Manual - Videcon
Contents
1. Lens Day Night Wide Dynamic Range 148 2 x106mm CVP9304 420TVL 0 3 Lux 4mm Lens 148 35 x105mm CVP9314 650TVL 0 03Lux 4mm Lens 148 35 2 x105mm CVP9324 650TVL 0 03Lux 2 8 10mm Lens 148 35 e2 x105mm CVP9324DN 650TVL 0 03 Lux 2 8 10mm Day Night 148 35 2 x105mm CVP9324LL 600TVL 0 0002 Lux DSS Sens Up on 2 8 10mm Lens 148 35 2 x105mm CVP9324WDR 690TVL 0 01 Lux 2 8 10mm Lens Day Night Wide Dynamic Range 148 35 2 x105mm CBP6314DNIR 600TVL 4mm Lens IR LED 148 2 x106mm CBP6324DNIR 650TVL 2 8 10mm Lens IR LED ICR 148 2 x106mm CVP9314DNIR 600TVL 4mm Lens IR LED 148 35 x105mm CVP9324DNIR 650TVL 2 8 10mm Lens IR LED ICR 148 35 x105mm CVP BRK Wall bracket for use with all CVP dome cameras Concept C Pro2. resistant dome casing CBP4304 4324 CVP9304 94 64 94 64 oo o co z LO NN S o LO a co LO 147 97 86 00 82 50 106 10 105 00 SPECIFICATION MODEL Image Sensor Effective Pixels Horizontal Resolution Min Illumination Lens Day amp Night S N Ratio White Balance AGC BLC Sync System BNC Video Output Input Voltage Power Consumption Operating Temperature Dimension Weight PAL 500 H x 582 V NTSC 510 H x 494 V Fixed Lens f 4mm Auto Iris Vari focal lens F 4 9mm Colour Only 12v DC 10 C 50 C RH90 MAX 148x106 DxH 650g Design and specification are subject to change without notice SPECIFICATION MODEL Effective Pixels Horizontal Resolution Lens Fixed Lens f 4mm AGC Input Voltage 12v DC Operating Temperature 10 C 50 C RH9096 MAX Design and specification are subject to change without notice CONCEPT PRO DOME CAMERA RANGE CBP3212 A80TVL 0 3 Lux 3 6mm Lens 90 2 x62mm CBP5112 420TVL 0 3 Lux 3 6mm Lens 128 x93mm CBP5212 480TVL 0 3 Lux 3 6mm Lens 128 x93mm CBP4304 420TVL 0 3 Lux 4mm Lens 148 2 x106mm CBP5314 650TVL 0 03Lux 4mm Lens 148 2 x106mm CBP4324 420TVL 0 3 Lux 4 9mm Lens 148 2 x106mm CBP6324 650TVL 0 03Lux 2 8 10mm Lens 148 2 x106mm CBP6324 B 650TVL 0 03 Lux 2 8 10mm Lens 148 2 x106mm Black casing CBP6324DN 650TVL 0 03 Lux 2 8 10mm Day Night 148 2 x106mm CBP6324WDR 690TVL 0 01 Lux 2 8 10mm
3. Concept lt gt Pro CBP4304 CBP4324 CVP9304 Colour Dome Camera USER MANUAL CAUTION 10 Tk T2 This installation should be made by a qualified service person and should abide to all local codes Avoid installation on a surface subjected to frequent vibration or shocks Do not operate the camera beyond its temperature range or power source ratings Should any damage or suspected damage occur shutdown the power source unplug and contact your service provider Do not install the camera under unstable lighting conditions Severe lighting change or flicker can cause the camera to work improperly Never use the camera close to a gas or oil leak Do not disassemble the camera Never keep the camera face to strong light directly this can damage the CCD Ensure all removable covers are replaced to protect the inner components Do not install near devices which emit a strong electro magnetic field Use a dry or damp cloth only for cleaning Internal dome only Do not drop the camera or subject the unit to physical shocks PLEASE FOLLOW THE ABOVE CAUTIONS FAILURE TO DO SO MAY INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY Remark Changes or modifications not expressly approved by the manufacturer can cause the camera to be damaged and become inoperable This may invalidate the user warranty INTERNAL DOME INSTALLATION CBP4304 4324 Important Ensure all cautionary procedures are observed during in
4. d dome cover screwdriver Attach the weatherproof sealing pad to the base of the dome with the sticky side against the camera Using the supplied fitting screws securely attach the camera to the drilled surface Please note To ensure correct weatherproof you must use the enclosed fitting screws and weatherproof washers Adjust the tri axis gimbal zoom focus to give the required image of the area to be monitored Replace the dome cover and tighten the dome cover screws using the supplied dome cover screw driver Carefully clean the dome surface with a soft lint free cloth CVP9304 PACKING CONTENTS S S Wall Plugs Conduet hole cover Fitting Screws Dome cover opener screwdriver X4 X1 X4 X1 Weatherproof sealing pad x1 0000 Weatherproof Mounting Template sealing washers X1 X8 CONNECTION Connect the video out port to your video cable running to the monitor recorder Check the power supply is of the correct level and connect your power supply into the power port on the Camera View the picture on a monitoring device to check the power and video connection is working properly Troubleshooting Ensure all power and cable connections are correct with the Camera and DVR If all power and cable connections are correct and the camera picture can not be produced then contact your supplier for technical support Tri Axis Gimbal Example shows vandal
5. stallation FIXING TO A WALL It is recommended the camera is tested during the most demanding environmental conditions such as low light or bright sunlight to ensure continuity of effective CCTV Selma monitoring Remove the camera unit carefully from the box reserving the accessory contents in a safe place Use the supplied mounting template to mark the space for drilling Remove the dome cover using a suitable coin or screwdriver Using the supplied fitting screws securely attach the camera to the drilled surface Adjust the tri axis gimbal zoom focus to give the required image of the area to be monitored Replace the dome cover by pushing firmly in place onto the base Carefully clean the dome surface with a soft lint free cloth CBP4304 4324 PACKING CONTENTS Ey Duna gt ae Pe Wall Plugs Fitting Screws Mounting Template X4 X4 X1 VANDAL RESISTANT DOME INSTALLATION CVP9304 Important Ensure all cautionary procedures are observed during installation FIXING TO A WALL It is recommended the camera is tested during the most demanding environmental conditions such as low light or bright sunlight to ensure continuity of effective CCTV monitoring Ceiling 1 2 Remove the camera unit carefully from the box reserving the accessory contents in a safe place Use the supplied mounting template to mark the space for drilling Remove the dome cover using the supplie
Download Pdf Manuals
Related Search