User Manual
Contents
1. 7 Add SATA power cable onto the embedded board and SATADOM Screw No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Alvays at the toreivent of innoveiian TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 21 www bestek tw No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C arben of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 22 oo www bestek tw e 3 1 Turning On The System Add your cables such as USB keyboard USB mouse and DVI or HDMI Cable as the merest devices to control the system Leave the power cable as the last cable to be added right on DC Inlet as indicated below with blue circle In case a power adaptor is used please ensure that 1 The output DC voltage ranges between 10Vdc 28Vdc 2 The polarity positive or negative of the power cable has been well taken into consideration 3 The AC input range of the power adaptor matches the available AC source Turn On the Power In some cases depending on whether a BIOS setting has been configured to allow immediate power on upon the delivery of AC power system might come right up unexpectedly for no particular reason Please refer to BIOS section for details as to Restore AC Power Loss Have you intended to bring it down simply press once the power switch located at the right lower corner with yellow ci2. 3 Put through the two antenna jacks 4 Add one washer ring on each jack SHPPPP PPLE TOS AMMAL Antenna Jack with long cable Antenna Jack with short cable Ring 1 Ring 2 5 Attach the other end of the antenna onto Wireless module 6 Connector external antenna onto antenna jack RF Cables No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Absa tt te deefe steet TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 19 oc www bestek tw e 2 8 Accessing SIM Card 1 Slide to move the SIM card holder to open position and lift up the top cover 2 Manage to also slide the SIM card into the top cover SIM Card Holder SIM Card 3 Push down the top cover and slide to move the SIM card holder back to close position No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the dretten of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 20 oo www bestek tw e 2 9 Installing SATADOM 1 Locate the SATA Connector and also the screw next to it 2 Now remove this screw 3 Find the stand off in the accessory bag and add this stand off onto where the screw was seated SATA Connector Copper Post Screw 4 Add your SATADOM Note that only right angled can be used 5 Push SATADOM into SATA connector 6 Add the screw back on SATADOM into the stand off
3. Always at the forefront of innovation EMAIL sales bestek tp com tw oo www bestek tw e 1 3 System Layout 9 kalla L 185 00 194 00 206 00 Figure 1 1 System Layout of FEB 1251 No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Absa tt te deefe steet TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw emm www bestek tw e 1 4 Indicators amp Features gt Front View OD AX KA RRL Me 4272 2222 LLL f ke X 1110 9 8 7 DB9 RS 232 DB9 RS 232 422 485 DB9 RS 232 422 485 DB9 RS 232 Power Switch Antenna Cut Out Power LED Green HDD LED Yellow Microphone Jack Line Out Jack 1 USB 2 0 1 USB 2 0 Antenna Cut Out oS EE AE SS A kA KA ke No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Age at tie tevelvant ai iniii TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 10 o _ www bestek tw e gt Rear View 34959 6 gt 1 10 28Vdc Power Input 2 DVI I 3 HDMI 4 2 USB 2 0 5 2 USB 2 0 D LANT 7 LAN 8 CFast Socket No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Age at tie tevelvant ai iniii TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 11 co www bestek tw d G No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan
4. and a monitor is thus suggested Dax Sal e No 6 n 229 Sec 3 Changxing Rd Luzh U Dist laoyuan City 338 Taiwan RCC Always atthe forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw oo www bestek tw e Table of Content COPAC EE 2 ee Te EE 2 FOC SMG OS hR rlu ON E S AN 2 E gel aero ee T ener ea a en Sense a eee ane ae one ee ae eee eee ane ee eee ee ee eee 3 SAIS Se ge YI eee UO T 3 KAT ME E 4 Stein e Te BE 4 TIDE O og E 5 Chapter 1 General Information n N B ae TT sen carrey oaracnstecanccoasts nce tains ta ca tae nae nessdinn E gana sannoeTiornioneecns 7 e SIO CIM ANOS EE 8 A SV SUID Way OUR E 9 dL AP AC ACO EE Hate R GE 10 Chapter 2 Preparation 2 1 ROTORS VOU TEE 13 Zee PY Ca WO LE 13 SEELEN 14 EA COS SIE IV ee EE 15 DPC COS se a RE 16 LOA ef T WEE 17 2 7 Installing Wireless Module amp Antenna sss sees eee eee eee 18 EEAO NE IME EE 20 SAHT alne ATADO M ore E E E OEE E A NE NEE 21 Chapter 3 Operation SSC Turune On TNE SYAEIN ee 23 3 2 Installing Operating System amp Drivers 24 3 Understanding LED MONG at e CN 25 Chapter 4 BIOS Setup LENCE Di an A TEA E E E A EAE E EE N EE E AAEE 28 Dy OU AE EE 28 A CONTA E 28 AA Te EN ET E 29 RHI e Uee e Ty OPM EE 30 AVG CMO SOU IV ETT 32 G Ne VNC OO dn EE 34 AO WMO SOC MENG See 35 EE MN SS ad ege 36 Chapter 5 Auxiliary Information BGP IO Pe Sia itl EE eebe 39 L2 VDT aT CTT ee TTT 40 Cen
5. orm GPO26 GPOZ7 IO base address AOOh BitO GPI20 Bit1 GP 121 Bit2 GP 122 Bit3 GP 123 Bit4 GPO24 Bits GPO25 Bit6 GPO26 Bit7 GPO27 1 Read Write GPIO data by I O port A04h PIN Ee No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Age at tie tevelvant ai iniii TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 39 oo www bestek tw e 5 2 WDT Programming Guide p ITE8783F WatchDog Programming Guide SetupWDT PROC mov dx 2eh mov al 0087h out dx al nop nop mov al Olh Out dx al nop nop mov al 55h out dx al nop nop out dx al Write operations to special address port 2E for entering MB PnP Mode mov al 07h out 2eh al mov al 07h Select logical device for Watch Dog Out Zih al rer SetupWDT ENDP TimeBaseWDT PROC mov al 72h out 2eh al mov al 10h Set WDT reset upon PWROK or al 80h Here set 80h for second set 00h for minute Out Zin al ret TimeBasewDT ENDP No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R 0 C Absa tt te deefe steet TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 40 oo www bestek tw e TimeCountWDT PROC mov al 73h WDT Time out register out 2eh al mov al O3h Here Set count 3 out 2fh al ret TimeCountWDT ENDP EXLtSetup PROC mov al O2h out 2eh al mov al O2h Out zi al rer ExitSetup ENDP
6. City 338 Taiwan R O C jeresi O NA TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 12 oo www bestek tw e 2 1 Before You Begin A stable and clean working environment are essential Dust and dirt can get into components and cause a malfunction Use containers to keep small components separated Adequate lighting and proper tools can prevent you from accidentally damaging the internal components Most of the procedures that follow require only a few simple tools including the following e A Philips screwdriver Aflat tipped screwdriver e Aset of jewelers Screwdrivers e Agrounding strap e An anti static pad Using your fingers can disconnect most of the connections It is recommended that you do not use needle nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors Before working on internal components make sure that the power is off Ground yourself before touching any internal components by touching a metal object Static electricity can damage many of the electronic components Humid environment tend to have less static electricity than dry environments A grounding strap is warranted whenever danger of static electricity exists 2 2 Precautions Computer components and electronic circuit boards can be damaged by discharges of static electricity Working on the computers that are still connected to a power supply can be extremely dangero
7. in non volatile battery backed up CMOS RAM that saves this information even when the power is turned off When the system is turned back on the system is configured with the values stored in CMOS With easy to use pull down menus you can configure such items as Hard drives diskette drives and peripherals e Video display type and display options e Password protection from unauthorized use Power management features When to Run BIOS This program should be executed under the following conditions When changing the system configurations When a configuration error is detected by the system and you are prompted to make changes to the Setup program When resetting the system clock When setting the CPU clock speed so that it automatically runs either fast or slow e Whenredefining the communication ports to prevent any conflicts When making changes to the Power Management configuration When changing the password or making other changes to the security setup Normally CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM whenever the CMOS RAM loses power or when the system features need to be changed When to Update BIOS In the event that new features are released and a BIOS update is required you will need to update your BIOS on your own with the help of an appropriate guide a reference tool and some command files for the job Please seek for help f
8. such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis If a wrist strap is unavailable establish and maintain contact with the system chassis throughout any procedures requiring ESD protection Dax ea i A TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw oo www bestek tw e Safety Measures 7 EN o e e ze SE To avoid damage to the system e Use the correct AC input voltage range To reduce the risk of electric shock e Unplug the power cord before removing the system chassis cover for installation or servicing After installation or servicing cover the system chassis before plugging the power cord Battery e Danger of explosion if battery incorrectly replaced e Replace only with the same or equivalent type recommend by the manufacturer e Dispose of used batteries according to local ordinance Before Using the e me e me me Before using the system prepare basic system components If the system comes as a barebone that is none of the key components including processor memory and hard drive has been pre installed as part of your purchase you will need to at least ensure a compatible counterpart is located and installed You will also need a few external system peripherals intended for the use of the system a common pool with at least a keyboard a mouse
9. 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw oo www bestek tw e 1 2 Specifications Form Factor Construction System Drive Bays Cooling Connectivity Expansion Slots Environment No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C FAX 886 3 324 9777 TEL 886 3 324 9700 Material Dimension W x D x H Color Certification Processor Memory Power SATA HDD CFast Communication Front I O Rear I O Rear Access Operating Temperature Storage Temperature Operating Humidity Storage Humidity Shock Protection Vibration Protection Proprietary Wall Mount Chassis Aluminum 185 W x 131 D x 54 H mm Silver amp Red CE FCC Intel Atom Cedarview D2550 Dual Core Processor 1x DDR3 SO DIMM Slot up to 4GB 12 28Vdc Optional 12Vdc Power Adaptor 1 2 5 1x External Accessible True Fanless Design via Aluminum Housing Dual Intel 82574L PCle GbE Support WOL amp PXE 1x ATX Power Switch 1x Power LED 1x HDD LED 4 x COM Ports Two RS232 422 485 2x USB 2 0 Ports 2x Audio Jacks 2x Antenna Outlets 2x RJ45 LAN Ports 4 x USB 2 0 Ports 1x HDMI 1x DVI I Support VGA via Cable 1x 2 pin Power Input Support 10 28Vdc 1x External Screwed Type CFast Socket 1x miniPCle Slots for Half sized and Full sized Adaptor 5 55 C 20 80 C 0 90 0 90 HDD 20G CFast 50G Random 0 5Grms Sinusoidal 0 5Grms a T
10. 324 9777 EMAIL sales bestek tp com tw 36 emm www bestek tw e Save as User Defaults To use the current configurations as user default settings for the BIOS select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes Restore User Defaults To restore the BIOS to user default settings select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes Boot Override To bypass the boot sequence from the Boot Option List and boot from a particular device select the desired device and press lt Enter gt Launch EFI Shell from filesystem device To launch EFI shell from a filesystem device select this field and press lt Enter gt G Always at the forefront of innovation No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 37 oo www bestek tw d 6 No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C a mariait NA TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 38 o _ www bestek tw e 5 1 GPIO Programming Guide Digital I O Digital Input Output pins are provided for custom system design This appendix provides definitions and its default setting for the Digital I O pins in the NISE 104 The pin definition is shown is the following table ea mu Dosen es ore ve
11. Fanless System rEB 1 201 O NSSS lt Fang i e a A a CH User Manual O www bestek tw e Copyright This publication contains information that is protected by copyright No part of it may be reproduced in any form or by any means or used to make any transformation adaptation without the prior written permission from the copyright holders This publication is provided for informational purposes only The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose The user will assume the entire risk of the use or the results of the use of this document Further the manufacturer reserves the right to revise this publication and make changes to its contents at any time without obligation to notify any person or entity of such revisions or changes 2011 All Rights Reserved Trademarks All trademarks and registered trademarks of products appearing in this manual are the properties of their respective holders FCC and DOC Statement on Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and c
12. GA TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw co www bestek tw d G No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C jeresi O NA TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw oo www bestek tw e 1 1 Main Feature Processor Performance FEB 1251 is a fanless embedded wall mount system that is pre installed with Intel Cedarview D2550 Dual Core 1 86GHz processor bundled with integrated graphic and one SO DIMM slot supporting up to maximum 4GB DDR3 800 1066 All In One amp Compact Design The system boasts a considerably compact size of just 185x131x54mm with one DVI I one HDMI dual gigabit RJ45 network four COM ports six USB 2 0 and one CFast all available on the built in embedded board therein the TCO Total Cost of Ownership can be minimized The provision of wide range DC power input and the true fanless feature has made the system a perfect controller for FA and MA where a variety of different power sources such as 12 19 24Vdc are available List of Key Features Onboard Intel Atom D2550 1x HDMI 1x DVI I Output Dual Intel Gigabit LAN Ports 2x RS 232 2x RS 232 422 485 6x USB 2 0 Ports 1x External CFast Socket 1x miniPCle Slot Two Antenna Outlets 10 28Vdc Wide Range Power Input No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan ROC Aber at the forefront of innovation TEL 886 3
13. No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Absa tt te deefe steet TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 41
14. an radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables must be used in order to comply with the emission limits Cen a l TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw oo www bestek tw e Warranty 1 Warranty does not cover damages or failures that are raised from misuse of the product inability to use the product unauthorized replacement or alteration of components and product specifications 2 The warranty is void if the product has been subject to physical abuse improper installation mo
15. ave Changes and Exit To save the changes and exit the Setup utility select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes You can also press lt F4 gt to save and exit Setup Discard Changes and Exit To exit the Setup utility without saving the changes select this field then press lt Enter gt You may be prompted to confirm again before exiting You can also press lt ESC gt to exit without saving the changes Save Changes and Reset To save the changes and reset select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes Discard Changes and Reset To exit the Setup utility without saving the changes select this field then press lt Enter gt You may be prompted to confirm again before exiting Save Changes To save changes and continue configuring the BIOS select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes Discard Changes To discard the changes select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes to discard all changes made and restore the previously saved settings Restore Defaults To restore the BIOS to default settings select this field then press lt Enter gt A dialog box will appear Confirm by selecting Yes No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Alvays at the dere of innovation TEL 886 3 324 9700 FAX 886 3
16. can to be found in the detected drive list in the section of IDE Configuration In the event that a particular SATA device is not detected and prompted in the device list hardly would the system boot from it Please turn off the system check or re apply the SATA cable and SATA power cable or re insert CompactFlash card to ensure an appropriate connection Always Mind the SATA Mode SATA controller is embedded in the Intel IO Controller Hub and shall run only in one single SATA mode at a time Two different modes are available IDE and AHCI Please ensure that a SATA mode has been selected for the installation and always use this particular mode to boot the operating system being installed Failed to boot the operating system with the correct mode would definitely run into system collapse While thus disaster occurs please re select a SATA mode to try again the advisability of such change so as to determine the mode being used at installation phase Procedures to load operating system 1 Please attach USB CD ROM or DVD ROM drive 2 Start or restart the system 3 Press del to go to BIOS setup menu 4 Choose to confirm SATA Controller status If it is enabled select a SATA mode and go to 6 5 If SATA Controller is disabled bring it up and reboot to allow a re detection of Hard Drives 6 Confirm if the Hard Drive has been detected by the prompt of it on the drive list 7 Scroll and choose to boot from optical devic
17. dification accidents or unauthorized repair of the product 3 Unless otherwise instructed in this user s manual the user may not under any circumstances attempt to perform service adjustments or repairs on the product whether in or out of warranty It must be returned to the purchase point factory or authorized service agency for all such work 4 We will not be liable for any indirect special incidental or consequential damages to the product that has been modified or altered Static Electricity Precautions It is quite easy to inadvertently damage your PC system board components or devices even before installing them in your system unit Static electrical discharge can damage computer components without causing any signs of physical damage You must take extra care in handling them to ensure against electrostatic build up 1 To prevent electrostatic build up leave the system board in its anti static bag until you are ready to install it Wear an antistatic wrist strap Do all preparation work on a static free surface Hold the device only by its edges Be careful not to touch any of the components contacts or connections Avoid touching the pins or contacts on all modules and connectors Hold modules or connectors by their ends a gt ee Ze Important Electrostatic discharge ESD can damage your processor disk drive and other components Perform the upgrade instruction procedures described at an ESD workstation only If
18. e CD ROM or DVD ROM 8 Save and reboot the system to activate the change and start the installation 9 Upon reception of messages or instruction from Operating System CD or DVD please proceed with the rest of the work as installer instructs Loading Extra Driver Files Some challenges might occur during the installation as if the issue of no Hard Drive detected where extra driver files are needed This is mostly found when AHCI or RAID mode is selected in operating systems such as Windows XP where a USB floppy drive loaded with SATA driver should be prepared and attached on USB port and at the prompt of such a message please press F6 key while being asked to do so to allow the installer integrate the driver file from floppy drive Windows 7 or above apparently do not seem to come with such an issue against the onboard SATA Controller and hence no extra driver should be needed On completion of the installation of operating system such as Microsoft Windows please find the driver CD in the enclosed accessory bag and proceed with driver files installation in the sequence as INF Chipset VGA LAN and Audio If some driver updates are available by Windows Update please accept the updates when prompted Dax Sc T a No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan ROC Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 24 oo www bes
19. ek tp com tw 29 oc www bestek tw 4 5 The Advanced Menu gt The Advanced menu allows you to configure your system for basic operation Some entries are defaults required by the system board while others if enabled will improve the performance of your system or let you set some features according to your preference Aptio Setup Utility Copyright C 2011 America Megatrends Inc Launch Lan PXE OpROM Disabled Launch Lan PXE OpROM Disabled Enabled Launch LAN1 2 PXE OpROM Enables or disables the boot option for legacy network devices connected to LAN1 and LANZ CPU Configuration Hyper Threading Enable Disable CPU Hyper Threading Execute Disable Bit This field is used to enable or disable execute disable bit When this field is set to Disabled it will force the XD feature flag to always return to 0 XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS Windows Server 2003 SP1 Windows XP SP2 SuSE Linux 9 2 RedHat Enterprise 3 Update 3 Limit CPUID Maximum The CPUID instruction of some newer CPUs will return a value greater than 3 The default is Disabled because this problem does not exist in the Windows series operating systems If you are using an operating system other than Windows this problem may occur To avoid this problem enable this field to limit the return value to 3 or lesser than 3 No 6 Ln 229 Sec 3 Changxing Rd Luzhu D
20. ist Taoyuan City 338 Taiwan R O C Alvays at the dere of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 30 oo www bestek tw e IDE Configuration SATA Controller Enable Disable SATA Controller Configure SATA as e IDE This option configures the Serial ATA drives as Parallel ATA storage devices e AHCI This option allows the Serial ATA devices to use AHCI Advanced Host Controller Interface Super I O Configuration Serial Port Enable Disable Serial Port Device Setting Select I O Address and IRQ for Serial Port Onboard Serial Port 1 Mode Select Serial Port 1 operation mode from RS 232 RS 422 RS485 or RS 485 AUTO Onboard Serial Port Max Baud Rate Select Serial Port baud rate from 115200 and 921600 No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan ROC Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 31 oo www bestek tw e 4 6 The Chipset Menu Pr Aptio Setup Utility Copyright C 2011 America Megatrends Inc gt Host Bridge Host Bridge IGFX Boot Type This field is used to configure which video device will be activated during POST This has no effect if external graphics present The options are CRT DVI and CRT HDMI Please refer to the following table for BIOS setting and Display Output combination at POST mode However there is no such limitation at Window
21. mpt Timeout This section configures the number of seconds to wait for the setup activation key Quiet Boot When Enabled the BIOS will shorten or skip some check items during POST This will decrease the time needed to boot the system GateA20 Active Configures the GateA20 function Option ROM Messages Configures the ROM message Interrupt 19 Capture When enabled it allows the optional ROM to trap interrupt 19 Boot Option 1 2 This field is used to adjust the boot sequence of the system Boot Option 1 is the first boot device that the system will boot from next will be 2 and so forth No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the drett of ianevaiien TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 34 co www bestek tw e 4 8 The Security Menu p Aptio Setup Utility Copyright C 2011 America Megatrends Inc Administrator Password Administrator Password Sets the administrator s password User Password Sets the user s password Sal G No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 35 co www bestek tw e 4 9 The Save amp Exit Menu 15 The Save amp Exit Menu P Aptio Setup Utility Copyright C 2011 America Megatrends Inc Save Changes and Exit S
22. ow lists all the function keys for the navigation in the BIOS setup menu Function Key Tab F1 General Help a F1 F2 F3 To exit the Help Window press lt F1 gt or lt Esc gt No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 laiwan R O C Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 28 co www bestek tw 4 4 The Main Menu 4 4 The Main Menu f Aptio Setup Utility Copyright C 2011 America Megatrends Inc Intel RC version Figure 4 1 BIOS Setup Utility Main Menu Intel RC Version Displays the Intel Reference Code version System Date The date format is lt day gt lt month gt lt date gt lt year gt Day displays a day from Monday to Sunday Month displays the month from January to December Date displays the date from 1 to 31 Year displays the year from 1999 to 2099 System Time The time format is lt hour gt lt minute gt lt second gt The time is based on the 24 hour military time clock For example 1 p m is 13 00 00 Hour displays hours from 00 to 23 Minute displays minutes from 00 to 59 Second displays seconds from 00 to 59 Access Level Displays the access level of the current user in the BIOS No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the drett of ianevaiien TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales best
23. rcle or press and hold for 4 seconds to reach that goal However in most occasions without such abrupt event as stated above simply press once on the Power Switch to turn on the system Power LED The power switch comes with a built in LED to be used as power LED which shall come lit constant ON at system start HDD LED The HDD LED can be found above the power switch and shall blink in the wake of storage activity such as SATA drive or CompactFlash First screen amp Optimal BIOS Setting Once the system successfully boots up it shall activate display signal on monitor disclosing some system information as checkpoints for debugging thereafter users are encouraged to bring up BIOS setup menu to at least load the optimal BIOS setting as the first thing to do at power on Please refer to the BIOS section for substantial details Sal S Always at the forefront of innovation No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan ROC TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 23 oo www bestek tw e 3 2 Installing Operating System amp Drivers Confirm the Hard Drive List The system is designed to allow booting from a variety of internal devices including USB pen drive SATA drive and CompactFlash drive etc Given the tiny footprint and slow performance of USB pen drive SATA drive and CompactFlash are more prevailing devices to carry operating system and
24. rocedures 1 Turn off the system and find the CFast socket at the front panel AMAMSSSSSSSS SS HII AMSSSSSSSSSS SS IIE 2 Remove the two screws that hold the cover plate 3 Add or replace the CFast card 4 Restore the cover plate and resume the screws back to their positions Please always power off the system before adding or removing CFast card No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 17 www bestek tw o aaaaaaaaaaaaaaaaasmssli i 2 7 Installing Wireless Module amp Antenna To add Wireless Module 1 Please locate the miniPCle Slot on the embedded board 2 Add Wireless module onto the slot ensuring that the golden finger goes into the slot first Wireless LAN Module Mini PCI Express Slot Mini PCI Express Slot 3 Push the module down and secure the module with two screws Mounting Screws Note If it is full size module please remove this bracket Sal S Always at the forefront of innovation No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R 0 C TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 18 co www bestek tw To add Wireless Antenna 1 Find the two antenna cut out with protection covers 2 Remove the two covers Antenna Hole Covers
25. rom your local dealer or send your request to our technical support department Sal No 6 Ln 229 Sec 3 Ch a ng xing Rd Luzh U Dist Taoyu a n City 338 Taiwa n d R O C Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 2 oo www bestek tw e 4 1 Entering Setup When the system is powered on the BIOS will initiate the Power On Self lest POST routines These routines perform various diagnostic checks If an error is encountered the error will be reported in one of two different ways If the error occurs before the display device is initialized a series of beeps will be transmitted If the error occurs after the display device is initialized the screen will display the error message Powering on the computer and immediately pressing lt Del gt allows you to enter Setup Another way to enter Setup is to power on the computer and wait for the following message during the POST TO ENTER SETUP BEFORE BOOT PRESS lt CTRL ALT ESC gt OR lt DEL gt KEY Press the lt Del gt key or press the lt Ctrl gt lt Alt gt and lt Esc gt keys to enter Setup 4 2 Getting Help The online description of the highlighted setup item is displayed at the right pane of the menu at all time Press F1 to pop up a small help window that lists allthe function keys and its use To exit the Help Window press lt F1 gt or lt Esc gt 4 3 Control Keys The table bel
26. s mode as graphic driver will help to handle all display output Connected Monitor Type BIOS setting HDMI only DVI HDMI HDMI only CRT HDMI HDMI HDMI DVI via Y cable DVI DVI HDMI VGA via Y cable CRT HDMI CRT HDMI HDMI VGA via Y cable VGA VGA Fixed Graphics Memory Size This field is used to configure the memory size of the fixed graphics the options are 128MB and 256MB No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Always at the drett of ianevaiien TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 32 emm www bestek tw e South Bridge Azalia Controller This section disables Azalia or enables HD Audio SMBus Controller This section is used to configure SMBus High Precision Timer This section is used to configure High Precision Event Timer Restore AC Power Loss This field is used to configure the AC power state when power is restored after power failure the options are Power Off and Power On Sal G Always at the forefront of innovation No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 33 oc www bestek tw e 4 7 The Boot Menu 17 The Boot Menu P Aptio Setup Utility Copyright C 2011 America Megatrends Inc Boot Option 1 SATA SM TS4GCFXS500I Boot Option 1 UEFI Pretec 01GB 2 00 Disabled Setup Pro
27. side away from the cover edge to reserve space for adding cables later on 2 Flip over the cover and find the four screw holes find the four hard drive screws enclosed in the accessary bag and add them to secure the 2 5 drive on the bottom cover SATA Drive a Cover 3 Find the 2 5 drive cable from the enclosed accessory bag and attach this cable to the drive itself and also the SATA Connector CN6 and SATA Power Connector J4 on the embedded board SATA Data Power Cable SATA Drive 4 Add SATA signal cable and SATA power cable to complete the work No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Alvays at the toreivent of innoveiian TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 16 oo www bestek tw e 2 6 Accessing CFast Card CFast instead of CompactFlash As stated above significant differences of CompactFlash and CFast are literally defined by their respective interfaces though the very resemblances can merely be indistinctly differentiated Perfect Solution for Data Drive CFast card runs on SATA interface exactly the same way as any SATA device only it comes with smaller form factor and is a pure flash device with no spindle at all boasting outstanding stability and SATA performance The friendly access from the rear side with no need to open up the bottom cover has undoubtedly made it a perfect solution as SATA data drive P
28. side down 2 Remove the 4 screws as indicated in the places below 3 Securing the screws is essential for they would be re used for the restoration of the top cover after all preparation procedures are completed No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Absa tt te deefe steet TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 14 D www bestek tw e 2 4 Accessing Memory Please locate the DDR3 SODIMM slot as indicated below To install SO DIMM 1 Make sure the Key on Memory module and SO DIMM slot are perfectly matched and add slowly the RAM module into the SO DIMM slot 2 Push the RAM module downwards to seat it firmly Make sure the RAM module is snapped perfectly by the slot and the two handles are restored back to close position automatically If not press the handles to close position 3 Toremove the Memory module please push the handles outwards and the memory module will be automatically disengaged No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C Alvays at the toreivent of innoveiian TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 15 co www bestek tw e 2 5 Accessing 2 5 Drive Procedures 1 Please locate the 2 5 Drive Bay on the bottom cover as indicated below and add the 2 5 Drive Note the I O side of the hard needs to be on the
29. tek tw e 3 3 Understanding LAN Indicators Activity LED The left LED is LAN Port Activity LED with three different indication status 1 Constant Yellow Network is connected 2 Blinking Yellow Network activity is on going 3 Off Network is not connected LAN Speed LED The right LED is LAN Port Speed LED with three different speeds 1 Amber 1000 Speed 2 Green 100 Speed 3 Off 10 Speed Summary Table LED Color State Description Yellow On LAN linked Yellow Blinking LAN accessing Off Off No LAN linked RJ45 NIC Linkage Left Side Gigabit mode 100M mode 10M mode RJ45 NIC Mode Right Side No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 laiwan R O C Always at the forefront of innovation TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 25 oo www bestek tw d 6 No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C a mariait NA TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 26 O www bestek tw e About the BIOS The BIOS Basic Input and Output System Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs It is a ROM based configuration utility that displays the system s configuration status and provides you with a tool to set system parameters These parameters are stored
30. us Follow the guidelines below to avoid damage to your computer or yourself Always disconnect the unit from the power outlet whenever you are working inside the case If possible wear a grounded wrist strap when you are working inside the computer case Alternatively discharge any static electricity by touching the bare metal chassis of the unit case or the bare metal body of any other grounded appliance e Hold electronic circuit boards by the edges only Never touch the components on the board unless it is necessary to do so Do not flex or stress the circuit board Leave all components inside the static proof packaging that they shipped with until they are ready for installation Use correct screws and do not over tighten screws Sal Always at the forefront of innovation No 6 Ln 229 Sec 3 Changxing Rd Luzhu Dist Taoyuan City 338 Taiwan R O C TEL 886 3 324 9700 FAX 886 3 324 9777 EMAIL sales bestek tp com tw 13 oo www bestek tw e 2 3 Open Up Bottom Cover This is the first step of all to proceed with if you are to install or change a hard drive a memory module or a wireless module etc t is not necessary to open up the bottom cover if it is to add remove swap a CFast card as another rear accessible cover has been designed for this purpose Please refer to the CFast section for details 1 Please shut down the unit remove the power cable and place the unit on a clean surface up
Download Pdf Manuals
Related Search