Quad-C LED Moving Wash SI
Contents
1. CE Quad C LED Moving Wash SI 055 User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing Color Imagination s moving head For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Color Imagination s moving wash is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos SI 055 adopts CREE 10W 4 in 1 LED lamps which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head one Signal Cable one Omega Clamp one User Manual one Power Cable one Safety Chain one 10 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of2. V 50 60Hz LED Quantities 36PCS 10W CREE Quad LEDs Control Signal DMX512 master slave and sound activated or auto operation Control Channel 37 DMX Channels Power Consumption 420W Dimensions 350x260x350mm Packing Dimensions 430x300x400mm Net Weight 10 5kg Gross Weight 11 5kg 2 Safety Instructions This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ZT Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect f
3. XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 ON PIN3 PIN2 6 LCD Display Operations nter up down N Enter Enter ueidonn KETIN press menu to back s A OF E ress menu to back Enter up down 540 630 Enter up down Enter an YES or ity press menu to back Ent id Ent een sar naa press menu to back Enter DMX addre Pan invert Pan angle Enter gt press menu to back Tilt invert press menu to back Slave mode Enter sound mode press menu to back Enter auto mode press menu to back Enter Enter up down Enter up down CH xx Date xxx Manual Manually operate Choose channal Number of controlled Restore All the motor reset All the data change to original The display will close after 30 seconds without operations
4. and blackout for all four colors 32 DMX channels DMX512 master slave and sound activated controllable or auto operation Blue background LCD display 7 DMX Channels Channel Function Values Description 1 PAN 0 255 Pan Movement 540 2 TILT 0 255 Tilt Movement 270 3 Dimmer 0 255 0 100 Linear dimmer 4 Strobe 0 255 Strobe effect from slow to fast 5 Red 0 255 0 100 Red dimmer from dark to bright 6 Green 0 255 0 100 Green dimmer from dark to bright 7 Blue 0 255 0 100 Blue dimmer from dark to bright 8 White 0 255 0 100 White dimmer from dark to bright 9 Speed 0 255 Speed of PAN TILT movement 10 Macro 0 255 Macro effect 11 Color Fading 0 255 Color fading effect 12 Auto 0 255 Auto running with built in programs 13 Reset 0 255 Reset 14 Red 0 255 Red in A section 15 Green 0 255 Green in A section 16 Blue 0 255 Blue in A section 17 White 0 255 White in A section 18 Red 0 255 Red in B section 19 Green 0 255 Green in B section 20 Blue 0 255 Blue in B section 21 White 0 255 White in B section 22 Red 0 255 Red in C section 23 Green 0 255 Green in C section 24 Blue 0 255 Blue in C section 25 White 0 255 White in C section 26 Red 0 255 Red in D section 27 Green 0 255 Green in D section 28 Blue 0 255 Blue in D section 4 Installation via clamp Please refer to the picture below 1 Omega holders 2 Clamp 3 Safety rop
5. cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition Its recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies lt is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 29 White 0 255 White in D section 30 Red 0 255 Red in E section 31 Green 0 255 Green in E section 32 Blue 0 255 Blue in E section 8 Features 36PCS 10W high power CREE Quad Color LEDs Specific optic system 50 000 hours lifespan and low power consumption Smooth and precise resolution for PAN TILT movement 540 630 pan and 265 tilt movement Scan position memory auto reposition after unexpected movement RGBW color mixing system LED shutter LED dimming LED rainbow effect Macros effect Strobe effect with 18 flashes per second and pulse effect General dimming
6. e 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw 5 DMX 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal SQ 120 ohms lt 5 DMX512 DMX controller Address 26 Address13 Address 1 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an
7. rom the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is an LED wash light for onsite decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might
8. the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer 9 Technical Specifications Input Voltage AC90 2600
Download Pdf Manuals
Related Search