Voyager 2x Robotic Pool Cleaner Manual
Contents
1. CONTENTS UNPACKING ASSEMBLING THE TRANSPORT TROLLEY ELECTRICAL CONNECTION IMMERSION OF THE ROBOT INITIAL USAGE FUNCTIONING RECOMMENDATIONS CLEANING THE FILTER BAG CLEANING AND STORAGE OF THE ROBOT CHANGING THE PADS INTRODUCTION ASSEMBLY AND INITIAL USAGE Dear Customer Thank you for your confidence in choosing the VOYAGER 2X by ZODIAC This product has been designed manufactured and tested with the utmost care in order to provide you with complete Satisfaction We recommend you read these instructions carefully before using your VOYAGER 2X They contain all the information you need in order to benefit fully from your VOYAGER 2X in complete safety Please contact your retailer a swimming pool professional for any further information He will advise you on the usage and maintenance of your robot He can also supply you with spare parts and is qualified to provide you with after sales service The packaging should contain the following items e the VOYAGER 2X robot e its transport trolley e its control unit e a bag of accessories that includes the user manual and an additional hose weight at minimum e certificate of guarantee e additional foam brushes and a filter bag Check that the appliance has not been damaged during transport bumps broken components etc If you detect the slightest fault don t hesitate to contact your retailer before using your VOYAGER 2X To unpack th2. e components proceed as follows e Withdraw the box on the robot it contains the control unit e Withdraw the top section of the trolley which is located against one side of the box e Remove the robot from the box taking care not to tangle the cable in the trolley e Remove the lower section of the trolley In order to assemble your transport trolley e Loosen the wheel handles located on the lower section of the trolley and remove the screw from the shaft e Fit the upper section of the trolley into the lower section so that the control unit support hook is facing the front of the trolley Diagram 1 e Introduce the screws so as to hold the 2 sections of the trolley together and tighten the wheel handles firmly Diagram 2 ASSEMBLY AND INITIAL USAGE ASSEMBLY AND INITIAL USAGE For your safety and to obtain the best possible performance from your VOYAGER 2X robot proceed as follows e Position the control unit at least 3 5 metres from the edge of the pool avoiding direct exposure of the unit to the sun It can be either placed on the ground or hooked onto the trolley as illustrated in Diagram 6 Diagram 3 e You should only connect the control unit to a plug protected by a safety system with a residual current of 30 mA maximum if in doubt contact an electrician installer Immerse the robot in the pool and draw out any air trapped inside by turning it over if necessary Diagram 4 Squeeze t
3. he foam pads with your hands so as to expel any air and to enable the water to penetrate Diagram 5 It is essential that the appliance goes down of its own accord and lies on the bottom of the pool Spread out the cable over the pool e Connect the robot s cable to the control unit and lock the connector To start the robot select a cycle on the control unit e The Perfect Cycle for a meticulous clean of your pool and the waterline e The Turbo Cycle for a rapid clean cycle if the pool is not very dirty To start your VOYAGER 2X robot press the programme button Perfect or Turbo Diagram 6 The robot starts up after just a few seconds The indicator light for the programme selected comes on If you wish to stop the robot during the cycle press the OFF button Diagram 7 You will have to wait a few seconds before being able to start a new cycle You can change the cleaning cycle at any given time whilst the robot is in ope ration Simply press the button for the other cycle PERFECT or TURBO At the end of the cycle the robot stops The light remains on to indicate that the unit is still live Press the OFF button Diagram 7 Disconnect the power supply cable from the mains plug Disconnect the cable from the control unit and wrap it in large coils Use your cleaner robot as often as possible You will benefit from a pool that is always clean and the filter bag will take longer to clog up The robot is des
4. igned to work in a swimming pool whose water quality is as follows chlorine lt 2 mg l pH between 6 8 and 7 6 temperature between 10 C and 35 C Do not leave your robot in the pool on a permanent basis CLEANING AND MAINTENANCE Make sure that the power supply cable has been disconnected from the mains plug or that the floating cable has been disconnected from the power unit Remove the robot from the water and lay it upside down on the pool side thereby offering access to the filter holder plate located beneath the robot Diagram 8 Undo the 4 hooks that hold the plate in place Remove it whilst holding it upside down so that the dirt remains in the bag Diagram 9 Release the 2 plastic blocking clips to remove the bag Diagram 10 Carefully remove the elastic from the base of the filter and then remo ve it from the filter holder plate Diagram 11 Empty the bag and clean it with running water or if necessary with slightly soapy water If you use soap rinse it thoroughly whilst turning it over You can also machine wash it following the instructions given on the label inside the bag Also rinse the filter holder plate and remove any dirt caught under the flaps Replace the filter bag by positioning the knot on the holder elastic at the centre of the filter holder and the corners of the bag against the corners of the metallic rods The Zodiac label should be located alongside a rod Position the plastic clip
5. ne track ll In UIC lOdlll THE FOLLO ii IC IN JI if I Length of e The le oT the arantee is fix d at two vears from O Dt Transport damage The user is always re
6. r the water so that the trapped air can escape Squeeze the pads to expel any remaining air There can be 3 reasons for this e The filter bag is full or clogged up simply clean it e The hose weighting level is not correct Contact your retailer e Although the water seems clear your pool contains microscopic algae not visible to the naked eye which are making the sides slippery and are preventing the robot from climbing them In this case carry out an express chlorination session and slightly lower the pH level Do not leave the robot in the water during the express treatment Check that the control unit s mains plug is functioning correctly Check that you have indeed started a Perfect or Turbo cleaning cycle If the problem persists contact your retailer Check that the surface of the foam pads has not become smooth In general we recommend that the pads are changed after a season of usage YOUR SAFETY Your VOYAGER 2X is manufactured according to the strictest standards To ensure complete safety when using your appliance please respect the following recommendations e Only connect the control unit to a plug with a security residual current protection system of 30 mA maximum e Make sure the socket outlet is always and easily accessible e Make sure that the control unit is at least 3 5 metres from the edge of the pool and avoid exposure to direct sunlight e On no account should you ever allow anyone to s
7. s at the top of the rods Replace the filter holder and click it into place CLEANING AND MAINTENANCE The robot must be cleaned regularly with clean or slightly soapy water Solutions such as trichlorethylene or similar must on no account be used Rinse thoroughly in clean water Do not leave your robot to dry in the sun by the pool None of the external mechanical components that are accessible to the user require oiling The robot must be stored on the trolley designed specifically for this task so that the foam pads do not deteriorate and the robot dries quickly The robot is fitted with foam pads We recommend that you change the pads after a season s use It is essential that they are changed as soon as their surface beco mes smooth or worn In order to do this proceed as follows e Turn the robot over Diagram 8 e Push the pads aside to reveal the pad clips e Slide your fingers under the pads in order to release the clips holding them in place Be careful not push them too far Diagram 12 e Remove the used pads and replace them with new ones with the smooth side facing inwards e Replace the clips Diagram 13 e Retighten the pads IN THE EVENT OF A PROBLEM There is still some air trapped in the appliance s shell Repeat the steps of the immersion process carefully respecting the instructions given in section Immersion of the robot Turn the robot over whilst holding it unde
8. wim while the robot is in the pool If by accident the control unit were to fall into the water it is essential that you unplug the electric supply before recovering the control unit e To avoid any risk of an electric shock never open the electric control box Call a qualified technician e Never try to repair the mains power cable Contact the Customer Services Department to have it replaced to avoid any danger e Do not use the appliance in your pool if the water temperature is above 35 C CONFORMITY This appliance has been designed and manufactured in accordance with the following standards e NF EN 50 081 1 June 1992 Electromagnetic compatibility generic emission standard Section I residential commercial and light industry e NF EN 50 082 1 June 1992 Electromagnetic compatibility Generic immunity standard Section I residential commercial and light industry e NF EN 60 335 2 41 Ed 96 amendment A1 Ed 2001 Safety of electrical household appliances and similar products Second section Specific rules for pumps The VOYAGER 2X swimming pool cleaning robot conforms to the following directives e E M C 89 336 CEE and 92 31 CEE e Low voltage 73 23 CEE Those to which it complies The product has been tested under normal usage conditions YOUR GUARANTEE icable even 4 differs om X ES DO NOT COME UNDER THE GUARANTEE WING CIRCUMSTANCES al VWCadl af lg JE CAVETIQAVLe parts SUCN aS t
Download Pdf Manuals
Related Search