X7 Access Control
Contents
1. Delete a User Delete All Users 2 Access Control Management 2 1 Set Change Eight Passwords for Opening the Door 2 2 Configure Unlocking Duration 2 3 Configure Authentication Mode 2 4 Configure Concealed Mode 2 5 Configure Door Sensor Mode 2 6 Configure Alarm Configure Alarm setting Configure Error Operation Triggered Alarm Configure Tamper Alarm Configure Alarm Delay for the Door Status Sensor Operation Instructions 1 User Management 1 1 Administrator Operations To ensure data security of the device you can operate the device only after the administrator password is authenticated Administrator Authentication 1 Press 2 Press 3 Enter the administrator The indicator is off and You can authenticate the eee Bren makes a long beep password p 1234 5 Exit ae eta Press or do not operate 4 The TEAS is sine successful ene whin eg The indicator turns green Ndote The initial administrator password is 1234 You are advised to change the initial password at the beginning Change Administrator Password 1 The administrator a n ote 3 Enter a new password is authenticated 7 password g administrator password Failed The indicator turns re YES and makes three 6 E 5 S ded a Exit Succeeded2. The device automatically The indicator turns prairie a exits the process when the green and makes a long EROT RE EAR operation is completed beep g j Note Four digit passwords are automatically verified For passwords with less than four digits press to enter the verification process Open the Door by Entering the Administrator Password 1 The administrator password is authenticated 2 Press 0 The indicator turns green and makes a long beep 3 Press 0 The indicator turns green and makes a long beep Note This function can be used to open the door 5 Exit The device automatically exits the process when the operation is completed 4 The door is opened The indicator turns green and makes a long beep Administrator Password Is Forgotten If the administrator password is forgotten you can press the tamper switch three times to reset the password to the initial administrator password 30 to 60 seconds after the device is disassembled from the wall or door There is a long beep 30 seconds after the device is disassembled from the wall or door 1 2 Add Users Register the fingerprint or card of a user or register cards in batches Add Users 1 The administrator password is authenticated 2 Press 1 The indicator turns green and makes a long beep 3 Register fingerprints or cards
3. Press fingers three times to get a fingerprint or swipe the card once Note 1 In the registration process the user ID increases automatically The device automatically enters the process of registering the next user when a user is successfully registered 2 The registration process fails if the fingerprint is of poor quality or the fingerprint or the card has been registered After the device indicator turns Failed The indicator turns a and makes three beeps Yes 5 Exit Press to exit 4 Adding Users is successful The indicator turns green and makes a long beep 6 green you can register the user again Registered users must not be registered again Register Cards in Batches 1 The administrator password is authenticated 2 Press 6 Registering Cards in Batches only 3 Swipe the first card once Failed The indicator turns red and makes three beeps Yes 6 Exit The device automatically exits the process when the operation is completed 5 Cards are successfully registered in batches YES cards m 4 Enter the total number of Note 1 In the process of entering the total number of cards three digit numbers are automatically verified For numbers with less than three digits press to enter the verification process Pr
4. the operation is completed 5 The configuration is successful The indicator turns green and makes a long beep then turns red and makes a long beep again 4 Configure the concealed mode 0 enable 1 disable Note 1 An indicator blinks to indicate the status of this function when users are authenticating their cards or fingerprints 2 The indicator turns red and makes a long beep in fifth step indicates system exits when setting successfully 2 5 Configure Door Sensor Mode The door sensor switch includes three modes NONE The door sensor switch is not used NO The lock is open as long as the door is open NC The lock is closed after the door is closed 1 The administrator password is authenticated 2 Press 0 The indicator turns green and makes a long beep 3 Press5 The indicator turns green and makes a long beep 6 Exit The device automatically exits the process when the operation is completed 5 The configuration is successful The indicator turns green and makes a long beep then turns red and makes a long beep again 4 Configure the door sensor mode 0 enable 1 disable 2 without door status sensor Note 1 The door sensor mode configured here is used as the basis for the door sensor alarm 2 The indicato
5. Passwords for Opening the Door 1 The administrator password is authenticated 2 Press 3 The indicator turns green and makes a long beep The indi and makes three beeps 3 Enter the password ID of the to be changed password The password ID ranges from 1 to 8 Failed cator turns red 6 The password is changed The device indicator turns green and the device makes a long beep 5 Enter the new password again for authentication YES 4 Enter a new password The password consists of four digits 7 Exit Press or to exit Note 1 The initial eight passwords for opening the door is empty 2 If a password is successfully changed enter the password ID of the to be changed password to change the next password 2 2 Configure Unlocking Duration 1 The administrator password is authenticated 2 Press 4 The indicator turns green and makes a long beep 3 Enter the unlocking duration range 0 to 255 Note 1 Three digit values are automatically verified For values with less than three digits press to enter the verification process Values greater than 254 are considered invalid 5 Exit The device automatically exits the process when the operation is completed 4 The unlocking duration i
6. Sensor DSen Delay Door Sensor Delay indicates the delay in checking the door sensor after the door is open If door sensor state is inconsistent with the normal state set by the door sensor switch an alarm will be generated and this period of time is regarded as the door sensor delay 2 Press 0 3 Press 4 The indicator turns green The indicator turns green and makes a long beep and makes a long beep 1 The administrator password is authenticated 5 The configuration is 6 Exit successful The device automatically exits the process when the operation is completed m 4 Configure the alarm The indicator turns green delay and makes a long beep range 1 to 254 then turns red and makes a long beep again Note 1 Three digit values are automatically verified For values with less than 14 three digits press to enter the verification process Values greater than 254 are considered invalid 2 The indicator turns red and makes a long beep in fifth step indicates system exits when setting successfully 15
7. ZK Tzca Advanced Biometric and RFID Solutions X7 Access Control System User Manual Produced by ZKTeco Inc 1 Equipment Installation Wall mount installation 1 Remove the screw on the bottom of device 3 Fix the back cover on the wall according to the mounting paper 4 Fix the device to the back 5 Fix the screw cover 2 Structure and Function Access Control System Function 1 If a registered user verified the device will export the signal to unlock the door 2 Door sensor will detect the on off state If the door is unexpected opened or improperly closed the alarm signal digital value will be triggered 3 If the device being illegally removed the device will export alarm signal 4 External exit button is supported it is convenient to open the door inside 5 External bell is supported 3 Lock Connection N Warning No operation when power on 1 The system supports NO LOCK and NC LOCK For example the NO LOCK normally open at power on is connected with NO terminal and the NC LOCK is connected with NC terminal 2 When the Electrical Lock is connected to the Access Control System you need to parallel one FR107 diode equipped in the package to prevent the self inductance EMF affect the system do not reverse the polarities I Share power with the lock re Device share power with the lock ULOCK 12V I ILOCK gt 1A And the lock is near to the d
8. ess to reenter the total number of cards 2 You must clear all the registered users before registering cards in batches IDs of to be registered cards must be consecutive numbers 1 3 User Authentication Authenticate Users Fingerprints Cards Passwords After the device is powered on it enters the authentication state for users to unlock the door 2 Press fingerprints swipe 1 The device is in the cards or enter passwords Yes 3 The authentication is authentication state Press after entering a A successful password Failed The indicator turns red and makes three beeps Ndote Press after entering a password for authentication The door opens if the entered password is identical with one of the eight passwords for opening the door The initial eight passwords for opening the door are empty To change passwords for opening the door please refer to 2 1 Set Change Eight Passwords for Opening the Door 1 4 Delete Users Delete a user whose fingerprint or card is registered or delete all users Delete a User 1 The administrator 2 Press2 3 Enter a user ID press the A z aathenticated The indicator turns green fingerprint or swipe the p and makes a long beep card The indicator turns red Failed and makes three beeps ne 5 The user is deleted YES Exit indi Th dicat
9. evice GND ON BUT Device does not share power GND v with the lock SEN NC SEN A ULOCK 12V I ILOCK lt 1A E zl j X01 B ULOCK 12V N u er At C The lock is far apart from the yL device IQ T device output current ULOCK lock voltage ILOCK lock current 4 Connected with Other Parts Exe Button ead bed amp Door Sensor Alarm Power lt i r i a Alarm Power Alarm Voltage output lt DC 12V for Alarm 5 Connect with Power DC12V Input DC 12V 500mA 50mA standby Positive is connected with 12V negative is connected with GND do not reverse the polarities Instructions Recommended Procedure Step 1 Install the device and power on Step 2 After the administrator password is authenticated and changed register users fingerprints cards or passwords Step 3 Configure access control parameters including modifying eight passwords for opening the door and configuring the unlocking duration authentication mode stealth mode door status sensor mode and alarm Functions of the Device 1 User Management 1 1 Administrator Operations Administrator Authentication Change Administrator Password Open the Door by the Administrator Password Administrator Password Be Forgotten 2 Add Users Add Users Register Cards in Batches 1 3 User Authentication 1 4 Delete Users
10. or t Press or do not operate 1 ji 4 o ae ane eee 1__ 4 Determine whether the the device within 20 mand makes a tong beep K user is authentic seconds then turns red and makes a long beep again Note 1 In the process of entering user IDs five digit IDs are automatically verified For IDs with less than five digits press to enter the verification process 2 The device automatically enters the process of deleting the next user when a user is deleted 3 The indicator turns red and makes a long beep in fifth step indicates system exits when setting successfully Delete All Users 1 The administrator password is authenticated 2 Press 9 The indicator turns green and makes a long beep 3 Press 9 The indicator turns green and makes a long beep Note 1 Press 9 for automatic confirmation Other values are considered 5 Exit The device automatically exits the process when the operation is completed 4 Deleting All Users is successful The indicator turns green and makes a long beep then turns red and makes a long beep again invalid If an invalid value is entered the device indicator turns red and the device makes a long beep and exits the process 2 The indicator turns red and makes a long beep in fourth step indicates system exits when setting successfully 2 Access Control Management 2 1 Set Change Eight
11. r turns red and makes a long beep in fifth step indicates system exits when setting successfully 12 2 6 Configure Alarm Note If an alarm is triggered the device generates an alarm 30 seconds later the alarm is switched to an alert The alarm can be terminated after the user is authenticated Configure Alarm setting The alarm should be on by default when it is set to be close the Error Operation Triggered Alarm Tamper Alarm the Alarm Delay for the Door Status Sensor will be disabled 1 The administrator Z Press 0 i ee Press password is authenticated The indicator turns green The indicator turns green and makes a long beep and makes a long beep 5 The configuration is 6 Exit successful 4 Configure the alarm The device automatically The indicator turns green setting exits the process when the and makes a long beep 0 enable 1 disable operation is completed then turns red and makes a long beep again Note The indicator turns red and makes a long beep in fifth step indicates system exits when setting successfully Configure Error Operation Triggered Alarm If this function is enabled alarms are generated if an administrator fails the authentication upon three attempts The administrator authentication is not allowed within 20 seconds after an alarm is generated 1 The administra
12. s modified The indicator turns green and makes a long beep then turns red and makes a long beep again 10 2 The indicator turns red and makes a long beep in fourth step indicates system exits when setting successfully 2 3 Configure Authentication Mode 1 The administrator password is authenticated 2 Press5 The indicator turns green and makes a long beep 3 Enter the authentication mode 5 Exit The device automatically exits the process when the operation is completed 4 The configuration is successful The indicator turns green and makes a long beep then turns red and makes a long beep again Note 1 The indicator turns red and makes a long beep in fourth step indicates system exits when setting successfully 2 Details about the authentication mode are as follows Mode 5 number5 RF amp PW RF and password verification Mode 6 number6 FP amp PW fingerprint and password verification 2 4 Configure Concealed Mode If the Concealed mode is enabled the indicator is off when the Concealed mode is in the sleep mode 11 1 The administrator password is authenticated 2 Press 0 The indicator turns green and makes a long beep 3 Press3 The indicator turns green and makes a long beep 6 Exit The device automatically exits the process when
13. tor 2 Press t i a Prese 2 password is authenticated The indicator turns green The indicator turns green and makes a long beep and makes a long beep 5 The configuration is 6 Exit successful 4 Configure the error The device automatically The indicator turns green __ operation triggered alarm exits the process when the and makes a long beep switch operation is completed then turns red and makes a 0 enable 1 disable long beep again Note The indicator turns red and makes a long beep in fifth step indicates 13 system exits when setting successfully Configure Tamper Alarm If this function is enabled alarms are generated once the device disassembled Configure whether to enable the disassembly alarm 1 The administrator password is authenticated 2 Press7 The indicator turns green and makes a long beep 3 Configure whether to enable the tamper alarm 0 enable 1 disable 5 Exit The device automatically exits the process when the operation is completed 4 The configuration is successful The indicator turns green and makes a long beep then turns red and makes a long beep again Note The indicator turns red and makes a long beep in fourth step indicates system exits when setting successfully Configure Alarm Delay for the Door Status
Download Pdf Manuals
Related Search