User Manual
Contents
1. Digital door station in weatherproof housing Accessories Power supply components 3 Features and functions Intercom with an integrated camera and a portable 3 5 LCD color monitor thanks to its integrated battery An existing bell buzzer wire is easy to connect to the door station Encrypted signal transmission between the door station and monitor The door can be opened by pressing a button on the monitor After pressing the door bell images are recorded on an SD card in the monitor and can be watched conveniently on the PC Integrated microphone on the monitor allows speaking to the person outside Door station for a sheltered outdoor area protection class IP55 Door station with batteries for use in the event of a power failure Day night camera with integrated IR LEDs 4 Device description 4 1 Guide to the front of the monitor Red Green Off Battery status display Live cast Live cast Vol In the menu lt q gt Live cast Vol In the menu Standby Live cast In the menu Live cast OK Taste In the menu re Live cast Del In the menu Live cast In the menu ESC Device status display Blue PWR REC Off Flashes 3x per sec Flashes 1x per sec Display of the current charge level Battery low Charging Battery fully charged Switch device on Switch device off Device recording New recording in memory Click to access event list directly Navigate between menu items2. A Disclaimer This user guide has been produced with the greatest of care Should you discover any missing information or inaccuracies please contact us under the address shown on the back of the manual ABUS Security Center GmbH does not accept any liability for technical and typographical errors and reserves the right to make changes to the product and user guide at any time and without prior warning ABUS Security Center GmbH is not liable or responsible for direct or indirect damage resulting from the equipment performance and use of this product No forms of guarantee are accepted for the contents of this document Explanation of symbols The triangular high voltage symbol is used to warn of the risk of injury or health hazards e g caused by electric shock The triangular warning symbol indicates important notes in these operating instructions which must be observed This symbol indicates special tips and notes on the operation of the unit Important safety information All guarantee claims are invalid in the event of damage caused by non compliance with this user guide We cannot be held liable for resulting damages In the event of material or personal damage caused by improper operation or non compliance with the safety information we cannot be held liable All guarantee claims are voided in such cases This device has been manufactured in accordance with international safety standards Please read the fol
3. c ccc ccccecc cece eeeeeee eee eeeeeeeeeseeseeseeeseeseeeeeeseeseeeseeseeseeeeeseeseees 16 6 5 Event SE praia rasienneinaaresoaseipemncadntasonastiameniaiamntaas saihienetitenaeimedetaatnnesnianneah nadreniainapaatsnninemneeens 17 6 6 System settings iiseiisiccisceccetecinscinnccionapadeeierixne ce cearetutssateamnestassiedlwecseaeistacadeddnsccensesnsiadadevense 18 7 Maintenance and Cleaning ccccccccsscceecescceeeeeeceeeeeeeneoneeensonesenseeseeseneseeseneoessensones 19 Ar MamnenaneE seese a ge ee mete gr ce EEE 19 TZ CONS RMN gas ocr se gn ee don A A E A T T 19 o BC oe ean ese ne ce eee E Se ee eee ee ee ee ee eee eee 19 9 Technical data sssrinin ea aE E E Eaa 20 1 Intended use Digital wireless video intercom system comprised of a weatherproof housing and a 3 5 LCD monitor each with a hands free speaker and power supply unit You can install the system next to your door bell and connect it to your door opener The compact 3 5 LCD color monitor is portable meaning you do not have to walk to the intercom The integrated microphone makes speaking to the visitor outside more convenient and the door opener can be operated from the monitor The digital transmission technology ensures interference free reception After the door bell has been pressed images are recorded on an SD card not included For a detailed description of functions refer to Section 3 Features and functions 2 Scope of delivery
4. Press to delete your selection To cancel the deletion process press amp Your recordings are always made with sound and it is therefore important to observe the stipulation on page 2 in order to avoid putting yourself or other persons in an unlawful situation To change the volume during playback please use the Vol to turn the volume down or Vol to increase the volume 17 6 6 System settings Time setting settings for date and time Time setting CF OE Oe ae Us Or Year Month Day Hours Minutes Software Version RX Ver TX1 Ver TV Format Set to factory default Restore default parameters Factory Default Press the button to toggle between year month day hour minute Use the A Y buttons to adjust the values Confirm your input by pressing the OK button This indicates the version of the software being used by the door station and the monitor Use the lt gt buttons to select the preferred TV format You can choose between NTSC and PAL Confirm your selection by pressing the OK button Please note that the format selected can affect the resolution Press the OK button to launch the factory settings Confirm your selection by pressing and cancel the process by pressing Important Please note that this procedure does not change the formatting of the SD card 7 Maintenance and cleaning 7 1 Maintenance Examine the technical safety of the product regu
5. choose between the following Camera Setup Camera settings Camera brightness Pairing add door stations Recorder Setup Recording settings Visiting record visitor is being recorded SD Card format memory capacity on SD card SD Card overwrite SD card circular buffer Event List Event list The recordings are saved to sub folders which are named with the date on which the recording was made The recordings are saved as individual files with the duration of the recording being used as the file name System Setup System settings Time setting settings for date and time Software version TV format TV output resolution Factory default restore factory settings 15 6 3 Camera settings Camera brightness Camera Brightness Pairing Visiting Record SD Card Format To change the camera brightness level press the OK button which appears under the menu item Camera brightness A selection bar with settings from 0 to 9 appears Settings can be changed using the lt P gt buttons and be confirmed by pressing the OK button The connection between the door station and the monitor is set up under the menu item Pairing To do so press the OK button The system will now search for the connection to the door station with a round arrow appearing for 60 seconds Press the PAIRING button on the door station for these 60 seconds When a connection is established the monitor will switch to a
6. inform the delivery service Contents l UAE USE eci EEA aa a ni 6 2 OCOD OP CONN cee a EEEE E EE 6 De Featuresand TUNCUOINS sinccvie teens sananieddewmnmesnnaceivan dulce dcsecinussdeuuentccmacubanneesandsedmeuseaamuineebe 6 A Device COS CRO ONO IW aoa risers eet geet tee cee eens E EEEn T 4 1 Guide to the front of the MONItOM ccc cc ee eee eeee sees eeseeeesa esse eeseeeeseeeseeeeaeeess T 4 2 Guide to the rear of the monitor cece cceeceeeeeeeeeeeeeeaeeeseeeeseeeseeesaeeeseeeseeeeaeeess 8 4 3 Guide to the connections on the monitor cccccccccceeeeeeeeeeeeeeeeeseeesaeeeaeeeseeeeneeens 8 4 4 Guide to the door station cc cccccccceeceeeeeceeeeeeeeeeeeseeeeeeeeseeeseeeeseeesseeeseeeseeeeseeesenees 9 4 5 Guide to the cable CONNECTIONS cc ccccecccseeeceeeeeeeeseeeeaeeeaeeeseeeeeueeseeesneeaneenaees 10 5 INS RUN ascii a a eee snes erase oles Eaa aoai a aa aiaia 11 5 1 Installation the door Station ccc ccccccc cece eee eeee esse eeseeeseeeeeeseeesseeeeeeseesaaeeeesenenass 11 5 2 Assembling the door Station c cc cccccccccc cece cece eeeeeceeeeeeseeseeeseeseeseeeeeseeeaeeaeenenegees 12 95 9 Installing th CMO coos ence eee si ise a eects eee 13 6 OPETI ON er E E O S 14 ol CVE CIST o A A E E E E A EA E E EEN A ER 14 o2 Namn Meni se N E E E E a a a 15 6 3 Gamera SSS io cco gee pcre ew ess see se cei eee ee 16 6 4 Recording settings
7. live cast Press the OK button to switch between ON and OFF If you switch it to OFF the visitor will not be recorded on the SD card when the bell is pressed This indicates the memory capacity which is available and the free memory capacity on the SD card SD Card Overwrite SD card circular buffer SD Card Overwrite 6 5 Event list Event List Delete Important Use the lt P buttons to activate the SD card circular buffer ON or to deactivate it OFF Confirm your selection by pressing the OK button The circular buffer is activated by default Important When the memory capacity is reached the monitor will continue to record and will delete the oldest recordings on the SD card The SD card capacity display flashes 0 0 in red Use the arrow buttons to navigate between folders Press the OK button to select the required folder Select the file with the required recording from the sub folder and play it by pressing the OK button Press the A or Y buttons to fast forward or reverse at 2x 4x 8x 16x normal speed Please note that when a manual recording is made the maximum duration of recording is 10 minutes If this time is exceeded a new file will be created Press the DEL button to enter delete mode The current file or the current folder will flash on the display Use the lt b buttons to choose between all files or an individual file Press the OK button to confirm your selection
8. Reduce volume Navigate between menu items Increase volume Navigate between menu items Switch on monitor Switch off monitor Navigate between menu items Speech function Confirm the settings and changes Start stop the recording Delete the recording Only possible with an SD card Door opener Quit the sub menu The system will quit the menu automatically after one minute of inactivity 4 2 Guide to the rear of the monitor mm ZZN Antenna MUU uu K Way Stand len 7 SE i f a F if 4 g F A i ji f A 4 3 Guide to the connections on the monitor Power supply 5 VDC 1 A DC 14 5 x 4 8 mm Output for displaying the screen image on a different device PA Op using an RCA cable not included SD card slot Slot for using an SD card with a max capacity of 32 GB O Power button and Switch monitor on or off menu button Live cast Open exit the menu 4 4 Guide to the door station Tle I dl Infrared LED Loudspeaker Lens Housing for attachment Bell button When the bell button is pressed the monitor is activated To connect the door station to the monitor the pairing Pairing button button must be pressed More information can be found under point 5 3 Reset button Reset button to restart the door station O Connection for bell O DC O Power supply Term
9. Security Tech Germany TVAC80020B User guide Version 08 2012 Original user guide in English Retain for future reference Introduction Dear customer Thank you for purchasing this product This product complies with current domestic and European regulations Conformity has been verified and all related certifications and documents are available from the manufacturer on request www abus sc com To ensure this condition is maintained and that safe operation is guaranteed it is your obligation to observe these operating instructions Read the entire user guide carefully before starting operation of the product and pay attention to all operating instructions and safety information All company names and product descriptions are trademarks of the corresponding owner All rights reserved In the event of questions please contact your local maintenance specialist or dealer A Warning as required by 201 StGB German Criminal Code Whosoever unlawfully makes an audio recording of the privately spoken words of another or uses or makes a recording thus produced accessible to a third party shall be liable to imprisonment or a fine Whosoever unlawfully overhears with an eavesdropping device the privately spoken words of another not intended for his attention or publicly communicates verbatim or the essential content of the privately spoken words of another recorded or overheard shall incur the same penalty
10. ding To display the monitor images on another display unit please proceed as follows 1 Connect the jack plug to the AV OUT connector on the monitor 2 Then connect the RCA cable as shown in the drawing TV AV Mode US ol Ge a eS a ay Video _ audio 13 6 Operation To switch the monitor ON OFF press and hold the power button for at least 2 seconds After each start the monitor will switch to the live cast selecting the last viewing settings If the 0 symbol is displayed then the SD card was identified correctly by the monitor and is functioning properly 6 1 Live cast Tail 1 8 erEc Obol osc NO SIGNAL 2011 05 01 01 12 45 14 30 11 Display Visitor is being recorded Battery status display for door station AN Yellow Battery charged Red Battery low Recording display Flashes during recording D No SD card inserted Ti Full SD SD card full Err SD SD card is not detected z SD card blocked SD card will be overwritten when memory is full SD card memory capacity ss s Ssr card memory SD card memory capacity ss s Ssr NO SIGNAL No connection between the door station and monitor 2011 05 01 6 2 Main menu Press the MENU button to enter the main menu You can navigate between the individual menu items using the arrow buttons Important Please note The symbols will be hidden automatically after being displayed for 10 seconds You can
11. e the drill holes to mark the surface and drill the holes Insert the wall plugs provided before attaching the bracket using the screws Important Before starting the installation make sure than the wireless transmission range at the site of the required installation is sufficient Important Before replacing the cover of the device connect the door station to the monitor 2 Close the housing for the door station using the four screws provided 3 Place the door station into its housing and attach it using the anti theft screws provided The matching screwdriver has been enclosed with the package 12 5 3 Installing the monitor 1 Connect the power supply unit to the monitor 2 Switch the device on To do so press the power button 3 You can now connect the monitor to the door station To do so please proceed as follows When the menu item Camera set up appears on the monitor select the sub item Pairing and press the pairing button on the door station Important Please note that if the monitor does NOT have an external power supply it must be charged for at least 8 hours prior to being used for the first time The batteries will provide power for approx 3 5 hours Important The integrated battery allows you to use the LCD monitor flexibly If the battery LED lights up in red then the batteries must be charged Please note that the battery is always charged to a level which guarantees loss free recor
12. ice 3 Use overvoltage protection to prevent damage caused by overvoltage e g electrical storms 3 Disconnect defective devices from the power immediately and contact your specialist dealer When installing the device in an existing video surveillance system ensure that all devices have been disconnected from the power supply and low voltage circuit If in doubt have a specialist technician carry out assembly installation and connection of the device Improper or unprofessional work on the power supply or domestic installation puts both you and other persons at risk Connect the installations so that the power supply circuit and low voltage circuit always run separately from each other They should not be connected at any point or be able to become connected as a result of a malfunction Avoid the following adverse conditions during operation Moisture or excess humidity Extreme heat or cold Direct sunlight Dust or flammable gases vapors or solvents Strong vibrations Strong magnetic fields e g next to machines or loudspeakers The camera for the door station must not be directed toward the sun as otherwise the sensor may be destroyed e The door station must not be installed on unstable surfaces Unpacking the device Handle the device with extreme care when unpacking it If the original packaging has been damaged inspect the device If the device shows signs of damage return it in the original packaging and
13. inal block O UNLOCK O Connection for door opener UNLOCK O f e fe 4 5 Guide to the cable connections Cable lug with connecting cable for the door opener Cable lug contacts For connection to a door opener already installed Stripped cable ends For connection to the terminal block in the door station Round socket with connecting cable for power supply unit Pond socket a ee to the connecting cable for the power supply Stripped cable ends For connection to the terminal block in the door station Red DC For connection to the terminal block in the door station Q Stripped cable end black DC Power supply unit for the monitor i Wall adapter Connection for power supply 2 Round plug For connection to the monitor Power supply unit for the door station Wall adapter Connection for power supply 2 Round plug For connection to round sockets 10 5 Installation 5 1 Installation the door station To install the door station please proceed as described in the following Preparation MEIN Hi N TW Tt ool it 1 Please remove the rear cover of the door station and insert 6 AA batteries Make sure the polarity is correct 2 The LEDs will then light up in green for 5 seconds 3 The door station is now functional Important Weak batteries can cause the device to function incorrectly please replace a
14. larly e g check the housing for damage If it seems that it may no longer be possible to operate the device safety stop using the product and protect it from unintentional use It is likely that safe operation is no longer possible in the event that e The device shows signs of visible damage e The device no longer works correctly Please note You do not need to perform any maintenance on this product There are no components to service or anything inside the product to check Never open it 7 2 Cleaning Clean the device with a clean dry cloth The cloth can be dampened with lukewarm water if the dirt on the monitor is hard to remove Do not allow any liquids to enter the device Do not use any chemical cleaning agent as they could damage the surface of the housing discoloration 8 Disposal Devices displaying this symbol may not be disposed of with domestic waste At the end of its service life dispose of the product according to the applicable legal requirements Please contact your dealer or dispose of the products at the local collection point for electronic waste 19 9 Technical data Model number Frequency Modulation Transmission power Sensitivity Wireless range DC voltage supply Power consumption Battery type Transmission channels Viewing angle Lens Resolution Number of IR LEDs Image sensor Range of night vision function Video signal Audio signal Outputs Storage mediu
15. lowing safety instructions carefully Safety information 1 Power supply 100 240 V AC voltage 50 60 Hz using a power supply unit for 5 V DC Only operate this device using a power source which supplies the grid voltage specified on the type plate If you are unsure which voltage is supplied at the installation location contact your power supply company Disconnect the device from the power supply before carrying out maintenance or installation work Overloading Avoid overloading electrical sockets extension cables and adapters as this can result in fires or electric shocks Liquids Make sure that no liquids of any type are able to enter the device Cleaning Only use a damp cloth to clean the device Do not use corrosive cleaning materials Disconnect the device from the power supply while doing so Accessories Only connect devices that are suitable for the intended purpose Otherwise hazardous situations or damage to the device can occur Installation position This device is suitable both for operation in protected outdoor areas as well as indoors The product may be damaged if it is dropped even from a low height Install the device so that no direct sunlight can shine on the image sensor Pay attention to the installation instructions in the corresponding section of this user guide Never place the device close to heaters stoves other sources of heat or in direct sunlight Only operate the device at locations whe
16. m IP protection class Rechargeable battery running time Dimensions Net weight Max operating temperature 15V DC 1 5A oVDC 1A Max 180mA Max 650mA TP l Li lon polymer battery 3 7 V 6 x AA 1 5 V lithium batteries 1 800 mA 85 H 65 V D 1 8 mm ee 640 x 480 pixels VGA O ORRE fF y l CMOS e Bm S OV pp 75 OHM oO pp 600 OHM oo SD card max 32GB IPS WxHxD 85 x 169 x 36 mm WxHxD 133 x 87 x 27 mm 0 205 kg 0 2 kg 10 C 40 C 10 C 40 C The wireless transmission range depends on the environmental factors e g mobile communication masts high tension pylons electrical wires ceilings and walls etc If conditions are not favorable the range will be limited 20
17. ny depleted batteries Important If you are in battery mode please press the call button first to start operation of the door station Il Connecting the door station Le L h 11 Remove the rear cover of the door station Attach the red cable for the round socket next to DC in the terminal block The black connecting cable for the round socket must be attached to the terminal point DC The two connecting cables for the cable lug must be inserted next to UNLOCK with the terminals being provided for an existing 2 cable door opener connection A round plug with a power supply unit can now be connected to the round socket Turn on the power to the power supply unit A door bell can be connected to the two uppermost connector points a oO Important Please note that this contact is a potential free relay contact and a bell which lacks a power supply of its own can therefore not be connected Important You also have the option of connecting your door opener directly to the door station or to connect an existing door opening transformer using a relay Important Please note that only DC door openers can be actuated with AC door openers not being able to be actuated More Information www abus com gt TVAC80020 5 2 Assembling the door station MELIN i TA Tal b ies a ee S 1 Use the door bracket to help you find a suitable place for installation Us
18. re temperatures within the permitted ambient temperature range of 10 C to 50 C prevail 7 Wireless transmission The wireless range depends on a variety of environmental factors The local conditions at the installation site may have a negative impact on the range When there are no obstructions between the receiver and transmitter a range of up to 150m is possible but this range will be considerably less within buildings The following environmental conditions compromise both the range as well as the frame rate Mobile communication masts high tension pylons electrical wires ceilings and walls devices with the same or an adjacent wireless frequency Warnings Observe all safety and operating instructions before putting the device into operation for the first time 1 Observe the following information to avoid damage to the mains cable and plug e Do not modify or manipulate the power cable or plug e Do not pull the cable when disconnecting the device from the mains power always hold of the plug e Ensure that the mains cable is positioned as far away as possible from any heating equipment as this could otherwise melt the plastic coating e The power supply unit for the door station must be protected from damp and moisture 2 Follow these instructions Non compliance with these instructions could lead to an electric shock 1 Never open the housing or power supply unit 2 Do not insert any metallic or flammable objects into the dev
Download Pdf Manuals
Related Search