NEC LCD8205 LCD User Manual
Contents
1. English 19 Advanced Dimming Auto Dimming Enable Disalbe Auto Dimming control by Abient Light sensor Dim Level Display current Dim Level MAX Dim Ambient Adjusts detected light ambient to set the maximun dimming MIN Dim Ambient Adjusts detected light ambient to set the minimun dimming Ambient Display current detected light ambient level by Lux unit Heat Control Fan Control Controls fan driving option by temperature sensor force on force off Fan Active Adjusts fan driving temperature by celsius degree It works only when the fan control setting Temperature is auto Hysteresis Adjusts fan driving hystereis temperature by celsius degree Main Display the current temperature of Main board and Aux Temperature sensor AUX Video Signals 13xx Mode Auto Select 13xx series native PC video timings 1024 x 768 1280 x 768 1360 x 768 1366 x 768 English 20 Controlling the LCD monitor via RS 232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS 232C terminal LCD Monitor Functions that can be controlled by a personal computer are e Power ON or OFF e Switching between input signals Connection LCD Monitor PC a N s2. s remote control sensor or at a horizontal and vertical angle of within 30 within a distance of about 3 5 m 10 ft Caution Important the remote control system may not function when direct sunlight or strong ee ee illumination strikes the remote control sensor of the LCD monitor or when there is an object in the path Handling the remote control e Do not subject to strong shock e Do not allow water or other liquid to splash the remote control If the remote control gets wet wipe it dry immediately e Avoid exposure to heat and steam e Other than to install the batteries do not open the remote control English 9 Setup 1 Determine the installation location CAUTION Installing your LCD display must be done by a qualified technician Contact your dealer for more information CAUTION IN ORDER TO AID IN MOUNTING A LIFTING DEVICE MUST BE USED IN CONJUNCTION WITH THE ATTACHABLE EYEBOLTS MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY FOUR OR MORE PEOPLE Failure to follow this caution may result in injury if the LCD monitor falls CAUTION Do not mount or operate the display upside down face up or face down CAUTION This LCD has a temperature sensor and cooling fan If the LCD becomes too hot the cooling fan will turn on automatically If the LCD becomes overheated while the cooling fan is running a Caution warning will appear If the Caution warning appears d
3. This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support For proper installation it is strongly recommended to use a trained NEC authorized service person Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer Product warranty does not cover damage caused by improper installation Failure to follow these recommendations could result in voiding the warranty Mounting DO NOT mount the monitor yourself Please ask dealer For proper installation it is strongly recommended to use a trained qualified technician Please inspect the location where the unit is to be mounted Mounting on wall or ceiling is the customer s responsibility Not all walls or ceilings are capable of supporting the weight of the unit Product warranty does not cover damage caused by improper installation remodelling or natural disasters Failure to comply with these recommendations could result in voiding the warranty DO NOT block ventilated openings with mounting accessories or other accessories For NEC Qualified Personnel To insure safe installation use two or more brackets to mount the unit Mount the unit to at least two points on the installation location Please note the following when mounting on wall or ceiling e When using mounting accessories other than those that are NEC approved they must comply with the VESA compati
4. FOLLOWING WHEN SETTING UP AND USING THE MULTI FUNCTION MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e The power supply cord you use must have been approved by and comply with the safety standards of your country Type HO5VV F 3G 1mm should be used in Europe e In UK use a BS approved power cord with molded plug having a black 13A fuse installed for use with this monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e The lamps in this product contain mercury Please dispose according to state local or federal law e Do not bend crimp or otherwise damage the power cord e If glass is broken handle with care e Do not cover vent on monitor e Do not use monitor in high temperature humid dusty or oily areas e If mon
5. LELI SPDIF RS 232C AUDIO IN 1 ag NAN 1 LEL m L L J B cmo OO Y b Pb R VIDE R PC Out RS 232C IN terminal RS 232C Cable om ia siii NOTE If your PC IBM or IBM compatible is equipped only with a 25 pin serial port connector a 25 pin serial port adapter is required Contact your dealer for details In order to function the RS 232C OUT terminal can only be connected to another monitor of the same model Do not connect to other types of equipment To control monitor or multiple monitors that are daisy chained together please use the control command Instructions for the control command can be found on the CD included with the display The file is called External_control_LCD8205 pdf 1 Interface PROTOCOL RS 232C BAUD RATE 9600 bps DATALENGTH 8 bits PARITY BIT NONE STOP BIT 1 bit FLOW CONTROL NONE This LCD monitor uses RXD TXD and GND lines for RS 232C control 2 Control command diagram Please see file External_Control_LCD8205 pdf on the CD ROM English 21 Features Color Control Systems Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards OSD On Screen Display Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus Plug and Play The Microsoft solution with the Windows operatin
6. the main power supply enters the building e Do not install in where people can easily grab and hang onto the unit or the mounting apparatus e When mounting in a recessed area as in a wall leave at least 4 inches 10cm of space between the monitor and the wall for proper ventilation e Allow adequate ventilation or provide air conditioning around the monitor so that heat can properly dissipate away from the unit and mounting apparatus Mounting on ceiling e Ensure that the ceiling is sturdy enough to support the weight of the unit and the mounting apparatus over time against earthquakes unexpected vibrations and other external forces e Be sure the unit is mounted to a solid structure within the ceiling such as a Support beam Secure the monitor using bolts spring lock washers washer and nut e DO NOT mount to areas that have no supporting internal structure DO NOT use wood screws or anchor screws for mounting DO NOT mount the unit to trim or to hanging fixtures Maintenance e Periodically check for loose screws gaps distortions or other problems that may occur with the mounting apparatus If a problem is detected please refer to qualified personnel for service e Regularly check the mounting location for signs of damage or weakness that may occur over time English 5 Attaching Mounting Accessories The display is designed for use with the VESA mounting system In order to aid in mounting a lift
7. the signal from the remote control when using the wireless remote control See also page 9 Glows green when the LCD monitor is in active mode Glows red when the LCD is in POWER OFF standby mode A rt HH English 7 Terminal Panel HDMI DVI PC SPDIF RS 232C HDMI connector To input digital HDMI signals DVI IN DVI I To input digital or analogue RGB signals from a computer SPDIF Optical digital audio out for HDMI input only EXTERNAL CONTROL D Sub 9 pin Connect RS 232C input from external equipment such as a PC in order to control RS 232C functions Audio Input for DVI I connector To input audio signal from computer Component RCA Connecting equipment such as a DVD player HDTV device or Set Top Box AC IN AUDIO IN Cb Pb Cr Pr S iji R Avi AV1 For composite video signal Audio L R To input audio signal from external equipment such as a VCR or DVD player S Video S Video To input the S video Y C separate signal Audio input connects to AV2 s Audio L R av2 AV2 For composite video signal Audio L R To input audio signal from external equipment such as a VCR or DVD player AC IN connector Connects with the supplied power cord EXTERNAL SPEAKER TERMINAL To output the audio signal from O O Q O Note This speaker terminal is for 7W 7W 8 ohm speakers English 8 Wireless Remote Control Ci
8. EC ONS en E EE E A easendoeuauanateamoseanoantmesccciest English 12 Connecting a Personal Computer sssirsssissisisrinenii i ea ai a eaaa Nini English 12 Connect the LCD Monitor to a Personal Computer ccecccseseeeeeeeeeneseeeeeeeeaaseeeeesseeaaeeeeeeseaaaaes English 12 Connecting a DVD Player with component out s snessennesseressrrnresrrrrrsrrrrnsrrrrrsrrrrrsnrrrrsrrrnssnrressrrrenne English 13 Connect the LCD Monitor to a DVD Player ss csioceciecucaiucaclonwsinonsvesneacessutasinadebbaneidonabesexboroatacbarentetiaise English 13 Connecting a DVD Player with HDMI out siceisccuscasreneeecntssanousnadezeas deasonoanenititenekeransesddeasbnedatmsoncnsteteten English 14 Connect the LCD Monitor to a DVD Player ssicincvenusissnsnnsisaniesosinsnavincescnidnncuendaieedensteesedtteumgasaantenadoeide English 14 Connecting to a Stereo Amplifier cicscecsscdeeucsesehucsesccinsmndcaesduapulacodeeienued cioedieavtteealaasuemannssdcasaedstccdtewetensk English 14 Basi CS MON sae gece oes acese aie wee coe tee cere eco exeacete rained aicodetosaaoeticeswusceasncpaiaduatnouureersenadtaraduieannccetdecatactecdan English 15 Power ON and OFF MOSS pg accee sae etettec ne sceserestasecesateelatouaenubicendscsaauein cnaetevtencuaasteedaeuesesuanesenccoaeeietewecaet English 15 OST MIC AOE care here eases ctgsirce vss E ou denies pec eas E a English 16 Using Power Management i cscccccsavionssendacslanstsnccestinanasansedecantnenleesameacignanddadeateeusiasennedab
9. IF Connector Digital Audio Speaker Output Control Power Supply Operational Environment Storage Environment Dimension Weight VESA compatible arm mounting interface Complied Regulatory and Guidelines Power Management Plug amp Play Accessories NOTE Technical specifications are subject to change without notice RS 232C In Temperature Humidity Altitude Temperature Humidity Net Gross Net Gross 81 6 207 cm diagonal 0 744 mm 1920 x 1080 dots Over 16 million colors depending on video card used 600 cd m Typ LCD8205 450 cd m Typ LCD8205 P 2000 1 89 typ CR gt 10 LCD8205 85 typ CR gt 10 LCD8205 P 1500 mm 15 625 15 734 kHz 31 5 kHz 91 1 kHz Analog Input 31 5 kHz 91 1 kHz Digital Input 50 0 85 0 Hz 25 2 MHz 162 0 MHz 1428 48 x 803 52 mm DVI HDCP VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz 0 7 Vp p Input Impedance 75 ohm VGA60 SVGA60 XGA60 WXGA60 SXGA60 UXGA60 1920X1080 60Hz Separate TTL level Pos Neg Composite sync on Green Video 0 3 Vp p Neg HDMI 1080p 1080i 720p 50Hz 60Hz 576p 50Hz 480p 60Hz 1 0 Vp p Input Impedance 75 ohm NTSC PAL SECAM 4 43NTSC PAL60 Y 1 0 Vp p 75 ohm C 0 286 Vp p 75 ohm NTSC 0 3 Vp p 75 ohm PAL SECAM NTSC PAL SECAM 4 43NTSC PAL60 Y 1 0 Vp p 750hm Cb Cr Pb Pr 0 7 Vp p 75 ohm HDTV DVD 1080p 1080i 720p 50Hz 60Hz 576p 50Hz 480p 60Hz 5761 50H
10. Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation Approx 900W Green Energy Saving Mode Less than 15W Red blinking Off Mode Less than 1W WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 26
11. MENU button Press UP and DOWN Press Right button to Press EXIT to exit to show OSD menu to select the main enter the sub menu menu menu O EXIT m O O A O EXIT O CO Remote Control at O Ob vo nO O Of vo AO OF OB vo a O e Co CI w CI Press MENU button Press CH and CH Press VOL button to Press MENU button to show OSD menu buttons to select the enter the sub menu to back to previous main menu menu Control Panel CH CH VOL VOL gt SEL MENU English 17 OSD Setting Picture Picture Mode User Store last value at User setting Dynamic Selection of the picture appearance Standard Movie Brightness Adjust the brightness Contrast Adjust the Contrast Color av1 Av2 s Video Component Adjust the Color Tint Av1 Av2 S Video Component Adjust the Tint Sharpness Adjust the Sharpness Phase Component Adjust the Phase Color Temp User Pc Dvi HDMI This Function is for user setting of color Temp Cool 2 This Function is for selection of preset Color value Cool 1 Normal Warm 1 Warm 2 7 z 16 9 Select Screen Format 2 So 3 T D Panorama Homavtiavas video Zoom 1 T gt gt v wm Ss ro Q O So 3 z 5 D Zoome 14 9 HDMV AV1 AV2 S Video Component 1 1 ovw Pc PC only Auto in progress Automatically Tuning Phase Adjust the Phas
12. User s Manual NEC MultiSync LCD8205 MultiSync LCD8205 P Index Declaration of conformity oaieccinsteaetrecanen sep ceaesteranst cetciecadoac seatea ton tue pecidocacien oateseadeeagdeenacamteepeadataansedeecsaceneuesacesnece English 1 Important Information saaaceectinnezcecuateousnceactencieeavnsectieesneceatecetaqnashqaecaentatd bqeutencapangaiaasesdeasnecaudientseaseeneeecateeanestes English 2 Warning G AUO a E Secieyaeiiel toiseeieeeeendinadsenqaseenaceee English 2 Declara essea EE E EEEE REEERE English 2 Safety Precautions Maintenance amp Recommended Use ccccccccceecesssseeeeeeeeaneeeeeeeseaaaeeeeesseaaaeeeeeeseaaaees English 3 COMNEN eao E E E N E E English 4 DVS EE ET aE P E IE PA td asin E I I P E E T EE E EEE A A EEE T T English 5 Farts Name and FUNCUONS sereccruierrss binini ia a ines EE E E a E eE Ee a aro English 7 Connal P anoa E E E English 7 Terminal Pane aesaceesetececaeesecousan sutton saeactosaorslnnuedoantnraniqeatesnaiecteasscdiecaceaeantaraieneotnedate uemanedeestiabatacntcncss English 8 Wireless Remote Control geist octeesetcresecte tae eda eee eaaa diee aa ets wcaueseteaeiassuanesseaienensseuse English 9 Operating Range for the Remote Control cccccssececceesseecceesseecceeseeeceeaeeeceseaseeeesageeeessuseeessenseeeess English 9 Handling the remote COMIN ON izes cnstenscunscoracwaientendsnqcnstmataaneniaeetas isede ein riai isaisa English 9 SUD e E E E E E English 10 CONN
13. ase adjust the following item based on the application being used SCREEN SAVER See page 19 It is recommended that the FAN CONTROL setting See page 20 be turned to ON also English 11 Connections Before making connections First turn off the power of all the attached equipment and make connections Refer to the user manual included with each separate piece of equipment Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer s screen image Some video cards and a pixel clock over 162MHz may not display an image correctly Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically lt Factory preset signal timing gt Scanning frequency eens Compressed image Recommended resolution Connect the LCD Monitor to a Personal Computer e To connect the DVI IN connector on the LCD monitor use the supplied PC Video RGB signal cable DVI D to DVI D DVI A to mini D sub 15 pin LCD monitor HDMI DVI PC SPDIF RS 232C O DVI A DVI D To audio output To analog RGB output Mini D sub 15 pin Taw Of rake Personal DVI D connector Computer English 12 Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video Refer to yo
14. autebasezcsiaaesumebasules English 16 PICU IZO scire in enipe a e aa a e e a a Ee a a aea English 16 OSD On Screen Display Controls n nennnnnsnnnnnennnnsstrnnsrnrresrnrrnsnrrrnsnrrrnsrrrrrstrrrrsnrrnstrrnsnrrnnnrrennnnrennrnnene English 17 PICU r E S too pk re naetun ava edvagateccameeainseewanseinsepnnee tans English 18 ON i a PA EEE A TAA E E A EEE E E P E AE oasewasaii ea E E E E EE ETEA English 19 SLL E ene er ener PE N E A NE S N E A eS EE E eee T English 19 Controlling the LCD monitor via RS 232C Remote Control cecccccccececeeeeeeeeeseeeeeeseeaaaeeeeesseaaaeeeeeeseaaaaes English 21 EEE care A I vrei E EE E nen sree E A ET sso T E E VA A ET E T T English 22 WOES NODU sarisossesrerireieer niren i eS eea er a eaeoe aA ea e eie r a eea English 23 Pece ON e E ieteccaeyedetawtacan English 24 PIAS SSG soseen ere r E aE o E ar r EAE English 25 Manufacturer s Recycling and Energy Information ccccseccccesseeececeeeceeeceeeeeeeseseeeeceuceeesssaeeeesssaeeeeesaaeeees English 26 Declaration of conformity For USA FCC Information Use the attached specified cables with the MultiSync LCD8205 L828N0 MultiSync LCD8205 P L828N0 color display so as not to interfere with radio and television reception 1 Please use the supplied power cord or equivalent to ensure FCC compliance 2 Please use the supplied shielded video signal cable Use of other cables and adapters may cause interference with radio and te
15. ble FDMlv1 mounting method e NEC strongly recommends Unit using size M8 screws N 10 18 mm thickness of bracket and washer in length If using screws Mounting J Bracket Washer m Came longer than 10 18 mm 10 18 mm check the depth of the hole AI Thickness R ded F of bracket eee eee and washer Force 1125 1375Necm Screw length should equal NEC recommends mounting depth of hole 10 18 mm interfaces that comply with the thickness of mounting UL1678 standard in North bracket and washer America e Prior to mounting inspect the installation location to insure that it is strong enough to support the weight of the unit so that the unit will be safe from harm e Refer to the instructions included with the mounting equipment for detailed information Orientation e When using the display in the portrait position the monitor should be rotated clockwise so that the left side is moved to the top and the LED indicator light is on the bottom This will allow for proper ventilation and will extend the lifetime of the monitor Improper ventilation may shorten the lifetime of the monitor LED Indicator Mounting location e The ceiling and wall must be strong enough to support the monitor and mounting accessories e DO NOT install in locations where a door or gate can hit the unit e DO NOT install in areas where the unit will be subjected to strong vibrations and dust e DO NOT install near where
16. e Value by Manual H Position Adjust the H Position Value by Manual V Position Adjust the V Position Value by Manual Frequency Adjust the Frequency Value by Manual Video Wall Set X This function is for Video Wall Settings Each function fix the ID of Position amp Wall format Set Y Set X Max Set Y Max Set X Gap O iN oe ae oO i p 7 3 p as 2 O O a oO m om 2 Set Y Gap English 18 Sound User This function use setting Equalizer value Standard Selection of preset Sound mode Equalizer Music Movie Speech Volume Adjust the sound volume level Balance Tuning the sound balance between left and right Equalizer 10 KHz The value of 5 Band equalizer are preset 3 KHz These values are changed by user with user mode setting 1 KHz 300 Hz 100 Hz z O On Off Automatic volume level control z r U Stereo L R MTS feature is selecting one L or R or both L R channel of sound input generating bilingual stereo sound output Dual 1 L Dual 2 R Setup Reset as default setting Clock Time setting by up and down buttons On Timer Setting power on time Off Timer Setting power off time Language This function is use to select preset language English Spanish Portugu s German French OSD Tone J 2 3 Off On Disable blending OSD background with video image Screen Saver Moving dot Enables screen saver function to avoid panel burning BG Gray
17. e appropriate resolution has been selected If not select corresponding option No Sound e Check to see if speaker cable is properly connected e Check to see if mute is activated e Check to see if volume is set at minimum Remote Control is not available e Check the Remote Control s batteries status e Check if batteries are inserted correctly e Check if the Remote Control is pointing at the monitor s remote sensor e The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor or when there is an object in the path RS 232C does not work e Make sure the monitor is not in Power OFF Standby mode LED is in Red See page 16 Either light vertical or horizontal stripes may appear depending on the specific display pattern This is no product fault or degradation English 23 Specifications Product Specifications LCD Module Frequency Pixel Clock Viewable Size Input Signal Pixel Pitch Resolution Color Brightness Contrast Ratio Viewing Angle Design View Distance Horizontal Vertical DVI DVI I Digital RGB P O DVI I Analog RGB Sync HDMI HDMI Connector Digital RGB AV1 AV2 RCA Composite S VIDEO Mini DIN 4pin S VIDEO COMPONENT RCA Y Cb Pb Cr Pr Component AUDIO AUDIO Input STEREO Mini Jack Analog Audio RCA L R x3 HDMI Connector Digital Audio AUDIO Output SPD
18. es RXD TXD and GND lines for RS 232C control O4 30 O2 1O XL TXO TXO B rE NC NC Shield TXC TXC TXC Sy A unn D SUB 9P English 25 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in
19. evices NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Image is unstable unfocused or swimming is apparent e Signal cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment When the display mode is changed the OSD Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e f your text is garbled change the video mode to non interlace and use 60HZ refresh rate Image of component signal is greenish e Check to see if the DVD HD input connector is selected LED on monitor is not lit no green or red color can be seen e Power Switch should be in the ON position and power cord should be connected e Make certain the computer is not in a power saving mode touch the keyboard or mouse Display image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the coarse adjustment e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode Selected resolution is not displayed properly e Use OSD Display Mode to enter Information menu and confirm that th
20. g system facilitates setup and installation by allowing the monitor to send its capabilities Such as screen size and resolutions supported directly to your computer automatically optimizing display performance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size VESA Standard FDMlv1 Mounting Interface Allows users to connect their LCD monitor to any VESA standard FDMlv1 third party mounting arm or bracket Allows for the monitor to be mounted on a wall or an arm using any third party compliant device NEC recommends using mounting interface that comply with TUV GS and or UL1678 standard in North America DVI D The digital only subset of DVI ratified by the Digital Display Working Group DDWG for digital connections between computers and displays As a digital only connector analog support is not provided for a DVI D connector As a DVI based digital only connection only a simple adapter is necessary for compatibility between DVI D and other DVI based digital connectors such as DFP and P amp D The DVI interface of this display supports HDCP Video Wall Shows one image over multiple
21. has been included Therefore it should be read carefully in order to avoid any problems A A CAUTION Please use the power cord provided with this display in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country European r D Sa Ip When operating the MultiSync LCD8205 MultiSync LCD8205 P monitor with its AC 125 240V power supply use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE This product can only be serviced in the country where it was purchased Declaration Declaration of the Manufacturer We hereby certify that the color monitor MultiSync and marked with LCD8205 L828N0 MultiSync LCD8205 P L828N0 is in compliance with Council Directive 2006 95 EC EN 60950 1 Council Directive 2004 108 EC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 NEC Display Solutions Ltd 4 13 23 Shibaura Minato Ku Tokyo 108 0023 Japan Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures English 2 Safety Precautions Maintenance amp Recommended Use FOR OPTIMUM PERFORMANCE PLEASE NOTE THE
22. icator Power ON Power OFF Standby Green Power Save Red blinking Power consumption under 15W When in Power OFF Standby mode RS 232C control do not function Using Power Management The LCD monitor follows the VESA approved DPM Power Management function The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period The power management feature on your new display has been set to the ON mode This allows your display to enter a Power Saving Mode when no signal is applied This could potentially increase the life and decrease the power consumption of the display Picture Size DVI PC 16 9 1 1 4 3 AO HDMI AV1 AV2 S Video Component 16 9 Panorama Zoom1i Zoom2 4 3 14 9 Aspect ratio dail 1 Unchanged view Picture size example 16 9 CO C2 C2 CO Panorama C2 O C gt 4 3 4 3 1024 x 768 input 1 Grey areas indicate unused portions of the screen English 16 OSD On Screen Display Controls NOTE Some functions may not be available depending on the model or optional equipment Main Menu Item i Picture Picture Mode User Main Menu Icons i Color Temp Size t Yideo Wall Key Guide Press
23. ing device must be used in conjunction with the attachable eyebolts 1 Attach eyebolts for mounting This model is equipped with attachable eyebolts to aid in mounting e Place the washer over the threads of the eyebolt e Screw the eyebolts into eyebolt holes as shown in the picture e Be sure eyebolts are secure e In order to move the monitor into position use a lifting device attached to the eyebolts DO NOT mount the monitor using only the eyebolts Use an approved mounting accessory Eyebolt Q Washer Q Eyebolt Hole 2 Attach Mounting Accessories Be careful to avoid tipping monitor when attaching accessories After accessories are attached stand can be removed 800 mm VESA Mounting Interface Mounting accessories can be attached with the monitor in the face down position To avoid damaging the screen face place the protective sheet on the table underneath the LCD The protective sheet was wrapped around the LCD in the original packaging Make sure there is nothing on the table that can damage the monitor When using mounting accessories other than NEC compliant and approved they must comply with the VESA compatible mounting method NEC strongly recommends using screws M8 size and 10 18 mm in length If using screws longer than 18 mm check the depth of the hole Recommended Fasten Force 1125 1375Necm NEC recommends using a mounting interface that c
24. iscontinue use and allow the unit to cool Using the cooling fan will reduce the likelihood of early circuit failure and may help reduce image degradation and Image Persistance If the LCD is used in an enclosed area or if the LCD panel is covered with a protective screen please check the inside temperature of the monitor by using the HEAT CONTROL control in the OSD see page 20 If the temperature is higher than the normal operating temperature please turn the FAN CONTROL to ON within the HEAT CONTROL menu within the OSD see page 20 IMPORTANT Lay the protective sheet which was wrapped around the LCD monitor when it was packaged beneath the LCD monitor so as not to scratch the panel 2 Install the remote control batteries The remote control is powered by two 1 5V AAA batteries To install or replace batteries o O O A Press and slide to open the cover B Align the batteries according to the and indications inside the case C Replace the cover CAUTION Incorrect usage of batteries can result in leaks or bursting NEC recommends the following battery use Place AAA size batteries matching the and signs on each battery to the and signs of the battery compartment e Do not mix battery brands e Do not combine new and old batteries This can shorten battery life or cause liquid leakage of batteries e Remove dead batteries immediately to preve
25. itor or glass is broken do not come in contact with the liquid crystal and handle with care e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of the monitor e The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Please clean the holes of back cabinet to reject dirt and dust at least once a year because of set reliability e If using the cooling fan continuously it s recommended to wipe holes a minimum of once a month e Do not touch LCD panel surface while transporting mounting and setting Applying pressure on the LCD panel can cause serious damage Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the monitor e Ifthe monitor has been exposed to rain or water e If the monitor has been dropped or the cabinet damaged e If the monitor does not operate normally by following operating instructions Recommended Use e For optimum performance allow 20 minutes for warm up e Res
26. levision reception 2 This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 For Canada Canadian Department of Communications Compliance Statement DOC This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 Windows is a registered trademark of Microsoft C
27. nk EPG DTVCH DTVINFO FAV NOTE The button without explanation doesn t work POWER button Switches the power on off SOURCE button Enter Input Source OSD menu DVI PC HDMI AV 1 AV2 S Video and Component MUTE button Turns on off mute function INFO button Turns on off the information OSD STILL button Toggles picture status between motion and still image DUAL I II button Select MTS ARC button Select picture size 4 3 16 9 1 1 for DVI PC 16 9 Panorama Zoom1 Zoom2 4 3 14 9 1 1 for AV 1 AV2 S Video Component SSM button Select sound Mode User Standard Music Movie and Speech PSM button Select Picture Mode User Dynamic Standard Movies and Mild PC button Selects input source of DVI connector MENU button Turns on the menu mode EXIT button Turns off the menu mode CH button Acts as A W button to move the highlighted area up or down to select adjustment items within OSD menu VOL button Increases or decreases audio output level Increases or decreases the adjustment level within OSD menu settings ENTER button Makes selection Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor s remote sensor during button operation Use the remote control within a distance of about 7 m 23 ft from the front of the LCD monitor
28. nt battery acid from leaking into the battery compartment e Do not touch exposed battery acid it may injure skin NOTE If you do not intend to use the Remote Control for a long period of time remove the batteries 3 Connect external equipment See pages 12 14 e To protect the external equipment turn off the main power before making connections e Refer to your equipment user manual for further information 4 Connect the supplied power cord The equipment should be installed close to an easily accessible power outlet Please fasten power cord to the LCD monitor by attaching the screw and clamp e Fully insert the prongs into the power outlet socket A loose connection may cause image degradation NOTE Please refer to the Safety Precautions and Maintenance section of this manual for proper selection of AC power cord English 10 5 Switch on the power of all the attached external equipment When connected with a computer switch on the power of the computer first 6 Operate the attached external equipment Display the signal from the desired input source 7 Adjust the sound Make volume adjustments when required 8 Adjust the screen See page 18 Make adjustments of the screen display position when necessary 9 Adjust the image See page 18 Make adjustments such as brightness or contrast when required 10 Recommended Adjustments To reduce the risk of the Image Persistence ple
29. omplies with UL1678 standard in North America 3 Ventilation Requirements When mounting in an enclosed space or recessed area leave adequate room between the monitor and the enclosure to allow heat to disperse as shown below 100 mm 100 mm 100 mm 100 mm 4 Attach Mounting Accessories The display is designed for use with the VESA mounting system When using mounting accessories other than NEC compliant and approved they must comply with the VESA compatible mounting method NEC strongly recommends using screws M8 size and 10 18 mm in length If using screws longer than 18 mm check the depth of the hole Recommended Fasten Force 1125 1375Necm NEC recommends using a mounting interface that complies with UL1678 standard in North America English 6 Parts Name and Functions Control Panel CH CH VOL VOL POWER button CD Switches the power on off CH button Acts as A V button to move the highlighted area up or down to select adjustment items within OSD menu VOL button Increases or decreases audio output level Increases or decreases the adjustment level within OSD menu settings O SEL button Enter Input Source OSD menu DVI PC HDMI AV1 AV2 S Video and Component MENU button Activates the OSD menu when the OSD menu is turned off Move to previous OSD menu Remote control sensor and Power Indicator Receives
30. orporation NEC is a registered trademark of NEC Corporation OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland All other brands and product names are trademarks or registered trademarks of their respective owners HOM HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC English 1 Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNITS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL J CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit
31. oth NOTE The surface of the cabinet is composed of many types of plastic DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Rubber or vinyl should not be in contact with the cabinet for an extended period of time These types of fluids and materials can cause the paint to deteriorate crack or peel English 3 Contents Your new MultiSync LCD monitor box should contain the following e LCD monitor e Screw for clamp M4 x 10 x 2 e Power Cord e CD ROM e Video Signal Cable e Eyebolt x 2 e Setup Manual e Washer x 2 e Wireless Remote Control and AAA Batteries e Hanger bolt x 8 e Clamp 15 pin mini D SUB male to DVI A Om 6 Screw for clamp M4 x 10 x2 Gi Washer x 2 Clamp Power Cord Hanger bolt x 8 Setup Manual Eyebolt x 2 Setup Manual Wireless Remote Control and AAA Batteries 1 Type and number of power cords included will depend on the where the LCD monitor is to be shipped When more than one power cord is included please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country Install the stands at the time of unpacking if the display will be used with the stand Remember to save your original box and packing material to transport or ship the monitor English 4 Installation
32. screens with accuracy while compensating for bezel width English 22 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The display card should be completely seated in its slot e Front Power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins Power Button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor Image persistence e Please be aware that LCD Technology may experience a phenomenon known as Image Persistence Image Persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display d
33. t your eyes periodically by focusing on an object at least 5 feet away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness contrast and sharpness controls to enhance readability e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomic benefits we recommend the following e Use the preset Size and Position controls with standard signals e Use the preset Color Setting e Use non interlaced signals e Do not use primary color blue on a dark background as it is difficult to see and may produce eye fatigue due to insufficient contrast Cleaning the LCD Panel e When the liquid crystal panel is stained with dust or dirt please wipe with soft cloth gently e Please do not rub the LCD panel with hard material e Please do not apply pressure to the LCD surface e Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface Cleaning the Cabinet e Unplug the power supply e Gently wipe the cabinet with a soft cloth e To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cl
34. ur DVD player user s manual for more information Connect the LCD Monitor to a DVD Player e To connect the Component connector RCA on the LCD monitor use an RCA connector cable sold separately LCD monitor HDMI DVI PC SPDIF RS 232C RCA To DVD Component video output To audio right output To audio left output English 13 Connecting a DVD Player with HDMI out Connecting your DVD player to your LCD monitor will enable you to display DVD video Refer to your DVD player user s manual for more information Connect the LCD Monitor to a DVD Player e Please use an HDMI cable with HDMI logo e t may take a moment for the signal to appear e PC DVI signals are not supported To HDMI output ia HDMI connector LCD monitor Connecting to a Stereo Amplifier You can connect your stereo amplifier to your LCD monitor Refer to your amplifier owner s manual for more information To HDMI output Amplifier eo OOo Je O JUUUIT oO y External speaker English 14 LCD monitor External speaker Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red while powered off Power Button a English 15 Power Ind
35. z 480i 60Hz Stereo L R 0 5 Vrms PCM 32 44 1 48 KHz 16 20 24bit PCM 32 44 1 48 KHz 16 20 24bit External Speaker Jack 7 W 7 W 8 ohm 9 Pin D sub 9 5 4 25 A 100 240VAC 50 60Hz 5 40 C LCD8205 5 35 C LCD8205 P 20 80 without condensation 0 3000 m 20 60 C 10 90 without condensation 90 3 5 x Temp 40 C regarding over 40 C 1926 W x 1137 H x 150 D mm LCD8205 1926 W x 1137 H x 160 D mm LCD8205 P D m D m 2216 W x 1387 H x 710 D mm without pallet 132 Kg LCD8205 157 Kg LCD8205 P 173 Kg LCD8205 199 Kg LCD8205 P 800 mm X 800 mm 4 Holes UL60950 1 CSA C22 2 No 60950 1 TUV EN60950 1 FCC A DOC A EN55022 A EN55024 EN61000 3 2 EN61000 3 3 CE GOST R VESA DPM VESA DDC2B DDC CI User s manual Power Cord Video Signal Cable Remote Control AAA Battery x 2 Clamp Screw x 2 CD ROM Eyebolt x 2 Washer x 2 Hanger bolt x 8 Compressed image English 24 Pin Assignment 1 S VIDEO input VIDEO Y Luminance C Chroma 2 Digital Analog RGB input DVI I Pin Assignment of DVI connector ee er pe axe ooe fe a Shield x27 Txa 11 Shield TxA Tx 19 afno efje fo s sime a 6 D0G Serial Giock 14 5Vpower 22 ra Nc 16 Hotpug detect 24 3 RS 232C input Pin No Name ne ooo gt o s w connected to 4 B E 7 connected io 188 e connected io 187 fe no This LCD monitor us
Download Pdf Manuals
Related Search