DIPCHECK®
Contents
1. is calculated by the TTM Using the key fl it is also possible to display the actual quantity still within the compartment Picture 12 Residual Quantity within the Compartment On this screen the value after Vt is the quantity uncompensated still loaded H shows the level of product and Ta is the actual temperature measured in the pipework below the compartment Using the key J the first detail may be recalled Pressing the key 0 the delivery overview is again displayed When the deliveries from all desired compartments have been completed press the key END Should the bottom valves still be open they are now closed before the system repeats the averag ing process as described before Since waves are usually not produced during delivery the final gauging is usually performed considerably faster The same screens as shown under Picture 7 and Picture 8 appear in sequence before the measurement is completed From the volumes at the initial and final gauging the system now computes for each compartment the quantities by which the contents has changed and displays them starting with compartment 1 COME s PPOOGUWCLa D o volume chanase Picture 13 Display for compartment without change In the example no significant change of the product level has been observed for compartment 1 To display the delivered volumes of other compartments simply press the corresponding number key Picture 14 Display of Quan2. Keyboard Picture 1 shows the keyboard and the display of the Tank Truck Manager TTM which is used as the command center of DipCheck The keyboard consists of a numeric block to the right and spe cial symbol keys to the left which have the following meaning DELIVERY 77 Key 1 Initiates a delivery transaction During setup also used to switch J products LOADING CD Key 2 Initiates a loading transaction During setup also used to switch prod 2 ucts END Key 3 Terminates delivery and loading transaction as well as many other data entry HELP MODE e Calls a brief help screen to show what can be done in the actual situation PRE SET Activates a quantity pre set for delivery or loading from to a compartment ri PRINT Request of printout of several documents if a printer is installed MEMO AS Recall one of the previous 450 delivery loading transactions PANIC E Close all bottom valves if they are controlled by DipCheck SET UP JV Call the setup menu AUTO m Display various status screens U Next screen SZ ff lt Previous screen Numeric block CE Erase last numeric entry B Acknowledge the number just entered 1 2 9 0 Numeric input keys while the cursor is positioned on a numeric data field Otherwise the keys 1 7 reduced range for vehicles with less than 7 compartments can be used to select the compartment for detailed view The key 0 is used to
3. are internally treated as the same product e g for tem perature compensation On the delivery note these products are dis tinguished 3 15 Digital Input Status Meu atiis urn 1 1 WE Gaeeioea GGG hu Pt s H ML Picture 45 Status of digital Inputs of PLC This screen shows the status of the up to 24 digital inputs of the PLC if a PLC is connected to the system and if the hardware option PLC is enabled The cursor is merely used to obtain the meaning of the digital signal that has been selected by placing the cursor over the corresponding digit 3 16 Digital Output Status and Manipulation Picture 46 Status of digital outputs This screen is used to indicate and to modify the state of the digital outputs of the PLC if one is connected to the system The cursor may be placed over any of the digits in the second row In the third line the meaning of the digital output is indicated as well as the current status YES if it active and NO if it is not Typing a 1 causes the selected output to become active and typing 0 will turn it off again 22 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 23 of 24 4 Table of Contents 1 I trc cc crc cn 2 2 Operation by INE Driver TT RT 2 2 1 Keyboard coe e E E EE c E A E D ort 2 2 2 Power Up the System sssesssssesesesssises eee neater eee nn neca s E 3 2 3 Display of Loading Status siessssissesseseseeee enn
4. end of the transaction followed by driver and vehicle number if not both are zero not printed here 4 5 Header line for the subsequent quantity list 6 Home Heating Oil has been delivered from Compartment 1 starting at a volume of 9240 li tres down to a volume of 5806 litres The sign right after the quantity show that the prod uct detector mounted in the pipework below the bottom valve was dry before and after the delivery In the column Dif Vt the difference of the initial and the final quantity is calculated 3434 I When temperature compensation for the product is activated as this is the case for home heating oil an additional quantity appears on that line which is Vo or the delivered volume at 15 C The entire line is enclosed in asterisks to indicate that the values are measured and or calculated by an approved system 7 Similar to line 6 but please note the missing asterisks which is in this case due to the fact that the delivered quantity of 939 litres is smaller than the minimum deliverable quantity for this compartment 8 Explanation as for line 6 9 10 If the same product is delivered from more than one compartment the sum of the quantities is calculated and printed out at the bottom of the document 2 8 Status Report At any time during the display of the loading status using the key PRINT a status sheet may be printed onto a blank form to be inserted into the printer beforehand which shows t
5. is the password at the time of delivery oo ee Help persistence is the number of seconds that short hints ap p aen Lines pearing after a change of state of the system will be displayed DeStuttoart BAVOS Vehicle number is an arbitrary ID number for the vehicle which will be printed on the delivery tickets when it is different from Picture 18 User Parameter List zero Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 9 of 24 Driver number and Trip number will be printed on the delivery ticket when they are different from zero These values are unprotected i e they may be entered by the driver at any time during the trip They have no influence on the software and only serve for information Lanquage is the communication language of the system used on the screen as well as on print outs Product assignment shows the products currently loaded or most recently being loaded in the compartments The product number given refers to the subsequent list of Product names In the ex ample document home heating oil is loaded in all four compartment Product name shows the abbreviations and names assigned to the products The names shown correspond to the standard assignment according to DIN 26051 1 Up to 20 user defined products may be configured HW and SW Options show which drivers and special functions of the system are enabled Each digit in the string is either 0 meaning that the appropriate option is disabled or
6. return to overview Enter a negative sign for numeric values decimal separator for entering decimal fractions Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 3 of 24 gt Cursor control keys These are not only used to shift the cursor left and right but also between the max three data lines by rolling over the line ends 2 2 Power Up the System Before any measurement can be performed with DipCheck the system has to be powered up using the central power switch usually located in the driver s cabin NOTE Leave the system switched off while on the road Switch it off for 5 seconds before any transaction if it was inadvertently left on After a few seconds the program starts up with a logo screen which is displayed while the system is performing an extensive self check see Picture 2 Picture 2 Logo Display after Power Up When the self tests have been terminated after approx 10 s the version of the software is dis played lectronic dirFztic Ul1 1zF 0213939 DEZIDHTH GmbH Picture 3 Version Display afteer Power Up After about 3 5 seconds a short help text is shown Start delivery 5 key 1 Start loadirns gt key 2 Picture 4 Short From Help Text By pressing the END key or automatically after approx 3 5 seconds the actual loading status of the compartments of the tank truck is displayed see Picture 5 2 3 Display of Loading Status In the basic stat
7. screen previously displayed 2 10 3 Recall Memory Data The system contains a memory for the results of the most recent 300 transactions Each transaction loading or delivery may consist of up to seven separate quantities depending on the number of compartments of the system The transaction memory my be recalled by simply pressing MEMO which lets the following screen with the header data of the most recent transaction appear Picture 24 Memory Recall Last Transaction The header data of a transaction consists of The number of the transaction identical with delivery note number The customer number if not input 00000000 appears as shown Date and time of the start of the transaction initial gauging terminated The duration of the transaction time between initial and final transaction in minutes And if applicable as shown in the picture above a global error mark if one or more of the measurements are disturbed the word Error is displayed in the lower right corner Using the keys ft and the transaction memory may be browsed and any earlier transactions be selected While the header data are displayed hitting one of the numeric keys 1 7 selects the details data of this transaction for the desired compartment If for the selected compartment a significant change has been observed during the selected transaction a screen similar to the following one will appear Picture 25 Memory Re
8. therefore be inaccurate 2 9 Parameter Printouts 2 9 1 User Parameters USER DATA j j j Date t 19 12 2005 14 37 At any given time a list of user parameters may be output A de Vehicle Havas tailed explanation of how to modify these parameters can be Neas Container 11751004 found in the chapter Set Up We recommend to print such a list Electronic dipstick Ur 2 514 ifi i i Sa Creation Date oi2ivi4i00 after every modification in order to document the new status and Compilers VAR DOSO U2 LLR DOSODI DDES 10b to re check the modifications done Z BAYS Level Court Last zage Current Pud To print a user parameter list first insert an empty form into the D printer From the status overview press the key SETUP then END a password is optional but not required Then press T cons wat a a ae Mi i persistence lt au twice until the screen shown in x Min Vol Change appears Ve i 11751006 Then press PRINT gp c7 j healt o P NET Address 0M 8 6 A document similar to the one shown to the right is output atar Tee E Lm Prtr haht width z iof 5 line i pos del M i Password is a key number which may be modified by any user odiis Tick E who knows the actual password that is needed to modify user a ill parameters It is only printed if it was entered during the proce cre E Odgy T8 49 dure above otherwise the line will not appear The number indi LAB ar cated 16794325
9. 1 if the option is enabled The purpose of the digits may be interrogated within the set up menu see The exam ple shows that no software options are activated and that Printer and Service station polling are enabled 2 9 2 Parameters under weights and measures control While the user parameter may be modified by any person knowing the password the weights and measures pa rameters may only be modified during the initial verification of the TTM A master reset is needed if one of these pa rameters must be modified which is done by separating the power supply unit at the rear of the TTM from the dis play part for a few seconds All parameters will be lost af ter that procedure and will have to be re entered manu ally In addition the electronic seal counter in the dip con troller will be incremented after a master reset It is possible however to inspect and or print the pa rameters at any time even without knowing the password The calibration data consist of a general set of values and one diptable per compartment which also contains any compartment specific data as e g the smallest deliverable quantity To print the weights and measures controlled parameters press SETUP then END password does not need to be entered Then repeatedly press U until the screen with the TTM software version appears see Now insert paper into the printer and press PRINT A list as shown in picture 20 is now generat
10. 1 of the controller for com 2c ste partment 1 and so on 10 5 93 93 5 96 The diptable which follows consists of the following columns e 3 Nr is a sequence number with no specific significance just to T a E make sure that all points are printed s A Levl mm is the level at which the volume has been measured i pm during the calibration 1 hi ed 7986 8 4 08 Volume L is the volume being in the compartment at that level has been entered during calibration L mm is a calculated column containing the gradient litres per millimetre of the dip curve at this point and which only serves as a Picture 20 Dip Table Printout means to verify the data of the diptable Since a part of the values is entered manually errors may occur which if they are significant can safely be detected by in specting the L mm column Independent of the shape of the tank cylinder box shaped or other the gradient of the curve varies only very very slowly and smoothly It never jumps i e goes up and down within a few points If such a variation is detected an error has been introduced that should be eliminated in order to avoid measuring errors during operation The value must steadily and monotonously increase from small values at the bottom of the compartment reach a maximum at the middle of the compartment and then again decrease steadily until the top of the table 11 Operation Manual DIPCHECK dated08 03 06 file xq302bedienengl4
11. Operation Manual DIPCHECK Electronic Gauging System for Road Tankers by Dr R Decker version 2 51 dated 02 03 2006 This document and all ideas described therein are the entire property of DEZIDATA GmbH and must not be forwarded to third parties without our express written consent Failing to observe this restriction may lead to a request for compensation of the resulting losses Picture 1 Kevboard and disolav of the TANK TRUCK MANAGER IndustriestraBe 10 D 94469 Deggendorf Tel 49 991 29090 0 Fax 49 991 29090 29 eMail info dezidata de WWW hittp dezidata de Gesch ftsf hrer Siegfried Zisler Dr rer nat Rainer Decker Registergericht Deggendorf HRB 2040 Ust ID DE 812 607 748 Postbank N rnberg BLZ 760 100 85 Kto Nr 49 52 858 Sparkasse Deggendorf BLZ 741 500 00 Kto Nr 380 007 187 Operation Manual DIPCHECK dated 08 03 06 file q302bedienengl4 page 2 of 24 1 General DipCheck is an electronic system to precisely determine the liquid volume loaded in the compart ments of tank trucks Any loading or delivery is registered by controlling or monitoring the bottom valves and other de vices on board of the truck DipCheck is pattern approved by the German PTB Physikalisch Technische Bundesanstalt under the approval sign 4 412 99 05 In combination with a suitable measuring container compartments of a tank truck DIPCHECK may be used for legal trade 2 Operation by the Driver 2 1
12. al DIPCHECK dated08 03 06 file q302bedieneng 4 page 16 of 24 3 Configuration This chapter describes all operations that may be necessary during the installation of the system The parameters which may be changed belong to either of the following two groups 1 weights and measures parameters may only be modified while in calibration mode 2 User parameters may be changed by any person who knows the password 3 1 Entering Setup Simply press the key SETUP to get into setup First a password will have to be entered if any of the user parameters are to be changed Note While in calibration mode it is not necessary to enter a password the system is unprotected It is also not necessary to enter a password if parameters are only to be inspected but not modified 3 2 Password page Picture 30 Password Entry Screen Password After positioning of the cursor the password a string of up to eight digits may be entered here and terminated with Seal Value of the electronic seal counter of the dip controller Sealed The value indicated here is zero while the system is in calibration mode If any value different from zero is entered in this field the calibration mode is irrevocably terminated that is all parameters under weights and measures control can not be modified The only way to break this sealing is a master reset unscrew and remove the power supply box at the rear of the TTM which will
13. bring the unit back to calibration mode But after a master reset all parameter modifications including the dip tables Will be lost The password screen must be acknowledged with the key END if parameters are to be modified the password has to be entered first 3 3 Time and Date After the password screen the time and date of the real time clock built into the TTM are displayed Picture 31 Entry of Time and Date If necessary any of the numbers may be changed by positioning the cursor over the appropriate number enter the new value and terminate with From this screen all other setup screens may be reached using the keys U and fl 16 Operation Manual DIPCHECK dated08 03 06 file q302bedienengl4 page 17 of 24 3 4 Diptables DirFtable for Comf 1 Picture 32 Diptable Display of Compartment no This screen is displayed only for a few seconds to indicate the compartment number of which the diptable is displayed It may be recalled at any time by pressing the key 3 5 Display of Diptable When a diptable is already stored it will be displayed after the compartment number screen Switching between the compartments is done by pressing the appropriate numeric key 1 7 up to the hightest compartment number only Printing of the dip table may be initiated by pressing PRINT SUMP 4 m oO umm 6011 9L 7 5 Djulu o Er o Picture 33 Diptable Display Using the keys and gt a
14. call Single Compartment Using key 0 the header data will be displayed again If the key PRINT is pressed while the header or the compartment data of a transaction are dis played a copy of the appropriate ticket will be printed best to insert paper into the printer before doing so The memory inspection is finished by hitting hte key MEMO again s 3 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 14 of 24 2 11 Diagnostic Features At any time from the basic state compartment overview of the TTM one of the following diagnos tic screens may be called Though harmless the functions are not needed during normal operation and should thus only be activated on request of a technician All of the diagnostic screens described below are called from the trip data input screen see Picture 16 para 2 6 by a single keystroke The trip data screen is called by use of the AUTO key 2 11 1 Temperature Compensation Calculator While the trip data screen is displayed press DELIVERY and the following screen appears which may also be used during metrological tests Picture 26 Temperature Compensation Calculator By entering one of the values described below any volume of any temperature and of any type of liquid can be compensated for the influence of the temperature expansion or contraction The vol ume of the liquid as if it had the so called base temperature will be computed The base tem
15. dnlc cA 19 Picture 40 TTM SW Version Comp amp Product Count nennen enne enne ener rennen nennen enne 19 Picture 41 Inclination Sensor Parameters 5 2 eren ret rt tnter aene en Ente Pe pe nob eaa Re ekle RE Deere ena cepe kso pepe hu 20 Picture 43 Averaging Count Wave Height Max duration of Power Filures ssesseeeeneeneen 20 Picture 44 Status Display of Dip Controller 22 inttr nin cnin entere Li ere nena R Lua de E da ond aaa eaa naana aia 20 Picture 45 Hardware Configuration Option 2 2 ecce eoru cen ette ai dence de Read sonia D a Exe e a anae a neatinse 21 Picture 46 Software Configuration Options ssesssesssesseseseeene eene nnne nennt nennt nennt reset rre tren eterne nnne nnne 21 Picture 47 Status of digital Inputs of PIG ise con euro eta tre ree here ras epe ie Enn tube Ex uera iet pea geni eire cede ERR 22 Picture 48 Status Of digital OUTPUTS sss inrita tere dis eir ine Pda rade ra iei latere rp De ide Db 22 24
16. e the system always displays the loading status of all compartments of the vehicle The following picture shows an examples for a four compartment vehicle Picture 5 Loading Status Display The liquid volume contained in each compartment is displayed as a black column the height of which corresponds to the percentage of the total volume for this compartment In the upper text line the product loaded or previously loaded if the compartment is empty is displayd The numeric val ues in the second row are the volume in cubic metres or thousands of litres Finally a small rectangle symbol at the bottom of each compartment area shows the filling status of the pipework below the bottom valve if the sensors are installed If the rectangle is hollow as shown in the picture for compartments 2 3 and 4 the pipework is empty whereas in case of a full rectangle which disappears in case of the partially filled compartment 1 of the example the pipe work is at least partially filled ET Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 4 of 24 By pressing the numeric key that corresponds to the compartment number 1 4 in the example up to 4 a detail screen may be called which shows the precise measuring results of any desired compartment see Picture 6 Detail Screen in Idle State The detail screen shows the tank number the product loaded the precise level in millimetres the volume
17. e estne nitrate nenne sintesi nennen ceca oa ARR 3 p Mu ec EE 4 25 OUI NG MR EHE re 6 PA META IC MOI 6 2 7 Printing a Delivery or Loading Ticket nennen enne nnns 6 QO SLAMS IS NC E EE pP E E 2 9 Parameter Printouts cerne reser coetu Ert E crea be etate dane de sedan usan d dee Runs estes lense ER TuS 8 User Parameters ueri eer ote nee eee ney ee reer ee EI MEL ILLI up lm 8 2 9 2 Parameters under weights and measures control eeeeeeesseeeeeeeeeneene nennen RR 9 iOS MEDIO E cR 11 2 10 Optional Functions and Data Input oti oett eet E gura n t AENEA EES 12 2 10 1 Quantity Predetermination cioe tre eerte eere tr eek eh ae ae a i ee Ae aed e ENS 12 2 10 2 Entering a Customer or Depot Number esssssssssssseeseeneenee nennen nennen nennen nennen tnn entere nnne en renes 12 2 1023 Recall Memory Data oree ae ea tes esc bus bay on ases eee taste fus credendi ue TO 13 2 11 Diagnostic Features creto rei tec D sad x e nna aper deca n raga OE OsR a PUER URS ERENS 14 2 11 1 Temperature Compensation Calculator esses iaie nnne nnn nennen nnne nere nnne 14 2 11 2 Inclination GOfTeclOl osi cedere rne eer E Fon Ge ehe Dee aerae Pea aspe sa Feet inea Dre en aAA Deus etes dio Ein AEri Rai EE 14 Z2 Esse fep ciaBIlori e EE 15 2 11 4 Display of Approval Signs Digital Type Label sssssssseeeeeeeeeeneenenneee nennen nennen nnn 15 S esegue TETUER 16 9 1 Enteritig Setup s
18. e proper place and is now stored 6 Any errors may be corrected by repeating the above procedure The value for the vehicle number cannot be modified on this screen Use the password protected Setup for this purpose To return to the basic state loading status overview press either END or AUTO 2 7 Printing a Delivery or Loading Ticket Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 7 of 24 Provided that the system is equipped with a printer and if at least in one compartment a significant change has been detected during a transaction a ticket may be printed Insert a blank document into the printer and press the button PRINT during the display of the quantity delivered from or loaded into one of the compartments e g as shown in Picture 14 Below an example is shown 1 DELIVERY NOTE 2 DELIVERY 2 1 copy of document 3 pate 16 09 1999 15 16 15 21 K Prd bef after Dif Vt V 15aC 6 1 HEL 9240 5806 3434 3409 L 7 2 DI 5907 4961 946 939 L 8 3 HEL 5205 2001 3204 3181 L i Product sums HEL 6638 6590 L Picture 17 Example of a delivery ticket Please find a detailed explanation of the contents of the ticket below 1 Title of the document with the unique transaction number generated by the TTM and with the kind of transaction Delivery or Loading 2 Number of the copy not on the original printout 3 Date and time of the start and of the
19. ec oit nter niae coetui eg Dea poe eo epe eO ascen eheu d ord stP used sam Lad rese E deren cute Bag pete saad 16 5 2 Password page eet ene et utt tah hk RU ud x e RR Ek RA ux ge D pk aae 16 339 Timeand BU E ENRERE 16 3 4 DIPTADISS TERRE LIU LIU 17 3 5 Display of Dita Die E 17 3 6 Volume Change Password and Help Persistence ccsccceceeeeeeeeeeeeeeceeeeeeeaeeeeaaeeeeeeeseaeeeeeaeeeeneeees 17 3 7 Manifold Monitoring Language and User Product Count sse 17 9 8 Define Product Properties cec Geht ett bed tete abes cuve UR ROTER dg AEA EON RR RR eR nda 18 3 6 1 Standard Products SC c 18 3 8 2 User Defined Products i cic aient et etre decet cct rude cerae cbse XR a cee edes dud te Een tcx de dean 19 3 9 TTM Software Version Compartment Count Physical Product Count 19 3 10 Inclination Sensor Co ordinates and Inhibit Time ssssssssseseeeeeeeeneen nene 20 3 11 Averaging Count Wave Height and Max Duration of Power Failure essssseseeees 20 3 12 Status Display of Dip Controller nter eere rd the tcr rr nda en enne 20 9 19 HardWare Options etre ceo denne nat este fedet eae Fe esee vtae ted dre n ege uu eina uu tesa 21 9 14 SoftWare ODLOFIS erines aeieeiaii aapa ae iaa iepa dena iu utu toad 21 3 15 Digital Input Stall ceci tet ei Ee tede reed rendu patere re hee ore a tenent durar duae 22 3 16 Digital Output Status and Manipulation sssess
20. ed The values shown are briefly explained below Diptable is a brief name which may be entered during the initial verification e g for the purpose of identifying the ve hicle The text is only for information and has no influence on the measured data Inclin tab shows if an inclination table is specified the name of the correction table which is type specific and which is used to correct the volume of the primary diptable when the vehicle is not located on a flat surface ET CALIBRATION DATA 06 09 1999 15 03 Dip table NOT EUROTANK Incl table Eurotank Neste ET33345 PD4000 Softw Version 1 11 TTM Serial No Compartm Count Compartm Controller 9933092 No of products i Min Average Count s T Max perm Wave Height 3 0 mm Max Break duration 558 Max duration w o power 10 s Min Vol Change 0 0010 Controller S N 990917Mx Contr Firmware Vers 2 02 Electronic Seal 0 Comp Count Corr 9 CRC Flash ROM 49432 Tempko T 0 00100 1 0 00000 1 0 00100 1 0 00000 1 0 00000 1 0 00000 1 0 00500 1 0 00500 1 0 00500 1 CRC Checksum Manifold channel Picture 19 W amp M parameter printout Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 10 of 24 Software Vers TTM shows the version of the TTM software in use The PTB type approval is valid for versions between 1 10 and 1 19 The TTM serial number is programmed into a non alterable memory of the TTM at the time of producti
21. ed by the PTB and also fixed in the TDL Standard DIN 26051 1 It is unique for a type of product which behaves identical for the purpose of temperature compensation e g 1 Home heating oil 2 Diesel and so on M shows the calculation method being used for temperature com pensation and if compensation is done for this product at all see Manifold chan shows if manifold monitoring is enabled In this case the value is greater than zero and specifies the number of the dip controller temperature sensor input that is being used to monitor the manifold use Inclination sensor co ordinates is a table which is relevant only if inclination correction is enabled All co ordinates are given in millimetres They are specified with respect to a reference point thought to be located at the center of the liquid surface of the center sensor A detailed description can be found under 10 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 11 of 24 2 9 3 Diptables For each compartment a diptable must empirically be determined by a calibration procedure This is done once during the initial verification of the system The result is a table shown in picture 21 and stored in the TTM in a non alterable way The lines of the list are explained below Date shows date and time of the print out no meaning regarding the parameters or the time of the calibration Elektronic seal is a counter value explained in the previo
22. epending on the strength of the waves a graphic display shows the observed wave height Picture 8 Wave Level Display The example shows that the level in compartment one is still too high The weight and measures authorities require the level to stay within a 3 mm interval during the past 10 measurements for each compartment After successful completion of the initial gauging the following hint appears for a few seconds Deliuverins ptor delivery keuwti Picture 9 Help Screen during Delivery If the bottom valves are controlled by the system they are now enabled and may be opened using the pneumatic controls of the vehicle During the delivery a similar display as the compartment 4 Operation Manual DIPCHECK dated08 03 06 file q302bedienengl4 page 5 of 24 overview is shown but now instead of the loaded quantity the figures show the delivered quantity Thus the indicated quantities are 0 0 initially as shown in the following picture Picture 10 Overview Display During Delivery or Loading As in the basic state pressing a numeric key corresponding to the desired compartment number a detail screen may be called Picture 11 First Detail Screen during Delivery The value Vt is the volume delivered since the beginning of the current transaction From that value using the average temperature of the product quantity already delivered shown under Tm the temperature compensated volume Vo
23. h user defined product the up to four letters given after Abbrev may freely be selected by moving the cursor one step to the left of the character to be changed and then pressing one of the keys LOAD or UNLOAD until the desired letter is displayed The cursor may then moved one step to the left with gt and the process repeated for the next character Similarly up to four digit for a user defined product order number may be entered by positioning the cursor over the numeric field at the left end of line 2 The text given after the order number may be changed as well using the procedure described above for the Abbrev field Each user defined product must be assigned to a physical product otherwise it would not be pos sible to perform temperature compensation or to select the proper parameters for the meter if ap plicable 3 9 TTM Software Version Compartment Count Physical Product Count Picture 39 TTM SW Version Comp amp Product Count 19 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 20 of 24 PD4000 Softw Vers The number shows the version of the TTM software actually installed in the device in the example above it is V1 12 Tank Count This is the number of compartments displayed on the TTM and for selection by the numeric keys 1 4 in the example shown above No of comp This is the number of channels programmed into the dip controller Normally this number is t
24. he actual load ing state of the vehicle shows an example for such a printout The meaning of the lines are explained below 1 Title line 2 Date and time at which the document was generated Ed Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 8 of 24 3 Vehicle number 4 Driver number 5 7 Listing header line 1 STATUS REPORT Date 1 8 In compartment 1 the level of the ia product T4 is 0 0 millimetres the raw 4 as Lontainer volume calculated from the level is 22 5 a 3m litres The temperature of the pipework amp stuttgart BRYDS below the compartment not of the 7 Prod iew Ur Teen Genel d Sic product is 25 0 centigrade The spe 8 gd Mid JA ARV IL JR cific gravity of the product is 833 9 kg m 9 LOK Ok 22 20 0 833 9 1398 this is not an approved measured 10 2 BNO ix 25 1 785 8 1378 11 B x 9 25 0 792 7 1398 value and the speed of sound is 1398 m s The volume corrected for inclina 12 tion see line 13 is 22 litres ite H 783 5 1398 9 11 as line 8 but for the other compart ments of the vehicle 13 The inclination tilt of the vehicle at the moment of the measurement was 0 03 in longitudi nal direction angle positive means nose up and 0 78 in transversal direction angle positive means right side up Note the values of the status sheet are not approved and thus not enclosed in asterisks The quantities are not based on an averaged level measurement and might
25. he product may be up to four characters long and is used on the screen as well as on delivery notes to indicate which product is loaded resp has been delivered For 0001 This is a user defined order number for this product The text following home heating oil is the long name for this product The first group of physical product properties are listed in the third line Base temp Default value is 15 C but any reasonable temperature in the range 0 30 C may be entered here Meth describes the method used for temperature compensation 0 product disabled drive may not select this product 1 only uncompensated delivery 2 Product group B benzine gasoline home heating oil 3 linear compensation e g bio gasoline 4 Product group D lubricants 5 Product group X liquefied propane or butane gas In case of methods 2 4 and 5 the correction is calculated according to DIN 51757 A second screen with further properties of the physical product may be called by pressing AUTO Picture 37 Physical Product Properties 18 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 19 of 24 In the upper left corner the text O1 HEL refers to the physical product the parameters of which are shown These are Densit temperature compensation according to DIN 51757 is performed using the specific gravity or density of the product at 15 C This value may be entered
26. he same as the tank count but under special conditions e guif an additional temperature sensor input is needed for manifold monitoring the number may be higher than the tank count No of products Number of different physical products which may be selected by the driver The value 9 is the default 3 10Inclination Sensor Co ordinates and Inhibit Time Picture 40 Inclination Sensor Parameters The sketch in Fehler Verweisquelle konnte nicht gefunden werden show a typical arrangement of the three tubes of the sensor view from the top 3 11 Averaging Count Wave Height and Max Duration of Power Failure Picture 41 Averaging Count Wave Height Max duration of Power Filures Min Average Count default value 10 Number of subsequent measuring results which all must be within a range of half of the wave level given in the next pa rameter These values are averaged to yield the final value Max perm Wave Height default 10 s Maximum permissible duration of power failure during a transaction Should a power failure last longer than this time an error message Power failure will be generated printed and memorised with the data of the appropriate transaction Discon default 5 s Maximum permissible duration of a data line interruption during a transaction between TTM and dip controller If such an inter rupt lasts longer than this time an error message will be generated printed and memorised with the data of the appro
27. here The range given for the appropriate product group in DIN 51757 must be taken into account Note that this coefficient is only used for methods 2 4 and 5 Min D is the lower limit and Max D is the upper limit of the density if this value is entered manually These two parame ters are only meaningful if manual density input is activated In this case the density coefficient will be checked against these limits and rejected if it is outside the given max min interval Temp Coeff In case of linear compensation method 3 this factor is being used to calculate the temperature compensated volume 3 8 2 User Defined Products If there is more than one type of the same product which are metrologically identical but need to be distinguished on the delivery note this feature may be used First the software option user defined products must be enabled see 3 14 Picture 38 User Defined Product HEL2 It is then possible as shown in Picture 38 to select for any of the user defined products the underl ying physical product by moving the cursor into the upper left corner and pressing the keys LOAD or UNLOAD In the example of home heating oil 2 shown above which might be an ad ditivated version of the standard product the physical product is home heating oil Each physical product exists only once though several user defined products may be defined which point to one common physical product For eac
28. ich corresponds to the volume in the compartment at the time of the initial gauging in creased by hundred litres is displayed as default value For a loading transaction the default value is the total compartment volume minus 5 Any value may now be entered followed by the key The bottom valve of this compartment is now enabled and its open status will be shown in the overview The process may be repeated for the other compartments or even for the same one should the value entered need to be corrected or a delivery be continued after the pre set has been reached Using the key 0 the overview display is called 2 10 2 Entering a Customer or Depot Number If desired a customer or depot number by be printed on the delivery or loading ticket which may later help to identify the documents This number will also be memorised in the TTM The customer number may be entered after pressing the key 9 while the overview or while a detailed view of one compartment is being displayed but this must be done before the initial gauging is performed The following screen appears then 12 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 13 of 24 Lu iztomer HO n inish data entry ENC Picture 23 Entering a Customer Number Any number up to eight digits long may now be entered terminated by In case of an erroneous number the process may be repeated Typing END returns to the
29. in litres calculated from this level and the actual temperature measured below the com partment Note that the level and all values calculated from it are instantaneous values which do not compensate for any surface waves hence the accuracy is limited Pressing any numeric key corresponding to the desired compartment number calls up the detail view for that compartment Note regarding the numbering of compartments The numbering convention is usually so that compartment one is closest to the driver s cabin The compartment sequence on the overview display may be configured depend ing on the mounting location of the TTM so that number one is shown leftmost when mounted on the left side of the vehicle or vice versa recommended when TTM is mounted on the right hand side Pressing the key 0 leaves the detail view and the system returns to the overview The key causes a brief help text to be displayed which disappears automatically after 3 5 sec onds 2 4 Delivery A delivery is initiated by pressing the key DELIVERY upper left corner while the overview screen is displayed if in a detail view press 0 before The following display appears Huerasins aue levels So mm Picture 7 Info Screen Averaging The system now tries to determine a precise level by averaging the liquid levels measured every second while at the same time observing the wave height During this process which may last sev eral minutes d
30. ll points of the diptable may be displayed The meaning of the values is explained below 1 column Number of the point starting from 01 up to at max 64 2 column Height of liquid level measured during calibration 3 column Volume value which belongs to the level on the same line 4 column Gradient of the Height Volume curve measured in I mm This value is a cal culated value only and may be used to check the plausibility of the calibra tion curve The Gradient of real tanks never changes rapidly and should in the lower half increase monotonously and decrease monotonously in the upper half of the curve 3 6 Volume Change Password and Help Persistence Mi Jol Fazziord Picture 34 Volume Change Password Help Persistence Min Vol Change Default value 0 001 1 o of the total tank volume If the volume change observed between start and end of a transaction is smaller than this value the compartment contents is assumed to be unchanged Password a new password may be entered here The value 16794325 shows the default password after a master reset Help persistence Time in seconds after which help texts and hints disappear automatically 3 7 Manifold Monitoring Language and User Product Count Picture 35 Select Manifold Language Product Count 17 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 18 of 24 Manifold Channel 02 no monitoring of manifold during transacti
31. lume difference of at least 0 196 or 8 in an 8000 compartment must be observed in order to make the change meaningful Smaller differences are suppressed in order to get rid of insignificant noise which may be causes by small changes of the inclination or temperature changes during a transaction Serial number contr und Softw vers cont refer to the dip controller of the system These values will automatically be read from the dip controller and stored in the TTM on order to be able to detect the exchange of a controller An error message will be issued for each transaction should one of these values not match with the dip controller data read out before each transaction Electronic seal is a counter in the dip controller which can only be incremented The TTM incre ments it at the time of sealing or if significant dip controller parameters as e g the compartment count the incrementation is done in the dip controller With the current software version of the TTM the electronic seal is not significant as a parameter modification is impossible at all Similarly the value of the CRC value is not significant at the current stage The parameters of the nine basic products programmed into the TTM which are significant for the calculation of the temperature compensated volume and which may only be altered at the time of the initial verification are listed in the table In this table Nr refers to the metrology product code assign
32. on Changing the TTM could thus always be recognized even if all other parameters are re entered identically Compartment count and Controller Compcnt specify the number of compartments programmed into the TTM i e relevant for the graphic display and for monitoring as well as for the dip controller It might be necessary to program a greater value into the dip controller e g if collector monitoring is enabled Product count is the total number of products configured Min averaging count and max perm wave ampli specify how many subsequent measurements are to be averaged and all of which have to be between the given amplitude range in order to be ac cepted as valid gauging result Max comms interrupt specifies how many seconds an interruption of the communication between TTM and dip controller will be accepted and Max PowerOff Dur how many seconds of power fail ure will be accepted during a transaction Should one of these disturbances last longer than the given limit the transaction will automatically be closed and stored and printed accompanied by an appropriate error message Min Volume Change specifies the fraction of the total compartment volume by which the volume has to change during a transaction in order to be considered as meaningful If the decrease or in crease of the volume is smaller the quantity will be considered as zero and the compartment will not appear on the delivery ticket The value 0 001 means that a vo
33. ons Otherwise the channel number of the temperature input must be entered which is used to monitor the use of the manifold Language Use the keys LOAD and UNLOAD to select the desired language for the user dialogue The cursor position is irrelvant for this selection Having made a new choice for the language press END and then power down the unit to initialise the new language buffer User product count Number of user definable products valid only if software option user prod uct has been activated 3 8 Define Product Properties 3 8 1 Standard Products Using this and the next screen the properties and the delivery mode of each of the products may be defined In this section we deal with the standard products i e with the software option user de fined products disabled Picture 36 Standard Product Properties The meaning of the data displayed is described below 01 HEL is the physical product currently selected No 01 is the user product code currently selected If the option user defined products is enabled these two figures may be different see next section Otherwise they are always equal user product physical product In order to select the next previous product number place the cursor over the nu meric value after No in Picture 36 and press the buttons LOAD UNLOAD until the desired product is displayed The properties of this product may now be modified Abbrev This abbreviation for t
34. or axis in mm Computed values Vt Volume in horizontal position computed using the internal diptable 14 Operation Manual DIPCHECK dated08 03 06 file q302bedienengl4 page 15 of 24 Vkor Volume corrected for the given inclination angles WL and WQ Korr relative inclination correction in according to the formula 100 Vkor Vt Vt 2 11 3 Inclinometer Display From the trip data screen press the key in order to obtain the display of the actual measuring results of the inclination sensor Picture 28 Inclinometer Result Display The meaning of the values is Long Tran Inclination angles for longitudinal and transversal inclination of the vehicle See 2 11 2 an explanation of the definition of these angles Press END when through 2 11 4 Display of Approval Signs Digital Type Label From within the trip data display press the key PRE SET to obtain the following display of the approval signs for the system DircCheck 4 412 EURO CEZICATA 23 05 TAHE Picture 29 Digital Type Label Values shown To the left the type of device DipCheck and the manufacturer name are shown Inthe middle the approval sign of the national type approval of the PTB for DipCheck is dis played andto the left the approval sign of the measuring container is shown in the example there is no approval yet thus the manufacturer is indicated Press END when ready 15 Operation Manu
35. page 12 of 24 2 10 Optional Functions and Data Input 2 10 1 Quantity Predetermination Hint Though this function is always available entering any pre set val ues is only meaningful if the system is installed as to directly con trol the bottom valves of the tank container Otherways entering a quantity pre set will not have any consequences and is thus use less After the initial gauging of a delivery of a loading a quantity may be pre set for each compartment When this quantity has been delivered or been loaded the bottom valves are automatically closed by the TTM Use one of the keys 1 7 to select the detail view for the desired compartment Now press PRE SET and observe the following screen Picture 21 Quantity Preset first disable delivery It shows that the system already has enabled the bottom valve which is always automatically done right after the initial gauging simply because most of the deliveries are without quantity pre set Therefore the delivery has first to be stopped by hitting the END key If a pre set value shall be entered for all or at least for most of the compartments the key PANIC may be used to stop all deliveries at once Now press PRE SET again which calls the following screen radtuct glume Pre set T65 e Picture 22 Entering a Quantity Pre set Value The cursor will automatically be positioned on the field for the pre set value During a delivery a value wh
36. pera ture may be freely selected as well Prod Gr B desired product group input value may be selected by use of f and U To Base temperature numeric input value Do specific gravity of the product at base temperature numeric input value T product temperature numeric input value Vt raw volume at the temperature T numeric input value Vo Volume compensated to base temperature will be re computed by the TTM after any change of the given input values To modify any of the input values select the appropriate numeric field using the cursor control keys and gt then enter the desired numeric value followed by The new value for Vo will instan taneously appear Press the END button when through to return to the overview 2 11 2 Inclination Correction From within the trip data screen press LOAD in order to call the following screen Hint the data displayed are manually entered and are thus not related to the actual fill ing state or the inclination situation of the vehicle Picture 27 Inclination Correction Calculator Input values comp Number of the compartment for which the inclination correction is performed The desired compartment may be selected by use of ff and lU WL Angle for longitudinal inclination positive if driver s cabine is elevated WQ Angle for transversal inclination positive if right hand side is elevated Levl Liquid level in this tank measured along the sens
37. priate transaction 3 12Status Display of Dip Controller Picture 42 Status Display of Dip Controller Dip contr SW Ver 1 94 or 2 0x according to PTB approval 20 Operation Manual DIPCHECK dated08 03 06 file xq302bedienengl4 page 21 of 24 Serial number e g 80212 005 this number is electronically stored in the dip controller and may be read out at any time Seal Counter In the dip controller an electronic counter is incremented every time when the electronic seal is broken and a parameter is modified These values are read out and stored in the non volatile memory of the TTM at the time of sealing Before every transaction these stored values are compared with those in the real dip controller Any deviation will lead to an error message both on the screen as well as on the printout if any is generated 3 13Hardware Options rx Oo OOO 1 in 1 iam E 2 LI Picture 43 Hardware Configuration Options This screen may be used to configure the hardware options of the system as e g printer inclination sensor and other peripherals Using the keys and gt one of the 16 options may be chosen The meaning of the selected bit marked by the cursor will be shown in the bottom line Pressing the keys 1 or 0 will activate or deactivate the option chosen The complete list of all selectable options follows 3 14 Software Options Picture 44 Software Configuration Options This screen may be u
38. sed to configure the software options of the system as e g temperature com pensation and other functions Using the keys and gt one of the 16 options may be chosen The meaning of the selected bit marked by the cursor will be shown in the bottom line Pressing the keys 1 or 0 will activate or deactivate the option chosen The complete list of all selectable options follows Temperature Comp This option is only used to control the printout of tickets The compen sation method configured for each product takes precedence over this option If the option is set only Vt or Vo is printed depending on the compensation method of the product If the option is not set and if the product is configured as temperature compensated both Vo and Vt are printed Inclination correction Activates the inclination correction for the vehicle The proper inclination correction table must be compiled into the system Mirror compartments if activated the compartments on the overview are displayed from right to left compartment 1 rightmost If the TTM is mounted on the right side of the vehicle mirroring may be useful Print temp and density not yet supported User defined products when activated additional products may be defined by the user e g several gasoline products standard sulphur free winter may be ek 21 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 22 of 24 defined which
39. sssssssees ener nnne nnne 22 4 Table of GMS TRS cree eee Kn Ps 23 5 Table ol PiChuvGs er 24 223 Operation Manual DIPCHECK dated08 03 06 file xq302bedienengl4 page 24 of 24 5 Table of Pictures Picture 1 Keyboard and display of the TANK TRUCK MANAGER ccccceseceeeeeeeeeeeeeeeeeeeeeeeeeeeeecaeeeneeeeeeeeeeeeeeedueeeenes 1 Picture 2 Logo Display after Power p iis isis ie meine dete ette enki de cured ck nn hirundo emer 3 Picture 3 Version Display afteer Power Up eeeseeeeseesescieseeeeseeeee einen nennen ennemi enne innen cnn cann 3 Picture 4 Short From Help Text ssiri smcesoirssi nipende aiai eiaeiiai iisipin ii AA 3 Picture 5 Loading Status Display ci ann em AS cte Ve ceni secet FEE ie ee tige EE Eoo RYE eg 3 Picture 6 Detail Screen in Idle St te 2 recense pere ipee pese certo ke eae 4 Picture 7 Info Screen AVERAGING iu inei tetce etx dte crum en tcu eda CRI B Re e eene de eR D a SER det ERR R a d aee Rag eaaa 4 Picture 8 Wave Level DIS PIA vis H 4 Picture 9 Help Screen during Deliverys niteen insna ngeia ae re nnne nn rns nnne tn resi tte aSa aaa nisaar 4 Picture 10 Overview Display During Delivery or Loading seseeeeeeeeneeeeenneeneen nennen nennen crines 5 Picture 11 First Detail Screen during Delivery rns ctc errare cin et at rae p ev Ua ENONSE EE sees ESE S olm cs 5 Picture 12 Resid
40. t Eie 13 Picture 27 Temperature Compensation Calculator esses nnne nnne nnne nnns nnne nnne nennen 14 Picture 28 Inclination Correction Calculatot 12 2inuni rice etin rein Licet emet tete Ie ente aa Re dna tua Lie nae ode sra aUe kc ENER 14 Picture 29 Inclinometer Result Display sxc etaient oerte anima netur tete Frame xr eau cp nen a ux ea deny En E 15 Picture 30 Digital Type Label d reci cate pet quus met A teas ed ex trees gt nies O REED eases 15 Picture 31 Password Entry SCFeeln cese de nete tuendi domi Eee epo qve case ede pa ces a pe VE at ru esso EX ee e Ed Ls reared 16 Picture 32 Entry of Time and Dale ie Eee tte Ecrit an een hon ee 16 Picture 33 Diptable Display of Compartment no sessesssessseseseeeeeeeeee nnne nennen nest nter se ntis nnne nnns enne 17 Picture 34 Diptelle Display m CL 17 Picture 35 Volume Change Password Help Persistence cccccsccceeseeeeeeeneeeeeseeeeeecaeeeceeaeeeseneaeeescaeeesecaeeeseenseeesenseeeese 17 Picture 36 Select Manifold Language Product Count cccceesceeeeeeeeeeeeaeeeeeneeeeescaeeesecaeeeseseeeeesceeeesscaeeeeenneeessenseeeeoes 17 Picture 37 Standard Product Propertie Sisri ciini mien ein elie el eed dedi eee 18 Pict re 38 Physical Product Properties iii licite eee t IIa slap ee ette ee ea aa e n e a R a bat lebdecehag 18 Picture 39 User Delined aree Ureii
41. tion The final gauging takes now place in this case it might take a minute until the waves produced during loading have been calmed down When this is done the TTM displays the loaded quantities for the first com partment as shown in Picture 14 Other compartments may be inspected and a loading ticket may be printed as described above in 2 4 2 6 Trip Data Pressing the key AUTO during display of the loading status overview the following input screen appears Picture 16 Input of Trip Information The most recently entered values are shown and may now be changed by the following procedure 1 Using the keys gt and the cursor i e the black rectangle can be moved over the number to be modified 2 f the cursor is not in the proper line it can be moved to the next line by overrunning the line end with the 5 Similarly moving the cursor with the beyond the start of a line causes it to reappear at the end of the preceding line Moving the cursor past the end of the last line will cause it to reappear at the top left corner and vice versa 3 Using the numeric keypad type in the desired number The figures appear at the cursor loca tion asterisks indicate the width of the field available A greater number than permitted may be entered but will lead to the display of a number like 9999 4 Any typing error may be corrected with the key CE and starting over 5 The value just typed in appears at th
42. tity Delivered from a Compartment If a printer is connected to the system and if a delivery note shall be printed press PRINT while any of the compartment quantities is indicated Any number of copies of the delivery note may be produced by repeatedly pressing that key See under 2 7 for an example and an explicationO of the delivery document Press the END key to finalize the delivery and return to the overview screen 5 Operation Manual DIPCHECK dated08 03 06 file q302bedieneng 4 page 6 of 24 2 5 Loading Loading is performed in a rather similar way as delivering Press the LOAD key to start loading which starts the initial gauging process Unless there is residual product in the compartments the averaging should finish quickly no products no waves During the loading transaction the products loaded may be entered by first selecting the desired compartment typing in the appropriate number key 1 7 for example 1 Picture 15 Entering the Products during Loading Using the keys lt and gt the desired product may be selected As soon as it is displayed in the upper right corner the next compartment may be selected and the process repeated or the product input may be terminated by pressing 0 which brings up the overview again Any errors of the product assignment may be corrected at any time during the loading procedure When loading is done press the END key in order to finalize the transac
43. ual Quantity within the Compartment ssssssessseeseeeeeeeeneennenen nennen nennen nennen nennen cand 5 Picture 13 Display for compartment without change eessesseeeeeeeeeeeeeeeeeeeeenenennne ninm nn nnnm tenerent RR 5 Picture 14 Display of Quantity Delivered from a Compartment sssssssssseeeeeeee nenne eene nennen 5 Picture 15 Entering the Products during loading ioc eterne reine aeaaaee iana aia t 6 Picture Te Input ot Lrip ntOFmiatiOh uoce odio io Crete terreur Cre e repete vereinen ae O redet br eie ni Reve edes Ere IRURE e rs cee 6 Picture 17 Example of a delivery ticket eicere ctae ctam eter Rande eene qn eC a tu da cun d n RR e kde Reis 7 Picture 18 Status Sheet PrihtoUt neret teer ocn eei REY edd cix pR ECCO ne Fehler Textmarke nicht definiert Picture 22 Quantity Preset first disable delivery eee eeccceeseseneeeeeeteseeeeaeeteneeeeaeeseaeeseaeeseaeeeeaeeseaeeeeaeeseaeeeeaeeseaeeeeaeetes 12 Picture 23 Entering a Quantity Pre set Value ssssssssssseseeenenennnen nennen nennen nennt nn nene tnnt reset nnns 12 Picture 24 Entering a Customer Number nennen nennen nnne nre s Enae Madiona rese nnns s enne 13 Picture 25 Memory Rec ll Last Transactloti 5 ns i eio Ferte titre Er pedir treni ec repe The te Use ieget xis ink x ep De Rea ER 13 Picture 26 Memory Recall Single Compartime itt 5 2 1 cuente tote eripi ceret atte nets rri etaa keai vau
44. us paragraph Max Volume is the maximum volume in the compartment It is used for internal computations and should be the highest value observed rounded up to the next multiple of 100 or 500 litres Max level is a similar value corresponding to the sensor height rounded up to the next multiple of 50 or 100 m Diptable for Comp 1 Date 06 09 1999 Smallest meas quant is the value fixed at the time of the initial 15201 verification according to the approval of DipCheck Currently Electronic Seal the smallest measurable quantity is a quarter of the max permit mi ted compartment loading volume the value might be smaller than Max Height the parameter max volume and is usually close to the upper inser ME most point of the diptable Sensor No P NET Address Pipework vol is the volume in litres that is contained in the pipe bum work between the bottom valve and API coupler The diptable is mE measured using bottom loading and thus includes this volume Since the pipework becomes empty during the first delivery the is volume must be taken into account in case of the first delivery by 2 98 3 39 adding it to the difference volume 3 83 4 15 Sensor no and P NET Address specify from which sensor con 18 4 50 nected to which controller the gauging levels of this compartment E B de may be read in in principle any connection is possible even if it 52 5 41 is strongly recommended to use input
Download Pdf Manuals
Related Search
DIPCHECK dip check dip check meaning dip checklist dip check in quality dip check full form dip check in bpo dip check images dip check acronym dip check report dip check clip art dip check meaning in bpo dip check full form in bpo