Geoision IP cameras manual
Contents
1. Thread the cable through the conduit entry at the bottom of the back cover 41 e GeoVision 10 11 12 42 Follow step 1 in the Hard Ceiling Mount section to secure the camera body with inner housing Connect the network and power cables to the camera See 4 4 Connecting the Camera in the Quick Start Guide Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide Follow steps 9 to 10 in the Hard Ceiling Mount section to adjust the angle focus and zoom of the camera Follow steps 11 to 12 in the Hard Ceiling Mount section to secure the thread lock and the housing cover a Vandal Proof IP Dome 4 4 Connecting the Camera The following diagram shows the data cable of the Vandal Proof IP Dome There are two ways to supply power to the camera e Use a Power over Ethernet PoE adapter to connect the camera to the network and the power will be provided at the same time e Use the supplied 2 pin terminal block and power adapter 4 4 1 Wire Definition No Wire Color Black thick Black thin Red Orange Brown Yellow Red Green Black o ONTO IAIA JO Mw lt Shielding ground DC 12V AC 24V DC 12V AC 24V Digital in oragne Digital out brown Ground yellow Audio in red Audio out green TV out Ethernet PoE Definition Shielding Ground DC 12V AC 24V DC 12V AC 24V Digital In Digital o2. lt mo na F 7 i Ma vr Vision GF tee 4 P I i l Quick Start Guide GV IP Camera H 264 e GeoUision 2011 GeoVision Inc All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of GeoVision Every effort has been made to ensure that the information in this manual is accurate GeoVision Inc makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein Features and specifications are subject to change without notice GeoVision Inc 9F No 246 Sec 1 Neihu Rd Neihu District Taipei Taiwan Tel 886 2 8797 8377 Fax 886 2 8797 8335 http www geovision com tw Trademarks used in this manual GeoVision the GeoVision logo and GV series products are trademarks of GeoVision Inc Windows and Windows XP are registered trademarks of Microsoft Corporation January 2011 Contents IC iii Ki E ARRE GO ra A vi Note for ConnectingtoGV System vii Note for Adjusting Focus and Zoom viii Ts DOZ GAGE mmm 1 EM AG lt a ES A ate 1 A eee eee AM 2 1 3Accessoryinstallation 5 1 3 1 C Mount LENSOS akad al el Ae aaa 5 1 3 2 Infrared I
3. Adjusts the focus of the camera Absorbs moisture in the camera body 31 te GeoUision 4 3 Installation The Vandal Proof IP Dome is designed for outdoors There are three ways to install the Vandal Proof IP Dome hard ceiling mount in ceiling mount and wall pendent mount 4 3 1 Hard Ceiling Mount 1 Unpack the camera package and take out the camera body Unscrew the housing cover ay A C GeoVision 32 Unscrew thread lock Unscrew the inner housing Take out the camera body 4 Vandal Proof IP Dome 33 e GeoUision 2 3 4 34 Mark the position of four screw holes on the desired installation location and drill holes in the marked locations Drill the ellipse part if you wish to put the wires through it Insert the screw anchors to the 4 holes on the ceiling Secure the back cover to the ceiling with 4 ceiling screws Follow step 1 to secure the camera body with inner housing Thread the cable through the conduit entry at the side of the back cover Alternatively pass the wires through the ellipse hole at the bottom of the back cover Connect the network and power cables to the camera See 4 4 Connecting the Camera in the Quick Start Guide 4 Vandal Proof IP Dome 8 Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide 9 Adjust the camera to a desired angle as illustrated below Tip The 3 axis mechanism offer
4. Reboot Do you wish to reboot now te GeoVision 10 2 Directly on the Camera GV BX110D 1 2 3 70 Unplug the power cable and the network cable to start Press and hold the default button on the back panel of the camera Default button Power on the camera using the power cable or PoE cable The status LED on the front panel of the camera turns red e Status LED Wait until the status LED turns off This may take about 10 seconds Soon after the status LED turns off it turns red again and a clicking sound appears Then you can release the default button and the process of loading default values is completed KI Restoring to Default Settings GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 1 Unplug the power cable and the network cable to start 2 Press and hold the default button on the back panel of the camera o e lili CP e Micro video Out 9 3 my e Default button G 12V Auto Iris 4 LAN POE 3 Power on the camera using the power cable or PoE cable The status LED on the front panel of the camera turns on and then off twice This may take about 30 seconds Status LED 4 Release the default button and the process of loading default values is completed 71 e GeoUision Mini Fixed Dome 1 2 3 Unplug the network cable to start Unscrew the camera s cover Press and hold the default button Default button
5. Installing the Sun Shield Cover in the Quick Start Guide 3 3 1 Adjusting the Angles The Bullet Camera is designed to be adjustable in three shafts Tip The three shafts are designed to offer easy and flexible ceiling wall mount installation First Shaft You can adjust the camera body by 360 degrees to the right or the left 1 Unscrew the panning lock screw with the screw adjuster Panning Lock Screw Screw Adjuster 20 Bullet Camera 2 Adjust the angle of camera body to the right or the left and fasten the panning lock screw 0 360 La Second Shaft You can adjust the camera body up and down by 90 112 5 135 157 5 or 180 degrees by using the gears inside the camera body and the camera base 1 Unscrew the tilting lock screw with the screw adjuster _ i Tilting Lock Screw Screw Adjuster 2 Hold the camera body and move the camera base to the right to separate the camera gears Move the Camera Base to the Right Camera Gears 21 e GeoUision 3 Adjust the angle of camera body to 90 112 5 135 157 5 or 180 degrees Then move the camera base to the left to combine the gears sa m 180 157 5 135 112 5 90 4 Fasten the tilting lock screw Third Shaft You can adjust the camera base by 360 degrees 1 Unscrew the base fixing screw with the screw adjuster 22 Bullet Camera 2 Adjust the angle of camera base and fasten the base
6. LP 45 VARCO ZEE EEE 46 reer ng A MEME EMME er e 48 5 3 1 Hard Ceiling MY PM 48 5 3 2 VWieali SurfaceMount Bl eee 52 5 gaia ls BE ngentiMaunfl sm EMA RE R 59 5 4 Connecting the Camera ii 55 0 CURE LE GaGa ain 57 6 1 K iri ayol CAC iaia 57 O OUENIEW reale 58 6 3 Istalla ON ca AR dea 59 6 4ConnectinggtheCamera 60 7 AccessingtheCamera 000 000 61 1S5ysteemReguirement 61 2AssigninganIPAddress 62 5 The Web Interface coca niwie 65 9 Upgrading System Firmware iii 67 10 RestoringtoDefaultSettings 69 10 1 Using the Web Interface aa aa aa aa aa aaa aaaaaaaaacaania 69 10 2DirectliyontheCamera 70 Introduction Welcome to the GV IPCam H 264 Quick Start Guide In this quick guide you will find information on the installation and basic configurations of the Box Camera Mini Fixed Dome Bullet Camera Vandal Proof IP Dome Fixed IP Dome and Cube Camera Camera Lens GV BX110D 1 3 M H 264 D N Varifocal Box IP Cam Lens Varifocal 1 3 M H 264 Low a Lux D N Box IP Cam 2 M H 264 D N Box IP Cam Auto Iris IR GV BX220D 0 f 2 8 8 5 mm
7. 1 Put the supporting rack on the desired location and make marks for screw anchors 2 Drill the marks and insert the screw anchors Secure the supporting rack onto the wall using the supplied screws 4 Screw the camera onto the supporting rack and fasten the indicated screw 5 Adjust the angles of the camera and fasten the indicated screw 59 te GeoVision 6 4 Connecting the Camera Use a standard network cable to connect the camera to your network Connect power by plugging the supplied power adapter to the DC jack 3 The status LED of the camera will be orange Then you can set the IP address for the unit See 7 Accessing the Camera in the Quick Start Guide 60 7 Accessing the Camera 7 1 System Requirement To access the Box Camera Mini Fixed Dome Bullet Camera Vandal Proof IP Dome Fixed IP Dome and Cube Camera through the Web browser ensure your PC connects to the network properly and meets this system requirement e Microsoft Internet Explorer 7 x or later Note For the users of Internet Explorer 8 additional settings are required For details see Appendix B in GV IPCam H 264 User s Manual on the software CD e GeoUision 7 2 Assigning an IP Address Designed for use on the network the Box Camera Mini Fixed Dome Bullet Camera Vandal Proof IP Dome Fixed IP Dome and Cube Camera must be assigned an IP address to make it accessible 1 62 Open your web browser and t
8. GV BX110D as illustrated below C mount lens adapter e GeoUision GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 The supplied lens rings for GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 include 3 sizes in thickness e 0 188 mm transparent color x 2 e 0 125 mm black color with a glossy surface x 2 e 0 254 mm black color with a matt surface x 2 Note These lens rings are specially designed for varifocal models of GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 Besides the supplied 6 units each varifocal model has already been installed with a 0 188 mm lens ring Lens ring I e GeoUision e GeoVision il Box Camera 1 3 2 Infrared Illuminators GV IR LED GV IR LED T2 1 Connect the infrared illuminator to the terminal block on the camera See I O Terminal Block Box Camera chapter GV IPCam H 264 User s Manual on the software CD or GV IR LED User s Manual Access the Web interface of the camera GeoVision Inc IP Camera 1 3M Windows Internet Explorer DER Ge EJhttp f192 168 0 36 ssi cgi Login htm el _ w he Geovision Inc IP Camera 1 3M 27D z Tools A e GeoVision IP CAMERA SETUP Login Password s Internet Select Video and Motion select Video Settings select Streaming 1 and set the IR Check Function option to be Trigger by Input for GV IR LED or Trigger
9. H 264 Cube Fixed Cube Camera Camera GV CB220 Lens 2 MH 264 Cube Camera For a detailed users manual see GV IPCam H 264 User s Manual on the software CD e GeoUision Options Optional devices can expand your camera s capabilities and versatility Contact your dealer for more information Device Description GV IR LED GV PA191 PoE Adapter Wall Mount Bracket Housing Cover vi A mountable infrared LED device that improves image performance of Box Cameras under low light conditions Note that the GV IR LED is only compatible with GV BX110D and GV IR LED T2 is compatible with GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 The GV PA191 PoE adapter is designed to provide power and network connection to the cameras over a single Ethernet cable An L shaped bracket designed for wall mount installation of the Vandal Proof IP Dome and the Fixed IP Dome The housing cover is designed for Vandal Proof IP Dome to provide shielding to the camera Two types are available transparent and smoked Note for Connecting to GV System The GV IPCAM H 264 is designed to work with GV System a hybrid or digital video management system Note the following when GV IPCAM H 264 is connected to GV System 1 Normally the images are recorded to the memory card inserted in the Box Camera Bullet Camera Vandal Proof IP Dome Fixed IP Dome and Cube Camera Once the camera is connected to G
10. fixing screw site 3 3 2 Adjusting Lens and Inserting a Memory Card To adjust the camera s lens to produce a clear image and insert a memory card into the memory card slot 1 Loosen the camera s cover Camera s Cover 2 Remove the silica gel bag m a Silica Gel Bag 23 e GeoVision 3 Loosen the fixing screw Fixing Screw 4 Slightly pull out the camera module Loosen the Focus Screw or the Zoom Screw to rotate the lens right left to adjust focus or zoom Insert a micro SD SDHC card into the memory card slot Zoom Screw Memory Card Slot Focus Screw 5 Slightly push the camera module back and fasten the fixing screw 6 Replace a new silica gel bag to the camera module and fasten the camera s cover immediately IMPORTANT To prevent the lens from fogging up you must replace the silica gel bag every time you open the camera The gel bag loses its effectiveness when the dry camera is opened 24 Bullet Camera 3 3 3 Inserting the Sun Shield Cover After setting up the Bullet Camera now you can install the sun shield cover to the camera 1 Fasten the hexagon screws either on top or below the camera Hexagon Screws 2 Put the sun shield cover on top of hexagon screws Make sure to aim the rear hexagon screw at the edge of the sun shield cover s aperture for optimal sun shield performance 3 Fasten the Philips head screws with the plastic screw spacers Phil
11. the power cable or PoE cable 74 10 Restoring to Default Settings 4 When the status LED turns on and off twice release the default button and the process of loading default is completed This may take about 35 seconds Cube Camera 1 Unplug the power cable and the network cable to start 2 Use a pin to press and hold the default button on the panel MN 3 Power on the camera using the power cable 4 When the status LED turns on orange and off twice release the default button and the process of loading default is completed This may take about 35 seconds 75
12. 020 i 3 Click the Browse button to locate the firmware file img saved at your local computer 4 Click the Upgrade button to start the upgrade WARNING The interruption of power supply during updating causes not only update failures but also damages to the camera In this case please contact your sales representative and send your device back to GeoVision for repair 68 10 Restoring to Default Settings GeoVision periodically releases updated firmware on the website The new fir You can restore factory default settings through the Web interface or directly on the camera 10 1 Using the Web Interface 1 On the left menu of Web interface select Management and select Tools The Additional Tools dialog box appears 2 Click the Load Default button in the System Settings section e GeoUision Additional Tools Video and Motion inthis section you can set the additional tools VO Control Events and Alerts Host Settings gt Monitoring Recording Schedule In this section you can determine a hostname and camera name for identification Remote Viewlog Network Management gt Date and Time Apply Host Name GV BX120D GPS Maps Settings Storage Settings In this section you can see GV IPCAM firmware version Firmware Update User Account gt Log Information System Settings Restore to factory default settingsi Load Default Current chipset temperature inside camera is 4
13. 20D 0 220D 1 220D 2 220D 3 320D 0 320D 1 No 10 11 12 YENI Video Out Audio Out Audio In Name Video Out Memory Card Slot Audio Out Audio In I O Terminal Block Power LED Default LAN PoE DC 12V Port Auto ris Connector Microphone Status LED i PWR Logd Defpult Gli2v LANIPOE Description Connects to a portable monitor for setting the focus and angle of Box Camera during initial installation Inserts a micro SD SDHC card to store recording data Connects a speaker for audio output Connects a microphone for audio input Connects I O devices For details see O Terminal Block Box Camera chapter GV IPCam H 264 User s Manual on the software CD Indicates the power is supplied Resets all configurations to factory default See 10 Restoring to Default Settings later in the Quick Start Guide Connects to a 10 100 Ethernet or PoE Connects to power Plug the iris control cable to the connector Records the sounds Turns on when the unit is ready for use KT Box Camera 1 3 Accessory Installation 1 3 1 C Mount Lenses When you use a C mount lens it requires a certain distance from the camera s imaging chip otherwise it will not be possible to focus the lens Mount the supplied C mount lens adapter lens ring to the camera and then attach the lens onto the camera body GV BX110D Install the supplied C mount lens adapter to extend focal length for
14. 6 Adjust the camera to a desired angle as illustrated below Tip The 3 axis mechanism offers flexible and easy ceiling wall installation Pan adjustment 50 EB Fixed IP Dome Rotational Adjustment fam esi tila a as a T Focus Screw Zoom Screw 8 Secure the housing cover as shown in step 2 Remove the indicated part when necessary t ei Note Adjust the black mask inside the housing cover to make sure the camera view is not obscured 51 e GeoUision 5 3 2 Wall Surface Mount 52 E GeoVision Follow step 2 in the Hard Ceiling Mount section to remove the housing cover and take out the camera body Paste the supplied sticker onto a desired location on the wall Drill the three red dots and the ellipse mark only if you wish to run the wires into the wall Insert the short screw anchors and secure the camera and the mounting plate with three plate screws Connect the network and power cables to the camera See 5 4 Connecting the Camera in the Quick Start Guide Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide EB Fixed IP Dome 6 Follow steps 6 and 7 in the Hard Ceiling Mount section to adjust the angle focus and zoom of the camera 7 Follow step 8 in the Hard Ceiling Mount section to secure the housing cover 5 3 3 Wall Pendent Mount For the wall pendent mount installation you need to purchase the wall mo
15. F 1 4 1 3 CS Lens 2 M H 264 D N Box IP Cam Auto Iris IR GV BX220D 1 a Varifocal F 1 2 1 3 CS Lens AE 2 M H 264 D N Box IP Cam Auto Iris IR GV BX220D 2 nin F 1 3 1 3 CS Lens 2 MH 264 DIN Box GV BX220D 3 IP Cam Auto Iris IR f 2 8 12 mm F 1 4 1 3 CS Lens e GeoUision 3 M H 264 D N GV BX320D 0 Box IP Cam f3 1 8 mm Varifocal F 1 2 1 3 CS Lens Lens 3 M H 264 D N Box IP Cam GV BX320D 1 f 2 8 6 mm F 1 3 1 3 CS Lens 1 3 M H 264 Color SERRA Mini Fixed Dome 1 3 M H 264 IR SRDA Bullet IP Cam GV BL120D 1 3 M H 264 Low Varifocal Lux IR Bullet IP Cam Lens 2 MH 264 IR GV BL220D Bullet IP Cam 3 MH 264 IR GV BL320D Bullet IP Cam GV VD120D IK10 Transparent Cover Vandal GV VD121D Proof IP IK10 Smoked Cover Dome GV VD122D Transparent Cover GV VD123D Smoked Cover Varifocal 1 3 M H 264 Low Lens Lux IR Vandal Proof IP Dome GV VD220D IK10 Transparent Cover GV VD221D IK10 Smoked Cover 2 MH 264 IR GV VD222D Vandal Proof IP Transparent Cover Dome GV VD223D Smoked Cover Varifocal GV VD320D Lens Vandal Proof IP Dome IK10 Transparent Cover GV VD321D IK10 Smoked Cover 3 MH 264 IR GV VD322D Vandal Proof IP Transparent Cover Dome GV VD323D Smoked Cover 1 3 MH 264 Low GV FD120D Lux IR Fixed IP Fixed IP Varifocal Dome Dome Lens GV FD220D 2 M H 264 IR Fixed IP Dome ai 3 M H 264 IR I Fixed IP Dome GV CB120 1 3 M
16. IIUMINAtors i 7 1 4 Connecting the Camera iii 9 2 Mini Fixed Dome rr 13 2 1 Packip Ste RE RIR 13 2 2 Ove a e ee M VE T o 14 AN eg MM dE e PR G 15 2 4dAdjustingtheFocus 16 URI baia 17 1 e BSD znani eizo cer N 17 SPANO AIZ PA Z 18 320 pr he ME CAN EEE ME MY 19 3 3 1AdjustingtheAngles 20 3 3 2 Adjusting Lens and InsertingaMemoryCard 23 3 3 3 nsertingtheSun ShieldClover 25 3 4ConnectinggtheCamera 26 3 4 1 Wire Definition ii 26 3 4 2 Connecting the Power Cable sea aaaanai 27 3 4 3 Applying Waterproof Treatment n 27 te GeoVision 4 VandalProofiPDome 29 gt e e Ost MN p Eeee 29 42O veMWieW 31 BSB US eal AU OIA ROEE 32 4 3 1 Hard Ceiling Mount 32 4 3 2 In Ceiling MOUNt ee aaa aaa aaa aaa aaa aaaaaaaaaaaaaccaa na 37 4 3 3 Wall Pendent Mount ea aaaa aaa aaa aaa aaaaecanaaa 40 44ConnectingtiheCamer 43 4 4 1 Wire Definition i 43 4 4 2 Connecting the Power Cable 44 Pelo 45
17. IR by D N for GV IR LED T2 GV IR LED GeoVision wie 7 Video and Motion Live View Audio In Source Video Settings gt Streamingi Audio In Source Built in Microphone External Microphone gt Streaming2 gt Motion Detection TVOUT Privacy Mask gt Tampering Alarm gt Visual Automation gt VO Control gt Events and Alerts Monitoring Auto adjustment Start Recording Schedule gt Remote Viewlog Network Signal Format NTSC PAL Mechanical Iris Adjustment Special View Setting Additional functions for Live View DIN Auto O Black and White O Color IR Check Function Indoor Outdoor Triggered by Input Auto Iris Enable Disable gt Management Logout te GeoVision GV IR LED T2 e GeoVision Video and Motion Live View Video Settings Streaming2 gt Motion Detection Privacy Mask gt Tampering Alarm gt Visual Automation gt VO Control Events and Alerts gt Monitoring Recording Schedule gt Remote Viewlog gt Network gt Management gt Logout In this section you can set Watermark function C Enable TVOUT Signal Format NTSC PAL O Disable LED Control Ready LED Enable O Disable Special View Setting Additional functions for Live View DIN Auto O Black and White O Color IR Check Function off O On Trigger IR by DIN Auto Iris Enable Disable BLC off O
18. Software DVD e GV NVR Quick Start Guide te GeoUision 3 2 Overview Name Description Memory Card Slot Receives a Micro SD SDHC memory card Zoom Screw Holds the zoom lens in place Focus Screw Holds the focus lens in place Default Button Resets all configurations to factory default See 10 Restoring to Default Settings later in the Quick Start Guide 18 B Bullet Camera 3 3 Installation The Bullet Camera is designed for outdoor use and can be mounted on ceiling and wall 1 Slide the cable clamp to the camera base Cable Clamp 2 Install the Bullet Camera to the wall ceiling Lin t La ASA SA Te 3 Remove the protection sticker from the camera s cover 4 Connect the network and power cables to the camera See 3 4 Connecting the Camera in the Quick Start Guide 5 Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide 6 Adjust the angles of the camera body and the base Three shafts can be adjusted For details see 3 3 7 Adjusting the Angles in the Quick Start Guide 19 te GeoVision 7 Loosen the camera s cover adjust lens and focus and insert a micro SD SDHC card into the memory card slot See 3 3 2 Adjusting Lens and Inserting a Memory Card in the Quick Start Guide 8 Fasten the camera s cover Install the sun shield cover to the Bullet Camera For details see 3 3 3
19. V System for video management or the camera s Live View is accessed through the Web browser see 7 Accessing the Camera in the Quick Start Guide the recording to the memory card will be stopped and the recording will be taken control by GV System When the connection between the camera and GV System is interrupted the recording to the memory card will be resumed to back up the images on the camera 2 Once the camera is connected to GV System the resolution set on GV System will override the resolution set on the camera s Web interface You can only change the resolution settings through the Web interface when the connection to GV System is interrupted vii te GeoVision Note for Adjusting Focus and Zoom When adjusting the Focus and Zoom Screws on Box Camera Mini Fixed Dome Bullet Camera Vandal Proof IP Dome and Fixed IP Camera please do not over tighten the Focus and Zoom screws The screws only need to be as tight as your finger can do it don t bother using any tools to get them tighter Doing so can damage the structure of lens For example Zoom Screw Focus Screw PR Focus Screw gt i Zoom Screw Bullet Camera Fixed IP Camera viii 1 Box Camera 1 1 Packing List e Box Camera e Terminal Block e Fixed Focal or Varifocal Megapixel Lens e C mount Lens Adapter BX110D only e Lens Rings BX120D BX220D 0 220D 1 220D 2 220D 3 BX320D 0 320D 1 only e Video Out Wire B
20. X120D BX220D 0 220D 1 220D 2 220D 3 BX320D 0 320D 1 only e DC 12V Power Adapter e GV IPCAM H 264 Software CD e GV IPCAM H 264 Quick Start Guide e GV NVR Software DVD e GV NVR Quick Start Guide e GeoUision 1 2 Overview GV BX110D AUDID OUT AUCJO IN DEFAUL MINI SD VIDEO OUT Flashing Red and Green The camera is ready for use with network Lights Green Light ON Error occurs on the system a Box Camera No Name Description 1 Audio Out Connects a speaker for audio output 2 Audio In Connects a microphone for audio input Resets all configurations to factory default 3 Default See 10 Restoring to Default Settings later in the Quick Start Guide Memory Card Slot uo a micro SD SDHC card to store recording data Connects to a portable monitor for setting 5 Video Out the focus and angle of Box Camera during initial installation Connects I O devices For details see O Terminal Block Box Camera chapter 6 I O Terminal Block GV IPCam H 264 User s Manual on the software CD 7 LAN PoE Connects to a 10 100 Ethernet or PoE 8 DC 12V Connector Connects to power Reflects system status of the camera See 9 Status LED the table below 10 Microphone Records the sounds 11 Ml ei If the varifocal lens is in use plug the iris control cable to the connector Status LED Description Red Light ON The system powers on and succeeds to boot up connectivity e GeoUision GV BX120D 2
21. ct the camera to your network Optionally connect a speaker and an external microphone Optionally connect a monitor using a Video Out wire If your signal format is PAL configure the TV Out setting on its Web interface See TV Out setting in the Video Settings section Administrator Mode chapter GV IPCam H 264 User s Manual on the software CD Connect power using one of the following methods e plugging the supplied power adapter to the power port e using the Power over Ethernet PoE function and the power will be provided over the network cable The status LED of the camera will be on Then you can set the IP address for the unit See 7 Accessing the Camera in the Quick Start Guide 11 e GeoUision alarm shop 2 Mini Fixed Dome 2 1 Packing List e Mini Fixed Dome e Security Torx e Self Tapping Screw x 2 e Screw Anchor x 2 e GV IPCAM H 264 Software CD e GV IPCAM H 264 Quick Start Guide e GV NVR Software DVD e GV NVR Quick Start Guide te GeoVision 2 2 Overview 1 Default Button Lens Focus Fixed Screw Tilt Fixed Screw Built In Microphone O1 RB wW N _ Description Resets the GV MFD110 to factory default See 10 Restoring to Default Settings later in the Quick Start Guide Rotates the les right left to adjust focus Loosens the screw to adjust the lens Loosens the screw to adjust tilt angle Provides one way audio Network PoE Connection 14 Connects the Network cable
22. for power and Ethernet connection e Mini Fixed Dome 2 3 Installation The GV MFD110 is exclusively designed for ceiling mount Please make sure the installing site is shielded from rain and moisture 1 Take the Mini Fixed Dome and make 2 marks on the ceiling for screw anchors 2 Drill the marks and insert the screw anchors 3 Secure the Mini Fixed Dome to the ceiling with the self tapping screws Note Due to the compact design the camera can only be powered using PoE 15 te GeoVision 2 4 Adjusting the Focus Based on the live image adjust the camera s angle and focus by following the steps below To access live images see 7 Accessing the Camera in the Quick Start Guide 1 Unscrew the camera s cover 2 Loosen the focus fixed screw and rotate the lens clockwise or counterclockwise to adjust focus Loosen the tilt fixed screw and adjust the camera s tilt angle Focus Fixed Screw Tilt Fixed Screw 16 3 Bullet Camera 3 1 Packing List e Bullet Camera e Lens Megapixel and Built In 16 IR LEDs e Self Tapping Screw x 3 e Plastic Screw Anchor x 3 e Screw Adjuster x 2 e Sun Shield Cover Kit 1 Sun Shield Cover 2 Philips Head Screws 2 Plastic Screw Spacers and 2 Hexagon Screws included e Silica Gel Bag x 2 1 is already placed inside the camera module e 3 Pin Terminal Block e DC 12V Power Adapter e GV IPCAM H 264 Software CD e GV IPCAM H 264 Quick Start Guide e GV NVR
23. gt Power on the camera using the network cable Wait until the network status LED turns off This may take about 40 seconds Soon after the network status LED turns off release the default button The process of loading default values is completed Bullet Camera 72 Unplug the power cable and the network cable to start Loosen the camera s cover and remove the Silica Gel Bag Unscrew the Fixing Screw and slightly pull out the camera module Fixing Screw KI Restoring to Default Settings 4 Press and hold the Default button for 50 seconds while plugging the power cable Default Button 5 Release the default button and the process of loading default values is completed Slightly push the camera module back and fasten the Fixing Screw Replace a new Silica Gel Bag and fasten the camera s cover immediately Vandal Proof IP Dome 1 Unplug the power cable and the network cable to start 2 Use a pinto press and hold the default button on the inner housing Default 3 Power on the camera using the power cable or PoE cable 73 te GeoVision 4 When the status LED turns on and off twice release the default button and the process of loading default is completed This may take about 30 seconds Status LED Fixed IP Dome 1 Unplug the power cable and the network cable to start 2 Use a pin to press and hold the default button on the panel Default 3 Power on the camera using
24. ips Head Screw z a Plastic Screw Spacer 25 e GeoUision 3 4 Connecting the Camera The following diagram shows the data cable of the Bullet Camera There are two ways to supply power to the camera e Use a Power over Ethernet PoE adapter to connect the camera to the network and the power will be provided at the same time e Use the supplied 3 pin Terminal Block and power adapter For details see Connecting the Power Cable in the following section Digital In Red DC 12V AC 24V Brown a Digital Out Orange DC 12V AC 24V Black GND Yellow Audio In Red Ethernet PoE Audio Out Green 3 4 1 Wire Definition No Wire Color Definition 1 Red Digital In 2 Brown DC 12V AC 24V 3 Orange Digital Out 4 Black DC 12V AC 24V 5 Yellow Ground 6 Red Audio in 7 Green Audio out 26 Bi Bullet Camera 3 4 2 Connecting the Power Cable 1 Insert the black wire of the Bullet Camera to the left side pin of the 3 Pin Terminal Block and the brown wire to the right side pin 2 Connect the DC 12V Power Adapter to the 3 Pin Terminal Block 3 Pin Terminal Block 4 b DC 12V Power Adaptor 3 4 3 Applying Waterproof Treatment To install the Bullet Camera outdoors ensure to waterproof the cables The camera s body is waterproof but the PoE audio power and I O cables are not waterproof Use waterproof silicon rubber or the like to apply waterproof treatment to the cables The following
25. is an example of waterproofing the audio cable 0 1 7 LY ioa B 27 C GeoVision alarm shop 4 Vandal Proof IP Dome 4 1 Packing List e Vandal Proof IP Dome e Screw Adjuster x 1 e Screw Anchor x 4 e Silica Gel Bag x 2 one already placed inside the J camera e Ceiling Screw x 4 e Blue Screw x 3 e Cap Screw x 3 e Small Screw Cap x 3 e T Cap x3 e Plastic Clip x 3 TE CE se i n a e GeoUision 30 Focus Adjustment Cap 2 Pin Terminal Block GV IPCAM H 264 Quick Start Guide GV NVR Quick Start Guide DC 12V Power Adapter GV IPCam H 264 Software CD GV NVR Software DVD 4 2 verview 4 Vandal Proof IP Dome gt vas AN gt _No Name 1 Power LED 2 o Status LED 3 Default Button 4 Memory Card Slot 5 Thread Lock 6 Pan Disc 7 _ Tilt Screw 8 Rotational Screw 9 Zoom Screw 10 Focus Screw 11 Silica Gel Bag Turns on green when the power is on and turns off when there is no power supply Turns on green when the system operates normally and turns off when system error occurs Resets to factory default For details see 10 Restoring to Default Settings in the Quick Start Guide Inserts a micro SD SDHC card to store recording data Locks the housing cover to the camera body to prevent the cover from falling Loosens to pan the camera Loosen the screw to tilt the camera Loosens to adjust the camera angle Adjusts the zoom of the camera
26. isplays the camera information video settings audio data rate I O device status images captured upon alarm and GPS location of the camera Also allows you to adjust image quality and install the program from the hard drive Brings up these functions Alarm Notify Video and Audio Configuration Remote Config Show Camera Name and Image Enhance Enables the I O Control Panel and Visual Automation 9 Upgrading System Firmware GeoVision periodically releases updated firmware on the website The new firmware can be simply loaded into the GV IPCAM H 264 by using the Web interface or IP Device Utility included in the software CD IMPORTANT 1 While the firmware is being updated A the power supply must not be interrupted and B do not unplug the Ethernet cable if the cable is the source of power supply Power over Ethernet or PoE supported 2 Do not turn the power off within 10 minutes after the firmware is updated 3 f you use the IP Device Utility for firmware upgrade the computer used to upgrade firmware must be under the same network of the camera te GeoUision 1 Stop these operations monitoring of IPCam H 264 connection to GV System and remote connections to Center V2 VSM ViewLog Server and 3GPP 2 Inthe Live View window click the Show System Menu button and select Remote Config This dialog box appears Remote Config Firmware Upgrade Version v1 00 2010 10 20 Upgrade File BX1 20_ 100_101
27. on 4 Click Apply For Trigger by Input and Trigger IR by D N functions see the Video Settings section Administrator Mode chapter in the GV IPCam H 264 User s Manual in the software CD il Box Camera 1 4 Connecting the Camera The Box Camera is designed for indoor use Please make sure the installing site is shielded from rain and moisture GV BX110D 1 f youare using the varifocal lens model plug the iris control cable to the Auto Iris Connector on the camera Use a standard network cable to connect the camera to your network 3 Optionally connect a speaker and an external microphone e GeoVision 10 Optionally connect a monitor using an RCA video out wire If your signal format is PAL configure the TV Out setting on its Web interface See TV Out setting in the Video Settings section Administrator Mode chapter GV IPCam H 264 User s Manual on the software CD Connect power using one of the following methods e plugging the supplied power adapter to the DC jack e using the Power over Ethernet PoE function and the power will be provided over the network cable The status LED of the camera will be red Then you can set the IP address for the unit See 7 Accessing the Camera in the Quick Start Guide il Box Camera GV BX120D 220D 0 220D 1 220D 2 220D 3 320D 0 320D 1 Pe ae Plug the iris control cable to the Auto Iris Connector on the camera Use a standard network cable to conne
28. onent onto your computer IMPORTANT 1 Dynamic IP Address and PPPoE should only be enabled if you know which IP address the camera will get from the DHCP server or ISP Otherwise you must use the Dynamic DNS service to obtain a domain name linked to the camera s changing IP address first If Dynamic IP Address or PPPoE is enabled and you cannot access the camera you may have to reset the camera to its factory default and then perform the network settings again To restore factory settings see 10 Restoring to Default Settings in the Quick Start Guide 63 e GeoUision alarm shop 8 The Web Interface Live View In this section you can see and configure the default camera view Live View Configuration 10 56 47 Play JI lt A Information Version v1 06 2010 10 01 a Local time 2010 10 18 10 59 03 Host time 2010 10 18 10 56 47 a Online count 1 OCX Registration Path CAWINDOWS GeoO0CX WebC gt 24 i 0000000 e GeoVision No Name 1 Play 2 Stop 3 Microphone Speaker Snapshot 6 File Save T Full Screen 8 Control Panel 10 66 Show System Menu I O Control Function Plays live video Stops playing video Talks to the surveillance area from the local computer Listens to the audio around the camera Takes a snapshot of live video Records live video to the local computer Switches to full screen view Right click the image to see additional options D
29. s flexible and easy installation Pan adjustment 35 te GeoVision Rotational Adjustment 10 Hold the focus adjustment cap on top of the camera view to simulate the housing cover and adjust the focus and zoom using the focus and zoom screws Focus Screw Zoom Screw 11 Screw on the thread lock as shown in step 1 12 Secure the housing cover to the camera body as shown in step 1 Note Adjust the black mask inside the housing cover to make sure the camera view is not obscured 36 4 Vandal Proof IP Dome 4 3 2 In Ceiling Mount 1 Follow step 1 in the Hard Ceiling Mount section to remove the housing cover thread lock and back cover and take out the camera body 2 Cut outa circle with a diameter of 142 mm on the ceiling 3 Insert a blue screw to the indicated holes on the camera body 37 te GeoVision 4 5 6 38 Screw in a plastic clip to the blue screw hold it with one hand and use a screw driver to rotate the blue screw until the plastic clip moves half way down st Plastic Clip Secure a T cap on top of the blue screw with a small screw cap anda T cap screw Do not tighten the small screw cap so that the plastic clip can move down freely small screw cap Repeat steps 4 and 5 for the other two blue screws T 8 10 11 12 4 Vandal Proof IP Dome Insert the camera to the ceiling with the plastic screws moved inward Move the blue screw
30. s out and rotate the blue screw with a screw driver until the plastic clip and the bottom of the camera body clamps the ceiling tightly Connect the network and power cables to the camera See 4 4 Connecting the Camera in the Quick Start Guide Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide Follow steps 9 to 10 in the Hard Ceiling Mount section to adjust the angle focus and zoom of the camera Follow steps 11 to 12 in the Hard Ceiling Mount section to secure the thread lock and the housing cover 39 te GeoVision 4 3 3 Wall Pendent Mount For the wall pendent mount installation you need to purchase the wall mount bracket additionally 1 Take the wall mount bracket and make 2 marks on the wall for screw anchors g 2 Drill the marks and insert 2 screw anchors 3 Insert the ceiling screws and leave enough distance approximately 2 mm to hang the wall mount bracket later Long Screw Wall 40 DI Vandal Proof IP Dome 4 Hang the wall mount bracket on the ceiling screws and push the wall mount bracket downward Tighten the screws to the wall 7 5 Follow step 1 in the Hard Ceiling Mount section to remove the housing cover thread lock and back cover and take out the camera body 6 Secure the back cover to the wall mount bracket with four short screws and big screw caps both are supplied with the wall mount bracket fa gt So s 6 YA a
31. t Connects to a 10 100 Ethernet or PoE 12 13 14 15 I O Terminal Block DC 12V Port Status LED Power LED EB Fixed IP Dome Connects I O devices For details see Fixed IP Dome chapter in the GV IPCam H 264 User s Manual on the software CD Connects to power Turns on green when the system operates normally and turns off when system error occurs Turns on green when the power is on and turns off when there is no power supply 47 te GeoVision 5 3 Installation The Fixed IP Camera is designed for indoors There are two ways to install the Fixed IP Camera hard ceiling mount wall surface mount and wall pendent mount 5 3 1 Hard Ceiling Mount amaa e GeoUision 1 Paste the supplied sticker onto a desired location on the ceiling Drill the three red dots and the ellipse mark only if you wish to run the wires into the ceiling 2 Unpack the camera package and take out the camera body Use the screw adjuster to loosen the housing cover at the front and the back U0ISIN099 gt na 48 3 EB Fixed IP Dome Take out the UOISIN039 gt Secure the camera body to the mounting plate with three ceiling screws Connect the network and power cables to the camera See 5 4 Connecting the Camera in the Quick Start Guide Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide 49 te GeoVision
32. unt bracket additionally E GeoUision 1 Take the wall mount bracket and make 2 marks on the wall for screw anchors Yas 2 Drill the marks and insert 2 long screw anchors supplied with the wall mount bracket 3 Insert the wall mount screws supplied with the wall mount bracket and leave enough distance approximately 2 mm to hang the wall mount bracket later Long Screw Wall 53 e GeoVision 4 10 54 Hang the wall mount bracket on the wall mount screws and push the wall mount bracket downward Tighten the wall mount screws to the wall Follow step 2 in the Hard Ceiling Mount section to remove the housing cover and take out the camera body Secure the camera body to the wall mount bracket with three short screws supplied with the wall mount bracket Connect the network and power cables to the camera See 5 4 Connecting the Camera in the Quick Start Guide Access and check the live image from the camera See 7 Accessing the Camera in the Quick Start Guide Follow steps 6 and 7 in the Hard Ceiling Mount section to adjust the angle focus and zoom of the camera Follow step 8 in the Hard Ceiling Mount section to secure the housing cover EB Fixed IP Dome 5 4 Connecting the Camera FTR pon i Ur Use a standard network cable to connect the camera to your network Optionally connect a speaker and an external microphone 3 Optionally connect a monitor using a Video Out wire If yo
33. ur signal format is PAL configure the TV Out setting on its Web interface See TV Out setting in the Video Settings section Administrator Mode chapter GV IPCam H 264 User s Manual on the software CD 4 Connect power using one of the following methods e plugging the supplied power adapter to the power port e using the Power over Ethernet PoE function and the power will be provided over the network cable 5 The status LED of the camera will be on Then you can set the IP address for the unit See 7 Accessing the Camera in the Quick Start Guide 55 e GeoUision alarm shop 6 Cube Camera 6 1 Packing List Cube Camera e Supporting Rack Screw x 3 e Screw Anchor x 3 GV IPCAM H 264 Quick e GV NVR Software DVD Start Guide GV NVR Quick Start Guide e GeoUision 6 2 Overview 1 Microphone No Name 2 Speaker 3 LAN 4 Status LED 5 LAN LED 6 Stand screw T Default Button 8 DC 12V Port 9 Memory Card Slot 58 GS IW a Description Receives sounds Plays sounds Connects to a 10 100 Ethernet Turns red when the system powers on Turns orange when the system is ready Turns green when the camera is connected to the Internet Connects to the Supporting Rack Resets to factory default For details see 10 Restoring to Default Settings in the Quick Start Guide Connects to power Inserts a micro SD SDHC card to store recording data 6 Cube Camera 6 3 Installation
34. ut Ground Audio in Audio out TV out 43 e GeoUision 4 4 2 Connecting the Power Cable 1 Insert the black wire of the Vandal Proof IP Dome to the left side pin of the 2 Pin Terminal Block and the red wire to the right side pin 2 Connect the DC 12V Power Adapter to the 2 Pin Terminal Block 2 Pin Terminal Block 4 b DC 12V Power Adaptor 44 5 Fixed IP Dome 5 1 Packing List e Fixed IP Dome e Screw Adjuster x 1 e Mounting Plate x 1 e Short Screw Anchor x 3 4 e Ceiling Screw x 3 e Plate Screw x 3 e TV out Wire DC 12V Power Adapter e Sticker e GV IPCAM H 264 Quick Start Guide e GV IPCam H 264 Software e GV NVR Quick Start Guide CD e GV NVR Software DVD e GeoUision 5 2 Overview 10 11 46 0 R O N lt Name Focus Screw Zoom Screw Rotational Screw Tilt Screw Pan Disc Video Out Memory Card Slot Default Button Audio In Audio Out LAN PoE Description Adjusts the focus of the camera Adjusts the zoom of the camera Loosens to adjust the camera angle Loosens the screw to tilt the camera Loosens to pan the camera Connects to a portable monitor for setting the focus and angle of Fixed IP Dome during initial installation Inserts a micro SD SDHC card to store recording data Resets to factory default For details see 10 Restoring to Default Settings in the Quick Start Guide Connects a microphone for audio input Connects a speaker for audio outpu
35. ype the default IP address http 192 168 0 10 In both Login and Password fields type the default value admin Click Apply In the left menu select Network and then LAN to begin the network settings e GeoVision LAN Configuration gt Video and Motion inthis section you can configure GV IPCAM to work inside of LAN VO Control Events and Alerts LAN Configuration gt Monitoring gt Recording Schedule Dynamic IP address Select this option to obtain IP address from a DHCP server gt Remote Viewlog Static IP address Oo Selectthis option to enter a Static IP address manually 7 Network PPPoE Selectthis option to estaklish a DSL connection gt Status J Username Password gt Advanced TCPAP gt IP Filtering SNMP Setting iP Address 1921682168 Management Subnet Mask 255 255 252 0 gt Logout RauteriGateway 192 168 0 1 Configure connection parameters Primary DNS 192 168 0 1 Secondary DNS 0 0 0 0 o Optional Test DHCP Select Static IP address Type IP Address Subnet Mask Router Gateway Primary DNS and Secondary DNS in the Configure connection parameters section Click Apply The camera is now accessible by entering the assigned IP address on the web browser Accessing the Camera To enable the updating of images in Microsoft Internet Explorer you must set your browser to allow ActiveX Controls and perform a one time installation of GeoVision s ActiveX comp
Download Pdf Manuals
Related Search