MASK GATEWAY DNS PRIMARY DNS SECONDARY DDNS ENABLE DDNS HOST NAME SUBMIT UPDATE ezDDNS NETWORK PORT NETWORK AUDIO PORT WEB PORT NETWORK STREAM RESOLUTION FRAME RATE QUALITY USE MOBILE WIRELESS LAN IP ADDRESS SSID KEY 8 15 CHARACTERS 12345678 e NETWORK TYPE Cannot be altered remotely o STATIC The address setting mode is manual Input IP Gateway Subnet Mask and DNS IP o DHCP The address setting mode is automatic e DDNS Set whether to use DDNS service or not o HOST NAME Allows the user to setup a domain name manually o SUMBIT UPDATE Select ON to submit the settings o ezDDNS Enable ezDDNS to register the host name automatically e NETWORK PORT When connecting multiple DVRs to the network set a unique port number e NETWORK AUDIO PORT Display the network audio port NETWORK PORT 1 e WEB PORT Seta web server port num
49. ame SpecoTech WebViewer verl 4 6 Verified publisher Speco Technologies File origin Downloaded from the Internet Y Show details Change when these notifications appear 5 The Web Browser Viewer will be displayed as below after the ActiveX installation ff Connect speco technologies al Live Je Search 2013 11 18 14 03 40 WebViewer Ver 2 1 1 6 BitRate 0 0 Kbps E Startup 2013 11 18 14 03 36 730 je 20 ue a O oul 6 Click the CONNECT button on the Left upper corner of web viewer Then Connect dialog is displayed asa ta Connect to remote system IP Address Port No ID Password e Site Name Input a name that properly describes a site e IP Address Input IP address Public IP address of a router that DVR is connected or Domain name e Port Number Default Port Number is 5445 e ID Input ID of DVR Default ID is admin e Password Input network password of DVR Default Password is 1111 Then the cameras connected to the DVR are displayed on the screen Use mouse scroll to digitally zoom in and out from a single channel display eg Disconnect sil Live JO Search 1 97 19 57 42 12 168 1 12 3 Date Time 192 168 1 12 5445 Camera detected CH 1 2011 04 27 08 54 34 192 168 1 12 5445 camera detected ch 2 2011 04 27 08 54 34 192 188 1 12 5445 camera detected ch 3 2011 04 27 08 54 33 192 168 1 12 5445 camera detected ch 4 2011 04 2
50. an be uploaded to the HS To set up schedule select CHANNEL gt select SOUND TYPE gt select Area e CONTROLLER Set the controller baud rate and ID e PTZ Set the PTZ baud rate protocol and ID e SPOT OUT o SPOT ON EVENT Enable disable channel change if an event occurs on a channel o SEQUENCE Enable disable sequential display of spot channel in full screen o SPOT CHANNEL Select a channel for spot monitoring using the mouse or the remote control and press OK button e MOTION Setup the motion detection area and the sensitivity o SITE Select the channel o MOTION ZONE FULL Zone or PARTIAL Zone o MOTION SENSITIVITY 1 9 High sensitivity level e CHANNEL Select the Channel to configure audio input o AUDIO SOURCE Local Audio RCA or IP CAM Audio e KEYTONE Sets On or Off of Key Tone e REMOTE CONTROLLER ID Sets an ID number of which remote control to receive commands e SENSOR Select the type of sensor 82 7 7 5 Display Select the DISPLAY tab to set the DISPLAY conditions SPECO WEB SETUP veios IP CAMERA SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE INFORMATION OSD CHANNEL NAME O ON OFF VIDEO LOSS OON 0 OFF STATUS BAR ICON ON 0 OFF IP ADDRESS FPS OSD CONTRAST 100 MAIN MONITOR SEQUENCE ON OFF SEQUENCE DWELL TIME 3 SECOND S SITE NAME COVERT BRIGHTNESS CONTRAST HUE SATURATION fafafa ojojoj Q ale 2 TES Boe a4 f 4 lt 4 lt These settings apply to
51. an see a calendar which has a log data Select a specific date and press NEXT button and then the log data will be displayed Press the SAVE button to save the data and then the data is saved as a text file format 5 4 Play Mode During playback of a recorded event the mode changes from SEARCH to PLAY While in PLAY mode you may return to the SEARCH screen by pressing the X button on the status bar ef ib a E gt d 2B sa F Tr aa e CH3 NO DATA 11 15 2013 10 25 36 O ii me T el pay PE EF Figure 5 4 1 Play Mode Screen The following status bar hides automatically and appears again if a mouse pointer is positioned to the bottom of the screen 60 Table 5 4 1 Button Functions in PLAY Mode Button Description e 2x 4x 8x 16x 32x speeds at 4 split screen e 2x 4x 8x 16x at 9 split screen e 2x 4x 8x at 16 split screen e Single Channel backward playback speed 1x 2x 4x 8x 16x 32x 64x Jump Step backward The playback position moves 60 seconds backward Press to play or pause recorded video Jump Step forward Playback position moves 60 seconds forward e 2x 4x 8x 16x 32x speeds at 4 split screen e 2x 4x 8x 16x at 9 split screen e 2x 4x 8x at 16 split screen Single Channel forward playback speed 1x 2x 4x 8x 16x 32x 64x Slow Mode play Forward playback speed x1 4 x1 2 Press to backup the video EZCopy button Return to the previous men
52. ash Drive during playback occoocccoccccncocconcconcoconannnns 63 6 4 Transferring Still Images or Video from the ARCHIVE LisSkt o occcoccoccoccoccocccnnoncocnccncnncnnnnoss 65 6 5 Playback of BacKUD MASON 65 O 15 AV 1 FOM alres E AAA e 65 EFAN O a a E E E 66 7 Network Access Using the Multi Sites Network Viewer occooccoccoccoccoccoccocconcocnonncoconcnonnnnncnnons 67 PA ON NN ia ra 67 2 PO REGUTEMENS orenera a A A 67 7 8 Installation ofthe Progra M saires a Gade nace etn ened ad 68 LA GVE Nd Wa is 69 fAs Mam SSI teta cnn tra 69 AZ GONTOLBUIDOA Sis 69 7 5 SGalGh ana Playback W IN GOW sac vcomtcns const doves uaueinees cenmuce nance cued E 71 7 921 Mam User Menta ciisoe 2icizad dic tda E 71 A A O wumsecisareeancaneeeamadenies 71 1 6 Setup of Speco TECH Multi Clean AAA eabannawadinds 73 Fo Ws CIV A O AN 73 POLE diia 14 OR O E E A me ey mee ee er ener 15 TOF WIS A e A A 76 100 LANUS AE o a a a 76 FODA DOUN A one e O E 77 A A ice an ere eee ey eee er eee eee ee eee eee 17 AA A o A A delea a iad 78 A E LE A EEEE ten et cote Sat ater acne pasta T E ates Seen areca E E cence beater E T 79 A A A E e asta taindns ebavaus eed eeeeasacinseu aaa aawbheeiascovauaaminnias 81 Tey coon Doh clo yee erect ree A AE na E E ee Rar ene E A eer eg Pe en EA te nea 82 Taf OD ISDIAY ad 83 TT OI UN VO NE e des 84 TT IMAM AGS ad 85 MEA EAA A EE A A E A E A a hanaa A E 86 VES REMETU ad incita 86 FIAT IRONMAN a os 86 ES
53. backup operations in live or playback mode 0 9 To select channel 1 2 3 or to enter a DVR ID number or use as number key 23 4 Setting up the DVR The following sections detail the initial setup of the DVR Menu screen will close if user response is not received in 5 minutes 4 0 Setup Main Live Screen To enter the setup menu right click on the mouse and select setup from the submenu or press the setup button on the remote control CH1 NO VIDEO CH5 NO VIDEO CH9 NO CONNECTION 172 16 2 66 CH13 NO CONNECTION 0 0 0 0 CH2 CH3 NO VIDEO NO VIDEO CH7 NO VIDEO NO CONNECTION 0 0 0 0 chia NO CONNECTION 0 0 0 0 CH4 NO VIDEO CH8 NO VIDEO O CONNECTION 0 0 0 0 CH16 NO CONNECTION 0 0 0 0 IEC PAG OF HDD OVERWRITE Table 4 1 1 Live Screen and Quick Operation Window ADMIN PASSWORD USER PASSWORD When the DVR prompts the LOG IN window enter the PASSWORD using the virtual keyboard or the front panel or the remote control The factory default password is 1111 It is highly recommended to assign a new password to protect the system User can assign a new password in SECURITY setup menu 24 4 1 Setup IP CAMERA Press the SETUP button and enter the password The setup menu is displayed as picture below Select DISPLAY icon and press SEL button to enter the setup menu item ld a e 84 Figure 4 1 1 IP Camera mode setup screen
54. ber e NETWORK STREAM Set the Resolution Frame Rate and the Quality e WIRELESS LAN Wireless networks can be configured option o IP ADDRESS Wireless IP Address o SSID Service set identifier Wireless Network ID o KEY 8 15 Characters Wireless Network Password 84 7 7 7 User Management Select the USER MANAGEMENT tab to set the DISPLAY conditions SPECO WEB SETUP seins IP CAMERA SYSTEM RECORD DEVICE DISPLAY JSER MANAGEMENT STORAGE UPGRADE INFORMATION AUTHORITY SETUP PASSWORD SETUP REC OFF NETWORK PASSWORD CHECK ADMIN USER1 USER2 USER3 NEW PASSWORD i CONFIRM PASSWORD PLAYBACK AUTHORITY y y Y y ADI v 4 v ADMIN USER1 USER2 USER3 e AUTHORITY SETUP Select which users have access to each function password check can be implemented for each function accessed e USER NAME SETUP Select which Username to change o NEW USER NAME Input the new username e PASSWORD SETUP Select Username to change Password A CHANGE Select whether to KEEP or CHANGE the current password B NEW PASSWORD Input NEW Password if CHANGE was selected C CONFIRM PASSWORD Input NEW Password again to confirm e PLAYBACK AUTHORITY User can select which users have access to which channels 85 7 7 8 Storage Select Storage to configure continued recording settings by overwriting the hard disk and the storage period for the recording data SPECO WEB SETUP o 0 IP CAMERA SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT
55. ble 5 1 2 Menu Items in Quick Operation Window Icon Description SEARCH Search button Click this button to enter the search menu SETUP Select this option to enter the Setup menu DISPLAY Select between different multi view display formats SNAPSHOT Capture pictures and store as BMP files SUPER EZ COPY Select this option to start EZ Copy Wizard 99 ENABLE MANUAL RECORD INSTANT PLAYBACK Manual Record button Click this button to enable manual recording Go back to the specific time and play the recoding data ADVANCED MENU IGO BACK TO 20 SECONDS GO BACK TO 30 SECONDS GO BACK TO 60 SECONDS It doesn t ask the password It does work witout error while the recording mode is CONTINUOUS On other recording mode it may not work normally ADVANCED MENU EZ SETUP Select this option to start EZ Setup Wizard CONNECT Select this option to disconnect connect from IP Camera AUDIO MUTE Select this option to mute audio on all channels CAMERA PTZ Pop up the PTZ user interface ENABLE MAIN sequence button Click this button to use a sequence function MONITOR SEQUENCE DISABLE Click this button to enable disable Alarm outputs ALARM OUT MANUAL Select this option to manually trigger any of the saved Digital DIGITAL DETERRENT Deterrent messages Manual Digital Deterrent Select Digital Deterrent Source Source Name Default Y OK CLOSE SITE Press the button to view the record setting of
56. can connect to it by the static name Enable disable using domain name address through DDNS server NETWORK PORT Enter the port number Default 5445 NETWORK AUDIO Display the network audio port NETWORK PORT 1 PORT WEB PORT Enter the port number for connection using web NETWORK Sets the camera display settings for network streaming STREAM WIRELESS LAN 1 Connect USB Wifi Dongle to USB connector on DVR 2 Load the application on your smart phone or PC and enter the WIFI IP ADDRESS 3 Find the WIFI SSID and enter the password shown in image below 4 Then the remote viewing and configuration can be used IP ADDRESS 192 168 50 1 SSID MY_SSID KEY 8 15 CHARACTERS 12345678 APPLY CANCEL There is a distance limitation for the Wireless LAN 4 6 1 Network Types 4 6 1 1 DHCP An IP address is automatically assigned by the DHCP server which automatically assigns the IP address and other parameters to new devices 4 6 1 2 STATIC IP address Subnet Mask Gateway and DNS are manually assigned by the user e IPADDRESS The fixed IP address of the DVR unit 44 e SUBNET MASK The subnet mask for the LAN e GATEWAY The IP address of the Gateway e DNS PRIMARY The primary address of Domain Name Server e DNS SECINDARY The secondary address of Domain Name Server NOTE Unless DNS is properly set the DDNS and the e mail features will not work 4 6 2 DDNS DDNS Dynamic Domain Name
57. e from the supplied CD 2 Check the IP address from SETUP gt SYSTEM gt DESCRIPTION or SETUP gt NETWORK of DVR MODEL NAME D16HS SOFTWARE VERSION Ver 3 9 3 20131206 STORAGE SIZE 435 GB NETWORK TYPE DHCP IP ADDRESS 172 16 2 41 MAC ADDRESS 00 02 69 FF FO 9E DDNS STATUS DDNS OFF UNIT NAME HYBRID REMOTE CONTROLLER ID 0 3 Run the network client software speco technologies SPECO Multi Client Ver 3 1 2 5 103 Site Addition E Site Info Site name Site address Port number 5445 ID Password Input Site Name Site Address IP address Port Number and Password on the connect window e Site Name Input a name that properly describes a site e IP Address Input IP address e Port Number Default Port Number is 5445 e ID Input ID of DVR Default ID is admin e Password Input network password of DVR Default Password is 1111 z lt Select a site by checking the box and Press E button to connect to the site 104 APPENDIX Network Connection Internet and DDNS Dynamic Domain Name System DDNS allows a domain name to be constantly synchronized with a dynamic IP address A current dynamic IP address is being associated with a static domain name 4 lt a ins Ic cE 1 Goto SETUP gt NETWORK gt DDNS and set the DDNS SERVER to ON ENABLE DDNS ON HOST NAME hostname SUBMIT UPDATE OFF Z ezDDNS OFF EY APPLY CLOSE If you set ezDDNS to ON the
58. ect event to archive ae C StoragelLogl E Event search Size y MAX 100MB H Record fel Disk A Display Event Language Startup About Shutdown e setup Change Sensor in Alarm out 22 Motion SN Camera loss aA Network loss ad Record Event list a E E E E E E ERA Ear General First 2011 04 26 Ely 12 00 00 AM Ps lest 20710428 By T4BS4PM E Event search a Record C StoragelLog E Disk W Display Language P About Address Event Date Time 74 7 6 3 Record Record Setup You can set the recording conditions as the following Always Event or Auto record And you can also select target DVR DVRs and channel channels When you set the recording condition to event you can set event for motion or alarm with duration Record Condition General 3 Always Event F Auto record g Event B Event search l Record m Disk Channel Display Ste Dan site Language About JO CH Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Event Motion Alarm Duration itl Record Local Storage Setup You can select the local disk to record and the amount of disk space you want to allow the program to use for recording You can also select the option to overwrite data or stop recording when the maximum amount of disk space is full General Disk Space ca Event ES Event search a Record m Disk Free space 398 GB W Display Language About Replace oldest
59. ed 8 Use the mouse scroll to digitally zoom in and out from a single channel display 7 8 5 2 Playback of Recorded Video on Remote DVR 1 Click mo REMOTE PLAYBACK And then Playback Window will be displayed over the Live Window speco technologies SPECO Multi Client Ver 3 1 3 8 SMTWIT EE ES 4 5 S 7 3 9410 n 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 Select the site to connect from the directory window 92 3 Click CONNECT And then Green bar displays on Search calendar and timeline scale window SMTWHTI eFE S amp S 12 3 4 65 7 38 940 OM 21 22 23 24 25 26 27 28 29 30 31 7 8 6 AVI Backup during Playback You can back up the recorded videos in AVI format during playback 1 Double click the target channel to backup 2 Select the beginning time by using the search calendar and timeline scale bar E 2 IC A 6 amp 9G 1 44 12 13 14 1 19 49 20 21 22 23 24d 25 26 27 28 29 30 93 E 3 Click ES EZCOPY START button on the timeline scale to select the beginning point of the backup 4 Click EZCOPY END button on the timeline scale to select the ending point of the backup Then the selected starting point and the ending point on the timeline scale bar will be marked in green Backup Select Channels CH 1 CH 2 CH 3 CH 4 7 AN setting StartTime W 17 18 End Time 01 19 43 File Path CA Storage Backup F
60. ex window after disconnect a site GA NET FINDER Select the site from the index window and click this icon to modify the information of specific site CONNECT Click this icon to connect the selected site sites DISCONNECT Click this icon to disconnect the selected site sites 71 ou Bp Click this icon to setup configuration of SpecoTech Multi Client EZCopy Start video in AVI format Click this icon to set the ending time for backup of the recorded video Click this icon to backup the recorded video in AVI format A caps To select the numbers of DVR DVRs 1 DVR 4 DVRs 9 DVRs 16 DVRs on main display screen To select the numbers of display channel channels Single quad 9 ailal channels and 16 channels of highlighted site To select the channel to playback The calendar shows dates with recorded video in color 24 25 26 27 28 29 30 Al To display the recorded data of selected channel or all channels on a s sE time line scale To change a timeline scale from 24 hours to 60 minutes The timeline shows recorded data in color on the bar You can adjust the timeline scale and move it to the time you wish to playback Then click the play icon to display the recorded video Thumbnail search over the network List the thumbnail 24images from 00 00 to 23 00 Select one of 24 images every 150sec for an hour EZ Search Then play the tile Click the PREVIOUS button to go the
61. hannel order 33 4 3 Setup RECORD Mode In the SETUP menu select the RECORD tab Then the RECORD menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control O E SITE RESOLUTION FRAME RATE QUALITY RECORDING MODE SENSOR RECORDING PRE RECORD 1 MINUTE S POST EVENT RECORD 10 SECOND S x AUDIO OFF SCHEDULE a RECORD APPLY Figure 4 3 1 RECORD Setup Screen CANCEL Table 4 3 1 Menu Items in RECORD Setup Screen Menu Item Description SITE Select a channel for applying the following settings using the mouse or the remote control To change the values of all channels take the following steps Select the button to change the values of all channels RESOLUTION FRAME RATE RECORDING PRE RECORD pag id ai LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S LEVEL 5 H CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1 MIN S 10 SEC S CONTINUOUS 1
62. he channel location To swap the channel drag a channel to another channel 7 Digital Zoom In Out Double tap on the desired channel to view in 1channel mode Then use the iPhone zoom feature using two fingers to pinch the screen to zoom in or out on the video image User can also move the zoomed image around by touching the desired spot and dragging the zoom image 9 1 2 PTZ Control To control the PTZ functions of the camera tap the menu button Then PTZ menu icons will display Using the PTZ icon on the screen control PTZF control 99 lt D16H5 LIVE 09 10 14 00 47 28 9 1 3 Playback 1 Select Mode as Playback and click CONNECT button Then select Date Time and click PLAY button Device D16HS Edit Diens Select Date 4 Time mb Connect ro Today 4 48 PM mb Play Ste D16HS IPVONS demods didn specoidns mal 2 The app will display the selected channel s Double tap the channel screen to switch 1 channel display to 4 8 10 16 channels split display depending on the DVR lt Select Date amp Time PLAYBACK 03 05 14 17 31 06 3 Tap the menu button Then Playback menu icons will display lt Select Date amp Time PLAYBACK 03 05 14 17 31 20 1 18 fo o SI IM Dz 100 9 2 App Viewer for Android Phone 1 Enter the Android Play Store AN Na 2 Search Speco Player in the Android Market and install the Speco Player app Notice SPECO Player is
63. he mouse to return to the previous menu AUFAN AA CIO 024 Ma NX WBE A Z 2 MENA N Vien 42 7 C48 T Nean A PY AA EANAN LER Y GTA EEGEN icc H Coe E A ES Mo MI TT IR LE EENEN e if or 4 4 4 Motion Zone Grid Screen 41 4 5 Setup DISPLAY Mode In the SETUP menu select the DISPLAY tab Then the DISPLAY menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control To return to the previous setup menu screen press the ESC button E DISPI LAY CONTE RAST Mi AIN M ONITOR S SE EQUENCE NC E DWE EL 7 TIN 113 ME SEQUE i SITE E COLOR TUNING DO UTI PU U IT Figure 4 5 DISPLAY Setup Screen Table 4 5 Menu Items in DISPLAY Setup Screen Item OSD Description Enable disable on screen display CHANNEL NAME VIDEO LOSS STATUS BAR Lae ICON OSD CONTRAST Set the transparency level of the On Screen Display OSD 50 100 MAIN MONITOR SEQUENCE Enable disable sequential display of video in full screen mode SEQUENCE CHANNEL SEQUENCE Set the dwell time of each single channel display in sequential display DWELL TIME mode 3 60seconds SITE Select a channel to apply the name and covert settings change using the mouse or the remote control Select a channel to apply the following settings using the mouse NAME Set the channel name Press the right square button and set the channel
64. host name is automatically generated and registered 2 Goto SETUP gt NETWORK gt DDNS gt HOST NAME Manually enter a domain name using the virtual keyboard and click ENTER button HOST NAME hostname E E JE RARA CAPS la es dol 8 E E JA a A es _ ENTER 105 When a manual host name is completed Go to SETUP gt NETWORK gt DDNS gt SUBMIT UPDATE and select ON to submit the settings on the SPECO DDNS Once the setting is completed the DDNS address will be http hostname ddns specoddns net For example if you enter the host name as D16HS then the address will be When DDNS setting is done click the APPLY button Otherwise DDNS setting will not be applied When you exit SETUP menu DDNS NOTIFIY window will pop up DDNS registration status can be checked from SYSTEM INFORMATION or SETUP gt SYSTEM gt DESCRIPTION gt DDNS STATUS MODEL NAME D16HS SOFTWARE VERSION Ver 3 9 3 20131206 STORAGE SIZE 435 GB NETWORK TYPE DHCP IP ADDRESS 172 16 2 41 MAC ADDRESS 00 02 69 FF FO 9E DDNS STATUS DDNS OFF UNIT NAME HYBRID REMOTE CONTROLLER ID 0 Check the NETWORK PORT Default 5445 WEB PORT Default 80 and the IP Address of the DVR from SETUP gt NETWORK EEE 0 0 0 T E T 8 Port forward the NETWORK PORT Default 5445 and WEB PORT Default 80 of the private IP Address of the DVR on the network router Please refer to the user manual and guide for the detailed steps for port forward
65. ile format ai 6 You can also set the beginning time and ending time on this window After selecting a channel for backup click the OK button The backup will begin Backup select Channels CH 1 CH 2 CH 3 CH 4 Start Time 01 17 18 End Time 01 19 43 File Path CiStoragelBackupi File format Ayl OK Cancel 94 7 AVI video data is recorded as set in AVI Backup window AVI format video can be played back by using Window Media Player or other media player that is compatible with AVI format video CH01 01_17_18 95 8 Network Access Using the Web Browser Viewer The DVR provides a live remote monitoring feature by web browser viewer NOTE Web Brower is only available for Internet Explorer 1 Check the IP address of the DVR from SETUP gt SYSTEM gt DESCRIPTION gt IP ADDRESS or 2 Input the IP address or Domain name address that you pre registered e http 172 16 2 38 web_viewer html Web Client 3 Click this bar Then the dialog box is displayed This webpage wants to run the following add on CNC_Ctrl Module from Not Available What s the risk This website wants to install the following add on speco_control verl 6 3 7 from Speco Technologies What s the risk A Click Install to download and install the ActiveX control 9 User Account Control A Do you want to allow the following program to make changes to this computer E i Program n
66. ing for specific router model 6 Run the network client software Site Addition x SPECO Multi Client Site Info Wer 3 1 7 5 I Sitename Site address Port number 5445 ID Password aK canes 7 Input Site Name Site Address IP address Port No and Password on the connect window e Site Name Input a name that properly describes a site e IP Address Domain name or Public IP address of a router that DVR is connected e Port Number Default Port Number is 5445 e ID Input ID of DVR Default ID is admin e Password Input network password of DVR Default Password is 1111 E E 8 And select the OK button Then press HA button after checking the left check box APPENDIX E SATA CONNECTION Please read the following instructions before using the E SATA port Failure to do so may cause serious damage to the recorded video SPECO is not responsible for data loss caused by improper usage e Use ONLY a new HDD or a HDD that is approved for the unit e Turn off the DVR before plugging the E SATA HDD e DO NOT disconnect the E SATA port while the DVR power is on e The purpose of the E SATA port is to extend recording capacity e Once connected DO NOT Remove or disconnect the E SATA port from the DVR e The E SATA port is does not support the hot swappable function 107
67. io streaming lf these ports are not opened properly you can t access the DVR beyond a router o For live playback streaming for commands for remote backup Open the port number on NETWORK gt NETWORK PORT menu The default port number is 5445 o For bi directional audio Open the port number on NETWORK AUDIO PORT The default port number is NETWORK PORT number 1 o For web viewer downloading and remote firmware upgrading Open the port number on NETWORK gt WEB PORT menu The default port number is 80 4 6 4 Network Stream User can set the RESOLUTION FRAME RATE and the QUALITY for the network stream D16HS Up to 480 fps CIF for 16 channels D8HS Up to 240 fps CIF for 8 channels lt Note gt Individual Channels can be set with different RESOLUTION FRAME RATE and QUALITY RESOLUTION FRAME RATE LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H LEVEL 5 H L USE MOBILE OK CANCEL Figure 4 6 4 NETWORK Setup Screen Network Stream lt TIP gt USE MOBILE When this function is enabled the frame rate is limited to 15fps CIF and the video quality is limited to LEVEL 2 for better remote viewing on the mobile phone 46 4 7 Setup USER MANAGEMENT Mode In the SETUP menu select the USER MANAGEMENT tab Then the USER MANAGEMENT menu is displayed as pictured below Navigate through the menu items or change the settings usi
68. ion Temperature 41F 104F 41F 104F During storage 14F 122F During storage 14F 122F Weight Unit Weight Gross weight Approximately 11 lbs Approximately 12 lbs Unit Dimension W x H x D 15 W x 2 83 H x 13 4 D 15 W x 2 83 H x 13 4 D Please note that specifications and unit exterior designs are subject to change without notification Table of Contents T 2 MaN CUCU SS osue a a saben care ei r E bat 10 HBO IM TOCO Sinama dad O aaa a ica tela sina tinea alee has chitanleguiea dian aaa 11 2 1 Initial Boot up and Basic TIME Setup rsin as 11 2 2 Setting up Daylight Savings iMac ais 12 2 3 Setting NTP Network Time Protoco l oocoooccoccconconcococonoccncononononnnnononnnnononnonanonnonanenanonos 13 P A e al E E EAA A E E E A A T E E AA EA AS 16 FROME ANG Rear Panel S zenro a A due Geabaeadiaearnwedeaay Medea 21 Fo FO acl 11g 1 I anea AAA ee eee 21 3 2 Rear Panel Connector S iia A A AA 22 Dae REMO CONTO ia ias 23 SOWING UD THE DVR resene 24 AUS cun MaM Eve Scene seda 24 4 1 Setup IP CAMERA ra A AAA A 25 A A E E ia sataeuilannd 26 4 1 2 ONVIF SETUP MGW dt its 27 a SA naa a eaeeautan aaa cits aticmigeate Geass 29 AL CUNO SY O ME Mi A A A 29 4 37 o eUD RECORD MOE dai od 34 4 4 Setup DEVICE MOGG ii A nada 36 AAA Data Detetmentosa nun estadio cas 37 4 4 2 Keyboard Controller amp PTZ Setup ooccccccccccociccncccnoonconcncnnononcnnnnnnnnoncnonnonnnnnnnononnnnnnonanennnennos 3
69. ion sensitivity from 1 to 9 9 Highest sensitivity 1 Lowest sensitivity KEY TONE Enable disable key tone from front panel usage REMOTE CONTROL ID Set the remote control ID 1 Select ID 36 2 Input the remote control ID number 3 An icon will indicate on the Live Screen if the remote control ID is synchronized The options are from 0 to 99 SENSOR Select the type of each sensor Option is Off Normal Open or Normal Close VIDEO INPUT 960H Resolution to support non standard function TRIMMING ON Non Standard OFF Default 4 4 1 Digital Deterrent Trigger audio message via motion detection or sensor IMPORT FROM USB EXPORT TO USB RECORD SCHEDULE Figure 4 4 1 Digital Deterrent setup screen Table 4 4 1 Item for Digital Deterrent Setup Screen Item Description IMPORT FROM USB Import up to 8 sound files from USB EXPORT TO USB Export the sound file to USB RECORD Select a channel and set up the date and the duration select START to export audio to Digital Deterrent Select the play button to hear message after export CHANNEL cH 1 FROM 11 TO 11 06 2012 15 08 06 DURATION 10 SECOND S FILE NAME sound 1 START CLOSE 3 SCHEDULE Schedule the sound file considering the expected situation CHANNEL 1 1a NONE DEFAULT SOUND 1 SOUND 2 SOUND _3 SOUND 4 SOUND 5 SOUND 6 SOUND 7 SOUND 8 CLEAR 2 2 2 3 ja 3 a e je 7 7
70. lowing window will be displayed as below Site Addition O Site Info Site name Site address Port number 5445 ID Password cancel Site Name Input a name that properly describes a site IP Address Input IP address Public IP address of a router that DVR is connected or Domain name Port Number Default Port Number is 5445 ID Input ID of DVR Default ID is admin Password Input network password of DVR Default Password is 1111 2 Click OK button And then the registered site is added on the directory window 7 8 1 Select 1 2 Deleting a Site the site sites to delete from the directory window 2 Click GE SITE DELETE button And then the selected site sites is are deleted 8 7 8 1 3 Modify of Sites 1 Select the site sites to modify from the directory window 2 Click E NET FINDER button And then the following window will be displayed as below Net Finder X Name Address i Address Port No Mac Model D16HS 172 16 2 49 3 Click MODIFY button And then the modified information is displayed as below Site Modify Site Info Site name D16H8S gt Site address 17216249 Port number 5445 ID admin Password TT Channels Channels Display Device Channel name 88 7 8 2 Connect and Disconnect 7 8 2 1 Connect 1 Select site sites to connect from the directory window 2 Click CONNECT button and then site
71. me or select one from the existing folders list Click Next to continue avast Free Antivirus CMs OTS A4C 3 Filter DWR lt Back Cancel 4 The installation status screen is displayed 5 After the installation is completed SpecoTech Multi Client icon displays on the desktop screen Specolech Multi Clrent 68 7 4 Live Window When installation is completed double click the SpecoTech Multi Client icon on your desktop to start the program 7 4 1 Main User Interface speco technologies SPECO Multi Client Ver 3 1 3 1 7 4 2 Control Buttons Button Description CCOO Click this icon to run a playback window to search and play videos that are recorded in the local PC LOCAL PLAYBACK Click this icon to run a playback window to search and play videos that are recorded in the remote DVR REMOTE PLAYBACK 3 THUMBNAIL REFRESH Click this icon to refresh and renew thumbnail image of the connected sites SITE MANAGEMENT SITE ADDITION Click this icon to open Site Addition window E SITE DELETE Click this icon to delete site from the index window after disconnect a site 54 NET FINDER Select the site from the index window and click this icon to modify the information of specific site Click this icon to connect the selected site sites CONNECT 69 oD Click this icon to disconnect the selected site sites DISCONNECT MA Click this icon to setup configuration of MULTI C
72. mera to set system and time settings SPECO WEB SETUP SYSTEM RECORD DEVICE DISPLAY NETWORK USER MANAGEMENT STORAGE UPGRADE INFORMATION CHANNEL PROTOCOL IP PORT WEB PORT ID PASSWORD e CHANNEL Select the Channel to setup an IP Camera o Protocol Select the Brand of the IP Camera o IP Enter the IP Address of the desired Camera o Port Enter the Camera stream Port Number default 554 o Web Port Enter the Camera Web Port Number default 80 o ID Enter the User ID for access to the IP Camera o PASSWORD Enter the Password for the associated ID 78 7 7 2 System Select System to set system and time settings CARES Slee SEDER OS Le See DATE OSSPLAY FORMAT TAE DISPLAY FORMAT TAE ZOME DAYLIGHT SATF SET DATE amp THE CUENT ACCESS NTF TUE PUMA ENTP SEANTA SSCOMOASY SHTI Saver TIME DOME COMME TOM MODE CONNECTION PERICO SENO EMAL SETUP SAVER TYPE WAL SPER WAIL PCLT SEUA OPTION AS FAA ASG TEST OOOO MAL FAR O MAL TEST APPLY HAL ATT TAS LIMIT PL A A SST RESTAT STA a OTI TICA DA AT a TS im ID Te AT AD go CTO HOD ALT FULL Video CLS SETIS Fria PALA Ee HEALTH CA Sa ST SALT SALTO AA Lf in il i i ti PARC ABC SLAVE MITON Cte WiDeO LOSS RIO Tee AAT Ae RODADO SECTORS i HIC ALMOST FULL HOFI G AJEA AE LA LSP A AAA EATE HOO FAJA Fi e DATE DISPLAY FORMAT Select the date display format DATE DISPLAY FORMAT MM DD YYYY TIME DI
73. ng the mouse or the remote control m USER MANAGEMENT AUTHORITY SETUP USER NAME SETUP PASSWORD SETUP PLAYBACK AUTHORITY REMOTE PLAYBACK TIMEOUT DISABLE APPLY CANCEL Figure 4 7 USER MANAGEMENT Setup Screen Table 4 7 Menu Items in USER MANAGEMENT Setup Screen Item Description AUTHORITY Only the Admin will have access to the menu SETUP PASSWORD CHECK Select the Checkbox to enable the functions or leave the Checkbox blank to disable the functions SETUP Enable Disable of access to Setup PB Enable Disable of access to Playback PTZ Enable Disable of access to PTZ Control REC OFF Enable Disable of manual Record NETWORK Enable Disable of access to Network selected Checkbox The DVR will ask for a password when the given function is selected for all users Blank Checkbox The DVR will not ask for a password when the given function is selected for all users PASSWORD CHECK Y oK CANCEL 47 ADMIN USER1 USER2 USER3 Selected Checkbox The user can access the function Blank Checkbox The user can not access the function USER NAME Change the name of USER1 USER2 and USER3 SETUP e Click ENTER after naming PASSWORD Options are ADMIN USER1 USER2 and USER3 SETUP Select USER PASSWORD using the mouse or the remote control and press SEL button Select user type and enter the current password And enter a new password enter the same
74. ns from 9 to 16 is used as function keys on PTZ control mode To escape out of PTZ mode press the ESC button copy rates a Screenshot on Live View and Goes into Backup during Playback sea Enables the sequence mode onte MODE Toggles between the available display modes 1x 22 33 4d POWER Wilintate system town gt SEARCH mode Skips 1min ahead on playback and 1 frame ahead on pause gt LIVE mode Moves Right SEARCH mode Control the play speed Fast Forward KM SEARCH mode Slip Imin back on playback and 1 frame back on pause SEARCH mode Skips 1min back on playback and 1 frame back on pause E LIVE mode Moves Left SEARCH mode Select the play speed Rewind LIVE mode Select Center SEARCH mode Play amp Pause 21 3 2 Rear Panel Connectors 6080009005000 e Do not power this system on before all the connections are attached Make sure all the connections are properly secured Faulty connection may result in the system being damaged D8HS Figure 3 2 1 Connectors Ground Use for ground port VIDEO IN Video input port For Analog 960H cameras VIDEO OUT MAIN Composite Video Output SPOT Spot Monitor AUDIO IN amp OUT Four connectors for audio input and one connector for audio output HDMI HDMI output port Connectors to the HDMI Monitor VGA VGA Video Graphics Array output port Connects to the PC VGA monitor E SATA External SATA port for extension storage
75. ny heavy or sharp objects on the unit e Do not place on uneven surface e Do not expose to shock or vibration e Do not move the unit when the unit is powered on e Do not block and allow dust to accumulate in the air vents e Do not restrict airflow of the unit doing so can damage the unit e Only qualified and experienced personnel should perform installation and servicing e Turn off the power of the HS when connecting Cameras Audio or Sensor Cables e The manufacturer is not responsible for any damage caused by improper use of the product or failure to follow instructions for the product e The manufacturer is not responsible for any problems caused by or resulting from the user physically opening the HS for examination or attempting to repair the unit Product Components Please make sure the following components are included as specified below DVR Unit Desktop D8HS D16HS Remote Control Battery 1 5V AAA x2 Quick Setup Guide Quick User Guide USB Mouse Software amp Manual CD Rack mount x 2 amp Screw x 6 Adaptor DC12V 5A amp AC Power cable 110V or 220V Audio Cable vie eee digegecece QU Uhr fe ee Quick User Guide HS 8 16 Channel IP amp Analog 960H Hybrid OVR Dewees Mass Ofer DSHS o AA e on ees ee be te EDO A Specifications MODEL D8HS D16HS Audio Input Local Input RCA E EI Remote Input from IP Camera Audio Audio
76. password again to confirm and select OK Then the message PASSWORD CHANGED is displayed The factory default password is 1111 It is highly recommended to assign a new password to protect the system AUTHORITY Set authority level of playback on each user OF PLAYBACK Checked box authorized to playback Blank check box no authority OK CANCEL REMOTE Disconnect the remote playback after the specific time Disable 5min 10min 15 min PLAYBACK 30min 60min TIMEOUT 4 8 Setup STORAGE Mode In the SETUP menu select the STORAGE tab Then the STORAGE menu is displayed as pictured below Navigate through the menu items or change the settings using the mouse or the remote control JOY STORAGE OVERWRITE DISK FORMAT DISK INFO RECORDING LIMIT RECORDING LIMIT DAYS SEEE 4 m E CANCEL Figure 4 8 STORAGE Setup Screen 48 Table 4 8 Menu Items in STORAGE Setup Screen Item Description OVERWRITE When enabled the DVR will continue recording and overwrite the oldest existing recorded data once the hard drive is full When disabled recording will stop once the hard drive is full DISK FORMAT You will have an option of YES or NO for formatting the Hard Drive A After formatting HDD the DVR will reboot Caution It is recommended to archive any data that you may need in the future before formatting the hard drive
77. sites displays display as connected 7 8 2 2 Disconnect 1 Select site sites to disconnect from the directory window 2 Click DISCONNECT button and then selected site sites disconnected 7 8 3 Still image Capture During Live 1 Double click a channel to capture from the display screen Otherwise all channels will be captured 2 Click AE ure button And then a Capture window will be displayed as below Capture Save Path s martin Documents Speco Capture D16HS File name 2014 07 10 222353 File Format BITMAP BM P 89 3 Set Save Path File Name and File Format And then click OK button 4 Still image is saved as set in Capture window 7 8 4 Recording Video on Local PC During Live 1 Click ES SETUP button And then a setup window will be displayed as below 2 Select Record and set the values General Record Condition Event Event search da E Event EF Disk Motion Duration Display About Channel Ste Ds CH Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 9 Always Event Auto record 3 Select Disk and set the values General Event Disk Space CA E Event search T Record Disk Info E Total space 465 GB Display p ahead Free space 398 GB Disk full Replace oldestfiles Stop recording 4 Click RECORD ON button And the color of button is changed 5 Live video dat
78. tible with AVI format video 1 Please install the HS copies HDPlayer folder on USB flash drive with the video en USB DISK F 4 Computer amp Local Disk C Ga Local Disk D e USB DISK F J 2 items k 65 2 Otherwise the video and time stamp over video can t be properly played back and displayed on Window Media Player a x wy 2010 10 04 44 7 A 1 f 7 y ais aT o del gt New A 77 on 188 Timestamp On AVI The subtitle is embedded to the video clip file The subtitle is embedded to the AVI file 6 5 2 NSF Format NSF format NSF format video can be played back using the Play HDplayer that the DVR copies to DvrPlayer folder on USB flash drive with video Use the mouse scroll to use digital zoom in and out feature 2011 10 10 04 44 44 2011 04 27 01 42 44 DLS Gs Gu iL ur A x4 66 7 Network Access Using the Multi Sites Network Viewer 7 1 Overview The SpecoTech Multi Client is a multiple site monitoring client software with video audio and alarm signals from the DVRs over networks The SpecoTech Multi Client does not limit the number of DVR units to register The program displays up to 16 DVRs and supports dual monitors On the program user may control PTZ cameras on the DVRs By attaching a microphone and speaker system to devices on site the user may make bi directional audio communication over the network 7 2 PC Requirements Minimum
79. u screen search window or exit from the Menu 6 Back Up 6 1 Still Image Backup onto USB Flash Drive Still images can be captured and archived onto a USB flash drive or an USB external hard drive in live mode or while playing back recorded video 1 Select a specific channel which wants to backup on live screen 2 When you press SNAPSHOT button on Quick operation window the media selection window screen will display SEARCH PLEASE SELECT MEDIA TYPE USB DRIVE SETUP DISPLAY SNAPSHOT SUPER EZ COPY ENABLE MANUAL RECORD ADVANCED MENU gt Re 3 Once you press START button the system will capture a still image and archive onto a USB flash drive NOTICE USB Flash Drive must be in FAT32 file format 6 2 Video Backup onto USB Flash Drive during playback Video can be captured and archived onto the USB flash drive or a hard drive while playing back the recorded video In playback mode press the BACKUP button to launch the backup function 1 When you press BACKUP button on the selected channel or all channels the DVR will ask whether to archive a Still Image a NSF or AVI and select the proper media type PLEASE SELECT ARCHIVE MEDIA TYPE O STILL IMAGE NSF PROPRIETARY FORMAT AVI INTEGRATED SUBTITLE O AVI SEPARATED SUBTITLE MAC COMPATIBLE lt PREV NEXT gt CLOSE PLEASE SELECT MEDIA TYPE USB DRIVE 2 Select USB DRIVE Flash Drive to back up less than an hour select USB H

Speco D8HS, D16HS

Contents

Download Pdf Manuals

Related Search

Related Contents